Ru/Al2O3-catalyzed transfer dehydrogenation of alcohols

Summary Primary and secondary alcohols were oxidized to their corresponding aldehydes or ketones in good yields using Ru/Al₂O₃ as catalyst in the presence of acetone. The catalyst can be recovered by simple filtration and reused after washing with acetone.     

Room temperature Fe(NO3)3·9H2O/TEMPO/NaCl-catalyzed aerobic oxidation of homopropargylic alcohols

A practical and eco-friendly aerobic oxidation of homopropargylic alcohols using Fe(NO₃)₃·9H₂O/TEMPO/NaCl as catalysts at room temperature under atmospheric pressure was developed affording corresponding homopropargylic ketones with moderate to good yields. Aryl, heteroaryl as well as alkyl 1,2-allenic ketones were obtained by the isomerization of corresponding terminal homopropargylic ketones through column chromatographic workup on silica gel.     

KF/Al2O3 and PEG-400 as a recyclable medium for the selective α-selenation of aldehydes and ketones. Preparation of potential antimicrobial agents

2-Phenylseleno aldehydes and ketones were selectively obtained using solid-supported catalyst (KF/Al₂O₃) and PEG-400 as clean, recyclable medium in good to excellent yields. The method was applied in the preparation of highly functionalized 2-phenylseleno citronellal and citronellol, potential bactericide agents. The catalytic system KF/Al₂O₃ and PEG-400 can be re-used for four times without previous treatment.     

Preparation of Al2O3-supported nano-Cu2O catalysts for the oxidative treatment of industrial wastewater

Cuprous oxide (Cu₂O) nanoparticles supported on Al₂O₃ prepared using two different methods (hereafter referred to as catalyst I and II, respectively) were characterized by XRD and TEM. The catalytic activities of catalyst I and II during the treatment of industrial wastewater were then investigated. Specifically, the progress of the catalytic oxidation of industrial wastewater was observed by monitoring the time-dependent change in the chemical oxygen demand (COD) of industrial wastewater when the catalysts were applied. The results indicated that the catalytic activity of catalyst II was greater than that of catalyst I. Furthermore, under optimal conditions the COD removal efficiency was 94.59%. Finally, the mechanism by which the oxidative degradation of the industrial wastewater occurred could be explained based on a hydroxyl radical mechanism.     

Selective Catalytic Reduction of NO with Propene over Au/Fe2O3/Al2O3 Catalysts

A series of Au/Fe₂O₃/Al₂O₃ catalysts were prepared by the homogeneous deposition-precipitation method. The catalytic activity of the catalyst samples for selective catalytic reduction of NO by propene under oxygen-rich atmosphere was evaluated. The results showed that 2%Au/10%Fe₂O₃/Al₂O₃ exhibited good low-temperature activity. The maximum of NO conversion reached 43% at 300 °C, while it was only 21% over the 2%Au/Al₂O₃ catalyst at the same temperature. The addition of 2% steam to the feed gas had little effect on the catalytic activity. X-ray diffraction results indicated that both Au and Fe₂O₃ particles were highly dispersed over Al₂O₃. H₂-temperature-programmed reduction results indicated that there was strong interaction between Au and Fe₂O₃, which made the reduction of Fe₂O₃ easy. The synergistic effect between Au and Fe₂O₃ was probably responsible for the good catalytic performance of the Au/Fe₂O₃/Al₂O₃ catalyst at low temperature.     

A mild and efficient acetylation of alcohols, phenols and amines with acetic anhydride using La(NO3)3·6H2O as a catalyst under solvent-free conditions

A wide variety of alcohols, phenols and amines are efficiently and selectively converted into the corresponding acetates by treatment with acetic anhydride in the presence of catalytic amounts of La(NO₃)₃·6H₂O under solvent-free conditions at room temperature. The method is compatible with acid sensitive hydroxyl protecting groups such as TBDMS, THP, OBz, OBn, Boc and some isopropylidenes and offers excellent yields of the mono acetates of 1,3-, 1,4- and 1,5-diols.     

Photocatalytic oxidation of primary and secondary benzylic alcohols to carbonyl compounds catalyzed by H3PW12O40/SiO2 under an O2 atmosphere

An efficient, selective and green procedure for the photocatalytic oxidation of primary and secondary benzylic alcohols to the corresponding aldehydes and ketones has been achieved using silica-encapsulated H₃PW₁₂O₄₀ as a recyclable heterogeneous photocatalyst in acetonitrile under oxygen gas as the sole reoxidant of the catalyst.     

Kinetics of catalytic combustion in air over Pt/Al2O3/Al catalyst

Summary Catalytic combustion of toluene, propylene and CO over Pt/Al₂O₃ /Al catalyst was investigated. Strong inhibition effects are observed when the mixture of toluene, propylene and CO is oxidized. A reaction mechanism of catalytic combustion over Pt/Al₂O/Al is proposed. The results from kinetic models are in good agreement with the experimental data.     

Chemoselective sulfoxidation by H2O2 or HNO3 using a phosphate impregnated titania catalyst

A variety of organosulfur compounds have been selectively oxidized to the corresponding sulfoxides by either H₂O₂ or HNO₃ using a newly developed solid acid catalyst composed of 84.5% of TiO₂ and 15.5% of [Ti₄H₁₁(PO₄)₉]·nH₂O (n = 1-4). The chemoselective oxidation of sulfides in the presence of vulnerable groups such as -CN, -CC-, -CHO, or -OH, as well as sulfoxidation of substrates like benzothiazole, glycosyl sulfide, and dibenzothiophenes is some of the important attribute of the protocol. Nitric acid, under the present experimental conditions, brings about relatively better selectivity than hydrogen peroxide.     

PyHBr3/TBN/H2O as catalytic system for the oxidation of sulfides to sulfoxides with air as the oxidant

Pyridinium bromide perbromide (PyHBr₃) and tert-butyl nitrite (TBN) catalytic system was used for the oxidation of sulfides with air as the oxidant. Under mild conditions (at room temperature), a series of sulfide substrates have been oxidized to their corresponding sulfoxides with high conversion rate. To the best of our knowledge, for the first time, the PyHBr₃/TBN/H₂O is reported as exceptional catalyst system for the oxidation discussed in this Letter.     

Synthesis of vinyl sulfides via hydrothiolation of alkynes using Al2O3/KF under solvent-free conditions

We present here a clean, solvent-free hydrothiolation of alkynes using solid supported catalyst (Al₂O₃/KF). This efficient and improved method selectively furnishes the corresponding anti-Markovnikov vinyl sulfides in good to excellent yields. The method is applicable for aliphatic and aromatic thiols and the catalytic system can be re-used up to two times without previous treatment and with comparable activity.     

Preparation of MoO3/g-Al2O3 catalyst by the reaction of a-boehmite with MoO3/H2O slurry - dual role of MoO3 as active phase and texture stabilizer during calcination

Summary Catalyst MoO₃/g-Al₂O₃ was prepared by the reaction of a-boehmite with molybdic acid in slurry MoO₃/H₂O followed by calcination. The deposited MoO₃ functioned as thermal stabilizer and inhibited sintering of Al₂O₃ phase during calcination. After calcination at 550 and 650^oC the surface area of Al₂O₃ obtained from a-boehmite was 207 and 172 m² g^-1, respectively, and of MoO₃/Al₂O₃ obtained from MoO₃/a-boehmite was 323 and 285 m² g^-1, respectively. On the other hand, molybdic acid did not work as peptization agent and the mechanical strength of MoO₃/Al₂O₃ was not higher than of Al₂O₃. The catalyst was sulfided and its activity in thiophene hydrodesulfurization was tested; it exhibited about the same activity as reference industrial MoO₃/Al₂O₃ catalyst.     

Solvent-free catalytic preparation of 1,1-diacetates from aldehydes using a Wells-Dawson acid (H6P2W18O62·24H2O)

Aromatic and aliphatic aldehydes are transformed in 1,1-diacetates (acylals) in mild conditions, by a treatment with acetic anhydride and a Wells-Dawson acid (H₆P₂W₁₈O₆₂·24H₂O). gem-Diacetylation proceeds in Ac₂O with a little as 1% mol Wells-Dawson acid at room temperature and under solventless conditions, obtaining very good to excellent yields (88-98%) of 1,1-diacetates (19 examples). Neither 4-dimethylaminobenzaldehyde nor ketones react under the same conditions.     

Synthesis of (Z)-organylthioenynes using KF/Al2O3/solvent as recyclable system

PEG-400 and glycerol were successfully used as recyclable solvents for the synthesis of several organylthioenynes in good to excellent yields and high selectivity using solid supported catalyst (KF/Al₂O₃). This easy, general and improved method furnishes the corresponding alkenyl sulfides preferentially with Z configuration. The catalytic system and the glycerol or PEG-400 can be reused up to three times without previous treatment with comparable activity.     

Effect of LaFeO3 Decoration and Ozone Treatment on Thermal Stability of Au/Al2O3 for CO Oxidation

The 1.1%Au/LaFeO_x/Al₂O₃ catalysts were prepared by the iso-volume impregnation method and activated with H₂ or O₃. The catalytic performance for CO oxidation at room temperature was investigated by accelerated deactivation tests in 1.0% CO reactant stream at 550 °C. The introduction of La and Fe enhanced the thermal stability of Au/Al₂O₃ with a decrease in initial activity, probably due to the formation of LaFeO₃ perovskite on the Al₂O₃ surface. The 1.1%Au/2%LaFeO₃/Al₂O₃ catalyst activated by H₂ can transform 65% CO into CO₂ at room temperature after pretreatment in 1.0% CO reactant stream at 550 °C for 2 h, whereas 1.1%Au/Al₂O₃ activated by H₂ totally loses its activity. O₃ activation can always make 1.1%Au/LaFeO₃/Al₂O₃ more active than that of H₂ activation during the pretreatment process in 1.0% CO. After pretreatment for 10 h, 1.1%Au/2%LaFeO₃/Al₂O₃ activated by O₃ still shows 40% conversion of 1.0% CO at room temperature, whereas those activated by H₂ become inactive completely. The better thermal stability of the catalysts activated by O₃ may be due to that O₃ activation leads to the formation of partially oxidized state of Au in Au/FLA-O₃, which may reinforce the interaction between the metal and support.     

Highly efficient oxidation of alcohols by the system "hydrogen peroxide-[lmn(o)3mnl](pf6)2 (l = 1,4,7-trimethyl-1,4,7-triazacyclononane)-oxalic acid"

Summary The dinuclear manganese(IV) complex [LMn(O)₃MnL](PF₆)₂ (1, L = 1,4,7-trimethyl-1,4,7-triazacyclononane) catalyzes the extremely efficient oxidation of alcohols with hydrogen peroxide at room temperature. Oxalic acid is an obligatory co-catalyst. The oxidation of isopropanol, for example, yields acetone with turnover numbers up to 40000 after 5-10 h in the absence of a solvent. 2-Cyanoethanol was oxidized by this system with somewhat lower efficiency (conversion 70%). The catalytically active cation from salt 1 was obtained in an insoluble form containing a heteropoly anion [Mn₂O₃(TMTACN)₂]₂[SiW₁₂O₄₀]. Oxidation of 2-cyanoethanol using this heterogenized catalyst and oxalic acid gave the oxo-products with the 54% total yield.     

Synthesis of novel organoselenium as catalyst for Baeyer-Villiger oxidation with 30% H2O2

A novel diselenide was synthesized in good yield via only four steps from phenol, and was employed as the catalyst for the Baeyer-Villiger oxidation with 30% H₂O₂ to obtain lactones in good yields.     

采用溶胶-凝胶-溶剂热路径合成H3PW12O40/TiO2和H4SiW12O40/TiO2 及其光催化降解二硝基甲苯

以非离子表面活性剂P123为结构导向剂,采用溶胶-凝胶与溶解热相结合方法,制备了两类介孔材料H₃PW₁₂O₄₀/TiO₂和H₄SiW₁₂O₄₀/TiO₂,并对其进行了表征.?X射线粉末衍射和拉曼光谱分析表明,所制催化剂为锐钛矿晶型,体系中H₃PW₁₂O₄₀和H₄SiW₁₂O₄₀的Keggin结构经400?℃焙烧后仍保持完整.?H₃PW₁₂O₄₀/TiO₂和H₄SiW₁₂O₄₀/TiO₂的平均粒径分别为15.49和7.75?nm.?N₂吸附-脱附和扫描电镜结果表明,P123的加入使催化剂的粒径减小,比表面积和孔体积明显增大,其中H₃PW₁₂O₄₀/TiO₂和H₄SiW₁₂O₄₀/TiO₂的比表面积分别高达252.2和250.0?m²/g.?紫外漫反射吸收光谱表明,与纯TiO₂相比,复合催化剂的吸收光谱发生了明显的红移,且吸收强度明显增大.?催化剂对DNT降解实验表明,在最佳操作条件下降解率可高达95%.?     

Synthesis, structural characterization and properties of a 3D infinitely extended structural rare earth coordination compound of K3{[Sm(H2O)7]2Na[α-SiW11O39Sm(H2O)4]2} · 14 H2O· 14 H2O

A 3D infinitely extended structural rare earth coordination compound with a formula of K₃{[Sm(H₂O)₇]₂Na[α-SiW₁₁O₃₉Sm(H₂O)₄]₂}·14H₂O has been synthesized by reaction of Sm₂O₃, HClO₄, NaOH with α-K₈SiW₁₁O39·nH₂O, and characterized by IR, UV spectra, ICP, TG-DTA, cyclic voltammetry, variable-temperature magnetic susceptibility and X-ray single-crystal diffraction. X-ray single-crystal diffraction indicates that the title compound crystallizes in a triclinic lattice, Pī space group, with a = 1.2462(3) nm, b = 1.2652(3) nm, c = 1.8420(4) nm, α = 87.45(3)°, β = 79.91(3)°, γ= 82.57(3)°, Z = 1, R₁ = 0.0778, wR₂ = 0.1610. Structural analysis reveals that Sm³⁺(1) coordination cation has incorporated into the vacant site of [α-SiW11O₃₉]⁸⁻ entity, forming the [α- SiW₁₁O₃₉Sm(H₂O)₄]⁵⁻ subunit. The two adjacent [α-SiW₁₁O₃9Sm(H₂O)4]⁵⁻ subunits are combined with each other through two Sm(1)-O-W bridges accompanying the formation of dimmer structural unit [α-SiW₁₁O₃₉Sm(H₂O)₄]₂ ¹⁰⁻ of the title compound. The neighboring dimmer structural units [α-SiW₁₁O₃₉Sm(H₂O)₄]₂ ¹⁰⁻ are linked to form the 1D chainlike structure by means of two Sm³⁺(2) and a Na⁺(1) coordination cations. The K⁺(1) cations connect the 1D packing chains constructing the 2D netlike structure, and adjacent netlike layers are also grafted by K⁺(2) cations to build the novel 3D infinitely extended structure. The result of TG-DTA curves manifests that the decomposition temperature of the title polyanionic framework is 554°C. The cyclic voltammetry measurements show that the title polyanion has the two-step redox processes in aqueous solution with pH = 3.1. Variable temperature magnetic susceptibility indicates the title compound obeys the Cruie-Weiss Law in the higher temperature range from 110 to 300 K, while in the lower temperature range from 2 to 110 K the comparatively strong antiferromagnetism interactions can be observed.     

Pt/MOx(M=Ni,Fe,Co,Ce)催化剂上CO氧化反应中抗H2O与CO2的性能研究

我们研究了4种负载型Pt催化剂（1Pt/NiO、1Pt/FeO_x、1Pt/Co₃O₄和Pt/CeO₂）上不同反应条件下CO氧化活性及抗H₂O和CO₂性能.发现反应气氛中CO₂的加入与CO形成了竞争吸附,并在催化剂表面形成了碳酸盐物种堵塞了活性位,从而导致催化剂失活.反应气氛中H₂O的加入对1Pt/CeO₂催化剂的活性有所抑制,但对1Pt/FeO_x、1Pt/NiO和1Pt/Co₃O₄催化剂的活性却有促进作用.在1Pt/FeO_x和1Pt/CeO₂催化剂上的分步反应实验和动力学研究表明,尽管H₂O的加入在两种催化剂上均与CO形成了竞争吸附,但在1Pt/FeO_x催化剂上H₂O在载体表面解离形成的羟基更易与CO反应,开辟了新的反应途径,从而提高了反应性能.此外,H₂O的加入能有效分解该催化剂上的碳酸盐物种,从而保持了其稳定性.