Theoretical Study on Wavelength Conversion Based on Cross Phase Modulation Using Semiconductor Optical Amplifiers

Performances of wavelength converted signal by cross phase modulation (XPM) using semiconductor optical amplifiers (SOA's) were studied by the use of the multi-section model. Results show that they are related to both the phase arm bias current of the XPM wavelength converter and its operation. When the conversion is under the in-phase operation, the peak extinction ratio (ER) and the chirp frequency of the converted signal increase according to the decrease of the phase arm bias current, but the input signal power dynamic range decreases. When the converter is under the out-of-phase operation, the chirp frequency decreases with the decrease of the phase arm bias current, while the peak ER and the input power dynamic range keep almost the same when the phase arm bias current changes.     

基于线性光放大器的交叉相位调制波长转换啁啾特性研究

建立了基于线性光放大器(LOA)的交叉相位调制波长转换模型,模型考虑了纵向载流子密度变化引起的有源区折射率的改变、端面反射、相位调制、放大的自发辐射噪声和横向垂直光场(VCL)的增益钳制作用。利用分段方法模拟计算了布拉格反射镜的反射率、偏置电流、信号光和探测光的功率和波长、信号速率与转换后信号啁啾的关系。结果表明:LOA具有增益钳制作用,能提高转换后信号的性能;增大布拉格反射镜的反射率可以降低转换后信号的啁啾;合理控制输入信号光和探测光的强度,调整干涉仪两臂LOA偏置电流的强度,可以获得啁啾较小的转换信号。     

基于单端耦合SOA的波长转换器啁啾特性分析

提出了一种基于单端半导体光放大器（SOA）的交叉增益调制型（XGM）全光波长转换器结构, 并针对这种结构建立了动态理论模型, 以这个模型为基础分析了泵浦光功率、探测光功率、输出消光比、输入消光比对转换后信号啁啾的影响. 结果表明利用这种结构的波长转换器实现波长转换, 在提高输出消光比的同时也降低了转换光的啁啾, 较传统的波长转换器是一种改进.     

Experimental study of SOA-based NRZ-to-PRZ conversion and distortion elimination of amplified NRZ signal using spectral filtering

We experimentally study both reshaping of nonreturn-to-zero (NRZ) signal and NRZ to pseudoreturn-to-zero (PRZ) format conversion based on self-phase modulation of a semiconductor optical amplifier (SOA) and detuning an optical bandpass filter (OBF). When an OBF with 1 nm bandwidth is blue shifted by 0.8 nm, the distortion of the amplified NRZ signal at 10 Gbit/s is shown to be eliminated completely. When an OBF with 0.32 nm bandwidth is red shifted by 0.42 nm from the carrier frequency, NRZ-to-PRZ conversion at 10 Gbit/s is obtained. A holding beam is used to suppress the SOA noise and improve the output extinction ratio (ER). The output ER of both the reshaped NRZ and the converted PRZ is larger than 10 dB when the signal wavelength is longer than 1540 nm, and an input power dynamic range from −7 dBm to 2 dBm is obtained at a signal wavelength of 1563.6 nm. The average power of the reshaped NRZ signal is about 3 dBm at an input power dynamic range of 13 dB. The amplitude fluctuation of the converted PRZ signal is around 1.6 dB.     

基于半导体光放大器中交叉增益调制效应的波长转换啁啾特性的分析

对基于半导体光放大器中交叉增益调制效应的波长转换后信号的啁啾特性进行了分析。研究了输入信号光和参考光和功率、波长、转换速率、信号光消光比以及半导体光放大器的偏置电流对转换后信号啁啾的影响。     

Characteristics of the Wavelength Converted Signal in Wavelength Conversion Based on Cross-Gain Modulation

An analytical theory describing the frequency chirp characteristics of the wavelength converted signal in wavelength conversion based on cross-gain modulation (XGM) in semiconductor optical amplifier (SOA) is derived. By computation, we can see that low input pump power, high probe power, small line-width enhancement factor and low unsaturated single-pass gain of the SOA are favorable for reducing the frequency chirp of the wavelength converted signal. The analytical results have significance in understanding and designing wavelength converters.     

Simultaneous chromatic dispersion monitoring,extinction ratio enhancement and wavelength conversion using four-wave mixing

This paper presents a multi-functional all-optical device performs simultaneous chromatic dispersion (CD) monitoring, extinction ratio (ER) improvement and tunable wavelength conversion using four-wave mixing (FWM) in a single piece of highly nonlinear optical fiber (HNLF). The multi-functional ability arises from the nonlinear power transfer function (PTF) between the input signal and the output idler wave, which not only maps the CD information of the signal onto the average power of idler wave, but also transfers the data information to the idler wave with ER enhancement, making the device compact and cost effective. Furthermore within the wavelength tuning range the monitoring sensitivity and output ER can be much higher compared to all optical monitors and regenerators proposed before. Numerical simulations are then used to demonstrate the efficiency of this method.     

基于SFRL的FWM型可调谐波长转换器啁啾特性分析

基于半导体光纤环形腔激光器的四波混频型可调谐全光波长转换器的宽带理论模型,从理论上研究了输入信号光功率、注入电流、两个耦合器的耦合比、激射光波长和半导体光放大器有源区长度对转换光频率啁啾的影响.结果表明:转换光的频率啁啾随着输入信号光峰值功率、注入电流以及SOA有源区长度的增大而增大,随两个耦合器耦合比的增大而减小.     

半导体激光器型全光波长转换器的啁啾分析

利用速率方程分析了转换信号光的频率啁啾,考虑到了外界注入信号光的放大.转换过程中,信号光的注入将会导致了光腔内载流子数发生变化,进而引起激光器输出频率的改变,产生啁啾.研究发现,较大的激光器注入电流可以有效地抑制频率啁啾,较高的注入信号光功率则可以在保证高转换信号消光比的同时抑制频率啁啾.     

All-optical 2R-regeneration and continuous wave to pulsed signal wavelength conversion based on fiber nonlinearity

In this paper, we propose a novel all-optical 2R (re-amplification and re-shaping) regenerator based on inducing nonlinear chirp over a continuous wave probe. The regenerator also performs continuous wave to pulsed wavelength conversion. The chirp is induced in a highly nonlinear fiber by the data modulated pulsed signal that is to be regenerated. Offset filtering is employed at the output of the highly nonlinear fiber to extract the frequencies generated as a result of chirping. The regenerator performance has been evaluated with the help of bit-error-rate plots and eye diagrams at different values of optical signal to noise ratios. Apart from re-shaping and re-amplification, inclusion of the regenerator results in better resilience to amplified spontaneous emission noise.     

Influence of a Fabry–Perot etalon on a chirped optical pulse

Taking into consideration the fact that the output from a Fabry–Perot etalon is formed on the basis of the interference of the multi-reflected beams of the input pulse that enters the etalon, an analytical expression of the output pulse intensity has been derived for an input chirped Gaussian pulse passing through an etalon. Using the expression, the temporal width and the peak power of the output pulse is investigated. Results show that for a given etalon, the chirp factor and the width of the input pulse have intense effects on the width and the peak of the output pulse.     

Experimental study on pulse propagation characteristics at normal dispersion region in dispersion flatted fibers

Pulse propagation characteristics at normal-dispersion region in dispersion-flatted-fibers are experimentally investigated by employing the second-harmonic generation frequency-resolved optical gating (SHG-FROG) method. It is found that the experimental results are consistent with the theoretical prediction. The initial optical pulse with negative chirp is compressed for nonlinear effect in the normal-dispersion fiber, and it evolves into near Gaussian pulse. Temporal width of the optical pulse decreases with the increase of the input power and propagation distance. The output pulse width for small dispersion is less than that for great dispersion at the same input power. The spectrum of the output pulse is still symmetrical about the central wavelength, and is broadened with the increase of input power. The spectral width of the output pulse is much wider than the input spectral width.     

光脉冲在标准单模光纤中演化形成孤子的实验研究

利用二次谐波频率分辨光学门脉冲分析仪从实验上分析研究了具有啁啾的10 GHz光脉冲在不同输入功率下演化形成孤子的规律和特点。实验发现:输入脉冲在光纤中传输3.5个色散长度时,其时间宽度、频率啁啾和时间带宽积都随着输入功率的增加而减小。当输入功率大于一阶孤子功率的理论值时,光脉冲能够演化形成孤子;脉冲在随后传输过程中其宽度基本保持不变,波形、频率啁啾和时间带宽积仍随着传输距离的变化而变化;输入功率越高,形成的一阶孤子脉冲的宽度越窄。当输入功率小于一阶孤子功率的理论值时,输出脉冲的时间宽度随着传输距离的增加而增加,频率啁啾随着传输距离的增加而减小,光脉冲不能演化形成孤子。     

Conversion wavelength and power dependence of an optical delay system utilizing HNLFs and DCF

Conversion wavelength and power dependence of the time delay and output signal quality for an optical delay system consisting of dispersion compensation fiber (DCF) and highly nonlinear fibers (HNLFs) is investigated in this paper. The numerical results show that the time delay generally varies linearly with the conversion wavelength propagating through DCF and changes slightly with the power launched into HNLFs. But it has abrupt change at some values of conversion wavelength or input power level. Output signal quality of the overall system varies significantly with the conversion wavelength and input power level. The reasons behind these results are analyzed. Finally, the input power level is optimized to achieve linearly varying time delay and desirable output signal quality for an optical delay system.     

基于光纤中交叉相位调制的波长转换器研究

波长转换器在未来的全光网络中将起到重要的作用.通过大量的数值仿真,研究了利用色散位移光纤中的自相位调制效应的波长转换器,首次对各参量,包括输入光信号脉冲的峰值功率,连续波的功率,两束光信号的频率间隔,光纤的色散,光纤的长度以及输入信号的比特率对此波长转换器的性能影响进行了数值研究.结果表明,光纤的色散和输入光信号脉冲的功率在这种波长转换器中起重要作用,而且这种波长转换器可以对高达200Gb/s的信号进行转换.     

基于光子晶体光纤中的自相位调制的全光再生

利用高非线性光子晶体光纤中的自相位调制效应产生的超连续谱,理论上推导了超窄脉冲信号的再生机制。分别从频域和时域上形象的解释了脉冲再生的原理,该本再生方法可以适用于OTDM的信号再生。实验上对劣化了的脉冲宽度为1.7ps的携带信息的超窄脉冲信号进行了再生,再生之后的信号峰值均衡,消光比达到了15dB。再生前信号中心波长是1548.2nm,重复频率是9.96872GHz。实验中,在1554nm—1570nm和1530nm—1543nm范围内都可以得到10dB以上的再生质量。同时拟合了信号峰值功率和波长关系,得到的曲线和超连续谱曲线相吻合。     

量子点半导体光放大器波长转换的Q因子特性

为了改善全光波长转换器的转换性能进而提高输出信号质量,研究了波长转换器的Q因子特性。采用牛顿迭代法和四阶龙格库塔法解光场传输方程和跃迁速率方程,分析了输入信号光功率、脉冲宽度、最大模式增益和有源区长度4个因素对全光波长转换器的Q因子特性的影响,并将得到的结果与相同条件下的输出消光比比较。结果表明:增大输入信号光功率,Q因子先增大后减小,并且在-12 d Bm时取得最大值8.819 d B;Q因子随着脉冲宽度的增加而不断下降;增大最大模式增益和有源区长度,Q因子增大。在实现波长转换的基础上,优化各参数数值,得到的Q因子达到16.680 d B,输出信号质量较好。要同时获得高的消光比和Q因子,提高输出信号的质量,必须选取适当的输入信号光功率、脉冲宽度、最大模式增益和有源区长度。     

Performance analysis for an all-optical wavelength converter using four-wave mixing (FWM) in a single mode fiber

An analytical approach is presented to determine the performance of a tunable wavelength converter based on four wave mixing (FWM) in a single mode fiber (SMF) with two pump lasers. The analysis is carried out for an intensity modulated (IM) signal taking into considerations the effects of spectral broadening due to FWM and laser phase noise. The results evaluated at a bit rate of 10 Gb/s show that the signal power is substantially higher at lower values of wavelength separation. For example, for input powers of 10 mW each, wavelength separation of 4 nm between the pump-2 and the input signal, the output converted power is found to be –10 dBm corresponding to wavelength separation of 2 nm between pump-1 and converter signal. The corresponding crosstalk power is found to be –25 dBm at a channel separation of 3 times bit rate.     

Octave spanning supercontinuum in an As₂S₃ taper using ultralow pump pulse energy

An octave spanning spectrum is generated in an As?S? taper via 77 pJ pulses from an ultrafast fiber laser. Using a previously developed tapering method, we construct a 1.3 μm taper that has a zero-dispersion wavelength around 1.4 μm. The low two-photon absorption of sulfide-based chalcogenide fiber allows for higher input powers than previous efforts in selenium-based chalcogenide tapered fibers. This higher power handling capability combined with input pulse chirp compensation allows an octave spanning spectrum to be generated directly from the taper using the unamplified laser output.     

All-Fiber Wavelength Conversion of Ultra-Fast Signal with Enhanced Extinction Ratio Using Stimulated Raman Scattering

We propose a simple method for all-fiber wavelength conversion of ultra-fast signal by means of stimulated Raman scattering. The idea is based on the transference of energy from the signal as pump to a desired signal as first Stokes by stimulated Raman scattering. To minimize the walk-off between two wavelengths, we chose the input signal and the desired output signal wavelengths, equally spaced on opposite sides of the zero dispersion wavelength of the fiber. Based on this assumption, we numerically analyzed the all-fiber wavelength converter for ultra-fast signal with high output power and significantly enhanced output extinction ratio.