Gas permeability of cupric ion containing HTPB based polyurethane membranes

For the purpose of oxygen enrichment from air, the gas permeability and selectivity of an ionic polyurethane membrane was under investigation. Membranes of ionic polyurethane were prepared by step-growth polymerization of hydroxyl terminated polybutadiene (HTPB) and 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI). The ionic group was introduced by adding N-methyldiethanolamine (MDEA) as the chain extender of which the tertiary amines were complexed with cupric ions. The effect of hard segment content, polymerization method, peroxide introduction, and the amount of cupric ion on gas permeability were investigated. It was found that the binding of hard segment and the flexibility of soft segments had subtle effects on gas permeability. Membranes of the same composition were synthesized through two different procedures, one- and two-stage polymerization. The former contains large hard segment of cluster aggregation and flexible soft segments had a higher gas permeation rate. When a crosslinker, benzoyl peroxide, was added, the crosslinkage within soft segments hindered cluster formation by hard segment aggregation, the permeability increased. Furthermore, CuCl₂ addition enhanced hard segment aggregation, more hard segments formed cluster aggregates and less dispersed in soft segment region, which also increased permeability. However, excess CuCl₂ addition resulted in CuCl₂ piling up in the soft segment region, which restricted the movement of soft segments and therefore reduced the gas permeability.     

Properties of ZnO nanocrystals prepared by radiation method

Zinc oxide nanoparticles were prepared by irradiation of aqueous solutions containing zinc(II) ions, propan-2-ol, polyvinyl alcohol, and hydrogen peroxide. Zinc oxide was found in solid phase either directly after irradiation, or after additional heat treatment. Various physicochemical parameters, including scintillation properties of prepared materials, were studied. After decomposition of impurities and annealing of oxygen vacancies, the samples showed intensive emission in visible spectral range and well-shaped exciton luminescence at 390–400 nm. The best scintillating properties had zinc oxide prepared from aqueous solutions containing zinc formate as initial precursor and hydrogen peroxide. Size of the crystalline particles ranged from tens to hundreds nm, depending on type of irradiated solution and post-irradiation thermal treatment.     

Three-dimensional mesoporous titanosilicates prepared by modified sol-gel method: Ideal gold catalyst supports for enhanced propene epoxidation

Mesoporous titanosilicates with 1-12 mol % Ti content and with three-dimensional wormhole-like mesoporosity are prepared by a modified sol-gel technique. Sorption analysis shows that there is little change in the surface properties with increasing Ti concentration in the samples, implying that Ti atoms either are well-dispersed on the walls of the silica matrix or are present inside the framework with no pore blocking effect. Spectroscopic analysis shows that the Ti atoms are atomically dispersed in the silica matrix even at very high Ti concentration and there is no observable Ti aggregate (anatase) present in the samples. These titanosilicate samples after Au deposition followed by trimethylsilylation (for enhanced hydrophobicity) are highly efficient catalysts for vapor-phase propene epoxidation using O2 and H2. It was possible to achieve commercially desirable performance with about 7% propene conversion, >90% propene oxide selectivity, and about 40% hydrogen efficiency.     

Properties of solvent based polyurethane adhesives containing fumed silicas

Five hydrophilic and two hydrophobic fumed silicas of different surface area and particle size were added to solvent based polyurethane adhesives. Silica addition produced a noticeable increase in the adhesive viscosity, imparted negative thixotropy, increased the storage modulus (G') and improved the green adhesion of chlorinated rubber/PU adhesive/chlorinated rubber joints. Those modifications were more pronounced in the adhesives which contain hydrophilic silicas.     

Properties of water-in-oil (W/O) nano-emulsions prepared by a low-energy emulsification method

Properties of water-in-oil (W/O) nano-emulsion formed by a low-energy emulsification method are described in this work. Nano-emulsions have been formed in water/mixed non-ionic surfactant/decane. Several mixtures of Span 20, Span 80, Tween 20 and Tween 80 were studied. Phase behavior studies and stability studies allowed to determine zones where nano-emulsions can be formed. Bluish and transparent W/O nano-emulsion with droplet sizes as low as 30 nm was formed. Nano-emulsion droplet size was measured by Dynamic Light Scattering. Nano-emulsions stability was studied by multiple light scattering and by dynamic light scattering. The results showed the evolution with time of the average radius droplet. The nano-emulsions prepared showed high kinetic stability for weeks, without phase separation, sedimentation or creaming. Nevertheless, their droplet size increased slightly over time. Stability studies show that nano-emulsion breakdown could be attributed to Ostwald ripening and coalescence mechanism, depending on the water concentration.     

Extraction of phenols using polyurethane membrane

The extraction of various phenols from aqueous and organic solutions using polyurethane membrane has been investigated. The effects of solution concentration, extraction time, surface area, pH, salts, and temperature on extraction were studied. The phenols are extracted as neutral species and the extraction is governed by a combined effect of intra- and intermolecular hydrogen bonding and nonspecific hydrophobic interactions. The ether-type membrane showed higher extraction capability for the phenols than the ester-type polyurethane membrane.     

Preparation of an efficient nanofiltration membrane based on blending of polysulfone and polysulfone-g-butylacrylate prepared by ATRP

Polysulfone is one of the most common used polymers for preparation of nanofiltration membranes. These membranes are highly susceptible to fouling problems because of their surface hydrophobic nature. In this paper a new approach for modification of polysulfone to overcome the fouling problems was introduced. The modification was carried out via blending of polysulfone with a modified grafted polysulfone using atom transfer radical polymerization (ATRP) method. The modified grafted polysulfone was synthesized via ATRP grafting of n-butylacrylate from chloromethylated polysulfone. The graft copolymers were characterized by FT-IR, NMR, DSG and TGA techniques. Furthermore, surface morphology and performance of the corresponding membrane were studied in detail using SEM and pure water flux and salt rejection experiments, respectively. The results indicated that the prepared modified polysulfone membranes have high surface hydrophilicity and therefore better fouling resistance and very good water permeability.     

Properties of nanostructured GaN prepared by different methods

Various methods have been employed to prepare nanostructured GaN exhibiting reasonable surface areas. The methods include ammonolysis of γ-Ga₂O₃ or Ga₂O₃ prepared in the presence of a surfactant, and the reaction of a mixture of Ga₂O₃ and Ga(acac)₃ with NH₃. The latter reaction was also carried out in the presence of H₃BO₃. All the methods yield good GaN samples as characterized by X-ray diffraction, electron microscopy and photoluminescence measurements. Relatively high surface areas were obtained with the GaN samples prepared by the ammonolysis of γ-Ga₂O₃ (53 m² g⁻¹), and of Ga₂O₃ prepared in the presence of a surfactant (66 m² g⁻¹). GaN obtained by the reaction of NH₃ with a mixture of Ga₂O₃, Ga(acac)₃ and boric acid gave a surface area of 59 m² g⁻¹. GaN nanoparticles prepared by the nitridation of mesoporous Ga₂O₃ samples generally retain some porosity.     

Photothermal and photocatalytic processes on TiO2 based materials prepared by sol-gel method

In the present work, Fe³⁺ doped TiO₂ coatings on glass substrates were prepared by dip-coating from a sol-gel solution. The influence of the dopant concentration on the structure, optical, photocatalytic and photothermal properties of the films was studied. The results obtained have shown a strong correlation between the catalytic properties and the amount of iron dopant and the temperature of the thermal treatment.     

An investigation into the sorption of benzoic acids by polyurethane membrane

The extraction mechanism of organic compounds by ether- and ester-type polyurethane membrane has been investigated through a detailed study of sorption of monobromobenzoic acids. The effects of solution concentration, extraction time, surface area, pH, salts, and temperature on extraction were studied. It was found that monobromobenzoic acids are extracted in their neutral form, and that the extraction is controlled primarily by the relative strength of intra- and intermolecular hydrogen bonding. The ether-type polyurethane membrane allows a more efficient removal of monobromobenzoic acids from solution than the ester-type membrane. The extraction of benzoic acids with the ether-type membrane decreases as the temperature increases. When the ester-type polyurethane membrane is used, an extraction maximum is observed at room temperature with a decrease in extraction at lower and higher temperatures.     

Highly selective olefin epoxidation with aqueous H2O2 over surface-modified TaSBA15 prepared via the TMP method

Trialkylsiloxy-modified Ta(v) centers on mesoporous silica exhibit excellent selectivity for epoxide formation (>98% after 2 h) in the oxidation of cyclohexene using aqueous H2O2 as the oxidant; the modified catalysts exhibit an increased lifetime, retaining high selectivity after 6 h of reaction (>95% epoxide).     

Antibacterial thermoplastic polyurethane electrospun fiber mats prepared by 3-aminopropyltriethoxysilane-assisted adsorption of Ag nanoparticles

Antibacterial thermoplastic polyurethane(TPU) electrospun fiber mats were prepared by adsorption of Ag nanoparticles(Ag NPs) onto TPU/3-aminopropyltriethoxysilane(APS) co-electrospun fiber mats from silver sol. The use of APS can functionalize TPU fibers with amino groups, facilitating the adsorption of Ag NPs. The effects of p H of silver sol and APS content on Ag NP adsorption and antibacterial activity were investigated. Ag NP adsorption was evidenced by TEM, XPS and TGA. Significant Ag NP adsorption occurred at p H = 3-5. The main driving force for Ag NP adsorption is electrostatic interaction between ―NH3~+ of the fibers and ―COO-derived from the ―COOH group capped on the surfaces of Ag NPs. The antibacterial activity of the Ag NP-decorated TPU/APS fiber mats was investigated using both gram-negative Escherichia coli and gram-positive Bacillus subtilis. The antibacterial rate increases with increasing APS content up to 5% where the antibacterial rates against both types of bacteria are over 99.9%.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

利用模板法制备Ag纳米线

利用阳极氧化铝（AAO）作为模板,制备出高定向的Ag纳米线．Ag纳米线的形貌由环境扫描电镜证实,并通过X-射线能谱（EDX）、X-射线粉末衍射谱（XRD）测试手段进行了表征．     

Properties of PVC. I. Properties of PVC films prepared by casting and by precipitation

This investigation compares the properties of PVC films prepared both by casting from tetrahydrofuran solution and from samples obtained by precipitation with properties of samples from the original PVC. The differences in properties are explained on the basis of solvent residues remaining in the samples even after tempering at higher temperatures and after extremely long times of drying. Attention was given to the difficulties caused by this fact, namely, in observing the influence of molecular weight and of distribution of molecular weights of fractions on PVC properties. Reasons were given for the retention of the tetrahydrofuran by PVC.     

Transport of organic dyes through ether-type polyurethane membrane

Transport of various anthraquinone, acidic and basic dyes in aqueous solution through ether-type polyurethane membrane has been studied to better define the factors affecting the removal of organic compounds by the polyurethane membrane and to complement the previously proposed sorption mechanism. The effects of pH, salts, dye geometry and size, initial dye concentration, thickness of the membrane, and solution temperature on the rate of transport were investigated. Transport was found to be dependent upon the pH conditions of the starting and the receiving solutions. An increased rate of transport was observed with increased solution temperature and with the use of a thinner polyurethane membrane. The differences in the rates of transport can be attributed to the relative solubility of the organic dyes in the membrane and in solution, and to the strength and extent of intermolecular interactions with the polymer. Dye concentration, geometry and size, and the presence of salts in solution had no significant effect on the rate of transport. All of the studied dyes were found to exist as neutral species in the membrane.     

Properties of calcium fluoride-filled cross-linked plasticized polyurethane

Thermal and physicomechanical properties of plasticized polyurethane based on oligo(butadiene)diol prepolymer and oligoethertriol were examined as influenced by microdispersed calcium fluoride. Introduction of this filler substantially improved the physicomechanical properties of the polyurethane compositions.     

A nanofibrous composite membrane of PLGA-chitosan/PVA prepared by electrospinning

Tissue engineering scaffolds produced by electrospinning feature a structural similarity to the natural extracellular matrix. In this study, poly(lactide-co-glycolide) (PLGA) and chitosan/poly(vinyl alcohol) (PVA) were simultaneously electrospun from two different syringes and mixed on the rotating drum to prepare the nanofibrous composite membrane. The composite membrane was crosslinked by glutaraldehyde vapor to maintain its mechanical properties and fiber morphology in wet stage. Morphology, shrinkage, absorption in phosphate buffered solution (PBS) and mechanical properties of the electrospun membranes were characterized. Fibroblast viability on electrospun membranes was discussed by MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide] assay and cell morphology after 7 days of culture. Results indicated that the PBS absorption of the composite membranes, no matter crosslinked or not, was higher than the electrospun PLGA membrane due to the introduction of hydrophilic components, chitosan and PVA. After crosslinking, the composite membrane had a little shrinkage after incubating in PBS. The crosslinked composite membrane also showed moderate tensile properties. Cell culture suggested that electrospun PLGA-chitosan/PVA membrane tended to promote fibroblast attachment and proliferation. It was assumed that the nanofibrous composite membrane of electrospun PLGA-chitosan/PVA could be potentially used for skin reconstruction.     

Separation performance of polyimide composite membrane prepared by dip coating process

The effects of the preparation conditions in a dip coating process on polyimide composite membranes have been investigated. Polyimide precursor obtained from pyromellitic dianhidride (PMDA) and 4,4′-oxydianiline (ODA) was mixed with triethylamine and poly(amic acid)tri-ethylamine salt (PAA salt) was made. An asymmetric polyimide membrane (PI-2080) as a supporting membrane was dipped in a PAA salt (concentration 0–5 wt.%) methanol solution. The coating layers of PAA salt were converted to these of polyimide by annealing at 200°C for 3 h in an ordinary vacuum oven.The performance of the polyimide composite membrane was evaluated by gas permeation (N₂, O₂, CO₂, at 1 kg/cm²) and pervaporation (feed: a 95 vol.% ethanol aqueous solution at 30–60°C). The composite membranes prepared using a coating solution of 5 wt.% PAA salt showed the CO₂/N₂ selectivity of over 25 on gas permeation, and separation factor α (H₂O/EtOH) of over 800 with a total flux of 0.21 kg/m² h on pervaporation.     

Preconcentration and separation of acaricides by polyether based polyurethane foam

This paper reports the preconcentration of some dissolved organic phosphorous and chlorinated acaricides in water by porous polyether based polyurethane foam. Preliminary screening tests on the retention of the tested compounds, i.e., dicofol and bromopropylate, by polyether foams indicated that a very high percent removal of the tested species was obtained. The retention rate was found fast and reaches equilibrium in a few minutes. The various parameters, e.g., pH, extraction media, shaking time, salt effect, temperature and sample volumes affecting the preconcentration of the tested species by the unloaded foam, trioctylamine and trimethylphosphate treated foam have been optimized via batch modes of separation. The unloaded foams were employed in column modes for the retention and recovery of the tested species. The sorption efficiency and recovery of the compounds by the unloaded foams column were found to be up to 97.5%. The height equivalent to a theoretical plate (HETP) obtained by the unloaded foam was found to be in the range 1.1-1.3 ± 0.2 mm. The sorption mechanism of the tested compounds by the foams was discussed.