Metal chelates in adsorption polarography I: Mo(VI) and derivatives of oxine

The formation of complexes between Mo(VI) and 8-hydroxy-quinoline (oxine) and four oxine derivatives were investigated by multiwavelength molecular absorption spectrometry, potentiometry, and polarography. The following pK_OH- and pK_NH- values of the ligands and logK ₂₁₁-values of the complexes MoO₂(OH)₂L ^x– (x=1 or 2) were obtained at 25° C and an ionic strength of 1M(NaClO₄): 5,7-dinitro8-hydroxyquinoline 4.59, <0, 14.50; 7-nitro-8-hydroxyquinoline-5-sulfonic acid 5.34, 0.41, 15.70; 7-iodo-8-hydroxyquinoline-5-sulfonic acid 6.98, 2.62, 17.65; 8-hydroxyquinoline-5-sulfonic acid 8.33, 4.13, 18.71; and 8-hydroxyquinoline 9.62, 5.28, 19.69. A good linearity was found between logK ₂₁₁ and the sum of the pK-values of the OH- and NH⁺-groups. The dependence of the peak current of Mo(VI)-determinations by adsorption polarography of the 7-nitro-8-hydroxyquinoline-5-sulfonate complex of Mo(VI) MoO(OH)₃L^– can quantitatively be described at pH 0.8–2 using the corresponding pK-values and the log K₃₁₁ of 18.54±0.03, determined by polarography.     

Trace analysis of vanadium as pentavalent vanadium using differential pulse polarography with a coupled catalytic homogeneous reaction

The differential pulse polarographic determination of the vanadium (V) ion coupled with a catalytic homogeneous reaction was carried out in a system containing the vanadium (V)-PAR complex and an oxidant in acetic/acetate buffer. On addition of the powerful oxidant, sodium bromate, the peak current for the reduction of the vanadium (V) complex was increased significantly by about 21 times. A calibration plot was found to be linear in the concentration range 0.05–0.25 g/ml and the detection limit was 5 ng/ml.     

Determination of tungsten and tin ions after preconcentration by flotation

A highly sensitive and selective combined method of flotation followed by spectrophotometry/d.c. polarography for the determination of tungsten and tin ions in acid and alkaline waste waters and hydrometallurgical solutions is presented here. Both kinds of ions are coprecipitated in the analyte solution with zirconium hydroxide after addition of ZrOCl₂ solution and ammonia. Afterwards, the collector precipitate is separated from the aqueous phase and preconcentrated by flotation for which sodium oleate and a frother are added. The precipitate is dissolved in a small amount of acid, with the organic reagents being destroyed by oxidation. The enrichment factor of the proposed technique is 100, with variations possible. Recovery is 94% for tungsten and 99% for tin. Spectrophotometry of the thiocyanate complex and d.c. polarography are applied as determination techniques for tungsten and tin, respectively. Detection limits attainable by this technique are 6 ng · ml^–1 for tungsten and 5 ng · ml^–1 for tin for the initial sample.     

Kinetic-spectrophotometric determination of molybdenum (VI) and tungsten (VI) in mixtures

A simple kinetic-spectrophotometric method is described for the determination of molybdenum(VI) and tungsten(VI) in mixtures, without prior separation. The method is based on the catalytic effect of molybdenum(VI) and tungsten(VI) on the oxidation of 2,4-diaminophenol dihydrochloride (DAP) by hydrogen peroxide in acidic medium. The reaction was followed spectrophotometrically by measuring the rate of change in absorbance with time at 500 nm. A partial inhibition in the catalytic activity of each catalyst, when the other one is present, at all ratios of Mo(VI) W(VI) mixtures studied was observed. On the other hand, the catalytic activity of tungsten(VI) dropped to zero whilst that of molybdenum(VI) decreased slightly, in the presence of citrate ions. Two sets of experiments were carried out, the first in the absence and the other in the presence of citrate, and the resolution of Mo(VI)/W(VI) mixtures was achieved by solving two simultaneous equations. Various molar ratios of Mo(VI) W(VI), at the 10^–6 M level, from 0.2 1 to 5 1 can be determined with satisfactory precision and accuracy. The selectivity of the method was investigated and the method was applied successfully to the determination of molybdenum and tungsten in each other's presence in steel.     

Trace analysis of toxic metals,III. Determination of chromium as trivalent chromium by differential pulse polarography

Methods for trace analysis of chromium as Cr³⁺ were investigated, using differential pulse polarography in various media. Determination at the ng/ml-g/ml range can be carried out in KCl/HCl, KCNS/HOAc, and other media. Total concentration of chromium in a solution containing Cr³⁺ and HCrO ₄ ^– can be determined in KCNS/HOAc, and it is found that HCrO ₄ ^– can be converted quantitatively to Cr³⁺. The relative quantity of HCrO ₄ ^– and Cr³⁺ can be determined by the difference between the total chromium concentration and the concentration of HCrO ₄ ^– . The sensitivity (12.5 ng/ml) and accuracy of this method is better than the method that determines total chromium as HCrO ₄ ^– .     

Asymmetric epoxidation of cis-1-propenylphosphonic acid (CPPA) catalyzed by chiral tungsten(VI) and molybdenum(VI) complexes

In the presence of 5.0 mol% chiral tungsten(VI) and molybdenum(VI) complexes, the catalytic asymmetric epoxidation of cis-1-propenylphosphonic acid (CPPA) with 30% aqueous H₂O₂ affording (1R,2S)-(−)-(1, 2)-epoxypropyl phosphonic acid (fosfomycin) was first described. The enantioselectivities of the tungsten and molybdenum catalysts depend strongly on the ligands, reaction temperature and solvent. In CH₂Cl₂ at 0 °C for 72 h, complex MoO₂[(+)-campy]₂ catalyzed the asymmetric epoxidation in a 100% conversion of CPPA with the highest 80% ee. The mechanism of the present epoxidation could be described as direct oxygen transfer occurred on the interface of the biphasic H₂O-nonprotic system.     

含钨化合物催化合成己二酸研究进展

己二酸是工业上具有重要应用的二元羧酸,其合成方法的研究受到了广泛的关注.其传统的合成方法对环境造成了极大的破坏.利用含钨化合物作为催化剂催化合成己二酸是一种绿色环保的新方法,引起了人们的重视.作者介绍了近年来含钨化合物催化合成己二酸的研究进展,分析比较了不同催化剂体系的研究情况,展望了今后己二酸合成的发展前景.     

Application of a ternary complex of tungsten(VI) with 4-nitrocatechol and thiazolyl blue for extraction-spectrophotometric determination of tungsten

A new ternary ion-association complex of tungsten(VI), 4-nitrocatechol (NC), and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (Thiazolyl Blue, MTT) was obtained and studied using an extraction-spectrophotometric method. The optimum pH, reagent concentrations, and extraction time were determined. The composition of the complex was found to be W(VI): NC: MTT = 1: 2: 2. The extraction process was investigated quantitatively and the key constants were calculated. The molar absorptivity of the chloroform extract at λ_max = 415 nm was 2.8 × 10⁴ dm³ mol⁻¹ cm⁻¹, and the Beer’s law was obeyed up to 8.8 μg cm⁻³ tungsten(IV). The limit of detection and limit of quantification were calculated to be 0.27 μg cm⁻³ and 0.92 μg cm⁻³, respectively. The effect of foreign ions and reagents was studied and a competitive method for determination of tungsten in products from ferrous metallurgy was developed. The residual standard deviation and the relative error were 0.53 % and 0.2 %, respectively.     

单扫描示波极谱法测定扑热息痛

扑热息痛与NaNO2在中性介质中发生反应，其亚硝化衍生物具有良好的电活性。在pH9．37的Britton-Robinson缓冲溶液中，于-0．56V(vs．SCE)产生灵敏的极谱还原峰，峰电流与扑热息痛质量浓度在0．007-0．4mg/L范围有良好的线性关系，检测下限为5μg/L。此法已用于测定小儿速效感冒灵。     

High performance ultra trace analysis in molybdenum and tungsten accomplished by on-line coupling of ion chromatography with simultaneous ICP-AES

For the characterisation of trace elements in high purity Mo and W analytical methods with a detection limit in the ng/g-range have to be used. Today mass spectrometric methods are state of the art for such applications. However, these methods in case of refractory metal analysis are time consuming, expensive, limited by isobaric interferences and therefore not very suitable for quality control in an industrial laboratory. With respect to these drawbacks a cost and time efficient method was developed by on-line coupling of an ion chromatographie system to a simultaneous ICP-AES (Inductively Coupled Plasma — Atomic Emission Spectrometry) instrument. Within the limitations caused by the hard- and software of the system all parameters such as eluent concentration and flow rate, nebulizer and plasma gas flow, sampling frequency, integration time and the number of simultaneously measured emission lines were optimised. Further enhancement of the sensitivity was achieved by the use of an ultrasonic nebulizer pushing the detection limits down to the pg/g- and ng/g-range for 22 representative elements.Dedicated to Professor Dr. rer. nat. Dr. h. c. Hubertus Nickel on the occasion of his 65th birthday     

Determination of nisoldipine in film tablets by differential pulse polarography

Summary A differential pulse polarographic (DPP) method was developed for the determination of nisoldipine in Baymycard^® film tablets without interference from excipients. Nisoldipine is reduced at the dropping mercury electrode in a single, irreversible peak. Linearity between the nisoldipine concentration and the peak height was observed in the 5·10^–4–10^–7 M concentration range. The detection limit is 22 ng/ml. The analysis of a series of 10 Baymycard^® 5 mg film tablets showed a standard deviation of ±0.115 mg and aS _rel of ±2.30%, respectively.

---

Gehaltsbestimmung von Nisoldipin in Filmtabletten mittels differentieller Pulspolarographie

Zusammenfassung Eine Bestimmung von Nisoldipin in Baymycard^® Filmtabletten mittels differentieller Pulspolarographie (DPP) wurde entwickelt, die keine Störungen durch Tablettenhilfsstoffe aufweist. Nisoldipin wird an der tropfenden Quecksilberelektrode in einem einzigen, irreversiblen Peak reduziert. Linearität zwischen Nisoldipinkonzentration und Peakhöhe wurde im Konzentrationsbereich von 5·10^–4–10^–7 M festgestellt. Die Bestimmungsgrenze beträgt 22 ng/ml. Die Analyse einer Serie von 10 Baymycard^® 5 mg Filmtabletten ergab eine Standardabweichung von ±0.115 mg, dies entspricht einerS _rel von ±2.30%.

     

Cathode ray polarography and differential pulse polarography of the catalytic molybdenum(VI) wave

The optimum conditions of electrolyte composition and pH were studied for the cathode ray polarography (c.r.p.) of the catalytic molybdenum(VI) wave; 1–2 M potassium nitrate at pH 1.6–2.2 is optimum, the detection limit is 3 × 10^-9 M (0.3 ppb) molybdenum(VI). Equal molar concentrations of foreign electroactive substances do not interfere at the potential of the molybdenum wave and 500-fold amounts of these can be tolerated if their c.r.p. peaks are separated from the molybdenum wave by 0.1 or 0.2 V. Similar conditions were used for the differential pulse polarography of the catalytic wave. The detection limit is 2 × 10^-8 M (2 ppb). being limited in part by lead impurities which contribute to the background.     

Differential polarography of copper(II) complex

A differential polarographic study has been carried out on the interaction product formed in the interaction of copper(II) with bis(2-hydroxymethyl-5-hydroxy-4-pyrone-6)ketone. The data obtained using the differential pulse method show that copper(II) exhibits a coordination number of one and a reproducible formation constant that is fairly consistent over a moderate concentration range.     

Determination of acipimox in capsules by differential pulse polarography

A differential pulse polarographic (DPP) method has been developed for the determination of acipimox in its pharmaceutical formulations. Using Sörensen buffer pH 6.0 as supporting electrolyte a single, irreversible peak occurred at –0.79 V vs an Ag/AgCl reference electrode. The peak height vs concentration plot was found to be linear over the range of 10^–6 to 6 × 10^–4 mol/l. The detection limit is 60ng/ml. The analysis of a series of 10 Olbetam® 250 mg capsules showed an overall standard deviation of ± 4.18 mg and a S_rel of ± 1.66%, respectively.     

Multi-element trace analysis of tungsten

Investigations carried out in order to determine traces of 25 elements in tungsten in the lower g/g range are reported on. Atomic absorption spectrometry and plasma atomic emission spectrometry as well as solution photometry and activation analysis were the main techniques used.     

A Spectrophotometric Study of the Molybdenum(VI)-1-Pyrrolidinecarbodithioate System

Abstract

A spectrophotometric study of the molybdenum-1-pyrrolidinecarbodithioate complex has shown that the meta1:ligand ratio is 1;2. Both molybdenum(VI) and molybdenum(V) form complexes with almost identical absorption spectra. The conditional extraction constant for the molybdenum(VI)-1-pyrrolidinecarbodithioate in chloroform system has been evaluated as 6.3 × 10¹⁶.     

Determination of Cr(VI) by portable tungsten coil electrothermal atomic absorption spectrometer after surfactant-assisted dispersive liquid-liquid microextraction

As a new developed instrument, a portable tungsten coil electrothermal atomic absorption spectrometer (W-coil ET-AAS) was first coupled with surfactant assisted dispersive liquid–liquid microextraction (SA-DLLME) to improve its analytical performance and expand its applications in this work. SA-DLLME was very simple, rapid and the extraction efficiency was considerably improved by the effect of surfactant, which was suitable to be coupled with the portable instrument in field analysis. After SA-DLLME, concentrated chromium in organic phase was directly determined on W-coil atomiser. The influence factors relevant to SA-DLLME and instrumental conditions were studied systematically. Under the optimal conditions, the limit of detection (LOD) for Cr(VI) was 0.016 µg L^?1, with sensitivity enhancement factor (EF) of 107. The relative standard deviation (RSD) for seven replicate measurements of 0.5 µg L^?1 of Cr(VI) was 4.6%. The recoveries for the spiked samples were in the acceptable range of 96.8–104%. The rapid, simple and high effective method greatly improved the sensitivity of this portable spectrometer for the determination of Cr(VI) and was applied to the analysis of ultra-trace Cr(VI) in real and certified water samples with satisfactory results.