Texture evolution in Mg–Mn and Mg–Mn–Ce alloys and the effect of as-cast grain size

Texture evolution in rolled (400°C) and annealed (450°C) Mg–1% Mn-based alloys containing different levels of Ce was examined. It was found that Ce refines the as-cast and rolled/annealed grain structure. The overall intensity of the basal texture decreases with Ce additions in both the rolled and subsequently annealed condition. A strong relationship was found between maximum intensity (M) of rolling and annealing textures and the as-cast effective grain size, d?′, i.e. M?∝?e^{0.4 d ?′} (R ^2?=?0.8), which was attributed to the role of plastic compatibility stresses which lead to grain boundary deformation altering the balance of deformation modes. Contributions from Ce solute effects and lattice parameter changes are also discussed.     

Precipitation and fracture behaviour of Fe–Mn–Ni–Al alloys

The effects of Al addition on the precipitation and fracture behaviour of Fe–Mn–Ni alloys were investigated. With the increasing of Al concentration, the matrix and grain boundary precipitates changed from L1₀ θ-MnNi to B2 Ni₂MnAl phase, which is coherent and in cube-to-cube orientation relationship with the α′-matrix. Due to the suppression of the θ-MnNi precipitates at prior austenite grain boundaries (PAGBs), the fracture mode changed from intergranular to transgranular cleavage fracture. Further addition of Al resulted in the discontinuous growth of Ni₂MnAl precipitates in the alloy containing 4.2?wt.% Al and fracture occurred by void growth and coalescence, i.e. by ductile dimple rupture. The transition of the fracture behaviour of the Fe–Mn–Ni–Al alloys is discussed in relation to the conversion of the precipitates and their discontinuous precipitation behaviour at PAGBs.     

Hardness and microstructural variation of Al–Mg–Mn–Sc–Zr alloy

Variations of Vickers hardness were observed in Al–Mg–Mn alloy and Al–Mg–Mn–Sc–Zr alloy at different ageing times, ranging from a peak value of 81.2 HV at 54 ks down to 67.4 HV at 360 ks, below the initial hardness value, 71.8 HV at 0 ks for the case of Al–Mg–Mn–Sc–Zr alloy. Microstructures of samples at each ageing stage were examined carefully by transmission electron microscopes (TEMs) both in two-dimensions and three-dimensions. The presence of different types, densities, and sizes of particles were observed dispersed spherical Al₃Sc_1−xZr_x and also block-shaped Al₃Sc precipitates growing along <1 0 0>_Al with facets {1 0 0} and {1 1 0} of the precipitates. TEM analysis both in two-dimensions and three-dimensions, performed on various samples, confirmed the direct correlation between the hardness and the density of Al₃Sc.     

Phase transformations and structure of Ni–Mn–In alloys with varying ratio Ni/Mn

The fine structure of Ni–Mn–In alloys has been studied when manganese atoms are substituted for nickel atoms in an annealing state. The concentration dependence of the critical temperatures and the structures of the alloys have been discussed. It has been found that, as manganese atoms replace nickel atoms, the structure after annealing is changed from a two-phase (L2₁ + martensite) to single-phase L2₁ structure. The martensitic transformation in Ni₄₇Mn₄₂In₁₁ alloy is accompanied by the formation of modulated 14M martensite.     

Magnetic and structural properties of Pd–Mn–Sn intermetallics compounds

Magnetic and structural properties of Heusler Pd_0.5Mn_{0.5- x} Sn _x with x = 0.05, 0.10, 0.17, 0.20 and 0.25, have been studied by magnetisation and X-ray diffraction measurements at room and low temperatures. The crystal structure at room temperature is L2₁ cubic phase for x = 0.17, 0.20, 0.25 and B2 cubic phase for x = 0.10. Martensite structure 10M, was observed at room temperature for x = 0.05. X-ray measurements at low temperatures revealed a structural transformation from B2 to 14M for the x = 0.10 case. The lattice parameter of the L2₁ phase decreases linearly with the concentration, x. A ferromagnetic behaviour has been detected for L2₁ compounds, but the ferromagnetic exchange characteristic of each composition is of different strength. This gives rise to different Curie temperatures.     

Thermal and microstructural investigation of Cu–Al–Mn–Mg shape memory alloys

There are many studies to improve the properties of Cu–Al–Mn shape memory alloys, such as high transformation temperatures, ductility and workability. Most of them have been performed by adding a quaternary component to the alloy. In this study, the effect of trace Mg addition on transformation temperatures and microstructures of three different quaternary Cu–Al–Mn–Mg alloys has been investigated using thermal analysis, optical microscopy and XRD techniques. The transformation temperatures are within the range of 120–180 °C, and they have not changed significantly on decreasing the Mn content, replacing with Mg. The fine precipitates have been observed in the alloys with the Mg content up to 1.64 at%. Calculated entropy change and XRD analysis reveal that the alloys with high Al content have mainly 18R-type structure which could be responsible for good ductility and workability.     

Crystal and Magnetic Structures of Granular Powder Spinel Mn–Zn and Ni–Zn Ferrites

Some specific features of the crystal and magnetic structures of granular powder spinel-like ferrites Mn_0.160Mg_0.404Zn_0.448Fe₂O₄, Mn_0.676Zn_0.227Fe_0.09Fe₂O₄, Mn_0.5792Zn_0.2597Fe_0.1612Fe₂O₄, and Ni_0.32Zn_0.68Fe₂O₄ have been studied by neutron diffraction. It has been established that the crystal structure of all the studied compounds has a cubic symmetry with space group Fd\(\bar 3\)m. Ferrimagnetic ordering is observed in all the studied structures. Based on the experimental data, the unit cell parameters and interatomic bond lengths of the studied compounds are determined alongside with the distribution of cations between octahedral and tetrahedral crystallographic positions in their cubic crystal structure. Corresponding average magnetic moments are calculated for different positions in their cubic structure. Some structural mechanisms of the formation of magnetic properties depending on the level of doping and the size of powder grains are discussed.     

Dislocation climb and low-temperature plasticity of an Al–Pd–Mn quasicrystal

Dislocations and phason faults have been studied by transmission electron microscopy in an Al-Pd-Mn sample deformed at 300°C under a high pressure. All dislocation movements have occurred by climb, in contrast with the usual interpretations of dislocation motion in quasicrystals. Several modes of dissociation and decomposition of dislocations have been observed, allowing for estimations of phason fault and antiphase-boundary energies. Work softening is tentatively explained in terms of a varying chemical stress.     

Structural and magnetic properties of nanostructured Mn–Al–C magnetic materials

Pre-alloyed Mn_50+x−yAl_50−xC_y   (x=0$x=0$, 2, 4, 6, 8; y=0$y=0$, 1.7, 3) powders were mechanically milled (MM), and the as-milled powders subsequently annealed at temperatures from 350 to 600 °C to produce the ferromagnetic metastable L1₀-structured τ-phase. Bulk Mn₅₄Al₄₆ specimens were also annealed under the same conditions for comparison. The effects of the Mn concentration and C additions on phase formation, microstructure, magnetic properties, as well as on the magnetization mechanism of the Mn–Al–C alloys were systematically investigated. It was found that the magnetic properties are strongly dependent both on the fraction of the τ-phase and its microstructure. There exists a strong influence of the microstructural refinement, due to the ball milling, on the rate of ε-phase to τ-phase transformation and on the stability of the τ-phase. The kinetics of formation and subsequent decomposition of the magnetic τ-phase were markedly different in the MM and bulk alloys. Both remanence curves and δM plots showed no exchange coupling among the τ-phase nanograins. The mechanism for the magnetization process was determined to be domain wall pinning.     

ICEMS study of isothermal oxidation of Fe–Mn–Al–C–Cr–Si–Mo, Fe–Mn–Al–C–Cr–Si and Fe–9Cr–1Mo alloys

The purpose of this paper is to investigate the isothermal behavior of Fe–27.3Mn–7.6Al–C–6.5Cr–0.25Si–0.88Mo (Mo(0)) and Fe–27.3Mn–7.6Al–1.0C–6.5Cr–0.25Si (Mo(1)) alloys and compare it against Fe–9Cr–1Mo (FCR) commercial alloy. The experiments were carried out at 600°C, 700°C, 750°C and 850°C, each one during 72 h in static air. The oxidation kinetics was measured as a function of time using a Thermogravimetry analyzer (TGA). The structure and composition of the oxide scale were characterized by X-ray diffraction (XRD) and Integral Conversion Electron Mössbauer Spectroscopy (CEMS). The TGA results show that at all oxidation temperatures the sample FCR exhibit the lowest kinetic corrosion and the lowest weight gain, whereas Mo(0) the highest. By CEMS technique it were found a broad magnetic sextet, which has been fit by one hyperfine field distribution with mean hyperfine field characteristic to ferritic/martensite phase, one Fe^3?+? doublet and one singlet for the Mo(0) and Mo(1) alloys. Samples oxidized at highest temperatures exhibit a strong paramagnetic line, probably due that the Cr or Mn oxides may be enriched on the surface. Then, the magnetic phase can be converted partially into austenite phase at highest temperatures.     

Effect of irradiation on microstructure and hardening of Cr–Fe–Ni–Mn high-entropy alloy and its strengthened version

ABSTRACT

A single-phase fcc high-entropy alloy (HEA) of 20%Cr–40%Fe–20%Mn–20%Ni composition and its strength with yttrium and zirconium oxides version was irradiated with 1.4?MeV Ar ions at room temperature and mid-range doses from 0.1 to 10 displacements per atom (dpa). Transmission electron microscopy (TEM), scanning transmission electron microscopy with energy dispersive X-ray spectrometry (STEM/EDS) and X-ray diffraction (XRD) were used to characterise the radiation defects and microstructural changes. Nanoindentation was used to measure the ion irradiation effect on hardening. In order to understand the irradiation effects in HEAs and to demonstrate their potential advantages, a comparison was performed with hardening behaviour of 316 austenitic stainless steel irradiated under an identical condition. It was shown that hardness increases with irradiation dose for all the materials studied, but this increase is lower in high-entropy alloys than in stainless steel.     

Mn–ferrite nanoparticles via reverse microemulsions: synthesis and characterization

Mn–ferrite nanoparticles were synthesized by thermal treatment at 800 °C of manganese and iron oxo-hydroxides obtained via water-in-oil microemulsions consisting of n-hexanol as continuous phase, cetyl trimethyl ammonium bromide (CTAB) as the cationic surfactant and aqueous solutions of metal salts and precipitant agent (tetramethyl ammonium hydroxide) as reagents. Nanoparticles were synthesized using a multi-microemulsion approach. Two different co-precipitation routes are described depending on the Fe(II) or Fe(III) precursor salts. The influence of salt concentration and digestion process on the final products was examined. The nanoparticles were characterized by X-ray diffraction accompanied by Rietveld analysis, transmission electron microscopy, thermal analysis, infrared spectroscopy, and SQUID magnetometry. In all the synthesis reported in this study MnFe₂O₄ was observed only after thermal treatment at 800 °C of the as-prepared precursors. Almost spherical nanocrystalline MnFe₂O₄ ranging from 12 to 39 nm was obtained starting from chlorides or mixed chloride–sulfate salts as precursors. Low values of reduced remanent magnetization (M _r/M _s) and coercive field (H _c) induce to believe that a fraction of superparamagnetic particle is present at room temperature.     

The transport and magnetic properties of La–Pb–Mg–Mn–O manganites at low temperatures

The structure, transport properties and the magnetoresistance behavior in the temperature interval 77–400 K of the perovskite-like lanthanum manganites La_0.6Pb_0.4−xMg_x+yMnO₃ (x=0, 0.1, 0.2 and y=0, 0.2) were investigated. Polycrystalline bulk samples were prepared by sol–gel self-combustion and subsequent heat treatment at 1000 °C for different times, 40, 80, 160 and 320 min. All manganites exhibit a peak in the resistivity around 200–250 K, below the ferromagnetic ordering temperature (320–330 K). An isotropic and negative magnetoresistance has been observed in all compounds. Magnetoresistance MR exhibits a peak in the temperature range 130–150 K, below SC–metal transition temperature. Magnitude of MR at the peaks was nearly 27% in the magnetic field of 2 T. At room temperature, a magnetoresistance of 9.5% for La_0.6Pb_0.2Mg_0.2MnO₃ composition was obtained. Longer heat treatment time enhanced the magnetorezistive properties.     

Mechanical properties of ferrite-perlite and martensitic Fe–Mn–V–Ti–C steel processed by equal-channel angular pressing and high-temeperature annealing

Using the method of equal-channel angular pressing (ECAP), submicrocrystalline structure is formed in lowcarbon Fe–Mn–V–Ti–C steel with the average grain size 260 nm in the ferrite-perlite state and 310 nm in the martensitic state. It is established that the ECAP treatment gives rise to improved mechanical properties (H_μ = 2.9 GPa, σ₀ = 990 MPa in the ferrite-perlite and H_μ = 3.7 GPa, σ₀ = 1125 MPa in martensitic states), decreased plasticity, and results in plastic flow localization under tensile loading. The high strength properties formed by the ECAP are shown to sustain up to the annealing temperature 500°C.     

Correction to scaling critical exponents and amplitudes for amorphous Fe–Mn–Zr alloys

Asymptotic and leading correction to scaling critical exponents and amplitudes have been determined for quenched amorphous Fe_90−yMn_yZr₁₀ (y=0–8) ferromagnets through an elaborate analysis of temperature dependence of spontaneous magnetization, zero-field susceptibility and low-field AC susceptibility data obtained in the asymptotic critical region. From this analysis, it is found that the values of the critical exponents and amplitudes do not depend on the alloy composition and are in good agreement with the values predicted for three-dimensional Heisenberg ferromagnet system. The observed experimental results are consistent with the concept of scaling in that the exponent equalities β=γ(δ−1) and α=2(1−β)−γ are obeyed to a high degree of accuracy. These results show that both amorphous and crystalline materials behave similarly in the critical region though amorphous alloys show a wide asymptotic critical region than the crystalline materials. The presence of disorder does not seem to have any influence on critical behavior of the system investigated in the present work.     

Influence of Cr on microstructure and elastocaloric effect in Ni–Mn–In–Co–Cr polycrystalline alloys

Ni–Mn-based metamagnetic shape memory alloys have been proposed as potential elastocaloric refrigerants. The intrinsic brittleness of the alloys has limited their cooling application. Introducing a soft second phase is an effective way to reduce the brittleness. From the viewpoint of application, the effect of second phase on elastocaloric effect should be illustrated. In this paper, we have investigated the microstructure, martensitic transformation and elastocaloric effect of Ni₄₅Mn_37-xIn₁₃Co₅Cr_x ($x=0,1\text{ and }2$) polycrystalline alloys. Single-phase and precipitates-containing microstructures are obtained for the undoped and doped alloys, respectively. The precipitates in Cr-doped alloys enhances the fracture strength but significantly hinders the martensitic transformation. Balancing the fracture strength and martensitic transformation, the Ni₄₅Mn₃₆In₁₃Co₅Cr alloy with small amount of precipitates along grain boundaries exhibits large cooling effects of 4–6 K in the temperature range of 317–353 K.     

Synthesis of high quality and monodisperse CdS:Mn/ZnS and CdS:Mn/CdS core–shell nanoparticles

CdS:Mn²⁺/ZnS and CdS:Mn²⁺/CdS core–shell nanoparticles were synthesized in aqueous medium via chemical precipitation method in an ambient atmosphere. Polyvinylpyrrolidone (PVP) was used as a capping agent. The effect of the shell (ZnS and CdS) thickness on CdS:Mn²⁺ nanoparticles was investigated. Inorganically passivated core/shell nanocrystals having a core (CdS:Mn²⁺) diameter of 4 nm and a ZnS-shell thickness of ∼0.5 nm exhibited improved PL intensity. Optimum concentration of doping ions (Mn²⁺) was selected through optical study. For all the core–shell samples two emission peaks were observed, the first one is band edge emission in the lower wavelength side due to energy transfer to the Mn²⁺ ions in the crystal lattice; the second emission is characteristic peak of Mn²⁺ ions (⁴T₁ → ⁶A₁). The XRD, TEM and PL results showed that the synthesized core–shell particles were of high quality and monodisperse.     

Magnetic and mechanical properties of Ni–Mn–Ga/Fe–Ga ferromagnetic shape memory composite

A ferromagnetic shape memory composite of Ni–Mn–Ga and Fe–Ga was fabricated by using spark plasma sintering method. The magnetic and mechanical properties of the composite were investigated. Compared to the Ni–Mn–Ga alloy,the threshold field for magnetic-field-induced strain in the composite is clearly reduced owing to the assistance of internal stress generated from Fe–Ga. Meanwhile, the ductility has been significantly improved in the composite. A fracture strain of 26% and a compressive strength of 1600 MPa were achieved.