In掺杂对水热法合成ZnO晶体形貌的影响

本文采用水热法,在ZnO中添加In2O3为前驱物,3mol/L KOH作矿化剂,温度430℃,填充度35;,反应24h,制备了掺In的ZnO晶体.未掺杂In2O3合成的纯ZnO晶体呈六棱锥状,显露负极面-c{0001}、六棱锥面+p{1011}和-p{1011},一般不显露{0001}面.前驱物中掺杂In2O3所合成的ZnO晶体呈六角片状,直径约为5～20 μm,大面积显露{0001}面,另外还显露正锥面+p{1011}、负锥面-p{1011}和负极面-c{0001}.由此可见In掺杂可以明显的改变晶体的形态,使c轴极性快速生长趋向得到明显改善,有利于降低晶体生长缺陷.当采用ZnO晶片为籽晶时,通过水热反应在晶片上生长了一层掺In的ZnO薄膜,通过Hall参数测量得到晶体膜层的电子迁移率约为22cm2/(V·s),载流子浓度约为2×1020 cm-3,具有良好的导电性,同时也说明In可以微量掺入氧化锌晶体.     

Mn、Cu共掺ZnO磁性的研究

本文采用水热法,分别以ZnO、Zn(OH)2为前驱物,添加一定量的MnCl4.4H2O和CuSO4.2H2O, 3mol/LKOH作矿化剂,温度430℃,填充度35%,反应24h,制备了Mn、Cu共掺ZnO晶体。当前驱物为Zn(OH)2时,所得晶体大部分为短柱状晶体,显露正负极面{0001}、{0001-}、负锥面-p{101-1-}和柱面m{1-010},长度约为30 ～50μm。少部分晶体为单锥六棱柱状,显露正锥面p{101-1},柱面m{1-010},负极面-c{0001-},晶体的长度约为100μm,长径比为5:1。当ZnO用作前驱物时,短柱状晶体长度大约为10 ～30μm,晶体的六棱对称性都出现较大的偏差。X射线荧光能谱分析表明,前驱物为ZnO、Zn(OH)2时,Mn离子含量在分别为3.19%和1.62%原子分数,没有检测到Cu离子。虽然Mn、Cu离子的掺入会明显影响晶体形态,磁性测量显示掺杂Mn、Cu的ZnO仍为反铁磁。     

水热法合成Zn1-xMnxO：Sn和Zn1-x-yMnxCoyO：Cu晶体的磁性

本文采用水热法,以ZnO为前驱物,添加适量的MnCl2·4H2O、SnCl2·2H2O和MnCl2·4H2O、CoCl2·6H2O、CuCl2·2H2O,3 mol/L KOH作矿化剂,430℃反应24 h,分别合成了Zn1-xMnxO:Sn晶体和Zn1-x-yMnxCoyO:Cu晶体.用扫描电镜(SEM)对合成物形貌进行分析,结果表明,Zn1-MnxO:Sn晶体为六棱柱状晶体,直径约为10 μm,较大面积显露正极面c{0001},同时也显露负极面-c{0001}、正锥面p{1011}、负锥面-p{1011}和柱面m{1010}.Zn1-x-yMnxCoyO:Cu晶体也显露负极面-c{0001}、正锥面p{1011}、负锥面-p{1011}和柱面m{1010},{0001}显露面小于{0001}.X射线能谱(EDS)分析表明晶体主要成分为ZnO,Mn2 、Co2 离子掺杂量超过2%;SQUID磁性测量显示所合成晶体在25 K具有反铁磁特征,高温为顺磁性.     

水热法合成氧化锌晶体

本文采用水热法,通过改变矿化剂浓度,合成了具有不同晶体形态的氧化锌晶体.在430℃,填充度为35;,矿化剂浓度为1M KOH时,只合成了氧化锌微晶.氧化锌晶体的长度为几百纳米到几微米,晶体形状为六棱锥体.当矿化剂为3M KOH或2M KOH、1M KBr时,合成了高质量的氧化锌晶体.反应 24h后,合成的最大晶体长度(c轴方向)超过1mm,晶体呈单锥六棱柱体,显露柱面m{1010}、锥面p{1011}、负极面o面{0001}.另外还生成多种不同形态的微晶体,最小几微米,中等的几十微米,为六棱锥体,显露锥面p{1011}、负极面o面{0001},没有显露柱面.     

LiOH矿化剂对水热合成ZnO晶体形貌的影响

本文研究了在430℃,填充度为35用了3mol/L,5mol/L LiOH做矿化剂,所获得晶体均为10μm以下的微晶.当矿化剂为1mol/L LiOH和1mol/L KBr时,所获得晶体同样为几微米的微晶,显露完整的正极面{0001}、负极面{0001}、锥面{1011}和柱面{1010}.矿化剂为3M LiOH和3M KBr时,出现个体较大的晶体,直径超过100μm,显露正极面{0001}、正锥面{1011}和柱面{1010},负极面出现缺损现象.由此说明和K+相比溶液中的Li+不利于生成大尺寸ZnO晶体.     

碱土金属离子对ZnO极性生长的影响

本文采用水热法,以3mol/L KOH为矿化剂,填充度35%,温度430℃,通过添加适量比例的MgCl2.7H2O和CaO,合成了非极性生长的ZnO晶体。当Mg2 :Zn2 =2%和Ca2 :Zn2 =2~3%时,晶体c轴方向生长速度明显减弱,{0001}方向的极性生长得到控制,所合成的晶体大面积显露正极面 c{0001},同时显露负极面-c{1001-}、正锥面 p{101-1}、负锥面-p{101-1-}和柱面m{101-0}。X光能谱(EDS)没有检测到晶体中含有碱土金属离子。     

水热合成奇异形态的ZnO晶体

本文采用水热法,以3mol/L KOH为矿化剂,填充度35;,温度430℃,在Zn(OH)2中添加SnCl2·2H2O,添加量为Sn2+:Zn2+=2;条件下,合成出ZnO晶体.产物中除了大量短六棱柱形晶体外,还出现了部分冰激凌形晶体.六棱柱形晶体具有典型的ZnO特征,显露正极面c{0001}、负极面-c{000-1}、柱面m{10-10}、正锥面p{10-11}和负锥面-p{10-1-1}.而冰激凌形晶体有明显的六棱锥晶体外壳,X光能谱(EDS)检测证实晶体各部位的组分均为ZnO.     

In和过渡金属离子共掺杂对ZnO晶体形貌的影响

采用水热法,KOH作矿化剂,在ZnO前驱物中添加适量的CoCl2·6H2O,FeCl2·4 H2O,NiCl2·6H2O,In2O3,其中Co:In:Zn,Fe:In:Zn,Ni:In:Zn 分别为5:1:100,5:1:100,3:1:100.3 mol/L KOH作矿化剂,温度430 ℃,填充度35;,反应24 h,制备了In和过渡族金属离子共掺的ZnO晶体.结果表明,掺杂In2O3时,所合成的过渡族金属离子掺杂的ZnO晶体均呈现六角片状晶体,晶体形貌规则,表面光滑,直径为5～10 μm.和未掺杂In的晶体相比,掺杂In后,晶体c轴极性生长速度得到明显的控制,a、b轴方向生长速度提高,大面积显露+c{0001}、负极面-c{0001}面,另外还显露正锥面+p{1011}、负锥面-p{101-1-}.     

水热法合成Mnx Zn1-xO微晶体

本文采用水热法合成了MnxZn1-xO晶体,水热反应条件为3mol·L-1KOH作为矿化剂,填充度为35;,温度为430℃,在Zn(OH)2中添加一定量的MnO2为前驱物,反应时间为24h.通过X射线能谱仪测量了晶体中的Mn含量,随着前驱物中MnO2含量的增加,晶体中Mn的原子百分比随着增加,Mn最大原子百分比含量超过了2;,晶体的形貌具有纯ZnO晶体的六角柱形特征.显露柱面m{1010}、锥面p{1011}、负极面O面{0001}和正极面{0001}.晶体直径为50～200μm,高度为20～100μm.     

水热法合成Zn1-xMnxO稀磁半导体

本文采用水热法在430℃,以3mol%.L-1KOH作矿化剂,填充度为35%,反应时间24h,合成了Zn1-xMnxO稀磁半导体晶体。所合成晶体具有ZnO纤锌矿结构,晶面显露正极面{0001}、负极面{0001}、菱面{1011}及负菱面{1011}晶体高度为5~30μm,径高比约为2:1。X荧光能谱(EDS)显示Mn原子百分浓度为2.6%(x=0.026)。晶体呈现低温铁磁性,居里温度50K。     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.