Straightforward synthesis of conductive graphene/polymer nanocomposites from graphite oxide

The reduction of graphite oxide (GO) in the presence of reactive poly(methyl methacrylate) (PMMA), under mild biphasic conditions, directly affords graphene grafted with PMMA. The resulting nanocomposite shows excellent electrical conductivities resulting from the optimal dispersion and exfoliation of graphene in the polymer matrix.     

还原态氧化石墨烯载Pd纳米催化剂对甲酸氧化的电催化性能

采用改进的Hummers法氧化石墨后,对其超声剥离成氧化石墨烯水溶液,继之通过乙二醇还原Pd金属离子和氧化石墨烯,得到了还原态氧化石墨烯（RGO）负载Pd纳米催化剂,并用于甲酸的电催化氧化.透射电子显微镜和X射线衍射结果显示：负载于RGO上的Pd粒子平均粒径为3.8nm,其优先在RGO的褶皱和边缘处生长.电化学测试表明：RGO上残存的含氧基团降低了Pd催化剂受CO毒化的程度,Pd/RGO催化剂表现出了较商业化Pd/C更高的电催化活性和更好的稳定性.     

Peculiar reduction of graphene oxide into graphene after diffusion in exponentially growing polyelectrolyte multilayers

In the present work, in situ reduction of graphene oxide (GO) into graphene was preformed, after diffusion in exponentially growing polyelectrolyte multilayers, using sodium citrate as the reducing agent. First, the graphene oxide was obtained by treating a commercial grade of Expanded Graphite (EG). Based on XRD and Raman spectroscopy results, a complete exfoliation of graphene nanopellets down to one layer was achieved during the oxidation process. Secondly, the diffusion of GO was carried out in an exponentially growing polyelectrolyte multilayer film made from poly(diallyldimethylammonium chloride) as the polycation and from poly(acrylic acid) as the polyanion. Electrical conductivity of the GO based films was measured during the reduction process as a function of time. The conductivity reached values of the order of 10(-4) S cm(-1), whereas the pristine polyelectrolyte multilayer was highly insulating (～10(-8) S cm(-1)). The conductivity also reached a maximal value after about 24 h of reduction and decreased for longer reduction duration. Some tentative explanations for this peculiar finding will be given.     

The Formation of Large‐Area Conducting Graphene‐Like Platelets

The treatment of a suspension of graphite oxide (GO) with sodium azide leads to a material that, after reduction, features amino groups at the top and bottom of the sheets. These groups react through microcontact printing with an isothiocyanate monolayer on a silicon oxide substrate to form covalent bonds that strongly attach to the particles on the surface. With ultrasonication it is possible to obtain exfoliation of the sheets that are not covalently bound to the surface leaving single‐layer platelets attached to the substrate. The azido derivative can be also used to functionalize the graphene oxide with long alkylic chains through a click chemistry approach. This functionalization results in the exfoliation of this material in dimethylformamide. The novel materials were fully characterized by different techniques including IR spectroscopy, thermogravimetric analysis (TGA), scanning and transmission electron microscopy (SEM and TEM), X‐Ray photoelectron spectroscopy (XPS), and solid state NMR spectroscopy. The material with amino groups, after the reduction step, is conductive with a resistivity only approximately seven times larger than that of unprocessed graphite. This implies that after reduction of the GO, the conjugated sp² network is largely restored. We consider this to be an important step towards a chemical approach for forming conducting large‐area platelet films of single‐layer graphene.     

功能型单层石墨烯的热剥离法制备及其超电容性能

以氧化石墨(GO)作为前驱体,在两种不同热剥离温度下制备了两类功能型单层石墨烯.其中第一类功能型单层石墨烯通过在较低温度及空气气氛下热剥离GO制备;第二类功能型单层石墨烯通过在氮气保护下高温热剥离GO得到;利用氮气吸附-脱附方法测定了两类样品的比表面积,利用电化学测试方法分析了其超电容性能.结果表明,通过低温热剥离的方式即可以有效剥离GO;两类样品均具有较高的BET比表面积.低温热剥离GO所制备的功能型单层石墨烯在2 mol/L KOH体系中的最大比电容值约为220 F/g;而通过高温热剥离GO所制备的功能型单层石墨烯虽然同样具有较高的BET比表面积,但其最大比电容值下降至约150 F/g.这表明通过低温热剥离GO所制备的功能型单层石墨烯具有更优异的超电容性能.     

Functionalized single graphene sheets derived from splitting graphite oxide

A process is described to produce single sheets of functionalized graphene through thermal exfoliation of graphite oxide. The process yields a wrinkled sheet structure resulting from reaction sites involved in oxidation and reduction processes. The topological features of single sheets, as measured by atomic force microscopy, closely match predictions of first-principles atomistic modeling. Although graphite oxide is an insulator, functionalized graphene produced by this method is electrically conducting.     

Carcinogenic Organic Residual Compounds Readsorbed on Thermally Reduced Graphene Materials are Released at Low Temperature

The preliminary oxidation of graphite to graphite oxide followed by a thermal exfoliation is one of the methods most frequently employed in the preparation of graphene. Such thermally reduced graphene can be widely used for several applications that range from coatings to sensing device fabrication. It is therefore important to investigate in detail the fabrication procedure, the structural features of the resulting graphene, and its potential toxicological effects. Low‐molecular‐weight and carcinogenic compounds are known to be generated during the thermal reduction/exfoliation of graphite oxide. Such compounds are readsorbed onto the reduced material during the cooling process. We investigate here the composition of the organic compounds that are adsorbed onto the graphene material and show that they can be easily released during the following processing steps even at temperatures as low as 50 °C. Some of the released organic compounds are classified as highly carcinogenic. The results shown here are important not only from a chemical point of view to better understand the composition and properties of the graphene material produced, but also to bring attention to the potential toxicological effects that the synthesis itself or the post‐production processes can cause.     

High-yield synthesis of few-layer graphene flakes through electrochemical expansion of graphite in propylene carbonate electrolyte

High-yield production of few-layer graphene flakes from graphite is important for the scalable synthesis and industrial application of graphene. However, high-yield exfoliation of graphite to form graphene sheets without using any oxidation process or super-strong acid is challenging. Here we demonstrate a solution route inspired by the lithium rechargeable battery for the high-yield (>70%) exfoliation of graphite into highly conductive few-layer graphene flakes (average thickness <5 layers). A negative graphite electrode can be electrochemically charged and expanded in an electrolyte of Li salts and organic solvents under high current density and exfoliated efficiently into few-layer graphene sheets with the aid of sonication. The dispersible graphene can be ink-brushed to form highly conformal coatings of conductive films (15 ohm/square at a graphene loading of <1 mg/cm(2)) on commercial paper.     

Influence of parent graphite particle size on the electrochemistry of thermally reduced graphene oxide

Electrochemical applications of graphene are of very high importance. For electrochemistry, bulk quantities of materials are needed. The most common preparation of bulk quantities of graphene materials is based on oxidation of graphite to graphite oxide and subsequent thermal exfoliation of graphite oxide to thermally reduced graphene oxide (TR-GO). It is important to investigate to which extent a reaction condition, that is, composition of the oxidation mixture and size of graphite materials, influences the properties of the resulting materials. We characterised six graphite materials with a range of particle sizes (0.05, 11, 20, 32, 35 and 41 μm) and the TR-GO products prepared from them by use of scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. Cyclic voltammetric performance of the TR-GO samples was compared using ferro/ferricyanide and ascorbic acid. We observed no correlation between size of initial graphite and properties of the resultant TR-GO such as density of surface defects, amount of oxygen-containing groups, or rate of heterogeneous electron transfer (HET). A positive correspondence between HET rate and high defect density as well as low amounts of oxygen functionalities was noted. Our findings will have profound influence upon practical fabrication of graphene for applications in sensing and energy storage devices.     

Precise Tuning of Surface Composition and Electron‐Transfer Properties of Graphene Oxide Films through Electroreduction

Graphene materials are generally prepared from the exfoliation of graphite oxide (GO) to graphene oxide, followed by subsequent chemical or thermal reduction. These methods, although efficient in removing most of the oxygen functionalities from the GO material, lack control over the extent of the reduction process. We demonstrate here an electrochemical reduction procedure that not only allows for precise control of the reduction process to obtain a graphene material with a well‐defined C/O ratio in the range of 3 to 10, but also one that is able to tune the electrocatalytic properties of the reduced material. A method that is able to precisely control the amount and density of the oxygen functionalities on the graphene material as well as its electrochemical behaviour is very important for several applications such as electronics, bio‐composites and electrochemical devices.     

氧化石墨烯在辣根过氧化物酶传感器中的应用研究

本文研究氧化石墨烯的合成方法及其在生物传感器中的应用.通过Hummer法氧化天然石墨粉制得氧化石墨,在蒸馏水中利用超声分散将氧化石墨剥片,从而合成了氧化石墨烯(GO).通过透射电镜图表征了氧化石墨烯的形貌并通过红外光谱证实氧化石墨烯的形成.将所合成的氧化石墨烯与三角形貌的金纳米颗粒(prism AuNPs)、辣根过氧化...     

PS colloidal particles stabilized by graphene oxide

Exfoliated graphene oxide (GO) sheets with hydrophilic functional groups on the surface were prepared by the oxidation of graphite. Because of the hydrophilic groups on the sheets and the hydrophobic carbon surface, GO sheets were located at the oil-water interface and could be used as a stabilizer in Pickering emulsions. After the Pickering emulsion polymerization of styrene, PS colloidal particles with GO sheets on the surface were prepared. The size of the GO sheets exerts an important influence on the preparation of PS colloidal particles. Small GO sheets located at the liquid-liquid interface and GO-stabilized PS colloidal particles were prepared; however, for large GO sheets, smaller PS colloidal particles prepared on the GO surface were observed. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used to characterize the structure and morphology of the colloidal particles. TEM, SEM, and XPS results all suggest the successful preparation of GO-stabilized PS colloidal particles.     

Facile photoreduction of graphene oxide by an NAD(P)H model: Hantzsch 1,4-dihydropyridine

To make "clean" reduced GO sheets in high quality and in large scale, a natural reduced nicotinamine adenine dinucleotide NAD(P)H model, Hantzsch 1,4-dihydropyridine (HEH), is used as a mild organic photoreductant in this work. Benefiting from the intense absorption of HEH in the range of 300-420 nm, the graphene oxide (GO) can be readily reduced by HEH under UV light irradiation (λ > 320 nm) to afford single or few-layer reduced graphene oxide at room temperature. Studies on reduction extent reveal that both irradiation time and concentration ratio of HEH to GO are important for effective reduction of GO under UV light. The as-prepared photochemically reduced graphene oxide (PRGO) dispersion is stable without the need for any polymeric or surfactant stabilizers. Simply by extraction treatment, the "clean" PRGO sheets can be obtained in large quantities, and its conductivity approaches to 4680 S·m(-1) that is the highest value reported by photochemical approaches so far.     

The Route to Functional Graphene Oxide

We report on an easy‐to‐use, successful, and reproducible route to synthesize functionalized graphite oxide (GO) and its conversion to graphene‐like materials through chemical or thermal reduction of GO. Graphite oxide containing hydroxyl, epoxy, carbonyl, and carboxyl groups loses mainly hydroxyl and epoxy groups during reduction, whereas carboxyl species remain untouched. The interaction of functionalized graphene with fluorescent methylene blue (MB) is investigated and compared to graphite, fully oxidized GO, as well as thermally and chemically reduced GO. Optical absorption and emission spectra of the composites indicate a clear preference for MB interaction with the GO derivatives containing a large number of functional groups (GO and chemically reduced GO), whereas graphite and thermally reduced GO only incorporate a few MB molecules. These findings are consistent with thermogravimetric, X‐ray photoelectron spectroscopic, and Raman data recorded at every stage of preparation. The optical data also indicate concentration‐dependent aggregation of MB on the GO surface leading to stable MB dimers and trimers. The MB dimers are responsible for fluorescence quenching, which can be controlled by varying the pH value.     

Electrochemical reduction of graphene oxide and its electrochemical capacitive performance

A convenient method for the production of graphene is developed using the electrochemical reduction of graphite oxide (GO) in solution without assembling it onto the electrode. The samples were examined by X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. The results show that the number of oxygen functional groups can be significantly decreased. The electrochemical capacitance of the prepared graphene after 8 h of reduction is 158.5 F g^?1 at 0.5 A g^?1, much higher than that of GO and carbon nanotubes. The mechanism for this reaction is also proposed in this paper.     

Preparing graphene oxide–copper composite material from spent lithium ion batteries and catalytic performance analysis

The wide use of lithium ion batteries (LIBs) has created much waste, which has become a global issue. It is vital to recycle waste LIBs considering their environmental risks and resource characteristics. Anode graphite from spent LIBs still possess a complete layer structure and contain some oxygen-containing groups between layers, which can be reused to prepare high value-added products. Given the intrinsic defect structure of anode graphite, copper foils in LIB anode electrodes, and excellent properties of graphene, graphene oxide–copper composite material was prepared in this work. Anode graphite was firstly purified to remove organic impurities by calcination and remove lithium. Purified graphite was used to prepare graphene oxide–copper composite material after oxidation to graphite oxide, ultrasonic exfoliation to graphene oxide (GO), and Cu²⁺ adsorption. Compared with natural graphite, preparing graphite oxide using anode graphite consumed 40% less concentrated H₂SO₄ and 28.6% less KMnO₄. Cu²⁺ was well adsorbed by 1.0 mg L^?1 stable GO suspension at pH 5.3 for 120 min. Graphene oxide–copper composite material could be successfully obtained after 6 h absorption, 3 h bonding between GO and Cu²⁺ with 3/100 of GO/CuSO₄ mass ratio. Compared to CuO, graphene oxide–copper composite material had better catalytic photodegradation performance on methylene blue, and the electric field further improved the photodegradation efficiency of the composite material.     

Electrocatalytic Activities of Chemically Reduced Graphene Are Essentially Dominated by the Adhered Carbonaceous Debris

Due to its simple, scalable, and facile qualities, the chemical reduction of graphene oxide seems to be the most popular approach to prepare graphene. We show that such prepared graphene is strongly adhered with carbonaceous debris that has been produced during the synthesis of graphene oxide by the chemical exfoliation of graphite and still remain on graphene sheets through the chemical reduction steps. Interestingly, the presence of the carbonaceous debris causes a significant impact on the electrochemical behavior of the chemical reduced graphene. Herein, we demonstrate that the electrocatalytical activities of the graphene are greatly boosted by the adhered carbonaceous debris. After the removal of the carbonaceous debris, the electrocatalysis of graphene is not superior to conventional graphite.     

Single-layered graphene oxide nanosheet/polyaniline hybrids fabricated through direct molecular exfoliation

In this study, we used direct molecular exfoliation for the rapid, facile, large-scale fabrication of single-layered graphene oxide nanosheets (GOSs). Using macromolecular polyaniline (PANI) as a layered space enlarger, we readily and rapidly synthesized individual GOSs at room temperature through the in situ polymerization of aniline on the 2D GOS platform. The chemically modified GOS platelets formed unique 2D-layered GOS/PANI hybrids, with the PANI nanorods embedded between the GO interlayers and extended over the GO surface. X-ray diffraction revealed that intergallery expansion occurred in the GO basal spacing after the PANI nanorods had anchored and grown onto the surface of the GO layer. Transparent folding GOSs were, therefore, observed in transmission electron microscopy images. GOS/PANI nanohybrids possessing high conductivities and large work functions have the potential for application as electrode materials in optoelectronic devices. Our dispersion/exfoliation methodology is a facile means of preparing individual GOS platelets with high throughput, potentially expanding the applicability of nanographene oxide materials.     

Synthesis of polystyrene nanoparticles “armoured” with nanodimensional graphene oxide sheets by miniemulsion polymerization

Polystyrene particles “armoured” with nanosized graphene oxide (GO) sheets have been prepared by aqueous miniemulsion polymerization of styrene, exploiting the amphiphilic properties of GO in the absence of conventional surfactants. The nanoscale GO sheets were prepared from graphite nanofibers of diameter approximately 100 nm based on a novel procedure, thus effectively ensuring the absence of larger sheets. Polymerization proceeded to high conversion with minor coagulation, with final number‐average particle diameters of approximately 500 nm, but relatively broad particle size distributions. Scanning electron microscopy analysis revealed particles with a textured surface, consistent with the expected morphology. Interestingly, analysis of GO sheets recovered from the polymerization revealed that the GO sheets are partially reduced during the polymerization—approximately 50% of the initial carboxyl groups of the GO were lost, consistent with some loss in colloidal stability at high conversion. The overall approach offers a convenient and attractive synthetic route to novel graphene‐based polymeric nanostructures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Preparation of chloro-functionalized reduced graphene oxide by silver-catalyzed radical reaction

It is well-known that chemical functionalization of graphene has the great significance.We report the development of a new synthesis method of chloro-functionalized reduced graphene oxide(rGOCl).The rGOCl was prepared by radical reaction,and treatment of carboxyl graphene oxide(GOCOOH) with N-chlorosuccinimide(NCS) at 90℃ for 10 h under an atmosphere of nitrogen,using silver nitrate as catalyst.The morphologies and structures of the prepared materials were investigated by field-emission scanning electron microscopy(FESEM),X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR),Raman spectroscopy and the thermal gravimetric.Results indicated that the rGOCl can be readily obtained from graphene oxide(GO) in three steps.