Pt掺杂对Mo-Ru-Se簇合物电催化氧还原性能的影响

直接甲醇燃料电池(DMFC)是理想的移动电源,但因金属Pt阴极催化剂的选择性较差,甲醇在阴极产生“混合电位”,导致电池效率降低。抗甲醇氧电还原催化剂可降低“混合电位”,是解决该问题的有效的方法。     

Study of reduced Mo/Al2O3 metathesis catalysts prepared via metal complexes

The Mo/Al₂O₃ catalysts for propene metathesis were prepared both via anchoring Mo complexes of various nuclearities and by conventional method of impregnation. The catalysts from metal complexes were found to be active in metathesis at ambient temperature after reduction with H₂ or CO at 400–500°C. The average oxidation state of Mo in the activated catalysts was determined with regard to oxygen consumption needed for oxidation of the reduced Mo species to Mo⁶⁺.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Cu?Ti?O catalyst for complex purification of gases

Cu–Ti–O catalysts activity in the reactions of complete oxidation of CO and C₄H₁₀, selective catalytic reduction of NO by ammonia, SO₂ oxidation to SO₃, as well as the catalyst resistance to sulfur poisoning were studied. We suggest these catalysts for the combined removal of NO, CO and toxic organics from flue gases.     

Ce改性的Pt/γ-AlO3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-AlO3对于富氢气氛下CO选择氧化反应的催化行为考察了制备条件（共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度）对催化活性的影响．结果表明，在80℃时用共沉积沉淀方法制备的催化剂Pt/γ-AlO3-CP-80对CO氧化反应表现出良好的活性和选择性，CO转化率在120℃时可以达到85％．利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征，分析了Cc的促进作用．     

Pt的氧化状态对甲醇氧化活性的影响

采用NaBH4还原法制备了XC-72碳黑负载的Pt电催化剂,并在化学还原后用H2O2处理部分催化剂以改变Pt的氧化状态,以期改善Pt活性中心上水的离解而提高催化活性.X射线光电子能谱结果表明,经H2O2处理的催化剂含有较多的氧化态Pt.通过循环伏安法和记时电流法考察了经处理和未经处理的催化剂在酸性条件下的甲醇氧化的催化...     

Promotion effect of adsorbed water/OH on the catalytic performance of Ag/activated carbon catalysts for CO preferential oxidation in excess H2

Activated carbon (AC) supported silver catalysts were prepared by incipient wetness impregnation method and their catalytic performance for CO preferential oxidation (PROX) in excess H₂ was evaluated. Ag/AC catalysts, after reduction in H₂ at low temperatures (≤200 °C) following heat treatment in He at 200 °C (He200H200), exhibited the best catalytic properties. Temperature-programmed desorption (TPD), X-ray diffraction (XRD) and temperature-programmed reduction (TPR) results indicated that silver oxides were produced during heat treatment in He at 200 °C which were reduced to metal silver nanoparticles in H₂ at low temperatures (≤200 °C), simultaneously generating the adsorbed water/OH. CO conversion was enhanced 40% after water treatment following heat treatment in He at 600 °C. These results imply that the metal silver nanoparticles are the active species and the adsorbed water/OH has noticeable promotion effects on CO oxidation. However, the promotion effect is still limited compared to gold catalysts under the similar conditions, which may be the reason of low selectivity to CO oxidation in PROX over silver catalysts. The reported Ag/AC-S-He catalyst after He200H₂00 treatment displayed similar PROX of CO reaction properties to Ag/SiO₂. This means that Ag/AC catalyst is also an efficient low-temperature CO oxidation catalyst.     

The Mechanism of Selective NO<Subscript>x</Subscript> Reduction by Hydrocarbons in Excess Oxygen on Oxide Catalysts: IV. Spectrokinetic Characteristics of Intermediate Complexes on the Commercial STK Catalyst

Surface nitrite-nitrate and acetate compounds were detected under conditions of the selective reduction of nitrogen oxides by propane on the STK iron-chromium oxide catalyst using spectrokinetic measurements. The rate of conversion of these complexes under reaction conditions was measured. The resulting values were compared to the rate of the process. The results of this comparison indicated that, at low temperatures (to ∼250°C), the rate of reduction of nitrogen oxides was determined by the interaction of surface nitrite-nitrate complexes with the activated hydrocarbon. The amount of acetate complexes on the surface increased with temperature. A reduction of the surface was also observed as the temperature was increased. The reaction of NO decomposition began on the reduced surface. Nitrogen atoms recombined, and oxygen atoms reacted with the hydrocarbon to form CO₂ in a gas phase. A distinctive feature of the STK catalyst is its ability to form the products of propane mild oxidation and/or oxidative dehydrogenation. From a synergistic standpoint, the STK catalyst is an effective supplier of the activated hydrocarbon, whereas the NTK-10-1 catalyst well activates NO_x. This fact explains the nonadditivity effect observed in the catalytic properties of mechanical mixtures of these catalysts.__________Translated from Kinetika i Kataliz, Vol. 46, No. 4, 2005, pp. 559–568.Original Russian Text Copyright © 2005 by Tret’yakov, Burdeinaya, Zakorchevnaya, Zakirova, Bakhtiyarov, Matyshak, Korchak.     

Low-temperature utilization of CO2 and CH4 by combining partial oxidation with reforming of methane over Ru-based catalysts

Combination of partial oxidation of methane (POM) with carbon dioxide reforming of methane (CRM) has been studied over Ru-based catalysts at 550 ℃. POM, CRM and combined reaction were performed over 8wt%Ru/γ-Al2O3 and the results show that both POM and CRM contribute to the combined reaction, between which POM plays a more important role. Moreover, the addition of Ce to Ru-based catalyst results in an improvement in the activity and CO selectivity under the adopted reaction conditions. The Ce-doped catalyst was characterized by N2 adsorption-desorption, SEM, XRD, TPR, XPS and in situ DRIFTS. The mechanism has been studied by in situ DRIFTS together with the temperature distribution of catalyst bed. The mechanism of the combined reaction is more complicated and it is the combination of POM and CRM mechanisms in nature. The present paper provides a new catalytic system to activate CH4 and CO2 at a rather low temperature.     

Selective oxidation of CO in excess hydrogen on copper—cerium-containing catalysts

Selective oxidation of CO that is in mixtures enriched in H₂ was studied to investigate catalytic properties of the 0.5—80% CuO/Ce_0.7Zr_0.3O₂ system. The catalysts were prepared by the combined decomposition of copper, cerium, and zirconyl nitrates at 300 °C. The systems studied are active and stable under mild conditions of the process (80—160 °C) and at high space velocities (to 100000 h^–1) of the reaction mixture (2% CO, 1% O₂, 40—50% H₂). With an increase in the CuO content in the catalysts up to 20%, the degree of CO removal achieves 60% (120 °C and V = 35000 h^–1) and further does not change appreciably. The contribution of oxygen participation into CO oxidation is virtually independent of the copper concentration in the sample and ranges from 65 to 75%. The dependences of the Arrhenius equation parameters for CO and H₂ oxidation on the catalyst composition were determined, which makes it possible to calculate the conversion of reactants and selectivity of CO conversion under the specified conditions of the process. The addition of CO₂ and H₂O (12—15%) to the reaction mixture decreases the catalyst activity and simultaneously increases the selectivity of CO oxidation to 100%. It is shown by the TPR and X-ray diffraction methods that the combined decomposition of the starting Cu²⁺, Ce³⁺, and ZrO²⁺ nitrates produces solid solutions of oxides with a high content of CuO. The reductive pre-treatment of fresh samples of the studied catalysts results in the destruction of the solid solution and formation of highly dispersed Cu particles on the surface of Ce—Zr—O. These particles are active in CO oxidation.     

ZrO2改性对Pt/Al2O3催化剂上CO氧化性能的影响

用流动反应法、TPR和TPD－MS等技术研究了Pt／Al2O3催化剂掺杂ZrO2体系上CO的催化氧化反应、氧物种的还原及脱出－恢复行为．结果表明，掺杂ZrO2有利于催化剂上氧物种的脱出－恢复，从而促进CO氧化活性及表面活泼氧物种与氢的反应．并用催化剂集团结构适应理论对结果作出了解释．     

Property and structure of various platinum catalysts for low-temperature carbon monoxide oxidations

The oxidation of carbon monoxide (CO) has received more attention in the last two to three decades owing to its importance in different fields. To control this CO pollution, catalytic converters have been investigated. Different types of catalysts have been used in a catalytic converter for CO emission control purposes. Platinum (Pt)-based noble metal catalysts show great potential for CO oxidation in catalytic converters with high thermal stability and tailoring flexibility. Pt metal catalysts modified with promoters such as alkali metals and reducible metal oxides have received great attention for their superior catalytic activities in CO oxidation. Temperature, close environment of the catalyst, and chemical composition in the surface layer of the catalyst have a huge effect on the active phase dispersion and O₂ adsorption capacity of the Pt metal catalysts. The main difference in activities of Pt metal catalyst for CO oxidation in O₂ or H₂ atmosphere has found. The addition of supports in Pt metal catalysts has improved their performances and reduced their cost. These improvement strongly depends on the surface structure, morphology, number of active sites, and various Pt-O interactions. Many research articles have already been published in CO oxidation over Pt metal catalysts, but no review article dedicated to CO oxidation is available in the literature.     

The influence of the active component and support nature, gas mixture composition on physicochemical and catalytic properties of catalysts for soot oxidation

Physicochemical and catalytic properties of compositions Fe(Ce)–Mn–O/support (gamma-, theta-, alpha-Al₂O₃, SiO₂ as the support) and Pt/CeO₂/theta-Al₂O₃ for oxidation of soot were characterized. It was established that the phase composition of the initial catalysts depended mainly on the nature of the active component and preparation conditions. Non-isothermal treatment of the soot–catalyst compositions at the temperature up to 1000 °C resulted in a change in the phase composition depending mainly on the final treatment temperature. The catalyst surface area was determined by the support nature. It was established that catalyst activities for oxidation of soot are determined by both catalyst nature and composition of gas mixture. The process of the soot oxidation is thought to involve oxygen from the catalyst surface. The higher proportion of weakly bound surface oxygen, the higher was the catalyst activity. An increase in the oxygen concentration from 5% O₂/N₂ to 15% O₂/N₂ is shown to lead to a decrease of the temperature of the soot oxidation. The influence of the oxygen concentration on the process of soot oxidation becomes weaker in the presence of water vapor. Results showed that the presence of NO in the gas mixture favors a decrease in the oxidation temperature of the soot, the higher being the nitrogen oxide concentration, the more pronounced effect. Introduction of SO₂ in amount of 50 ppm in the gas mixture has no noticeable effect on the process of the soot oxidation. Among the catalysts under study, Fe–Mn–K–O/gamma-Al₂O₃ is most effective to oxidation of the soot at otherwise identical conditions.     

Highly Ordered Mesoporous Cobalt-Copper Composite Oxides for Preferential CO Oxidation

Highly ordered mesoporous cobalt-copper composite oxides were prepared by the nanocasting method with various Co and Cu ratios. The catalysts obtained were characterized by X-ray diffraction, N₂ adsorption–desorption, H₂-temperature programmed reduction, CO-temperature programmed desorption and X-ray photoelectron spectroscopy. All of the catalysts had uniform mesopores and high surface areas. The distinct catalytic properties of these well-characterized mesoporous materials were demonstrated for preferential CO oxidation. It is found that the mesoporous cobalt-copper composite oxides, exhibited the higher catalytic activity for CO conversion and selectivity compared with the mesoporous Co₃O₄ and mesoporous CuO. Among these catalysts the mesoporous cobalt-copper catalyst with Co:Cu molar ratio of 70:30, shows the best catalytic activity and the broadest operating temperature “window” for the high CO conversion in the range of 125–200^oC. The higher catalytic activity was attributed to the higher CO adsorption and oxygen vacancies.     

Influence of MgO contents on silica supported nano-size gold catalyst for carbon monoxide total oxidation

A series of nano-size gold catalysts were prepared by deposition-precipitation method using silica material promoted with different amounts of MgO as the carrier. The influences of MgO addition on the structure and property of the nano-size gold catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), O2 temperature-programmed desorption (O2-TPD), and inductively coupled with plasma atomic emission spectroscopy (ICP-AES) techniques. The total oxidation of CO was chosen as the probe reaction. The results suggest that for the gold catalysts supported on the silica material after MgO modification, the size of the gold particles is pronouncedly reduced, the oxygen mobility is enhanced, and the catalytic activity for low-temperature CO oxidation is greatly improved. The gold catalyst modified by 6 wt% MgO (Mg/SiO2 weight ratio) shows higher CO oxidation activity, over which the temperature of CO total oxidation is lower about 150 K than that over the silica directly supported gold catalyst.     

The effect of hydrogen reduction of α-MnO2 on formaldehyde oxidation: The roles of oxygen vacancies

A series of α-MnO₂ catalysts with various Mn valence states were treated by hydrogen reduction for different periods of time. Their catalytic capacity for formaldehyde (HCHO) oxidation was evaluated. The results indicated that hydrogen reduction dramatically improves the catalytic performance of α-MnO₂ in HCHO oxidation. The α-MnO₂ sample reduced by hydrogen for 2 h possessed superior activity and could completely oxidize 150 ppm HCHO to CO₂ and H₂O at 70 °C. Multiple characterization results illustrated that hydrogen reduction contributed to the production of more oxygen vacancies. The oxygen vacancies on the catalyst surface enhanced the adsorption, activation and mobility of O₂ molecules, and thereby enhanced HCHO catalytic oxidation. This study provides novel insight into the design of outstanding MnO_x catalysts for HCHO oxidation at low temperature.     

Removal of CO from reformed fuels by selective methanation over Ni-B-Zr-Oδ catalysts

The Ni-B-Oδ andNi-B-Zr-Oδ catalysts were prepared by the method of chemical reduction, and the deep removal of CO by selective methanation from the reformed fuels was performed over the as-prepared catalysts. The results showed that zirconium strongly influenced the activity and selectivity of the Ni-B-Zr-Oδ catalysts. Over the Ni-B-Oδ catalyst, the highest CO conversion obtained was only 24.32% under the experimental conditions studied. However, over the Ni-B-Zr-Oδ catalysts, the CO methanation conversion was higher than 90% when the temperature was increased to 220 oC. Additionally, it was found that the Ni/B mole ratio also affected the performance of the Ni-B-Zr-Oδ catalysts. With the increase of the Ni/B mole ratio from 1.8 to 2.2, the CO methanation activity of the catalyst was improved. But when the Ni/B mole ratio was higher than 2.2, the performance of the catalyst for CO selective methanation decreased instead. Among all the catalysts, the Ni29B13Zr58Oδ catalyst investigated here exhibited the highest catalytic performance for the CO selective methanation, which was capable of reducing the CO outlet concentration to less than 40 ppm from the feed gases stream in the temperature range of 230–250 oC, while the CO2 conversion was kept below 8% all along. Characterization of the Ni-B-Oδ and Ni-B-Zr-Oδ catalysts was provided by XRD, SEM, DSC, and XPS.     

Catalytic properties of oxides in vapor phase oxidation of acetone

The temperature dependences of the rate of oxidation of acetone vapors by oxygen on oxide surface catalysts: V₂O₅, Co₃O₄., MoO₃ and TiO₂ (rutile), and the industrial catalyst VKSh were determined. A series of the catalytic activity of the above surface catalysts was established. The relationship between the catalytic properties of the oxides in the oxidation of acetone and their redox and acid-base characteristics was analyzed. The catalytic activity of the oxides in the oxidation reaction of acetone and methanol were compared.Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 24, No. 1, pp. 114–117, January–February, 1988.     

钙钛矿型La1+X/2Sr1-x/2Co1-xCuxO3催化CO氧化活性与表征

The catalytic activity and the reactive properties of perovskite-type oxides catalysts La(1+x/2)Sr(1-x/2)Co1-xCuxO3 for CO oxidation reaction were investigated. Results showed that the catalytic activity for CO oxidation reached to a maximum when x＝0.4. The temperature for complete CO oxidation under atmospheric and experimental conditions was 168℃. According to the stoicheometry of catalyst, all catalysts were oxygen defect compounds. The active oxygen species on this catalyst was the adsorbed oxygen which was adsorbed on the surface lattice oxygen defect. It was also found that Co4+ existed in the catalysts and the sufrace active oxygen species was caused by the Co4+. It was concluded that CO oxidation reaction on this catalyst was carried out by the valence change between Co3+ and Co4+ which was adjusted by the adsorbed oxygen.     

The Effect of Nb Loading on Catalytic Properties of Ni/Ce0.75Zr0.25O2 Catalyst for Methane Partial Oxidation

In this study,the effect of Nb loading on the catalytic activity of Ce_(0.75)Zr_(0.25)O_2-supported Ni catalysts was studied for methane partial oxidation.The catalysts were characterized by BET,H_2 chemisorption,XRD,TPR,TEM and tested for methane partial oxidation to syngas in the temperature range of 400-800℃at atmospheric pressure.The results showed that the activity of methane partial oxidation on the catalysts was apparently dependent on Nb loading.It seemed that the addition of Nb lowered the catalytic activity for methane partial oxidation and increased the extent of carbon deposition. This might be due to the strong interaction between NiO and Nb-modified support and reduction of surface oxygen reducibility.