不同方法制备Ni-WO_3/TiO_2-ZrO_2催化剂及其性能研究

考察了Ti O2-Zr O2载体制备方法对Ni-WO3/Ti O2-Zr O2催化正庚烷异构化反应性能的影响.通过BET、XRD、SEM和NH3-TPD的表征结果表明,以模板-溶胶-凝胶法制备Ti O2-Zr O2载体时,Ni-WO3/Ti O2-Zr O2催化剂晶相结晶度较好,具有较适宜的表面酸性和比表面积,从而在正庚烷异构化反应中表现出较高的催化活性和选择性,正庚烷的转化率和异庚烷的选择性分别为72.62%和80.81%.实验结果还表明,Ti O2-Zr O2比Zr O2、Si O2-Zr O2和Al2O3-Zr O2更适宜作为载体制备催化剂应用于正庚烷异构化的反应中.     

Hydrogen effects on the electric conductivity of a Pt/Al2O3 catalyst

Hydrogen desorption, hydrogen spillover and reduction processes have been evidenced using a new experimental strategy based on AC electric conductivity measurements during TPD and TPR experiments on a 0.5% Pt/Al₂O₃ catalyst.     

Methane Coupling Using Hydrogen Plasma and Pt／γ—Al2O3 Catalyst

In this paper,methane coupling at ambient temperature, under atmospheric pressure and in the presence of hydrogen was firstly investigated by using pulse corona plasma and Pt/γ-Al2O3 catalyst. Experimental results showed that Pt/γ-Al2O3 catalyst has catalytic activity for methane couplin to C2H4. Over sixty percent o outcomes of C2 hydrocarbons were detected to be ethylene.     

水合氧化锆的晶化方式对Pt/WO3-ZrO2异构化活性的影响

 采用不同方法制备了一系列具有一定晶相结构的水合 ZrO2, 考察了制备方法对水合 ZrO2 晶化方式及 Pt/WO3-ZrO2 催化剂催化正己烷异构化活性的影响. 采用 X射线衍射, Raman 光谱和 NH3-程序升温脱附对催化剂进行了表征. 结果表明, 水合 ZrO2 的晶化方式与制备时氧气的存在与否有关, 也大大影响了催化剂的异构化活性. 以无氧条件下制备的水合 ZrO2 为载体时, Pt/WO3-ZrO2 催化剂具有较高的异构化活性, 而以在空气气氛中制得的水合 ZrO2 为载体时, Pt/WO3-ZrO2 几乎无异构化活性.     

WO3-TiO2/SiO2的制备、表征及光催化甲烷和水的反应性能

以表面改性法制备出TiO2／SiO2，进而以浸渍法制备出负载型复合半导体材料WO3-TiO2／SiO3，利用XRD、BET、TPR、UVDRS、IR和TPD等技术对材料的表面性质与构造、光响应性能和化学吸附性能进行了表征，并研究了该材料光催化甲烷和水合成甲醇和氢的反应性能．结果表明：载体有效分散表面物种并使其能隙增大；WO3与TiO2复合所形成的组合活性基元可调变吸光带边并促进对甲烷和水的化学吸附；在100℃以上，光激发WO3-TiO2／SiO2表面产生的光生空穴，促使分子吸附态的甲烷解离并向甲醇转化，形成一定的“光-表面-热”协同作用促使反应顺利进行，对甲醇的选择性达到83％以上．     

Pt/Al2O3催化剂还原方法对Pt粒子表面性质的影响

以CO吸附红外光谱结合CO化学吸附、透射电镜和能量散射谱等手段,研究了Pt/Al₂O₃制备过程中还原方法对最终Pt粒子表面活性位分布、粒径大小和表面残余氯等表面性质的影响,重点考察了普通的气相氢气还原和甲酸钠水溶液还原两种方法的对比。结果表明,采用氢气气相还原时,Pt/Al₂O₃上Pt粒子表面台阶位和平台位比例基本不随焙烧温度而变;而采用甲酸钠水溶液还原时,Pt粒子表面台阶位所占比例随焙烧温度升高而提高。水的存在和还原条件剧烈这两个因素使得水相甲酸钠还原不利于Pt的分散,所得Pt/Al₂O₃上Pt的分散度比氢气气相还原所得要小。无论何种还原条件,水的存在都有利于Pt前躯体中的氯从Pt/Al₂O₃表面去除;而氢气气相还原所得催化剂表面则有大量残余氯存在。     

甲烷部分氧化制合成气反应Pt/Al_2O_3和Pt/CeO2/Al_2O_3催化剂的研究(英文)

研究了Ｐｔ／Ａｌ２Ｏ３和Ｐｔ／ＣｅＯ２／Ａｌ２Ｏ３催化剂对甲烷部分氧化制合成气反应的催化活性，发现Ｐｔ／ＣｅＯ２／Ａｌ２Ｏ３显示了比Ｐｔ／Ａｌ２Ｏ３更高的甲烷转化率和合成气选择性。用Ｈ２ＴＰＲ，Ｈ２ＴＰＤ，ＳＥＭ和ＸＲＤ等手段和技术对催化剂进行了表征。ＣｅＯ２与Ｐｔ之间存在较强的相互作用（ＳＭＳＩ），这种作用促进了Ｐｔ在催化剂表面的分散，抑制了Ｐｔ在催化剂表面的迁移，大大降低了催化剂在反应中的完全燃烧活性，提高了催化剂的部分氧化活性和选择性，避免了因催化剂床层局部温度过高而导致催化剂活性下降或失活，提高了催化剂的稳定性。同时，在反应过程中，ＣｅＯ２通过促进水蒸气变换反应（ＷＧＳＲ）的进行使反应体系迅速达到平衡，提高了催化剂对Ｈ２的选择性。     

Unravelling the Promotional Effect of La2O3 in Pt/La-TiO2 Catalysts for CO2 Hydrogenation

This work reports the preparation of a La₂O₃-modified Pt/TiO₂ (Pt/La-TiO₂) hybrid through an excess-solution impregnation method and its application for CO₂ hydrogenation catalysis. The Pt/La-TiO₂ catalyst is characterized by XRD, H₂ temperature-programmed reduction (TPR), TEM, X-ray photoelectron spectroscopy (XPS), Raman, EPR, and N₂ sorption measurements. The Pt/La-TiO₂ composite starts to catalyze the CO₂ conversion reaction at 220 °C, which is 30 °C lower than the Pt/TiO₂ catalyst. The generation of CH₄ and CO of Pt/La-TiO₂ is 1.6 and 1.4 times greater than that of Pt/TiO₂. The CO₂ temperature-programmed desorption (TPD) analysis confirms the strengthened CO₂ adsorption on Pt/La-TiO₂. Moreover, the in situ FTIR experiments demonstrate that the enhanced CO₂ adsorption of Pt/La-TiO₂ facilitates the formation of the active Pt–CO intermediate and subsequently boosts the evolution of CH₄ and CO. The cycling tests reveal that Pt/La-TiO₂ shows reinforced stability for the CO₂ hydrogenation reaction because the La species can prevent Pt nanoparticles (NPs) from sintering. This work may provide some guidance on the development new rare-metal-modified hybrid catalysts for CO₂ fixation.     

A Novel CFC-12 Hydrolysis Catalyst: WO3/SnO2

Thousands of studies have continuously confirmed that chlorofluorocarbons (CFCs) arekillers of the stratospheric ozone which protects life on earth against harmful ultravioletradiation from the sun'. Although many CFCs have been banned since the MontrealProtocol, there are still 2.25 million ton CFCs all over the world and numerous airconditioning systems still use them. These CFCs are leaking out of existing equipmentsand will not be degraded in nature for 50-100 years because of their c…     

Pt/Al2O3和Pt-Cu/Al2O3催化CCl4氢化脱氯反应

制备了Al2O3负载Pt单金属催化剂和负载Pt-Cu双金属催化剂,比较了二者不同还原温度对其催化CCl4氢化脱氯反应性能的影响。 单金属Pt催化剂上主要生成CHCl3,而双金属Pt-Cu催化剂上产物随催化剂制备时的还原温度不同而异,当催化剂经400 ℃用H2还原后产物主要为CHCl3,而当催化剂经800 ℃用H2还原后产物主要为CCl2CCl2。 由于CCl4氢化反应是强放热反应,催化剂表面局部过热使得在反应中生成的C2等产物聚合结焦,覆盖了催化剂的活性中心,导致催化剂失活。 因此,通过加入甲醇作为稀释剂以带走部分反应热可提高催化剂的稳定性。 同时也降低了CHCl3的选择性,提高了CCl2CCl2的选择性。     

以水热法合成的水合氧化锆为载体的Pt／WO3-ZrO2上的正己烷异构化

通过水热法合成了一系列水合氧化锆,以之为载体采用浸渍法制备了Pt/WO3-ZrO2催化剂,考察了氢氧化锆的水热温度对Pt/WO3-ZrO2异构化活性的影响.通过X射线衍射、NH3程序升温脱附及H2程序升温还原表征了样品的晶相结构、酸性及还原性能.结果表明,水合氧化锆及以此为载体的催化剂的晶相结构均随着氢氧化锆水热温度的变化而变化,水热温度升高,四方相氧化锆比例下降.具有一定晶相结构的水合氧化锆为载体的催化剂具有较无定形氢氧化锆为载体的催化剂更多的强酸中心和更高的异构化催化活性.高的异构化活性可能与催化剂上更多的强酸中心有关。     

载体对Pt/WO_3-ZrO_2催化临氢异构反应性能的影响

以平衡吸附过氧钨酸的水合氧化锆为前驱体,经焙烧得到WO_3-ZrO_2固体酸,并采用XRD、UV-vis、NH_3-TPD等手段考察了过氧钨酸吸附液浓度及焙烧温度对WO_3-ZrO_2固体酸组成、结构及酸性的影响。通过BET、H_2-TPR、H_2-TPD等表征手段和正戊烷临氢异构反应,考察了负载铂后相应催化剂的结构、还原与氢吸附性质及其催化正戊烷临氢异构反应的性能。结果表明,焙烧温度为700℃时,随着吸附液浓度的增加,所得载体酸度及相应催化剂比表面积均先增加后减小,且在吸附液浓度为82 mmol W/L时达到最大值。吸附液浓度为59 mmol W/L时,随着焙烧温度的升高,所得载体四方相氧化锆含量、酸度及相应催化剂比表面积均降低。吸附液浓度为82 mmol W/L、焙烧温度为700℃所得载体负载0.5%(质量分数)铂后催化活性最高。该催化剂在250℃常压临氢操作、n(H_2)/n(n-C_5H_(12))为3、WHSV为1.0 h~(-1)的条件下,催化正戊烷异构反应中异戊烷收率可达57.7%。     

Activity Enhancement of Pt/Ba/Al2O3 Mixed with Mn/Ba/Al2O3 for NOx Storage-reduction by Hydrogen

The storage and reduction of nitrogen oxides has attracted much attention as an efficient way to reduce NOx emission of lean-burn gasoline and diesel engines1-5. At present, NOx storage and reduction (NSR) catalysts based on Pt and Ba have been extensivel…     

Pt/Al2O3和Pt/CeO2/Al2O3催化甲烷部分氧化制合成气反应

研究了Pt/Al₂O₃和Pt/CeO₂/Al₂O₃对甲烷部分氧化制合成气反应的催化活性,发现Pt/CeO₂/Al₂O₃显示了更高的甲烷转化率和合成气选择性.用H₂-TPR、H₂-TPD、SEM-EDX和XRD等技术对催化剂进行了表征.CeO₂和Pt相互作用促进Pt在催化剂表面的分散,抑制Pt在催化剂表面的迁移;降低了催化剂的燃烧活性,提高了催化剂的部分氧化活性和选择性,可避免因催化剂床层局部温度过高而导致催化剂活性下降或失活,提高了催化剂的稳定性.同时,CeO₂通过促进水汽变换反应使反应体系迅速达到平衡,提高了催化剂对H₂的选择性.     

Transformation of n-hexane on Al2O3and SiO2supported Pt, Pt+Ga and Ir+Pt+Ga catalysts prepared by anchoring methods

Summary Transformation of n-hexane over Al₂O₃and SiO₂supported Pt, Pt+Ga and Ir+Pt+Ga catalysts was studied in a continuous-flow reactor operated under slug-pulse mode at 520°C. Bimetallic catalysts were prepared by introducing first Ga(OEt)₃and then diallylplatinum as precursor compounds. Iridium was then introduced viadecomposition of Ir₄(CO)₁₂adsorbed onto Pt+Ga catalysts. The addition of Ga to Pt/SiO₂catalyst decreased hydrogenation, aromatization and hydrogenolysis selectivity. Over Pt/Al₂O₃catalyst Ga increased hydrogenolysis selectivity and decreased isomerization and C₅-cyclization. The main effect of Ir was to increase hydrogenolysis selectivity and the stability of catalysts.</o:p>     

Pt/TiO_2光催化降解3-甲基吲哚的研究

Pt/TiO_2 was prepared by impregnation method and characterized with XRD、 BET and XRD results showed TiO_2 as prepared was anatase and the average particle sizewas about17 nm.The results of the photocatalytic degradation of 3- methyl indole suggested that the influences of Pt amount and loading amount of catalytics have obvious effect to catalyst activity.The concentration of flow rate and consistence obviously influenced the 3- methyl indole photocatalytic degradation.     

A Novel Biomimetic Hydrogen Peroxide Biosensor Based on Pt Flowers‐decorated Fe3O4/Graphene Nanocomposite

A sensitive and selective amperometric H₂O₂ biosensor was obtained by utilizing the electrodeposition of Pt flowers on iron oxide‐reduced graphene oxide (Fe₃O₄/rGO) nanocomposite modified glassy carbon electrode (GCE). The morphology of Fe₃O₄/rGO and Pt/Fe₃O₄/rGO was characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. The step‐wise modification and the electrochemical characteristics of the resulting biosensor were characterized by cyclic voltammetry (CV) and chronoamperometry methods. Thanks to the fast electron transfer at the Pt/Fe₃O₄/rGO electrode interface, the developed biosensor exhibits a fast and linear amperometric response upon H₂O₂. The linear range of Pt/Fe₃O₄/rGO is 0.1∼2.4 mM (R²=0.998), with a sensitivity of 6.875 μA/mM and a detection limit of 1.58 μM (S/N=3). In addition, the prepared biosensor also provides good anti‐interferent ability and long‐term stability due to the favorable biocompatibility of the electrode interface. The proposed sensor will become a reliable and effective tool for monitoring and sensing the H₂O₂ in complicate environment.     

H2在WO3表面解离吸附反应的第一性原理研究

采用第一性原理方法对H2在WO3表面的解离吸附反应进行了研究.首先通过清洁表面模型的计算,证明了c(2×2)重构表面是最稳定的WO3(001)表面构型;进而研究了4种可能的H2解离吸附模型,结果表明最可能的吸附反应为两个氢原子吸附在表面O1c原子上,氢原子被氧化在表面形成水,同时伴随着产生一个表面氧空位.态密度结果表明氢的吸附导致体系能带下移,导带部分填充电子,从而阐明了实验中WO3吸附H2后电导率上升的微观机理.     

封装型Pt/SOD分子筛的合成及表征

基于封装型贵金属分子筛的合成,充分利用其择形性和氢溢流特性构建新型加氢催化剂,选定Pt作为活性组分,方钠石作为载体,通过水热合成法直接将金属前驱体Pt(NH_3)_4Cl_2引进SOD合成母液中进行晶化,合成了不同封装量的Pt/SOD分子筛。采用苯加氢反应测试样品的催化活性,并运用XRD、SEM、TEM和H_2-TPD对样品进行表征。结果表明,合成的不同封装量的Pt/SOD样品均具有良好的催化活性,与溢流氢受体HZSM-5间均具有良好的氢溢流效应。其中,当金属前驱体Pt(NH_3)_4Cl_2的用量为(Pt(NH_3)_4Cl_2)∶(Si-Algel)比为0.030 g/g时,所合成的Pt/SOD样品最佳,催化苯加氢反应的苯转化率可达54.38%。     

NiO/WO3/TiO2-Al2O3催化剂上正庚烷的临氢异构化

采用溶胶凝胶法制备了TiO2-Al2O3复合载体,用分步浸渍法制备了NiO/WO3/TiO2-Al2O3催化剂。 在常压连续流动固定床反应器上考察了NiO/WO3/TiO2-Al2O3对正庚烷临氢异构化反应的催化性能。 研究了催化剂中WO3含量、Ni含量、焙烧温度和还原温度及催化反应温度对临氢异构化反应的影响。 采用XRD和BET方法对催化剂进行了表征。 结果表明,当w(WO3)=25%、w(Ni)=10%时,所制备的NiO/WO3/TiO2-Al2O3催化剂对正庚烷异构化反应的催化性能最好,活性可达15.50%,选择性可达84.06%。