Effect of Cr and Co Promoters Addition on Vanadium Phosphate Catalysts for Mild Oxidation of n-Butane

In this study, Cr and Co promoted, as well as unpromoted vanadium phosphate (VPO) catalysts were synthesized by the reaction of V2O5 and o-H3PO4 in organic medium followed by calcination in n-butane/air environment at 673 K. The physico-chemical properties and the catalytic behavior were affected by the addition of Cr and Co dopants. H2-TPR was used to investigate the nature of oxidants in the unpromoted and promoted catalysts. The results showed that both the Cr and Co promoters remarkably lowered the temperature of the reduction peak associated with V5 . The amount of oxygen species originated from the active phase, V4 , removed was significantly increased for Co and Cr-promoted catalysts. Both Cr and Co dopants improve strongly the n-butane conversion without sacrificing the MA selectivity. A good correlation was observed between the amount of oxygen species removed from V4 phase and the activity for n-butane oxidation to maleic anhydride. This suggested that V4 -O was the center for the activation of n-butane.     

Ammonia Decomposition over Bimetallic Nitrides Supported on γ-Al2O3

A series of monometallic nitrides and bimetallic nit-rides were prepared by temperature-programmed reaction with NH3. The effects of Co, Ni and Fe additives and the synergic action between Fe, Co, Ni and Mo on the ammonia decomposition activity were investigated. TPR-MS, XRD were also carded out to obtain better insight into the structure of the bimetallic nitride. The results of ammonia decomposition activity show that bimetallic nitrides are more active than monometallic nitrides or bimetallic oxides.     

Selective Oxidation of n-Butane over VPO Catalyst Modified by Different Additives

A series of vanadyl pyrophosphate catalyst （VPO） modified by different additives have been prepared with the aim to study the performance for selective conversion of n-butane to maleic anhydride（MA）. The addition of various promoters improved the catalytic performance remarkably on both activity and selectivity. The correlation of activity and selectivity of the catalysts with their structure has been discussed. The increase in BET surface areas and surface redox sites leads to an enhanced activity. However, good selectivity can only be obtained on those surfaces with suitable surface acid sites.     

A Novel Way to Prepare γ-Al2O3 Supported SO42-/ZrO2 Solid Superacid Catalysts for n-Butane Isomerization

Highly active solid superacid catalysts for n-butane isomerization, SZ/Al2O3-P, were prepared by supporting SO42-/ZrO2 (SZ) on γ-Al2O3 carrier using a precipitation method.The activities of some catalysts were enhanced significantly.The activity of the most active sample, 60%SZ/Al2O3-P, was even about 2 times more active than that of the SZ catalyst.     

Complete Oxidation of Methane Alumina Modified with Calcium, over Palladium Supported on Lanthanum, and Cerium Ions

The activity and thermal stability of Pd/Al2O3 and Pd/（Al2O3＋MOx） （M=Ca, La, Ce） palladium catalysts in the reaction of complete oxidation of methane are presented in this study. The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide. Then they were impregnated with palladium nitrate solution. The catalysts with unmodified alumina had a high surface area. The activity and thermal stability of the aluminasupported catalyst was also very high. The introduction of calcium, lanthanum, or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method. These modifiers decreased the activity of palladium catalysts, and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al2O3. The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.     

Autothermal Reforming of Methane over Ni Catalysts Supported on CuO-ZrO2-CeO2-Al2O3

Ni catalysts supported on various mixed oxides of Al2O3 with rare earth oxide and transitional metal oxides were synthesized. The studies focused on the measurement of the autothermal reforming of methane to hydrogen over Ni catalysts supported on the mixed oxide ZrxCe30-xAl70Oδ (x=5, 10, 15). The catalytic performance of Ni/Zr10Ce20Al70Oδ was better than that of other catalysts. XRD results showed that the addition of Zr to Ni/Ce30Al70Oδ prevented the formation of NiAl2O4 and facilitated the dispersion of NiO. Effects of CuO addition to Zr10Ce20Al70Oδ were also investigated. The activity of Ni catalyst supported on CuO-ZrO2-CeO2-Al2O3 was somewhat affected and the Ni/Cu5Zr10Ce20Al65Oδ showed the best catalytic performance with the highest CH4 conversion, yield of H2, selectivity for H2 and H2/CO production ratio in operation temperatures ranging from 650 to 750℃.     

Catalytic Oxidation of Dimethyl Ether to Dimethoxymethane over Cs Modified HaPW12O40/SiO2 Catalysts

The attractive utilization route for one-step catalytic oxidation of dimethyl ether to dimethoxymethane was successfully carried out over the H3PW12O40（40%）/SiO2 catalyst, modified by Cs, K, Ni, and V. The Cs modification of H3PW12O40（40%）/SiO2 gave the most promising result of 20% dimethyl ether conversion and 34.8% dimethoxymethane selectivity. Dimethoxymethane could be synthe- sized via methoxy groups decomposed from dimethyl ether through the synergistic effect between the acid sites and the redox sites of Cs modified H3PW12O40（40%）/SiO2.     

The Process of Acetonitrile Synthesis over γ-Al2O3 Promoted by Phosphoric Acid Catalysts

The influence of principal parameters (reaction temperature, ratio of acetic acid and ammonia, composition of reactionary mixture and promotion of catalysts) on the selectivity and yield of the desired product was studied in the reaction of catalytic acetonitrile synthesis by ammonolysis of acetic acid. The processing of γ-Al₂O₃ by phosphoric acid increases amount of the centers, on which carries out reaction of acetamide dehydration. The kinetic model of a limiting stage of reaction – the acetamide dehydration to acetonitrile was suggested. In the process of ammonolysis of acetic acid it was demonstrated that the use of catalysts promoted by phosphoric acid and ratio NH₃:CH₃COOH=(3-4):1 at temperatures of a reactor 360-390°С leads to the increase of acetonitrile productivity to 0.7-0.8 g/cm³·h and allows to minimize formation of by-products.     

SO2-4/ZrO2-Al2O3及载Pt催化剂上正丁烷异构化反应

研究了ＳＯ４＾２－／ＺrＯ２－Ａl２Ｏ３固体超强酸催化剂与制备条件的关系,探讨了催化剂表面结构及晶化程度,并在Ｎ２活化条件下用脉冲色谱法考察了催化剂催化正丁烷异构化反庆活性。结果表明,添加Ａ１可提高催化剂的催化剂的催化活性,降低反应温度,载铂对提高催化剂的活性和稳定性更为有效。     

γ-Al2O3负载Cr促进SO2-4/ZrO2固体超强酸研究

将Ｃｒ促进的ＳＯ＾２－４／ＺｒＯ２（ＳＺ）固体超强酸Ｃｒ－ＳＺ负载于γ－Ａｌ２Ｏ３载体上,制成Ｃｒ－ＳＺ／Ａｌ２Ｏ３系列固体超强酸,利用探针反应考察了其超强酸性,中强酸性和弱酸性的变化情况,详细研究了样品的比表面、硫含量、ＺｒＯ２晶化情况及正丁烷低温异构化反应活性,结果发现,负载后部分Ｃｒ－ＳＺ的正丁烷低温异构化反应活性显著提高,含铬样品酸强度和脱氢性能的增强对其正丁烷异构化反应活性的提高均有贡献,样品酸性和脱氢性之间的合适匹配使Ｃｒ－ＳＺ／Ａｌ２Ｏ３显示出很高的正丁烷异构化反应活性。     

Promotional Effect of Bismuth as Dopant in Bi-Doped Vanadyl Pyrophosphate Catalysts for Selective Oxidation of n-Butane to Maleic Anhydride

Bismuth-promoted (1% and 3%) vanadyl pyrophosphate catalysts were prepared by refluxing Bi(NO3)3·5H2O and VOPO4·2H2O in isobutanol. The incorporation of Bi into the catalysts lattice increased the surface area and lowered the overall V oxidation state. Profiles of temperature programmed reduction (TPR) in H2 show a significant shift of the maxima of major reduction peaks to lower temperatures for the Bi-promoted catalysts. A new peak was also observed at the low temperature region for the catalyst with 3% of Bi dopant. The addition of Bi also increased the total amount of oxygen removed from the catalysts. The reduction pattern and reactivity information provide fundamental insight into the catalytic properties of the catalysts. Bi-promoted catalysts were found to be highly active (71% and 81% conversion for 1% and 3% Bi promoted catalysts, respectively, at 703 K), as compared to the unpromoted material (47% conversion). The higher activity of the Bi-promoted catalysts is due to that these catalysts possess highly active and labile lattice oxygen. The better catalytic performance can also be attributed to the larger surface area.     

Selective Oxidation of CO in Excess H2 over Ru/Al2O3 Catalysts Modified with Metal Oxide

The Ru/Al_2O_3 catalysts modified with metal oxide(K_2O and La_2O_3)were prepared via incipient wetness impregnation method from RuCl_3·nH_2O mixed with nitrate loading on Al_2O3 support. The activity of catalysts was evaluated under simulative conditions for the preferential oxidation of CO (CO-PROX)from the hydrogen-rich gas streams produced by reforming gas,and the performances of catalysts were investigated by XRD and TPR.The results showed that the activity temperature of the modified catalysts Ru-K_2O/Al_2O3 and Ru-La_2O_3/Al_2O_3 were lowered approximately 30℃compared with pure Ru/Al_2O_3,and the activity temperature range was widened.The conversion of CO on Ru-K_2O/Al_2O_3 and Ru-La_2O_3/Al_2O_3 was above 99% at 140-160℃,suitable to remove CO in a hydrogen-rich gas and the selectivity of Ru-La_2O_3/Al_2O_3 was higher than that of Ru-K_2O/Al_2O_3 in the active temperature range. Slight methanation reaction was detected at 220℃and above.     

Catalytic Combustion of Methane over MnOx／ZrO2-Al2O3 Catalysts

MnOx/Al2O3 and MnOx/ZrO2-Al2O3 catalysts were prepared by incipient wetness impregnation of Mn(CH3COO)2 on the corresponding supports, followed by the characterization using X-ray diffraction (XRD). temperature programmed reduction (TPR) and BET surface area techniques. The result shows the BET surface area of ZrO2-Al2O3 is lower than that of Al2O3 due to the loading of ZrO2.However tile resulted MnOx/ZrO2-Al2O3 catalyst exhibits higher activity for methane combustion than MnOx/Al2O3, because the addition of ZrO2 onto Al2O3 is beneficial for the dispersion of Mn species and the improvement of the lattice oxygen activity in MnOx. subsequently the activation of methane during combustion. The optimum loading of Zr in MnOx/ZrO2-Al2O3 is in the range of 5%-10% correlated with the calcination temperatures of catalyst supports.     

Nickel Supported on Alkaline Earth Metal–Doped γ-Al2O3–La2O3 as Catalysts for Dry Reforming of Methane

Russian Journal of Applied Chemistry - Nickel catalysts supported on γ–Al2O3 doped with La2O3 and alkaline earth oxides (MgO, CaO, and SrO) were investigated in the dry reforming of...     

Preparation of Nano-Sized γ-Al2O3 Supported Iron Catalyst for Fischer-Tropsch Synthesis by Solvated Metal Atom Impregnation Methods

Two types of small iron clusters supported onγ-Al2O3-RT(dehydroxylated at room temperature) andγ-Al2O3-800 (dehydroxylated at 800℃) were prepared by solvated metal atom impregnation (SMAI) techniques. The iron atom precursor complex, bis(toluene)iron(0) formed in the metal atom reactor, was impregnated intoγ-Al2O3 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by TEM, Mossbauer, and chemisorption measurements, and the results show that higher concentration of surface hydroxyl groups ofγ-Al2O3-RT favors the formation of more positively charged supported iron cluster Fen/γ-Al2O3-RT, and the lower concentration of surface hydroxyl groups ofγ-Al2O3-800 favors the formation of basically neutral supported iron cluster Fen/γ-Al2O3-800. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the rapid decomposition of precursor complex, bis(toluene)iron(0), and favors the formation of relatively large iron cluster. Consequently, these two types of catalysts show different catalytic properties in Fischer-Tropsch reaction. The catalytic pattern of Fen/γ-Al2O3-RT in F-T reaction is similar to that of the unreducedα-Fe2O3 and that of Fen/γ-Al2O3-800 is similar to that of the reducedα-Fe2O3.     

Metathesis of Butylene-2 and Ethylene to Propylene over 3.0Mo／（Hβ＋γ-Al2O3） Catalysts with Different γ-Al2O3 Contents

A series of 3. OMo/(Hβ γ-Al2O3) samples with γ-Al2O3 contents in the range of 0-100% (mass fraction) was studied by means of XRD, NH3-TPD, TPR and BET determinations for characterizing their structures. The Hβ zeolite structure in the 3.0Mo/Hβ sample can be effectively stabilized by adding some γ-Al2O3 to Hβ zeolite. γ-Al2O3 mainly favors the formation of polymolybdate or multilayered Mo oxide, while Hβ mainly forms the Al2(MoO4)3 species, as evaluated by the TPR technique. When used as the catalyst for the metathesis of butylene-2 and ethylene to propylene, there exists a close correlation between the specific surface area and stability of the catalyst. The specific surface area of the catalyst shows the maximum when (Hβ γ-Al2O3) contains 30%γ-Al2O3, which is in agreement with that of the time needed for the reaction stablization. In the case of maximum surface area, the rate of coke deposition is the minimum.