Pulsed laser deposition of NdNiO3 thin films

We report the structural and transport properties of NdNiO₃ thin films prepared via pulsed laser deposition over various substrates. The films were well textured and c-axis oriented with good crystalline properties. The electrical resistivity of the films undergoes a metal-insulator transition, depending on the deposition process. Well-defined first order metal-insulator phase transition (T_MI) was observed in the best quality films without high pressure processing. Various growth conditions such as substrate temperature, oxygen pressure and thickness were varied to see their influence on T_MI. Deposition temperature was found to have a great impact on the electrical and structural properties of these films. Further the films deposited on LaAlO₃ substrate were found to be highly oriented with uniform grain size as observed from X-ray diffraction and atomic force microscopy, whereas those on Si substrate were polycrystalline, dense and randomly oriented.     

Transmission electron microscopy study of epitaxial La0.8MnO3 thin films on SrTiO3

The structure and microstructure of La_0.8MnO₃ thin films on SrTiO₃ substrates, fabricated by pulsed laser deposition at substrate temperatures of 873?K and 1073?K, have been studied by transmission electron microscopy. In both films, columnar growth morphology has been observed. The columnar grain size is found to increase with increasing substrate temperature. In the film deposited at a substrate temperature of 1073?K, there is only one rhombohedral phase. However, two phases, a rhombohedral one and an orthorhombic one, have been observed in the film deposited at 873?K.     

Deposition of quasi-crystal Al-doped ZnO thin films for photovoltaic device applications

Quasi-crystal aluminum-doped zinc oxide (AZO) films were prepared by in situ radio frequency (RF) magnetron sputtering (sputtering without annealing) on glass substrates. The influence of deposition parameters on the optoelectronic and structural properties of the in situ deposited quasi-crystal AZO films was investigated in order to compare resulting samples. X-ray diffraction (XRD) patterns show that the quasi-crystal AZO thin films have excellent crystallization improved with increase of the RF power and substrate temperature, with an extremely preferential c-axis orientation exhibit sharp and narrow XRD pattern similar to that of single-crystal. Field emission scanning electron microscopy (FESEM) images show that quasi-crystal AZO thin films have uniform grains and the grain size increase with the increase of RF power and substrate temperature. Craters of irregular size with the columnar structure are observed in the quasi-crystal AZO thin films at a lower substrate temperature while many spherical shaped grains appeared at a higher substrate temperature. The average optical transmittance of all the quasi-crystal AZO films was over 85% in the 400-800 nm wavelength range. The resistivity of 4.176 × 10⁻⁴ Ω cm with the grain size of 76.4891 nm was obtained in the quasi-crystal AZO thin film deposited at 300 °C, under sputtering power of 140 W.     

Effect of phase stratification into electro- and magnetotransport in heteroepitaxial La2/3Ca1/3MnO3 films

The La_2/3Ca_1/3MnO₃ films 25-nm thick biaxially compressed in the substrate plane, grown quasi-coherently on the (001) surface of the LaAlO₃ single crystal, were studied using laser vaporization. It was found that mechanical stresses acting during nucleation and growth promoted calcium enrichment of the cation sublattice of the manganite layer, which caused a decrease in its unit cell volume. Crystalline grains in manganite films were distinctly oriented along the normal to the substrate plane; the grain size in the substrate plane was within 20–40 nm, and the relative grain misorientation in the substrate plane did not exceed 0.2°. In zero magnetic field, the maximum in the temperature dependence of the resistivity ρ of La_2/3Ca_1/3MnO₃ films was observed at temperatures close to 210 K. At T < 100 K and μ₀ H = 2 T, the magnetoresistance of manganite films was negative, weakly depended on temperature, its value was about–0.45. The magnetic field caused transformation of nonferromagnetic phase inclusions to ferromagnetic ones, which resulted in a decrease in the La_2/3Ca_1/3MnO₃ film resistivity with increasing magnetic field. At low temperatures (T < 100 K), a hysteresis was observed in the dependences of the film resistivity on the magnetic field.     

衬底温度对MOCVD法沉积ZnO透明导电薄膜的影响

研究了衬底温度对MOCVD技术制备的ZnO薄膜的微观结构和光电特性影响. XRD和SEM的研究结果表明，衬底温度对ZnO薄膜的微观结构有显著影响，明显的形貌转变温度大约发生在175℃，低于175℃，薄膜呈镜面结构，晶粒为球状，高于177℃的较高温度范围，薄膜从“类金字塔”状的绒面结构演化为“岩石”状显微组织；随着温度增加，薄膜的晶粒尺寸明显增大.绒面结构的未掺杂ZnO薄膜具有17.96 cm²/V·s的高迁移率和3.28×10^-2 Ω·cm的低电阻率，对ZnO薄膜的进一步掺杂和结构优化有望应用于Si薄膜太阳电池的前电极. 关键词： MOCVD ZnO薄膜 透明导电氧化物 太阳电池     

基片温度对SiNx薄膜结晶状态及机械性能的影响

利用微波电子回旋共振增强磁控反应溅射法在不同基片温度下制备无氢SiN_x薄膜.通过傅里叶变换红外光谱、透射电子显微镜、台阶仪、纳米硬度仪等表征技术,研究了基片温度对SiN_x薄膜结晶状态、晶粒尺寸、晶体取向等结晶性能以及薄膜的生长速率、硬度等机械性能的影响,并探讨了薄膜结晶性能与机械性能之间的关系.研究结果表明,在基片温度低于300℃时制备的SiN_x薄膜以非晶状态存在,硬度值仅为18GPa左右;基片温度 关键词： x')" href="#">SiN_x 磁控溅射 微观结构 硬度     

Characterization of flash evaporated Hg1−xZnxTe films

Results of structural, optical and electrical properties of flash-evaporated Hg_1−xZn_xTe films. in the composition range 0.08 ⩽ x ⩽ 1, show that the films are formed by alloying HgTe and ZnTe. The optical band gap of these films increases from 0.04 to 2.26 eV with an increase in Zn concentration from 0.08 to 1.0. The band gap variation is not linear but shows a “bowing effect” familiar to pseudobinary solid solutions. An increase in resistivity with an increase in the substrate temperature can be related to larger grain size at the higher substrate temperatures in these p-type films. The films exhibit higher conductivity for the Hg-rich films which decreases linearly as the Zn concentration is increased.     

Effects of deposition temperature and post-annealing on structure and electrical properties in (La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>)CoO<Subscript>3</Subscript> films grown on silicon substrate

(La_0.5Sr_0.5)CoO₃ (LSCO) thin films have been fabricated on silicon substrate by the pulsed laser deposition method. The effects of substrate temperature and post-annealing condition on the structural and electrical properties are investigated. The samples grown above 650°C are fully crystalline with perovskite structure. The film deposited at 700°C has columnar growth with electrical resistivity of about 1.99×10⁻³ Ω cm. The amorphous films grown at 500°C were post-annealed at different conditions. The sample post-annealed at 700°C and 10⁻⁴ Pa has similar microstructure with the sample in situ grown at 700°C and 25 Pa. However, the electrical resistivity of the post-annealed sample is one magnitude higher than that of the in situ grown sample because of the effect of oxygen vacancy. The temperature dependence of resistivity exhibits semiconductor-like character. It was found that post-annealing by rapid thermal process will result in film cracks due to the thermal stress. The results are referential for the applications of LSCO in microelectronic devices.     

Characteristics of Si-doped Sb2Te3 thin films for phase-change random access memory

The characteristics of Si-doped Sb₂Te₃ thin films were investigated using differential scanning calorimetry (DSC), four-point probe technique, X-ray diffraction (XRD) analysis and high resolution transmission electron microscopy (HRTEM). It is found that the as-deposited Sb₂Te₃ film in our study is partly crystallized. Silicon doping increases the crystallization temperature and resistivity of Sb₂Te₃ film significantly. XRD and HRTEM analyses indicated that some of the doped Si atoms substitute for Sb or Te in the lattice, while others exists at the grain boundaries in the form of amorphous phase, which may be responsible for grain size reduction and high crystalline resistivity of Si-doped specimens. Compared with the conventional Ge₂Sb₂Te₅ film, Si-doped Sb₂Te₃ films exhibit lower melting temperature and higher crystalline resistivity, which is beneficial to RESET current reduction of phase-change random access memory (PRAM). These results show the feasibility of Si-doped Sb₂Te₃ films in PRAM application.     

Effect of composition and deposition temperature on the characteristics of Ga doped ZnO thin films

ZnO films doped with Ga (GZO) of varying composition were prepared on Corning glass substrate by radio frequency magnetron sputtering at various deposition temperatures of room temperature, 150, 250 and 400 °C, and their temperature dependent photoelectric and structural properties were correlated with Ga composition. With increasing deposition temperature, the Ga content, at which the lowest electrical resistivity and the best crystallinity were observed, decreased. Films with optimal electrical resistivity of 2-3 × 10⁻⁴ Ω cm and with good crystallinity were obtained in the substrate temperature range from 150 to 250 °C, and the corresponding C_Ga/(C_Ga + C_Zn) atomic ratio was about 0.049. GZO films grown at room temperature had coarse columnar structure and low optical transmittance, while films deposited at 400 °C yielded the highest figure of merit (FOM) due to very low optical absorption despite rather moderate electrical resistivity slightly higher than 4 × 10⁻⁴ Ω cm. The optimum Ga content at which the maximum figure of merit was obtained decreased with increasing deposition temperature.     

A possible role of amorphous regions at grain-boundary vertex points as linear defects on flux pinning in MgB2 films with columnar grain structure

We measured the transport properties of MgB₂ films having columnar grain structure with their axis normal to the substrate. When an external magnetic field was applied parallel to the grain axis, an enhanced critical current density has been observed, and this result has been ascribed to flux pinning induced by grain boundaries. The shape of the angular dependence of critical current density and its magnetic field dependence showed a quite similar resemblance to those of YBa₂Cu₃O_x films containing columnar defects, implying a possible existence of linear defects in MgB₂ films of columnar structure. We propose that the amorphous regions at the vertex points of three or more grain boundaries observed in microstructural studies correspond to the linear defects and these linear defects anchor the end points of the flux line dislocations of Frank-Read sources, by which the shear in the flux line lattice is actuated. This assumed mechanism is found to reasonably explain the magnetic field dependence of the flux pinning force density of MgB₂ films with columnar grain structure.     

Oxygen pressure induced structure,morphology and phase-transition for VO2/c-sapphire films by PLD

To investigate the effects of oxygen pressure on the structural and phase transition properties for VO₂/c-sapphire, highly orientated VO₂ thin films were grown on (0001) sapphire substrates by pulsed laser deposition (PLD) with different oxygen pressures. The crystal structure, morphology and component of the films were systematically investigated. The temperature-dependent resistance (R-T) measurement was conducted, which showed the distinct phase transition characteristic for the prepared films. The results indicate that the oxygen pressure plays an important role for the VO₂ film preparation. The film grown at 1.7 Pa has lower phase transition temperature, higher film strain, and smaller grain size than that at 5.4 Pa, while no obvious crystal phase transition is observed. The experiment suggests that even a small change in oxygen pressure can influence the structure, morphology and phase-transition behavior of VO₂ films obviously, and its potential causes are mainly attributed to the reduction of the kinetic energy to the substrate for target atoms caused by the oxygen pressure, the resulting grain aggregation and interfacial stress.     

Lead-free ferroelectric thin films obtained by pulsed laser deposition

Na_0.5Bi_0.5TiO₃-BaTiO₃ (NBT-BT) thin films grown by pulsed laser deposition have been investigated by X-ray diffraction, scanning electron microscopy, and dielectric spectroscopy in order to clarify the role of substrate temperature on crystalline structure, grain morphology, and dielectric properties. We have shown that the structural and dielectric properties of NBT-BT thin films with composition at morphotropic phase boundary (6% BT) critically depend on the substrate temperature: small variations of this parameter induce structural changes, shifting the morphotropic phase boundary toward tetragonal or rhombohedral side. Higher deposition temperature (1000 K) favor the formation of rhombohedral phase, films deposited at 923 K and 973 K have tetragonal symmetry at room temperature. Grains morphology depends also on the deposition temperature. Atomic force micrographs show grains with square or rectangular shape in a compact structure for films grown at lower temperatures, while grains with triangular shape in a porous structure are observed for films grown at 1000 K. Dielectric spectroscopy measurements evidenced the phase transition between ferroelectric and antiferroelectric phase at 370 K. Films grown at 1000 K shown low electrical resistivity due to their porous structure. High dielectric constant values (about 800 at room temperature and 2700 at 570 K) have been obtained for films grown at temperatures up to 973 K.     

Effect of substrate temperature on structural, optical and electrical properties of pulsed laser ablated nanostructured indium oxide films

Nanocrystalline indium oxide (INO) films are deposited in a back ground oxygen pressure at 0.02 mbar on quartz substrates at different substrate temperatures (T_s) ranging from 300 to 573 K using pulsed laser deposition technique. The films are characterized using GIXRD, XPS, AFM and UV-visible spectroscopy to study the effect of substrate temperature on the structural and optical properties of films. The XRD patterns suggest that the films deposited at room temperature are amorphous in nature and the crystalline nature of the films increases with increase in substrate temperature. Films prepared at T_s ≥ 473 K are polycrystalline in nature (cubic phase). Crystalline grain size calculation based on Debye Scherrer formula indicates that the particle size enhances with the increase in substrate temperature. Lattice constant of the films are calculated from the XRD data. XPS studies suggest that all the INO films consist of both crystalline and amorphous phases. XPS results show an increase in oxygen content with increase in substrate temperature and reveals that the films deposited at higher substrate temperatures exhibit better stoichiometry. The thickness measurements using interferometric techniques show that the film thickness decreases with increase in substrate temperature. Analysis of the optical transmittance data of the films shows a blue shift in the values of optical band gap energy for the films compared to that of the bulk material owing to the quantum confinement effect due to the presence of quantum dots in the films. Refractive index and porosity of the films are also investigated. Room temperature DC electrical measurements shows that the INO films investigated are having relatively high electrical resistivity in the range of 0.80-1.90 Ωm. Low temperature electrical conductivity measurements in the temperature range of 50-300 K for the film deposited at 300 K give a linear Arrhenius plot suggesting thermally activated conduction. Surface morphology studies of the films using AFM reveal the formation of nanostructured indium oxide thin films.     

Two routes to polycrystalline CoSi2 thin films by co-sputtering Co and Si

Two processes for the fabrication of polycrystalline CoSi₂ thin films based on the codeposition of Co and Si by sputtering were studied and compared. The first process involved “annealing after deposition”, where Co and Si are codeposited at ambient temperature and then crystallized by annealing. This process yielded randomly oriented plate-like CoSi₂ grains with a grain size that is governed by the nanostructure of the as-deposited film. Polycrystalline CoSi₂ thin films were obtained at a process temperature of 170 °C, which was much lower than the annealing temperature of 500 °C needed for Co/Si bilayers. The second process involved “heating during deposition”, where Co and Si are codeposited on heated substrates. This process yielded CoSi₂ grains with a columnar structure, and the grain size and degree of (1 1 1) orientation are temperature dependent. The sheet resistance of the resulting films was determined by the preparation temperature regardless of the deposition process used, i.e. “annealing after deposition” or “heating during deposition”. Temperatures of 500 °C and higher were needed to achieve CoSi₂ resistivity of 40 μΩ cm or lower for both processes.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Flux pinning in columnar-structured and single crystalline MgB2 films

We have investigated the flux pinning effect of columnar grain boundary in columnar-structured and single crystalline MgB₂ films. The MgB₂ films with columnar structure showed much higher J_c than that of single crystalline thin film, and sample having smaller grain size had a higher J_c in high magnetic fields. At 5 K, the MgB₂ film with grain size of 460 nm showed an abnormal double-peak behavior in pining force density, F_p(B), caused by competition of different types of pinning sites, such as planar defects and point defects. Field dependences of F_p in columnar-structured films suggest that the columnar grain boundary is a strong pinning source in the MgB₂ film and it plays a crucial role in enhancing J_c over a wide range of magnetic fields and temperatures.     

Heat treatment effects on the structural and electrical properties of thermally deposited AgIn5S8 thin films

The heat treatment effects on structural and electrical properties of thermally deposited AgIn₅S₈ thin films have been investigated. By increasing the annealing temperature of the sample from 450 to 500 K, we observed a change in the crystallization direction from (420) to (311). Further annealing of the AgIn₅S₈ films at 550, 600 and 650 K resulted in larger grain size in the (311) preferred direction. The room temperature electrical resistivity, Hall coefficient and Hall mobility were significantly influenced by higher annealing temperatures. Three impurity levels at 230, 150, and 78 meV were detected for samples annealed at 350 K. The electrical resistivity decreased by four orders of magnitude when the sample annealing temperature was raised from 350 to 450 K. The temperature dependent electrical resistivity and carrier concentration of the thin film samples were studied in the temperature ranges of 25-300 K and 140-300 K, respectively. A degenerate-nondegenerate semiconductor transition at approximately 180 was observed for samples annealed at 450 and 500 K. Similar type of transition was observed at 240 K for samples annealed at 600 and 650 K.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Nd-Fe-B/FeCo多层纳米复合膜的结构和磁性

制备了Nd₂₈Fe₆₆B₆/Fe₅₀Co₅₀多层纳米复合磁性薄膜，对溅射态和650℃退火处理15 min试样的相成分分析和微结构的观察显示，溅射态薄膜呈非晶态，经650℃退火处理15 min后，薄膜主要相成分为硬磁性Nd₂Fe₁₄B相和软磁性相FeCo(110)相.Nd₂Fe₁₄B相呈柱状，其易磁化c轴垂直于膜面，尺寸约10 nm.在硬磁性相和软磁性相之间存在少量富Nd相和非晶态，富Nd相大小约7 nm.磁性测量和分析表明，1)该系列薄膜退火态具有垂直于膜面的磁晶各向异性.2)对于固定厚度(10 nm)层Nd-Fe-B和不同厚度(t_FeCo=1—100 nm)层FeCo多层纳米复合膜,剩磁随软磁相FeCo 厚度的增加快速增加，而矫顽力则减小.当t_FeCo=5 nm时，最大磁能积达到200 kJ/m³. 3)硬磁相Nd-Fe-B层和软磁相FeCo层之间交换耦合导致剩磁和磁能积增强. 关键词： Nd-Fe-B/FeCo多层纳米复合膜 交换耦合 磁各向异性