CrOx-CeO2二元氧化物表面NO的NH3催化还原反应机理

利用原位漫反射红外光谱法研究了473 K下在CrOx-CeO₂二元氧化物表面NO的NH₃催化还原反应的机理。研究了CrO-CeO₂二元氧化物表面在反应过程中的表面吸附物种。为了更加清晰的了解反应过程, 在SCR反应过程中分别切断NH₃和NO的气流, 并采集了所生成的原位漫反射红外光谱图, 通过研究以上结果得出结论:当前状态下的SCR反应过程可能服从E-R机理。     

CrOx-CeO2二元氧化物表面NO的NH3催化还原反应机理

利用原位漫反射红外光谱法研究了473 K下在CrOx-CeO2二元氧化物表面NO的NH3催化还原反应的机理。研究了CrOx-CeO2二元氧化物表面在反应过程中的表面吸附物种。为了更加清晰的了解反应过程,在SCR反应过程中分别切断NH3和NO的气流,并采集了所生成的原位漫反射红外光谱图,通过研究以上结果得出结论:当前状态下的SCR反应过程可能服从ER机理。     

Phase Formation Study of Alkaline Earth-doped Lanthanum Chromites

In this paper the influence of alkaline-earth admixtures on the synthesis of lanthanum chromites of La_1–xM_xCrO₃ (x=0; 0.3; M=Ca, Sr, Ca+Sr) type was studied. The formation mechanism as well as the phase composition evolution, under non-isothermal and isothermal conditions, were investigated by thermal analysis and X-ray diffraction. The structure of the compounds and of the solid solutions formed depends on the solute type by means of the structural distortion induced. The crystallinity of the chromites obtained is obviously influenced by both the temperature and the thermal treatment plateau. This revised version was published online in August 2006 with corrections to the Cover Date.     

Kinetics of formation of barium tungstate in equimolar powder mixture of BaCO<Subscript>3</Subscript> and WO<Subscript>3</Subscript>

The formation of Barium monotungstate (BaWO₄) particles in equimolar powder mixtures of BaCO₃ and WO₃ was examined under isothermal and non-isothermal conditions upon heating in air at 25–1200 °C, using thermogravimetry. Concurrence of the observed mass loss (due to the release of CO₂) to the occurrence of the formation reaction was evidenced. Accordingly, the extent of reaction (x) was determined as a function of time (t) or temperature (T). The x–t and x–T data thus obtained were processed using well established mathematical apparatus and methods, in order to characterize nature of reaction rate-determining step, and derive isothermal and non-isothermal kinetic parameters. Moreover, the reaction mixture quenched at various temperatures (600–1,000 °C) in the reaction course was analyzed by various spectroscopic and microscopic techniques, for material characterization. The results obtained indicated that the reaction rate may be controlled by unidirectional diffusion of WO₃ species across the product layer (BaWO₄), which was implied to form on the barium carbonate particles. The isothermally determined activation energy (118–125 kJ/mol) was found to be more credible than that (245 kJ/mol) determined non-isothermally.     

Phase stability of La1−xCaxCrO3−δ in oxidizing atmosphere

The chemical stability of perovskite-type La_1−xCa_xCrO_3−δ (x=0.1, 0.2, 0.3) in high oxygen partial pressure, P_O2, was investigated with three methods: thermogravimetry, XRD analysis, and thermodynamic calculation. The second phase, CaCrO₄ was observed by XRD analysis on the powder equilibrated in high P_O2. Thermogravimetry under fixed temperatures sensitively detected the segregation of the second phase in the form of oxygen incorporation, because oxidation of chromium ion accompanies the segregation. The second phase tended to appear in high P_O2 and at low temperature. The single-phase regions of La_1−xCa_xCrO_3−δ obtained from the two experimental methods well agreed with each other. The results of thermodynamic calculation on the assumption of ideality of the solid solution also agreed with the experimental results. These results suggested the sufficient chemical stability of La_1−xCa_xCrO_3−δ in high P_O2 concerning the application to an interconnector of high-temperature solid oxide fuel cells; for example, La_0.7Ca_0.3CrO_3−δ is stable at 1273 K in air.     

Thermal decomposition and creation of reactive solid surfaces

Three chromia precursors, namely CrO₃, (NH₄)₂Cr₂O₇ and chromia gel, were subjected to thorough thermal analysis by means of TG and DTA. The thermal decomposition products obtained by calcination of these precursors at various temperatures (150–500°) for 5 h were investigated by infrared and X-ray techniques. The results obtained allowed a thorough physicochemical characterization of the intermediate steps and products throughout the thermal decomposition.     

Analysis of magnetic and structural phase transition behaviors of La1−xSrxCrO3 for preparation of phase diagram

The phase transition behavior of perovskite-type compounds, La_1−xSr_xCrO₃, was investigated by differential scanning calorimetry (DSC), dilatometry, dc magnetic susceptibility measurement and X-ray diffraction analysis. Both second-order magnetic phase transition from antiferromagnetic to paramagnetic and first-order structural phase transition from orthorhombic to rhombohedral were observed in the DSC or dilatometric curve of every specimen. The temperatures of both these magnetic and structural phase transitions decreased linearly with an increase in Sr content. The structural phase transition temperature of La_1−xSr_xCrO₃ with x less than 0.11 is higher than the magnetic phase transition temperature; however, a larger decrease in structural phase transition temperature than in magnetic phase transition temperature was observed with an increase in Sr content, resulting in a structural phase transition temperature lower than the magnetic phase transition temperature for La_1−xSr_xCrO₃ with x of more than 0.12. It was also observed that the heat of absorption of the structural phase transition decreased with an increase in x. In the dependence of dc magnetic susceptibility on temperature, variations by not only magnetic but also structural phase transitions were observed. It was also revealed that thermal expansion coefficient is affected not only by structural phase transition but also magnetic phase transition. Magnetic and structural phase diagram of La_1−xSr_xCrO₃, suggesting the existence of two Sr contents and temperatures at which triple phases coexist, was proposed.     

CrOx/SiO2催化剂上丙烷在CO2气氛中脱氢反应的研究

采用XRD、UV-vis DRS、ESR和微分吸附量热等技术,考察了铬担载量分别为2.5、5和10wt%的CrO_x/SiO₂催化剂的结构、表面性质和氧化还原性能。结果表明,催化剂表面上存在多种Cr的氧化态和聚集形式。随着Cr担载量从2.5wt%到10wt%的逐渐增大,催化剂表面占主导地位的Cr物种由CrO₃单体转为多聚CrO₃和Cr₂O₃晶相。在CO₂气氛中催化剂对丙烷转化率和丙烯选择性的大小顺序为2.5wt%CrO_x/SiO₂>5wt%CrO_x/SiO₂>10wt%CrO_x/SiO₂,反应过程中的原位ESR和UV-visDRS测定结果表明,催化剂表面的反应活性中心为Cr⁵⁺,Cr⁵⁺可由催化剂预处理过程中Cr³⁺的氧化及丙烷反应过程中CrO₃单体的还原产生,在反应中CO₂可使Cr³⁺重新氧化为Cr⁵⁺.     

The effect of experimental methods and measurement conditions on values of the kinetic parameters of [Co(NH3)6]2(C2O4)3·4H2O

Using the thermal decomposition of [Co(NH₃)₆]₂(C₂O₄)₃·4H₂O as a basis, the paper presents results which show how computed values of kinetic parameters are influenced by experimental conditions (ambient atmosphere, sample mass, linear heating rate) when using the non-isothermal methods and the Coats-Redfern (CR) modified equation. It also illustrates the influence of the experimental methods i.e. non-isothermal and isothermal (conventional) methods and also a quasiisothermal-isobaric one which can be recognised as equivalent to Constant Rate Thermal Analysis (CRTA). The results obtained have confirmed the significant influence of the experimental parameters as well as that of the experimental method used on the estimated values of kinetic parameters. The correlation between activation energy (E) and sample mass (m) or heating rate (β) is generally of a linear nature:E=a+bx     

Formation of Cr(II) Species in the H2/CrO3 System. Parameter control

The thermal behaviour of CrO₃ on heating up to 600°C in dynamic atmospheres of air, N₂ and H₂ was examined by thermogravimetry (TG), differential thermal analysis (DTA), IR spectroscopy and diffuse reflectance spectroscopy (DRS). The results revealed three major thermal events, depending to different extents on the surrounding atmosphere: (i) melting of CrO₃ near 215°C (independent of the atmosphere), (ii) decomposition into Cr₂(CrO₄)₃ at 340–360°C (insignificantly dependent), and (iii) decomposition of the chromate into Cr₂O₃ at 415–490°C (significantly dependent). The decomposition CrO₃ → Cr₂(CrO₄)₃ is largely thermal and involves exothermic deoxygenation and polymerization reactions, whereas the decomposition Cr₂(CrO₄)₃ → Cr₂O₃ involves endothermic reductive deoxygenation reactions in air (or N₂) which are greatly accelerated and rendered exothermic in the presence of H₂. TG measurements as a function of heating rate (2–50°C min⁻¹) demonstrated the acceleratory role of H₂, which extended to the formation of Cr(II) species. This could sustain a mechanism whereby H₂ molecules are considered to chemisorb dissociatively, and then spillover to induce the reduction. DTA measurements as a function of the heating rate (2–50°C min⁻¹) helped in the derivation of non-isothermal kinetic parameters strongly supportive of the mechanism envisaged. This revised version was published online in August 2006 with corrections to the Cover Date.     

Effect of strontium substitution on the activity of La2?xSrxNiO4 (x = 0.0–1.2) in NO decomposition

The aim of this work is to study the effect of Sr substitution on the redox properties and catalytic activity of La_2−x Sr _x NiO₄ (x = 0.0–1.2) for NO decomposition. Results suggest that the x = 0.6 sample shows the highest activity. The characterization (TPD, TPR, etc.) of samples indicates that the x = 0.6 sample possesses suitable abilities in both oxidation and reduction, which facilitates the proceeding of oxygen desorption and NO adsorption. At temperature below 700°C, the oxygen desorption is difficult, and is the rate-determining step of NO decomposition. With the increase of reaction temperature (T > 700°C), the oxygen desorption is favorable and, the active adsorption of NO on the active site (NO + V _o + Ni²⁺ → NO⁻-Ni³⁺) turns out to be the rate-determining step. The existence of oxygen vacancy is the prerequisite condition for NO decomposition, but its quantity does not relate much to the activity. Supported by the National Hi-Tech Research and Development Program of China (863 Program)(Grant No. 2004CB 719502) and the National Natural Science Foundation of China (Grant No. 20177022)     

Chemical stability of La1−xSrxCrO3 in oxidizing atmospheres

The single-phase region of La_1−xSr_xCrO₃ (x=0.1, 0.2, 0.3) was precisely determined as a function of temperature, P_O2 and Sr content. The powders with the nominal composition of La_1−xSr_xCrO₃ were equilibrated under various conditions, and then identified by XRD analyses. To confirm the equilibration, two independent experiments were performed for each composition observing (i) the precipitation of the second phase from a single-phase solid solution, and (ii) the formation of the single phase from the constituent oxides. Two kinds of second phases, SrCrO₄ and an unknown phase, were observed depending on the conditions. The second phases tended to appear at low temperature, in high P_O2 and with a large Sr content. The single-phase regions obtained via the two equilibration routes were in good agreement with each other. The thermodynamic calculations on the supposition of ideality of the solid solution essentially reproduced the experimental results. When this material is used as the interconnects of solid oxide fuel cells, much attention should be paid to its relatively narrow solubility range of Sr; for example, the solubility limit is approximately 0.1 under a typical cathode-side condition (1273 K, air).     

A kinetic analysis of thermal decomposition of polyaniline/ZrO<Subscript>2</Subscript> composite

Synthesis, characterization and thermal analysis of polyaniline (PANI)/ZrO₂ composite and PANI was reported in our early work. In this present, the kinetic analysis of decomposition process for these two materials was performed under non-isothermal conditions. The activation energies were calculated through Friedman and Ozawa-Flynn-Wall methods, and the possible kinetic model functions have been estimated through the multiple linear regression method. The results show that the kinetic models for the decomposition process of PANI/ZrO₂ composite and PANI are all D₃, and the corresponding function is ƒ(α)=1.5(1−α)^2/3[1−(1-α)^1/3]−1. The correlated kinetic parameters are E _a=112.7±9.2 kJ mol⁻¹, lnA=13.9 and E _a=81.8±5.6 kJ mol⁻¹, lnA=8.8 for PANI/ZrO₂ composite and PANI, respectively.     

A kinetic study of the thermal degradation of 3-methylaminopropylamine inside AlPO<Subscript>4</Subscript>-21

Kinetics of the thermal decomposition of 3-methylaminopropylamine which was used as a structure-directing agent in the synthesis of AlPO₄-21 has been studied under isothermal and non-isothermal conditions. The decomposition is a single-step reaction occurring in the 573–663 K range. It is a phase-boundary-controlled process, described by the ‘F2/3, R3’ kinetic model. The activation energy values obtained under the non-isothermal and isothermal conditions lie in the 173–151 kJ mol^–1 range.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

Influence of heat treatment conditions on the physicochemical and catalytic properties of a chromium-containing catalyst for tetrachloroethylene hydrofluorination to pentafluoroethane

The physicochemical properties of coprecipitated 95% Cr₂O₃-5% Al₂O₃ oxide systems obtained by heat treatment of the precursor in nitrogen and air between 110 and 600°C and their influence on the catalytic activity in tetrachloroethylene hydrofluorination were studied by thermal and X-ray diffraction analyses, diffuse reflectance spectroscopy, and specific surface are measurements. The CrO_1.9 compounds are more active than CrO_1.5, but their preparation in the finely divided state is difficult because of the high exothermicity of the oxidation stage, which results in the decomposition of the oxides CrO_1.9 and CrO_1.5 followed by the crystallization and sintering of the decomposition products. Fine-powder and highly active chromium-containing oxides with CrO_1.9 stoichiometry can be obtained by two-stage heating of hydroxides first in nitrogen and then in air at comparatively low temperatures.     

Preparation, characterization and thermolysis of metal nitrate complexes with 4,4’-bipyridine

Two bis(bipyridine) polymeric metal nitrate complexes with 4,4’-bipyridine of simple formula like [M(bipy)₂](NO₃)2⋅xH₂O (where M=Co, Ni and Cu; x=4, 2 and 0, respectively) have been prepared and characterized. Their thermal decomposition has been undertaken using simultaneous TG-DTG-DTA and DSC in nitrogen atmosphere and non-isothermal TG in air atmosphere. Isothermal TG has been performed at decomposition temperature range of the complexes to evaluate the kinetics of decomposition by applying model-fitting as well as isoconversional method. Possible mechanistic pathways have also been proposed for the thermolysis. Ignition delay measurements have been carried out to investigate the response of these complexes under the condition of rapid heating.     

Reactivity investigations of some chosen peroxo-vanadium(V), manganese(III) and chromium(VI) compounds

An interpretative account of the results of reactions in aqueous medium of a highly peroxygenated vanadium(V) complex, K [V(O_{2 3}]·3H₂O, with different organic and inorganic substrates is presented. The reactions were monitored by solution EPR spectroscopy and isolation of products at different stages of the reactions. Redox reactions between diperoxide, K[VO(O₂)₂(H₂O)] and VOSO₄ were conducted. The results of the investigation suggest that secondary oxygen exchange-reaction occurs which not only depends on but also utilises the intermediates in the primary reaction during diperoxovanadate-dependent oxidation of VOSO₄. In an interesting reactiontris(acetylacetonato)-manganese(III), Mn(acac)₃, on being reacted with a hydrogen peroxide adduct, KF·H₂O₂, and bpy and phen afforded crystalline [Mn(acac)₂(bpy)] and [Mn(acac)₂(phen)], respectively. The X-ray structural analysis of [Mn(acac)₂(phen)] showed that the compound crystallised in orthorhombic space groupPbcn. The structure consists of a pseudooctahedral Mn(II) ion being bound to two acac⁻(C₅H₅O ₂ ⁻ ) and a phen ligand with the molecule lying on two-fold axis. Reactivity profiles of two new chromium(VI) reagents viz., pyridinium fluorochromate, C₅H₅NH[CrO₃F] (PFC), and quinolinium fluorochromate C₉H₇NH [CrO₃F] (QFC), have been presented. The compounds are capable of acting as both electron-transfer and oxygen-atom-transfer agents. The X-ray analysis of PFC crystals reveals that the compound crystallises in the orthorhombic space group CmcZ₁. The structure consists of discrete pyridinium cations and CrO₃ F anions with no significant hydrogen bonding. This results in total disorder of the pyridinium cation. The tetrahedral [CrO₃ F]⁻ ion lies on a crystallographic mirror plane.     

Thermal decomposition kinetics of potassium iodate

The thermal decomposition of potassium iodate (KIO₃) has been studied by both non-isothermal and isothermal thermogravimetry (TG). The non-isothermal simultaneous TG–differential thermal analysis (DTA) of the thermal decomposition of KIO₃ was carried out in nitrogen atmosphere at different heating rates. The isothermal decomposition of KIO₃ was studied using TG at different temperatures in the range 790–805 K in nitrogen atmosphere. The theoretical and experimental mass loss data are in good agreement for the thermal decomposition of KIO₃. The non-isothermal decomposition of KIO₃ was subjected to kinetic analyses by model-free approach, which is based on the isoconversional principle. The isothermal decomposition of KIO₃ was subjected to both conventional (model fitting) and model-free (isoconversional) methods. It has been observed that the activation energy values obtained from all these methods agree well. Isothermal model fitting analysis shows that the thermal decomposition kinetics of KIO₃ can be best described by the contracting cube equation.     

Effect of FeO x on the electrocatalytic properties of NiCo2O4 for O2 evolution from alkaline solutions

Mixtures of NiCo₂O₄ and FeO _x were obtained by thermal decomposition of the nitrates of Ni, Co, and Fe in appropriate proportions. Two series of electrodes were prepared: (1) at constant composition (20 mol% FeO _x ) and various calcination temperatures in the range 200 to 480 °C and (2) at constant calcination temperature (300 °C) and various compositions in the whole composition range 0 to 100 mol% FeO _x . The oxide layers were characterized by thermogravimetric analysis, X-ray diffraction, scanning electron microscopy, and cyclic voltammetry. Experimental data showed that the layers consist of a mixture of phases in which Fe oxide is present as Fe₂O₃. The electrocatalytic properties were assessed by means of quasi-stationary potentiostatic current-potential curves for the O₂ evolution reaction from alkaline solution. Results have shown that the mechanism of O₂ evolution depends on composition moderately. The electrocatalytic activity appears to depend on composition only slightly. Dedicated to Professor Oleg Petrii on the occasion of his 70th birthday on August 24th, 2007.