III-V族化合物半导体材料的高能重离子辐照效应

用高能（５００ＭｅＶ）Ｎｅ离子束对ＧａＡｓ和ＩｎＰ进行了辐照，用ＭｏｎｔｅＣａｒｌｏ模拟、正电子湮没谱学以及红外光谱研究了辐照产生的缺陷特性．结果表明，在未辐照的样品中存在单空位，经辐照后，可在样品中产生单空位；当剂量较大时，还会形成双空位甚至尺寸较大的空洞．红外光谱测量发现，在辐照后的ＧａＡｓ样品中有非晶区形成．此外，辐照在样品中还产生了反位缺陷ＧａＡｓ和ＩｎＰ以及受主杂质ＺｎＩｎ．对经１０１４ｉｏｎｓ／ｃｍ２剂量辐照的ＩｎＰ进行了光学实验，在辐照后的ＩｎＰ材料中发现了亚稳态中心． Both GaAs and InP were irradiated by high energy (500 MeV) Ne ions. The Monte Carlo simulation, positron annihilation and IR spectroscopy were used to study the radiation induced defects. The result showed that monovacancies existed in as grown samples, but more monovacancies were introduced, after Ne ions irradiation, and with increasing radiation dose, divacancies were formed, and eventually large voids were observed. The IR measurement for irradiated GaAs samples confirmed the...     

浅杂质注入LEC半绝缘GaAs γ射线辐照缺陷

用深能级瞬态谱（ＤＬＴＳ）和恒温电容瞬态等技术研究了浅杂质注入ＬＥＣ半绝缘ＧａＡｓ的γ射线辐照缺陷。在Ｂｅ－Ｓｉ共注的ＬＥＣ半绝缘ＧａＡｓ中，γ射线辐照引入一电子陷阶Ｅ₂，并且大大增强了原有的Ｅ₀₁（０．２９８）和Ｅ₀₂（０．３４１）等缺陷，同时明显地瓦解了原有的少子陷阱Ｈ₀₃。在单纯注Ｓｉ的ＬＥＣ半绝缘ＧａＡｓ中，γ射线辐阳引进了Ｅ＇₀₁（０．２１６），Ｅ＇₀₂（０．３４１），Ｅ＇₂，Ｅ＇₄和Ｅ＇₅（０．６０８）等缺陷。其中Ｅ₀₁和Ｅ＇₀₁是新发现的和γ辐照有关的ＧａＡｓ缺陷。和低阻衬底同质外延ＧａＡｓ相比，Ｂｅ－Ｓｉ共注ＬＥＣ半绝缘ＧａＡｓ具有较低的γ射线辐照缺陷引入率，与此相反，单纯注Ｓｉ的ＬＥＣ半绝缘ＧａＡｓ具有较高的γ射线辐照缺陷的引入率。 关键词：     

1MeVSi~＋衬底加温注入Al＿（0．3）Ga＿（0．7）As／GaAs超晶格和GaAs的晶格损伤研究

用卢瑟福背散射／沟道技术研究了１ＭｅＶＳｉ￣＋在衬底加温和室温下以不同剂量注入Ａｌ＿（０．３）Ｇ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ后的晶格损伤。在衬底加温下，观察到Ａｌ＿（０．３）Ｇａ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ都存在一个动态退火速率与缺陷产生速率相平衡的剂量范围，以及两种速率失去平衡的临界剂量。超晶格比ＧａＡｓ更难以损伤，并且它的两种速率失去平衡的临界剂量也大于ＧａＡｓ中的相应临界剂量，用热尖峰与碰撞模型解释了晶格损伤积累与注入剂量和衬底温度的关系。用ＣＮＤＯ／２量子化学方法计算了ＧａＡｓ和Ａｌ＿ｘＧａ＿（１－ｘ）Ａｓ中化学键的相对强度，并根据计算结果解释了注入过程中Ａｌ＿（０．３）Ｇａ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ中晶格损伤程度的差别。     

Te—Se—I玻璃及添加As和Ge元素的结构,性能与量子化学计算研究

用自洽场离散变分Ｘα（ＳＣＦ－Ｘα－ＤＶ）量子化学计算方法研究了Ｔｅ－Ｓｅ－Ｉ玻璃及添加Ａｓ和Ｇｅ元素的体系，讨论了结构、性能与化学键之间的关系。计算表明离子键和共价键强度的次序都是Ｇｅ－Ｓｅ〉Ａｓ－Ｓｅ〉Ｔｅ－Ｓｅ，与相应的玻璃转变温度的实验结果一致。含有一配位碘原子的Ｔｅ－Ｉ键比含有二配位碘原子的Ｔｅ－Ｉ键强。Ａｓ－Ａｓ和Ａｓ－Ｉ键比两类Ｔｅ－Ｉ键都强。较强的Ａｓ－Ａｓ和Ａｓ－Ｉ键取代较弱的Ｔ     

砷化镓探测器的镉上中子辐照改性

介绍反应堆镉上中子辐照改性的掺铬砷化镓（ＧａＡｓ：Ｃｒ）和本征砷化镓（ＧａＡｓ）光电导探测器，研究了探测器的响应时间、粒子灵敏度及输出电流随镉上中子辐照改性注量和施加偏压的变化关系。     

Ga2Se3／ZnSe异质结分子束外延生长过程中ZnGa2Se4外延层的形成

首次在（１００）ＧａＡｓ衬底上成功地生长出ＺｎＧａ２Ｓｅ４外延薄膜。用分子束外延技术在１００ＧａＡｓ衬底上制备Ｇａ２Ｓｅ３／ＺｎＳｅ异质结时，用５４０℃以上的温度生长出ＺｎＧａ２Ｓｅ外延层。     

Zn/GaAs(110)系统的表面弛豫及其对费密能级钉扎的影响

在紧束缚近似下，利用自洽总能计算给出了Ｚｎ／ＧａＡｓ（１１０）系统的表面几何结构．证明了低覆盖下Ｚｎ／ＧａＡｓ（１１０）表面弛豫是一普遍现象，它对准确地描述费密能级钉扎位置十分重要．由于吸附Ｚｎ原子的高局域ｓ轨道与表面Ｇａ原子ｓｐ^３悬挂键轨道的杂化，使成键态位于能隙中距价带顶０.７３ｅＶ处．进一步给出了与其它元素吸附和清洁ＧａＡｓ（１１０）表面的理论与实验结果之比较     

GaAs衬底上生长的GaInP_2外延单晶薄膜的杂质污染研究

各种外延技术已被用来在ＧａＡｓ衬底上生长ＧａｘＩｎ１－ｘＰ外延单晶薄膜（ＧａＩｎＰ２／ＧａＡｓ）．很多文献认为,在ＧａＩｎＰ２／ＧａＡｓ生长过程中会被Ｃ杂质污染．我们用高灵敏的ＣＡＭＥＣＡＩＭＳ４Ｆ型二次离子质谱仪直接测量的结果表明,污染ＧａＩｎＰ２／ＧａＡｓ的微量杂质是Ｓｉ,而不是Ｃ．由ＧａＩｎＰ２／ＧａＡｓ在１．１７ｅＶ附近的光致发光峰的峰值随激发强度的变化形状表明了它应属于施主－受主对复合发光．进一步分析表明,施主为处在Ｇａ格位上的Ｓｉ杂质（ＳｉＧａ）,受主为Ｇａ空位（ＶＧａ）．     

低压－金属有机物汽相外延生长的Ga＿（1－x）In＿xAs／InP激光器中深能级的研究

应用深能级瞬态谱（ＤＬＴｓ）技术详细研究低压－金属有机物汽相外延（ＬＰ－ＭＯＶＰＥ）生长的Ｇａ＿（０．４７）Ｉｎ＿（０．５３）Ａｓ／Ｉｎｐ量子阱、宽接触和质子轰击条形异质结激光器中的深能级。样品的ＤＬＴＳ表明，在宽接触激光器的ｉ－Ｇａ＿（０．４７）Ｉｎ＿（０．５３）Ａｓ有源层里观察到Ｈ１（Ｅ＿ｖ＋０．０９ｅＶ）和Ｅ１（Ｅ＿ｃ－０．３５ｅＶ）陷阱，它们可能分别与样品生长过程中扩散到ｉ－Ｇａ＿（０．４７）Ｉｎ＿（０．５３）Ａｓ有源层的Ｚｎ和材料本身的原生缺陷有关。而条形激光器的ｉ－Ｇａ＿（０．４７）Ｉｎ＿（０．５３）Ａｓ有源层的Ｈ２（Ｅ＿ｖ＋０．１１ｅＶ）和Ｅ２（Ｅ＿ｖ－０．４２ｅＶ）陷阱则可能是Ｈ１和Ｅ１与质子轰击引起的损伤相互作用的产物。     

荧光XAFS研究Si可稀浓度杂质的区域结构

荧光ＸＡＦＳ研究Ｓｉ晶体中等电子，缺电子和富电子杂质原子的区域环境结构。结果表明杂质原子的电子构型决定了杂质原子对Ｓｉ区域晶格形变的影响。相对于共价键长ＲＳｉ－Ｓｉ（０．２４０ｎｍ）来说，富电子杂质Ａｓ导致Ｓｉ晶格在Ｓｉ（１１１）方向的ＲＡｓ－Ｓｉ键长产生０．００４ｎｍ的反应增长，等电子杂质Ｇｅ的Ｒ－Ｇｒｅ－Ｓｉ和缺电子杂质Ｇａ和ＲＧａ－Ｓｉ键长收缩０．００２ｎｍ。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.