A weak cation-exchange monolith as stationary phase for the separation of peptide diastereomers by CEC

A CEC weak cation-exchange monolith has been prepared by in situ polymerization of acrylamide, methylenebisacrylamide and 4-acrylamidobutyric acid in a decanol-dimethylsulfoxide mixture as porogen. The columns were evaluated by SEM and characterized with regard to the separation of diastereomers and α/β-isomers of aspartyl peptides. Column preparation was reproducible as evidenced by comparison of the analyte retention times of several columns prepared simultaneously. Analyte separation was achieved using mobile phases consisting of acidic phosphate buffer and ACN. Under these conditions the peptides migrated due to their electrophoretic mobility but the EOF also contributed as driving force as a function of the pH of the mobile phase due to increasing dissociation of the carboxyl groups of the polymer. Raising the pH of the mobile phase also resulted in deprotonation of the peptides reducing analyte mobility. Due to these mechanisms each pair of diastereomeric peptides displayed the highest resolution at a different pH of the buffer component of the mobile phase. Comparing the weak-cation exchange monolith to an RP monolith and a strong cation-exchange monolith different elution order of some peptide diastereomers was observed, clearly illustrating that interactions with the stationary phase contribute to the CEC separations.     

Characterization and optimization by experimental design of a liquid chromatographic method for the separation of hydroxylated polychlorinated biphenyls on a polar-embedded stationary phase

Traditionally, the determination of hydroxylated polychlorinated biphenyls (OH-PCBs) has been carried out by gas chromatography (GC). However, the gas chromatographic behavior and sensitivity of this type of hydroxylated compounds are not always satisfactory, hence a prior derivatization of the OH-PCBs must be performed. Therefore, the development of liquid chromatographic methods should prove to be a very interesting task aimed at dealing with the instrumental determination of OH-PCBs. Taking into account that octadecylsilane stationary phases are not the most adequate for the separation of isobaric compounds, an amide-type column has been tested. For the development of the method, the Response Surface Methodology was used, based on a Box-Wilson Central Composite experimental design. The initial content of methanol in the mobile phase, the gradient time, and the concentration and the pH value of the buffer were chosen as relevant experimental parameters. A global optimum was obtained by selecting the elution time, the sensitivity and the overall resolution as responses to optimize. The developed method for liquid chromatography presented a very good resolution and sensitivity, and a reasonably short analysis time. In addition, a retention study was conducted in order to survey the different interactions that take place in the separation process, showing that hydrogen bonding is the main interaction between OH-PCBs and the amide-type stationary phase. However, a substantial contribution of dispersion forces was present in methanol contents in the mobile phase below 65%. Besides, the pH value of the mobile phase was found to be the most important parameter to control the hydrogen bond forces and therefore, to regulate the OH-PCBs separation.     

Near-infrared spectroscopy (NIRS) reflectance technology for the determination of tocopherols in alfalfa

The vitamin E (α- and (β+γ)-tocopherol) contents present in alfalfa (fresh or dehydrated) were analysed using near-infrared spectroscopy (NIRS) technology together with a remote reflectance fibre-optic probe. The range of vitamin E was 0.55–5.16 mg/100 g for α-tocopherol and 0.07–0.48 for (β+γ)-tocopherol. The regression method employed was modified partial least squares (MPLS). The equations developed using the fibre-optic probe for 69 samples of alfalfa (dehydrated and fresh) to determine the content of vitamin E in feeds had multiple correlation coefficients (RSQs) and prediction corrected standard errors (SEP (C)) of 0.946 and 0.321 mg/100 g for α-tocopherol and 0.956 and 0.022 mg/100 g for (β+γ)-tocopherol. The predicted values of vitamin E in feeds using NIRS technology applying the fibre-optic probe directly on the sample with neither previous treatment nor manipulation are comparable to those obtained using the chemical method, which included alkaline hydrolysis and hexane extraction of the vitamin from the unsaponifiable fraction before chromatographic determination.     

CEC separation of insect oostatic peptides using a strong-cation-exchange stationary phase

The separation of several insect oostatic peptides (IOPs) was achieved by using CEC with a strong-cation-exchange (SCX) stationary phase in the fused-silica capillary column of 75 microm id. The effect of organic modifier, ionic strength, buffer pH, applied voltage, and temperature on peptides' resolution was evaluated. Baseline separation of the studied IOPs was achieved using a mobile phase containing 100 mM pH 2.3 sodium phosphate buffer/water/ACN (10:20:70 v/v/v). In order to reduce the analysis time, experiments were performed in the short side mode where the stationary phase was packed for 7 cm only. The selection of the experimental parameters strongly influenced the retention time, resolution, and retention factor. An acidic pH was selected in order to positively charge the analyzed peptides, the pI's of which are about 3 in water buffer solutions. A good selectivity and resolution was achieved at pH <2.8; at higher pH the three parameters decreased due to reduced or even zero charge of peptides. The increase in the ionic strength of the buffer present in the mobile phase caused a decrease in retention factor for all the studied compounds due to the decreased interaction between analytes and stationary phase. Raising the ACN concentration in the mobile phase in the range 40-80% v/v caused an increase in both retention factor, retention time, and resolution due to the hydrophilic interactions of IOPs with free silanols and sulfonic groups of the stationary phase.     

Voltammetric behavior and determination of tocopherols with partial least squares calibration: analysis in vegetable oil samples

The voltammetric behavior of Vitamin E in the presence of olive oil is studied at the glassy carbon electrode, in a hexane-ethanol medium, with diverse techniques: sampled DC, differential pulse, and square-wave voltammetry. The influence of such variables as the hexane-ethanol proportion, sulfuric acid concentration, and instrumental parameters is studied. Separate voltammetric peaks are obtained for α-tocopherol and δ-tocopherol, but the peaks for β-tocopherol and γ-tocopherol overlap. For the simultaneous determination of α-, β+γ-, and δ-tocopherols in vegetable oils by the PLS-1 multivariate calibration method, the results using sampled DC and DPV voltammograms are compared. The DPV voltammograms are found to be the best data set. The proposed method is applied to the determination of the tocopherols in different vegetable oil samples. The olive oil samples needed a prior cleaning stage by solid-phase extraction on silica cartridges. The results are very acceptable.     

Regioselective separation of isomeric triacylglycerols by reversed-phase high-performance liquid chromatography: stationary phase and mobile phase effects

Complete regioselective separation of five pairs of isomeric dipalmitoyl polyalkenoyl glycerols with two to six double bonds in the unsaturated acyl residues has been achieved by RP-HPLC on a single ODS column. Four ODS columns with stationary phases containing different percentages of free silanol groups have been tested. Binary mobile phases of ACN admixed with dichloromethane, tetrahydrofuran, 1-propanol, 2-propanol, ethanol, or acetone have been examined. The choice of modifier depended on the nature of the stationary phase. The more polar solvents were better suited for stationary phases with higher percentage of free silanol groups. Isomeric species were eluted according to chain length, number of double bonds, and the position of the unsaturated acyl chain in the glycerol molecule. Retention increases in the order 20:5 < 22:6 < 18:3 < 20:4 < 18:2. Within each isomeric pair, the species with unsaturated acyl chain occupying either the sn-1- or the 3-position were retained preferentially. Complete simultaneous regioselective separation of 10 isomeric triacylglycerols in a single isocratic run on a single ODS column was demonstrated.     

冠醚固定相的制备及手性拆分

以R-联萘酚为原料合成了R-(1,1′-二萘基)-20-冠-6,并将其涂敷于C18硅胶(平均粒径5μm,孔径120nm)上制成了可用于高效液相色谱手性拆分的R-(1,1′-二萘基)-20-冠-6冠醚固定相(CSP).在以pH=2的高氯酸溶液为流动相,流速为0.1mL·min-1,柱温为25℃的条件下,研究了CSP对9种α-氨基酸对映体的拆分能力.实验结果表明,有5种手性氨基酸(缬氨酸、苯甘氨酸、对羟基苯甘氨酸、谷氨酸、色氨酸)得到不同程度的拆分,说明CSP能对手性氨基酸进行一定的拆分.     

Streptavidin chiral stationary phase for the separation of adenosine enantiomers

In this paper, a microbore column packed with streptavidin particles was used, at various temperatures (0-24 degrees C), to separate the adenosine enantiomers by HPLC. Using an aqueous mobile phase, the apparent enantioseparation was high for a small molecule, varying from 11.5 at 0 degrees C to 6.2 at 24 degrees C. From the experiments carried out with a streptavidin-biotin complex stationary phase, it was demonstrated that the blockage of the biotin sites of the immobilized streptavidin was responsible for a strong decrease in the enantioselectivity via a direct and/or an indirect effect. From the analysis of the concentration dependencies of the solute retention factor, it was also shown that a reduction of the D-adenosine specific binding sites occurred at the lowest temperature. The thermodynamic parameters determined from the van't Hoff plots indicated that the D-adenosine binding to the streptavidin specific sites was enthalpically driven.     

Characterization of UV-transparent capillaries for CEC and CE

This short communication describes features of UV-transparent capillaries employed for CEC and CE. A waveguide effect was observed when using UV-transparent capillaries. Through imaging with SEM, the UV-transparent coating was found to be highly porous unlike polyimide coating, which did not exhibit any porosity at all. Prolonged exposure to several commonly employed solvents with elevated pH caused abrasion of the coating at the capillary tip but no swelling of the UV-transparent coating was observed. Lastly, four different cutting techniques were compared to obtain smooth capillary tips.     

Ultra-High-Pressure Liquid Chromatographic method for the analysis of tocopherols in human colostrum and milk

A rapid, highly sensitive and direct Ultra-High-Pressure Liquid Chromatographic method was developed and validated for quantifying δ-, β + γ-, and α-tocopherol in human colostrum and milk. Two reversed-phase chromatographic columns and two detectors (Fluorescence Detector or FD and Photodiode Detector Array or PDA) were used and both methods were independently validated. Two internal standards were selected according to the detector used. Recoveries ranged from 96.71% to 103.55% and the relative standard deviations for the within-day precision were below 6% (PDA) and 3% (FD). Both approaches enabled to achieve low detection limits, on the order of ng (PDA) or pg (FD). Only 300 μL of sample and a chromatographic run of less than 1.6 min were enough to efficiently quantify the isomers in the colostrum and milk of Spanish women.     

High performance liquid chromatographic separation of dipeptide and tripeptide enantiomers using a chiral crown ether stationary phase

A chiral stationary phase (CSP) based on (-)-(18-crown-6)-2,3,11,12-tetracarboxylic acid was evaluated for the direct resolution of the enantiomers of dipeptides and tripeptides. The type and concentration of the acid and the methanol content were optimized with regard to retention time and resolution using Ala-Phe as model peptide. A mobile phase consisting of 10 mM sulfuric acid in 70% aqueous methanol was applied to the separation of a set of 16 structurally diverse dipeptides and tripeptides. Generally, the configuration of the amino acid at the N-terminus determined the enantiomer elution order. With a few exceptions the LL- and LD-enantiomers interacted stronger with the CSP compared to the corresponding DD- or DL-enantiomers. The experimental conditions also allowed the simultaneous separation of all four stereoisomers of Ala-Phe. Addition of ammonium sulfate generally reduced retention times and enantiomer resolution. Addition of triethylamine as modifier led to an overall increase of the retention times while the resolution did not show a general trend, increasing in the case of Ala-Ala but decreasing in the case of Ala-Phe.     

Capillary electrochromatographic separation of illicit drugs employing a cyano stationary phase

In this study, we present a capillary electrochromatographic method for separation of basic compounds of interest in forensic science (amphetamine, methamphetamine, 3,4-methylenedioxyamphetamine, 3,4-methylenedioxymethamphetamine, 3,4-methylenedioxyethylamphetamine, cocaine, codeine, heroin, morphine, and 6-monoacethylmorphine). Several analytical conditions were taken into account to completely separate in the same run the 10 drugs of abuse analyzed. Chromatographic retention, selectivity and efficiency were evaluated in dependence of the type of stationary phase (CN and RP-C₁₈ derivatized silica particles), mobile phase composition, buffer type and pH, sample injection. The optimum separation parameters were set up using a mixture of aqueous sodium phosphate buffer (pH 2.5)/acetonitrile (80/20, v/v) as the mobile phase, 10 kV and 20 °C as applied voltage and capillary temperature, respectively. Under these conditions all the studied analytes were baseline resolved within 20 min. The method performance was investigated in terms of precision, linearity, sensitivity and accuracy to demonstrate the applicability of the developed capillary electrochromatographic system to forensic analysis. Calibration curves provided a good linearity over a working range of 100–1200 ng/mL for all analytes. Limits of detection and quantification were in the range 5–12 ng/mL and 10–30 ng/mL, respectively. Then the method was applied to the analysis of a human urine sample spiked with a basic compounds’ mixture. Urine samples’ pre-treatment was carried out through a solid phase extraction (SPE) procedure on strong cation exchange (SCX) cartridges.     

Enantiomeric separation of a melatonin agonist Ramelteon using amylose-based chiral stationary phase

A new simple isocratic chiral liquid chromatographic method was developed for the enantiomeric purity of Ramelteon[(S)-N-[2-(1,6,7,8-tetrahydro-2H-indeno[5,4-b]furan-8-yl) ethyl]-propionamide], a melatonin agonist in bulk drugs. The chromatographic separation was achieved on Chiralpak AD-H, 250 mm × 4.6 mm, 5 μm column using a mobile phase system consisting of n-hexane, ethanol and methanesulfonic acid in the ratio of 900:100:0.1 (v/v/v). The mobile phase was pumped on the column at the flow rate of 1 mL min^?1. Addition of methane sulfonic acid in the mobile phase enhanced chromatographic efficiency and resolution between the enantiomers. The resolution between the enantiomers was found to be more than four. The developed method was subsequently validated and proved to be accurate and precise. The experimentally established limit of detection and quantification of (R)-enantiomer were found to be 25.5 and 77.2 ng ml^?1, respectively, for 20 μl injection volumes. The percentage recovery of (R)-enantiomer was ranged from 98.5 to 101.9 in bulk drug samples of Ramelteon. The stability of Ramelteon sample in analytical solution was checked for about 48 h at room temperature and was found to be stable for about 48 h. The proposed method was found to be suitable and accurate for the quantitative determination of (R)-enantiomer in drug substance.     

The effect of stationary phase on lipophilicity determination of beta-blockers using reverse-phase chromatographic systems

Evaluation of lipophilicity parameters for basic compounds using different chromatographic stationary phases is presented. An HPLC method for determination of lipophilic molecule-stationary phase interactions was based on gradient analysis. Differences in correlation between the lipophilicity of compounds and experimental chromatographic results obtained in pseudo-membrane systems showed a strong influence of stationary phase structure and physico-chemical properties. beta-Blocker drugs with varying lipophilicity and bio-activity were chosen as test compounds. The stationary phases used for the study were monolithic rod-structure C18 and silica gel octadecyl phase SG-C18 as reference material. The second group was silica gel-based polar-embedded alkylamide and cholesterolic phases. The mobile phase was composed of acetonitrile or methanol with ammonium acetate, and a linear gradient of methanol and acetonitrile in mobile phase was performed. A linear correlation of plots of log k(g) = f(log P) was observed, especially for polar-embedded phases, and this allowed log P(HPLC) to be calculated. The behavior of stationary phases in methanol and acetonitrile buffer showed differences between obtained log P(HPLC) values.     

Retention process in reversed phase TLC systems with polar bonded stationary phases

The retention of a solute in RP chromatography is a very complex process which depends on many factors. Therefore, the study of the influence of a mobile phase modifier concentration on the retention in different reversed phase chromatographic systems is very important for understanding the rules governing retention and mechanisms of substance separation in a chromatographic process. Composition changes and the nature of mobile phases enable tuning of the separated analytes' retention over a wide range of retention parameters and optimization of the chromatographic process as well. Optimization of the chromatographic process can be achieved by several different methods; one of them is the so-called interpretative strategy. The key approach adopted in this strategy is the implementation of adequate retention models that couple the retention of solute with the composition of a mixed mobile phase. The use of chemically bonded stationary phases composed of partially non-bonded silica matrix and organic ligands bonded to its surface in everyday chromatography practice leads to questions of the correct definition of the retention model and the dominant retention mechanism in such chromatographic systems. The retention model for an accurate prediction of retention factor as a function of modifier concentration and the heterogeneity of the adsorbent surface should be taken into consideration. In this work the influence of mobile-phase composition on the retention of sixteen model substances such as phenols, quinolines, and anilines used as test analytes in different RP-TLC systems with CN-, NH2-, and Diol-silica polar bonded stationary phases has been studied. The aim of this study is to compare the performance of three valuable retention models assumed as the partition, adsorption/partition, and adsorption mechanism of retention. All the models were verified for different RP-TLC systems by three statistical criteria. The results of investigations presented in this work demonstrate that the best agreement between the experimental and calculated Rf values was obtained by the use of new-generation retention models, which assume heterogeneity of adsorbent surface. The results reported here show that heterogeneity of the adsorbent surface may be important in analysis of the elution process in liquid chromatography. Consideration of the goodness of fit for the experimental data to the examined retention models is in conformity with the adsorption mechanism of retention on all polar bonded stationary phases in most eluent systems for most investigated compounds.     

Preparation and evaluation of a vancomycin-immobilized silica monolith as chiral stationary phase for CEC

Enantiomeric separations in CEC with the macrocyclic antibiotic vancomycin immobilized silica monolith as a chiral stationary phase are presented. The monolithic silica capillary columns were prepared by a sol-gel process in fused-silica capillaries with an inner diameter of 50 mum and subsequently in situ immobilization of vancomycin as a chiral selector by reductive amination. Enantioselectivity was obtained for eight pairs of enantiomers in nonaqueous polar organic or aqueous mobile phases and most of them were baseline-separated with high column efficiencies. It was observed that the organic modifier ratio (MeOH/ACN) in the polar organic mobile phase played a significant role in controlling the resolution and efficiency of the enantiomers. In enantiomeric separation of propranolol, repeatability for column efficiency and resolution in the nonaqueous mobile phase was given in terms of RSD values at 1.1 and 2.3% (n = 5) for run-to-run injections and 7.2 and 9.6% (n = 5) for column-to-column testing while repeatability for the separation of thalidomide in the aqueous mobile phase was given in terms of RSD values at 1.5, 2.8% and 6.1, 10.5%, respectively.     

Enantiomeric separation of amino alcohols by gas chromatography on a chiral stationary phase; influence of the perfluoroacylating reagent on the separation

Racemic amino alcohols have been separated as perfluoroacylated derivatives by gas chromatography using either improved Chirasil-Val or heptakis(2,6-di-O-methyl-3-O-pentyl)-β-cyclodextrin as stationary phase. Using Chirasil-Val all the amino alcohols investigated were separated to baseline (α values between 1.03 and 1.08) whereas only a few amino alcohols were resolved on the modified cyclodextrin column. The enantioselectivity obtained on the latter phase was, however, significantly higher. The separations were performed as trifluoroacetyl, pentafluoropropionyl, and heptafluorobutyryl derivatives and the chiral discrimination observed for the different derivatives was significantly different for both stationary phases. In oder to obtain a better understanding of the separation mechanism, the Gibbs-Helmholtz parameters Δ_(R,S)ΔH° and Δ_(R,S)ΔS° were determined. The most extraordinary result was obtained for the trifluoroacetyl derivative of allo-threoninol. In addition to the order of elution of the enantiomers being the opposite of that for the other compounds, the separation seems to be entropy controlled (the sign Δ_(R,S)ΔH° is positive), i.e. the separation improved at higher temperatures.