交变力磁力显微镜动态成像技术的研究

近年来磁力显微镜(magnetic force microscopy,MFM)对动态磁场信号的测量与分析由于其特殊的工业要求和重要用途而受到广泛关注,本文旨在利用交变磁力对磁性探针的周期性调制发展一种交变力磁力显微镜技术,为磁信息存储工业等重要领域关键技术的发展提供新型的有力的工具.与目前标准MFM采用的设计思路不同,本文的关键在于合理利用MFM频率调制机理,优化设计MFM磁性探针,并且引入动态信号处理模块,实现对交变磁场信号的MFM成像.为达到这些目的,需要从理论上研究MFM探针的频率调制机理,并由实验上设计出动态信号提取模块,二者相辅结合优化设计出具有动态信号测试和分析能力的交变力磁力显微镜技术,由此来测量和解释纳米尺度磁畴结构.     

Hard disk magnetic domain nano-spatial resolution imaging by using a near-field scanning microwave microscope with an AFM probe tip

A near-field scanning microwave microscope (NSMM) incorporating an atomic force microscope (AFM) probe tip was used for the direct imaging of magnetic domains of a hard disk under an external magnetic field. We directly imaged the magnetic domain changes by measuring the change of reflection coefficient S₁₁ of the NSMM at an operating frequency near 4.4 GHz. Comparison was made to the magnetic force microscope (MFM) image. Using the AFM probe tip coupled to the tuning fork distance control system enabled nano-spatial resolution. The NSMM incorporating an AFM tip offers a reliable means for quantitative measurement of magnetic domains with nano-scale resolution and high sensitivity.     

Advantages of CNT-MFM probes in observation of domain walls of soft magnetic materials

The advantage of the CoFe-coated carbon nanotube (CNT) probes in a magnetic force microscope (MFM) is verified on in-plane magnetized soft magnetic materials. CoFe-coated CNT, standard and low-moment MFM probes were used to observe closure domains in square and rectangular Permalloy elements. The perturbative effect of the CNT-MFM probe was far less than that of a standard MFM probe. Domain walls were clearly observed as a pair of dark and bright lines which was in agreement with the micromagnetic simulations. The vortex core was also clearly observed using the CNT-MFM probes.     

Computer simulation of magnetic force microscopy images with a static model of magnetization distribution and dipole-dipole interaction

An algorithm for computer simulation of images obtained by magnetic force microscopy (MFM) is suggested. It is based on the Brown formalism and takes into account the shapes and the magnetic properties of the MFM tip and sample studied. The robustness and efficiency of the algorithm are tested by simulating the MFM image of a point magnetic dipole for the case where the tip is approximated by a nonmagnetic truncated cone covered by a thin uniformly magnetized layer. From the computer simulation of the MFM images of the dipole, the optimum parameters of the MFM probe are obtained.     

Spin domain mapping of a CrO2 thin film using spin-polarized current microscopy

We investigate spin domain mapping of a CrO₂ thin film using spin-polarized current microscopy at room temperature, where conductive atomic force microscopy (CAFM) with a CrO₂-coated tip is used. The nanoscale spin domains of the CrO₂ thin film were crosschecked by magnetic force microscopy (MFM). Notably, the CAFM exhibits the spin domains of the CrO₂ thin film with higher resolution than the MFM, which may result from a local point contact between the nanoscale CrO₂-coated tip and surface of the CrO₂ thin film.     

Direct observation of room temperature magnetism in (In,Mn)As thin films by magnetic force microscopy

Variable-temperature magnetic force microscopy (MFM) has been performed over the temperature range of 298-348 K on ferromagnetic (In,Mn)As thin films deposited by metal-organic vapor phase epitaxy (MOVPE). Ferromagnetic domains were observed with submicron resolution in both single and two phase (In,Mn)As films, persisting up to 328 K. Isolated cylindrical domains ranging from 100 to 350 nm in diameter with densities of 2-5 × 10⁸ cm⁻² were observed in phase pure films. Longer range magnetic order, in the form of ribbon-like domains up to 1 μm in length, are present in the regions between the cylindrical domains. Two phase (In,Mn)As films produced a well-resolved complex domain structure consisting of 180° parallel and antiparallel domains. Excellent agreement between the temperature dependence of the relative magnetization obtained by MFM and superconducting quantum interference device measurements was observed.     

Magnetization reversal of ferromagnetic nanoparticles under inhomogeneous magnetic field

We investigated remagnetization processes in ferromagnetic nanoparticles under inhomogeneous magnetic field induced by the tip of magnetic force microscope (MFM) in both theoretical and empirical ways. Systematic MFM observations were carried out on arrays of submicron-sized elliptical ferromagnetic particles of Co and FeCr with different sizes and periods. It clearly reveals the distribution of remanent magnetization and processes of local remagnetization of individual ferromagnetic particles. Modeling of remagnetization processes in ferromagnetic nanoparticles under magnetic field induced by MFM probe was performed on the base of Landau–Lifshitz–Gilbert equation for magnetization. MFM-induced inhomogeneous magnetic field is very effective to control the magnetic state of individual ferromagnetic nanoparticles as well as to create different distribution of magnetic field in array of ferromagnetic nanoparticles.     

Micromagnetic study of effect of tip-coating microstructure on the resolution of magnetic force microscopy

The properties of a magnetic force microscopy (MFM) tip are very important for high-resolution magnetic imaging. In this work, micromagnetic models of tips are set up to study the effect of tip-coating microstructure, especially the randomness of anisotropy on tip edge and tip end, on the resolution of MFM. The effective coating height and the resolution potential of tips with various microstructures and magnetic properties have been characterized by investigating the obtained signals from high-density continuous granular thin film disk media with a bit size of 8×16 nm² and bit-patterned media with a pattern period p of 50 nm. The magnetic moment distribution at the tip end should be perpendicular to the sample to realize a ‘magnetically sharp’ tip, which explains further the improved resolution in the recent experimental reports. Tips with well-controlled grain structure and magnetic anisotropy of coating materials can be applied to both high-density thin film disk media and bit-patterned media.     

Magnetic elements for switching magnetization magnetic force microscopy tips

Using combination of micromagnetic calculations and magnetic force microscopy (MFM) imaging we find optimal parameters for novel magnetic tips suitable for switching magnetization MFM. Switching magnetization MFM is based on two-pass scanning atomic force microscopy with reversed tip magnetization between the scans. Within the technique the sum of the scanned data with reversed tip magnetization depicts local atomic forces, while their difference maps the local magnetic forces. Here we propose the design and calculate the magnetic properties of tips suitable for this scanning probe technique. We find that for best performance the spin-polarized tips must exhibit low magnetic moment, low switching fields, and single-domain state at remanence. The switching field of such tips is calculated and optimum shape of the Permalloy elements for the tips is found. We show excellent correspondence between calculated and experimental results for Py elements.     

Optimization of perpendicular magnetic anisotropy tips for high resolution magnetic force microscopy by micromagnetic simulations

Magnetic Force Microscopy (MFM) tip coated with perpendicular magnetic anisotropy film (PMA tip) is one of the choices for high resolution imaging at low scan height (SH), since it has negligible tip–sample interaction related to its stable magnetic state, sharp, and small tip stray field. In this work, detailed micromagnetic studies are carried out to understand the effect of geometrical and magnetic parameters including the cone angle θ of the PMA tip, intergrain exchange constant $A_{2}^{*}$ , saturation magnetization M _s and uniaxial crystalline anisotropy constant K ₁ of the tip coating on the MFM tip resolution. To evaluate the resolution performance of the optimized PMA tip, MFM images of high-density granular recording media and patterned media are simulated. We find that, for the PMA tip and its coating, a cone angle in a range of 36.9^° to 53.1^°, a saturation M _s of 700 emu/cm³, a large uniaxial crystalline anisotropy constant K ₁ (>4.9×10⁶ erg/cm³) and a high intergrain exchange constant $A_{2}^{*}$ of (0.3–1.0)×10^?6 erg/cm are optimized conditions for high resolution imaging. The optimized PMA tip has an excellent performance on imaging of high-density thin film media (bit size of 8×16 nm²) at low SH of 2–8 nm and bit pattern media with a pitch of 50 nm, edge-edge spacing of 5–15 nm at SH of 8–15 nm.     

Using a nanoscale extraordinary hall effect sensor to measure the tip field of a magnetic cantilever

The spatial distribution of the magnetic field around the tip of a magnetic cantilever coated with a cobalt film 50 nm thick is investigated using an FePt extraordinary Hall effect sensor. The magnetic field’s dependence on the distance between the sensor’s surface and the MFM cantilever is measured and found to be inversely proportional to the cubic distance, as predicted in theory. The magnetic field measured on the MFM cantilever tip is found to be 0.02 T.     

In-plane magnetic pattern separation in NiFe/NiO and Co/NiO exchange biased bilayers investigated by magnetic force microscopy

Ion bombardment induced magnetic patterning (IBMP) was used to write in-plane magnetized micro and submicron patterns in exchange biased magnetic bilayers, where the magnetization directions of the adjacent patterns are antiparallel to each other in remanence. These magnetic patterns were investigated by non-contact magnetic force microscopy (MFM). It is shown that the recorded MFM images of the IBMP patterns in two exemplarily chosen standard layer systems (NiFe (4.8 nm)/NiO (68 nm) and Co (4.8 nm)/NiO (68 nm)) can be well described by a model within the point-dipole approximation for the tip magnetization. For 5 and 0.9 μm wide bar patterns the domain wall widths between adjacent magnetically patterned areas were determined to a≈1 μm. The minimum magnetically stable pattern width was estimated to be 0.7 μm in the standard system Co (4.8 nm)/NiO (68 nm).     

MFM probe control of magnetic vortex chirality in elliptical Co nanoparticles

Magnetic force microscopy (MFM) methods were applied to investigate the peculiarities of magnetization distribution in elliptical 400×600×27 nm Co particles. Reversible transitions between the uniform and vortex states under inhomogeneous magnetic field of MFM probe were observed. Possibility to control the chirality of a magnetic vortex in these particles by MFM probe manipulation was shown.     

Microstructure and magnetic property of electroless-plated CoNiFeB soft underlayer

An electroless-plated CoFeNiB film as a soft underlayer in perpendicular magnetic recording is studied by magneto-optical Kerr effect microscope, magnetic force microscopy (MFM), and transmission electron microscopy. A stray field is evidently suppressed for the anisotropic CoFeNiB film, which is under an applied field during the plating process. The lines of magnetic flux show that the Ni seed layer have no intrinsic effect on the homogenous magnetic state of the CoFeNiB layer. The interaction between a MFM tip and the CoFeNiB layer is clearly observed by electron holography indicating the excellent soft magnetic properties required by the soft underlayer.     

In situ magnetic hysteresis measurement of magnetic tips in magnetic force microscope

In situ magnetic hysteresis measurements of magnetic tips in a magnetic force microscope (MFM) are demonstrated using alternating gradient force magnetometry. The measured magnetic moments of MFM tips are estimated in the range from 10⁻⁶ to 10⁻⁵ emu by this technique and the whole MFM tips in cantilevers are considered to be measured from the value of measured magnetic moments. The relationship between the magnetic hysteresis loops of MFM tips and those of coated magnetic films is discussed.     

Multiscale magnetic domains observed in die-upset melt-spun magnets using magnetic force microscopy

Magnetic force microscopy (MFM) has been used to examine the magnetic reversal process in samples of Nd_13.9(Fe₉₂Co₈)_80.3B_5.5Ga_0.5, one made by hot-pressing and one made by thermomechanical deformation, or die-upsetting. Both samples were imaged in various magnetic states under zero-field conditions. In both the hot-pressed and die-upset samples, the finest scale contrast observable consisted of individual magnetic clusters of approximately 10 grains in volume, on a scale between 150 and 300 nm. In the hot-pressed sample this fine-scale contrast was similar regardless of the magnetic state of the sample and no larger-scale contrast was observed, indicating that exchange interactions do not greatly affect the locality of the magnetic reversal in this sample. The die-upset sample in the thermally demagnetized state showed only fine-scale magnetic contrast. Once the sample was saturated, however, interaction domains formed which extended over many microns, although the fine-scale contrast could still be observed within these larger interaction domains. The increased crystallographic alignment between grains in the die-upset sample as compared with the hot-pressed sample, underlies the hypothesis that intergranular exchange interactions cause the reversal to be localized at the peripheries of previously reversed regions, leading to the creation of large interaction domains.     

Field-variable magnetic domain characterization of individual 10 nm Fe_3O_4 nanoparticles

The local detection of magnetic domains of isolated 10 nm Fe_3O_4 magnetic nanoparticles(MNPs) has been achieved by field-variable magnetic force microscopy(MFM) with high spatial resolution.The domain configuration of an individual MNP shows a typical dipolar response.The magnetization reversal of MNP domains is governed by a coherent rotation mechanism, which is consistent with the theoretical results given by micromagnetic calculations.Present results suggest that the field-variable MFM has great potential in providing nanoscale magnetic information on magnetic nanostructures,such as nanoparticles, nanodots, skyrmions, and vortices, with high spatial resolution.This is crucial for the development and application of magnetic nanostructures and devices.     

Temperature dependence of the stability of written bits in a magnetic hard-disk medium investigated by magnetic force microscopy

The thermal stability of written bits in a magnetic hard-disk medium has been investigated with a magnetic force microscope (MFM), which was equipped with an in situ heating system capable of heating the medium up to 300 °C. It is shown that both the annealing temperature and the duration have significant effect on the decay of the MFM signal. No signal decay is observed when annealing for 30 min up to temperatures of 200 °C. The MFM signal decays rapidly with increasing temperature, for temperatures over 200 °C. Repeated annealing at 280 °C with a duration below 10 min does not cause any signal decay.     

Experimental determination of ultra-sharp stray field distribution from a magnetic vortex core structure

The fine magnetic stray field from a vortex structure of micron-sized permalloy (Ni₈₀Fe₂₀) elements has been studied by high-resolution magnetic force microscopy. By systematically studying the width of the stray field gradient distribution at different tip-to-sample distances, we show that the half-width at half-maximum (HWHM) of the signal from vortex core can be as narrow as ∼21 nm at a closest tip-to-sample distance of 23 nm, even including the convolution effect of the finite size of the magnetic tip. a weak circular reverse component is found around the center of the magnetic vortex in the measured magnetic force microscope (MFM) signals, which can be attributed to the reverse magnetization around the vortex core. Successive micromagnetic and MFM imaging simulations show good agreements with our experimental results on the width of the stray field distribution.     

Towards a quantitative analysis of magnetic force microscopy data matrices

Fast and efficient software tools previously developed in image processing were adapted to the analysis of raw datasets consisting of multiple stacks of images taken on a sample interacting with a measuring instrument and submitted to the effect of an external parameter. Magnetic force microscopy (MFM), a follow-up of atomic force microscopy (AFM), was selected as a first testbed example. In MFM, a specifically developed ferromagnetic scanning tip probes the stray magnetic field generated from a ferromagnetic specimen. Raw scanning probe images taken on soft patterned magnetic materials and continuous thin films were used, together with synthetic patterns exploited to assess the absolute performance ability of the proposed texture analysis tools. In this case, the parameter affecting the sample-instrument interaction is the applied magnetic field. The application discussed here is just one among the many possible, including, e.g., real-time microscopy images (both optical and electronic) taken during heat treatments, phase transformations and so on. Basically any image exhibiting a texture with a characteristic spatial or angular dependence could be processed by the proposed method. Standard imaging tools such as texture mapping and novel data representation schemes such as texture analysis, feature extraction and classification are discussed. A magnetic texture stability diagram will be presented as an original output of the entropic analysis on MFM datasets.