Determination of Sn(II) and Sn(IV) after mixed micelle-mediated cloud point extraction using alpha-polyoxometalate as a complexing agent by flame atomic absorption spectrometry

The cloud point extraction behavior of Sn(II) and Sn(IV) using alpha-polyoxometalate and mixed surfactants solution was investigated. The mixture of a nonionic surfactant (Triton X-100) and a cationic surfactant (CTAB) was utilized as a suitable micellar medium for preconcentration and extraction of tin complexes. Sn(II) in the presence of Sn(IV) was extracted with alpha-polyoxometalate, 0.3% (w/v) Triton X-100 and 3.5x10(-5) mol L(-1) CTAB at pH 1.2. Whereas the pH value of 3.7 were used for the individual determination of Sn(II) and Sn(IV) and also for total tin determination at the same conditions. Enrichment factors of 100 were obtained for the preconcentration of both metal ions. Under the optimal conditions, linearity was obeyed in the ranges of 55-670 microg L(-1) of Sn(II) and 46-750 microg L(-1) of Sn(IV) ion concentration. The detection limit of the method was also found to be 12.6 microg L(-1) for Sn(IV) and 8.4 microg L(-1) for Sn(II). The relative standard deviation of seven replicate determination of 100 microg L(-1) both metal ions were obtained about 2.4%. The diverse ion effect of some anions and cations on the extraction efficiency of target ions were tested. Finally, the optimized conditions developed were successfully utilized for the determination of each metal ion in various alloy, juice fruit, tape and waste water samples with satisfactory results.     

Effect of citric acid and hydrochloric acid on the polarographic behaviour of tin: Application to the determination of tin(II) in presence of tin(IV) in the activating solutions of the electroless plating of polymers

A new method for the determination of tin(II) in presence of tin(IV) is described. The method is based on differential pulse polarography on the hanging mercury drop electrode (HMDE). The effect of citric acid and hydrochloric acid concentrations on the polarographic peaks of tin(II) and tin(IV) has been studied. In 1 M HCl, the total quantity of tin can be determined, as under these conditions, in the absence of complexing agents, eventual variations in the oxidation states, in any concentration ratio, do not affect the peak height and the peak potential. In 0.2 M HCl and 0.2 M citric acid, tin(II) can be determined selectively in presence of tin(IV), as under these conditions, tin(IV) does not present polarographic response, while a well-defined peak is observed for tin(II). The method is applied to determine tin(II) and total tin in the activating solutions of the electroless plating of polymers.     

Application of experimental design in a method for screening sediments for global determination of organic tin by electrothermal atomic absorption spectrometry (ETAAS)

An experimental design was developed to obtain a simple procedure for global determination of organic tin compounds in sediment. Sediment was extracted by a two-phase method and tin was determined in the organic extract by electrothermal atomic absorption spectrometry (ETAAS), with palladium as chemical modifier. A Plackett-Burman design for screening and a fractional central composite design (CCD) for optimizing were used for evaluation of the effects of several variables. The results showed that sediment mass, volume and concentration of extracting acid, pyrolysis and atomization temperatures, and modifier concentration affect the determination. Reference material PACS-2 was analyzed to evaluate the procedure. It was possible to extract 82% of the organotin content certified in the reference sediment. The limit of detection (LOD) was 0.08 microg g(-1) and the relative standard deviation was 4%. The method was applied to the analysis of estuarine superficial sediments from Gipuzkoa (Spain). The organotin content of these samples ranged from 0.7 to 7.7 microg g(-1), as tin, on a dry-weight basis.     

Determination of trace amounts of lead in mussels by flow-injection flame atomic-absorption spectrometry coupled with on-line minicolumn preconcentration

A minicolumn packed with poly(aminophosphonic acid) chelating resin incorporated in an on-line preconcentration system for flame atomic-absorption spectrometry was used to determine ultratrace amounts of lead in mussel samples at microg L(-1) level. The preconcentrated lead was eluted with hydrochloric acid and injected directly into the nebulizer for atomization in an air-acetylene flame for measurement. The performance characteristics of the determination of lead were: preconcentration factor 26.8 for 1 min preconcentration time, detection limit (3sigma) in the sample digest was 0.25 microg g(-1) (dry weight) for a sample volume of 3.5 mL and 0.2 g sample (preconcentration time 1 min), precision (RSD) 2.3% for 25 microg L(-1) and 2.0% for 50 microg L(-1). The sampling frequency was 45 h(-1). The method was highly tolerant of interferences, and the results obtained for the determination of lead in a reference material testify to the applicability of the proposed procedure to the determination of lead at ultratrace level in biological materials such as mussel samples.     

Determination of platinum and iridium in reforming catalysts by second derivative and absorptiometric spectrophotometry

Summary Investigations on the spectrophotometric determination of platinum as a complex formed by tin(II)chloride in hydrochloric acid are reported. The determination of platinum was found to be interfered with by iridium, because it also forms a complex with tin(II) chloride. The features of the derivative absorption spectrophotometry for the quantitative determination of platinum and iridium was also studied. The analytical application of the method for the determination of platinum and iridium in catalysts was investigated.     

Inorganic tin(II) determination by FIA with amperometric detection of its oxinate complex

A highly selective, rapid and direct amperometric method, based on the formation of a complex between tin(II) and 8-hydroxyquinoline (oxine), has been developed for the determination of trace levels of tin(II) using flow injection analysis. Tin(II) electro-oxidation was catalyzed by oxine; its oxidation peak occurred at +0.05 V vs. Ag/AgCl at a glassy carbon electrode in 0.1 mol 1⁻¹ acetate buffer (pH 6). A linear relationship was obtained between the peak current and the tin(II) concentration in the range 0.25-20 μmol 1⁻¹. The detection limit was 0.1 μmol 1⁻¹ and the relative standard deviation calculated by the injection of a 10 μmol 1⁻¹ tin(II) solution was 5% (n = 20). Optimization of several experimental parameters has been carried out and the influence of numerous cations and possible interfering molecules encountered in radiopharmaceuticals and in dental gels has been investigated. The method was applied to the determination of tin(II) in dental gels.     

Quinalizarin anchored on Amberlite XAD-2. A new matrix for solid-phase extraction of metal ions for flame atomic absorption spectrometric determination

Amberlite XAD-2 has been functionalized by coupling it to quinalizarin [1,2,5,8-tetrahydroxyanthraquinone] by means of an -N = N- spacer. Elemental analysis, thermogravimetric analysis, and infrared spectra were used to characterize the resulting new polymer matrix. The matrix has been used to preconcentrate Cu(II), Cd(II), Co(II), Pb(II), Zn(II), and Mn(II) before their determination by flame atomic absorption spectrometry (FAAS). UO2(II) has been preconcentrated for fluorimetric determination. The optimum pH values for maximum adsorption of the metals are between 5.0 and 7.0. All these metal ions are desorbed (recovery 91-99%) with 4 mol L(-1) HNO3. The adsorptive capacity of the resin was found to be in the range 0.94-5.28 mg metal g(-1) resin and loading half-life (t1/2) between 5.3 and 15.0 min. The effects of NaF, NaCl, NaNO3, Na2SO4, Na3PO4, Ca(II), and Mg(II) on the adsorption of these metal ions (0.2 microg mL(-1)) are reported. The lower limits of detection for these metal ions are between 1 and 15.0 microg L(-1). After enrichment on this matrix flame AAS has been used to determine these metal ions (except the uranyl ion) in river water samples (RSD < or = 6.5%); fluorimetry was used to determine uranyl ion in well water samples (RSD < or = 6.3%). Cobalt from pharmaceutical vitamin tablets was preconcentrated by use of this chelating resin and estimated by FAAS (RSD approximately 4%).     

Flow injection atomic absorption spectrometric determination of iodide using an on-line preconcentration technique

A continuous flow atomic absorption spectrometric system was used to develop an efficient on-line preconcentration-elution procedure for the determination of iodide traces. Chromium (VI) is introduced into the flow system and is reduced to chromium (III) in acid medium proportionally to the iodide present in the sample. The Cr(III) reduced by iodide is retained on a minicolumn packed with a poly(aminophosphonic acid) chelating resin, while unreduced Cr(VI) is not retained. Reduced Cr(III) is preconcentrated by passing the sample containing iodide through the system during 3 min, and is then eluted with 0.5 mol L(-1) hydrochloric acid and determined by flame atomic absorption spectrometry (FAAS). The detection limit (3sigma) obtained is 2.5 microg L(-1). Other ions typically present in waters do not interfere. The proposed method allows the determination of iodide in the range 6-220 microg L(-1) with a relative standard deviation of 2.7% at a rate of 17 samples h(-1). The method has been applied to the determination of iodide in tap and sea waters.     

Preconcentration of Nickel(II) in White Wine Using Quinoxaline-2,3-dithiol and a Finely Divided Anion-Exchange Resin for the Determination by Solid-Phase Spectrophotometry

A simple and sensitive method for the determination of trace amounts of nickel(II) is described. The method is based on the adsorptive enrichment of nickel(II) as the complex with quinoxaline-2,3-dithiol using a finely divided anion-exchange resin, collection of the resin on a membrane filter by filtration, and direct measurement of the absorbance of the resultant circular thin layer by reflective spectrophotometry at 605 nm. In the presence of interfering cations such as copper(II) and cobalt(II) a sample solution is first filtered, after the addition of ammonium thiocyanate and Zephiramine, to extract these cations onto a membrane filter as the ion-pair precipitate formed between the metal-thiocyanate complex anions and Zephiramine cations, then nickel(II) in the filtrate is determined. Interferences from iron(III), silver(I), bismuth(III), cadmium(II), mercury(II), indium(III), palladium(II), platinum(IV), tin(IV), and zinc(II) can also be eliminated. The proposed method was applied to the determination of nickel in white wine. The concentrations of nickel found in 5-ml aliquots of 10 different wine samples were in the range 16.1-68.0 ng ml⁻¹.     

Flow injection spectrophotometric determination of ascorbic acid in soft drinks and beer

Two spectrophotometric methods, a photochemical and a non-photochemical, for the determination of ascorbic acid in soft drinks and beer using a flow-injection system are proposed. The non-photochemical method is based on the redox reaction that takes place between ascorbic acid and Fe(III), yielding dehydroascorbic acid and Fe(II). Fe(II) reacts with 1,10-phenantroline, originating the reddish orange Fe(phen)3(2+) complex (ferroin). This complex is spectrophotometrically monitored at 512 nm, and the signal is directly related to the concentration of ascorbic acid in the sample. The photochemical method has the same basis, nevertheless, uses the irradiation with visible light to enhance the redox reaction and so achieve higher sensitivities in the analysis. The non-photochemical method shows a linear range between 5 and 80 microg mL(-1), with a relative standard deviation of 1.6% (n = 11), a detection limit of 2.7 microg mL(-1) and a sample throughput of 60 samples h(-1). The photochemical method shows a linear range between 1 and 80 microg mL(-1), with a relative standard deviation of 1.0% (n = 11 ), a detection limit of 0.5 microg mL(-1) and a sample throughput of 40 samples h(-1).     

Flow-Injection Study and Analytical Applications of the Reactions of Palladium(II) and Platinum(IV) with Tin(II) Chloride in Hydrochloric Acid Solutions

The interaction of palladium(II) and platinum(II) with tin(II) chloride in hydrochloric acid solutions was studied by flow-injection (FI) spectrophotometry. It was found using kinetic measurements in the stopped flow mode that the composition of detected products and the rate of their formation depend on the concentrations of tin(II) and chloride ions in the reaction zone and on the acidity of the solution. Optimal FI conditions were found, and the selectivity of interaction of palladium(II) with tin(II) chloride was estimated for the detection of the signal at 407 nm (yellow form) and 646 nm (green form). It was demonstrated that the reaction of the formation of yellow platinum(IV) complexes is slower than that for palladium(II), especially at rather low concentrations of hydrochloric acid in the reaction flow. Based on the detection of green complexes of palladium(II) with tin(II) chloride, a flow injection method was proposed for the selective spectrophotometric determination of palladium(II) in the presence of other platinum-group metals. The height of the recorded peak is directly proportional to the concentration of palladium(II) in the injected solution in the range of 0.028–0.300 mM. The method was used for the analysis of pharmaceuticals and industrial catalysts.     

Indirect spectrophotometric determination of micro-amounts of Tin(II) in the presence of Tin(IV) and in dental gels.

A method for determining microgram amounts of tin(II) in synthetic samples containing tin(IV) and in dental gels has been developed. The procedure involves the oxidation of tin(II) with iron(III) in hydrochloric acid and spectrophotometric determination of the resulting iron(II) as a FerroZine complex.     

Rapid determination of gold in geological samples using flow injection solid-phase chemiluminescence.

The solid-phase chemiluminescence analysis of gold on the surface of an anion-exchange resin was studied. A method for the fast determination of gold using flow injection was established. The anion-exchange resin was used as an adsorbent of gold ion in the form of AuCl4-. The cation-exchange resin was used for the on-line separation of cations in the matrix. To obtain the best results, the preconcentration and separation conditions, chemiluminescence conditions, interfering ions and their elimination conditions were optimized. The linear range of the calibration curve of AuCl4- is from 0 microg ml(-1) to 5.00 microg ml(-1). The detection limit of AuCl4- is 0.012 microg ml(-1). The method has been used for the determination of gold in geological samples (standard ores). The results are in agreement with certified value of gold standard samples with relative standard deviation from 2.22% to 8.97%. Through the use of flow injection, the preconcentration and separation can be performed automatically.     

4-(N,N-diethylamino) benzaldehyde thiosemicarbazone in the spectrophotometric determination of palladium

4-(N,N-diethylamino)benzaldehyde thiosemicarbazone(DEABT) is proposed as a sensitive and selective analytical reagent for the spectrophotometric determination of palladium(II). The reagent reacts with palladium (II) in a potassium hydrogen phthalate-hydrochloric acid buffer of pH 3.0, to form a yellow complex. Beer's law is obeyed in the concentration range up to 3.60 microgmL(-1). The optimum concentration range for minimum photometric error as determined by Ringbom plot method is 0.36 - 3.24 microg mL(-1). The yellow Pd(II)-DEABT complex shows a maximum absorbance at 408 nm, with molar absorptivity of 3.33 x 10(4) dm3 mol(-1) cm(-1) and Sandell's sensitivity of the complex from Beer's data, for D = 0.001, is 0.0032 microg cm(-2). The composition of the Pd(II)-DEABT complex is found to be 1:2 (M:L). The interference of various cations and anions in the method were studied. The proposed method was successfully used for the determination of Pd(II) in alloys, catalysts, complexes and model mixtures with a fair degree of accuracy.     

Simultaneous determination of tin and lead by a.c. anodic stripping voltammetry at a hanging mercury drop electrode sensitized by cetyltrimethylammoniu

The influence of cetyltrimethylammonium bromide (CTAB) on the simultaneous determination of tin(IV) and lead(II) by anodic stripping voltammetry at a hanging mercury drop electrode (HMDE) in a 0.1 M hydrochloric acid—0.1 M oxalic acid medium was studied using d.c. and a.c. stripping. In the presence of CTAB, tin and lead show voltammetric peaks separated by 100 mV, the sensitivity depending on the concentration of CTAB. The best conditions for the simultaneous determination of both elements (2 × 10^-3 M) were found. A method is proposed for the determination of tin in the presence of lead and three procedures are given for the determination of lead in the presence of tin.     

The determination of trace amounts of tin by flow-injection hydride generation atomic-absorption spectrometry with on-line ion-exchange separation and preconcentration

A hydride generation atomic-absorption spectrometric (AAS) method with flow-injection (FI), aimed at developing a practical routine assay for the determination of tin in food digests, is described. In order to modify the sample matrix and to achieve optimized and reproducible conditions for the hydride generation reaction, the analyte is initially converted into its chlorostannate-complex thereby allowing it to be separated and preconcentrated on-line on an incorporated micro-column packed with a strongly basic anion exchanger and subsequently to be eluted by diluted nitric acid under strictly controlled conditions. Optimum acidic conditions for the FI hydride generation AAS system was found to be 0.01-0.05M nitric acid. At a consumption of 2.7-ml sample volume, aspirated by time-based injection, the procedure resulted in an enrichment factor of 3.5 and yielded a detection limit of 0.08 microg/l. (3sigma) at a sampling frequency of 72/hr. The precision was 2.5% rsd at the 10 microg/l. level. Potential interferents, such as Ni(II), Co(II), Zn(II) and Fe(III) could, at a Sn level of 10 microg/l., be tolerated at an excess of 1000 times without impairing the assay, while a 100-1000-fold excess of Cu(II) decreased the signal by 10-15%. Recoveries in the range 94-102% were obtained for canned food sample digests spiked with 10 microg/l. Sn.     

Spectrophotometric determination of cobalt with 1-(2-pyridylazo)-2-naphthol and surfactants

A simple and highly selective spectrophotometric method for the determination of cobalt based upon the rapid reaction with PAN in the presence of surfactants and minute amounts of ammonium persulphate at pH 5.0 is described. The cobalt(III) chelate is made water-soluble by a neutral surfactant. Triton X-100, combined with sodium dodecylbenzene sulphonate (DBS). Iron(III), bismuth, tin(IV) and aluminium are masked with oxalate or citrate. Iron(II) must be absent. The other metal-PAN chelates, except that of nickel, are readily decomposed by EDTA. Up to 150 microg of nickel does not interfere. When larger amounts up to 625 microg are present, the absorbance can be corrected by measurements at two wavelengths. In a strongly acid medium (below pH 0.5) the nickel and other metal chelates are completely and instantaneously decomposed, while the cobalt(III) chelate remains unchanged. When, in place of EDTA, several ml of 6M hydrochloric acid are added after the colour development, nickel in quantities up to 1250 microg can be tolerated. A several hundredfold excess of zinc and manganese does not interfere. At 620 nm Beer's law is obeyed over the cobalt concentration range 0.4-3.2 microg/ml. The precision (95% confidence) is +/- 1.0 microg for 100 microg of cobalt. The molar absorptivity is 1.90 x 10(4) l. mole(-1) .cm(-1).     

Minicolumn field sampling--preconcentration of trace zinc from seawater and its laboratory detection by flow injection flame atomic absorption spectrometry.

A simple field sampling-preconcentration method for zinc determination in seawater is described. Seawater was collected in situ by pumping it through a minicolumn packed with a chelating resin (Chelite P) connected to a field flow preconcentration system (FFPS). These packed minicolumns retain the dissolved zinc, and once are loaded with the analyte, they are returned to the laboratory where they are sequentially inserted into a flow injection system for on-line zinc elution with diluted hydrochloric acid and flame atomic absorption spectrometric detection. A factorial design has been used to optimize the FFPS and the flow injection elution process. The proposed method has a linear calibration range from 0.07 to at least 9.4 microg L(-1) of zinc, with a detection limit of 0.02 microg L(-1) and a throughput of 26 samples h(-1). Validation was carried out against certified reference water samples. This procedure has been successfully applied to the determination of Zn in seawater samples from Galicia (Spain).     

Spectrophotometric flow injection methods for zinc determination in pharmaceutical and biological samples.

Zinc ions form a yellow complex with di-2-pyridyl ketone salicyloylhydrazone (DPKSH). This complex showed maximum absorption at 376 nm, and it was used to develop spectrophotometric flow injection methods for Zn(II) determination in different samples. Two types of flow systems were proposed. In the first system, a linear analytical curve was obtained in a concentration range from 0.217 to 4.60 mg L(-1) Zn(II), with a detection limit of 48.8 microg L(-1). In the second system, a minicolumn packed with an anion exchanger resin was used to concentrate Zn(II) as a chlorocomplex, and a linear analytical curve within a concentration range from 0.0824 to 2.06 mg L(-1) Zn(II) was obtained, having a detection limit of 13.9 microg L(-1). The developed methods were applied to biological and pharmaceutical samples, and a great compliance was observed by comparing the results with ones obtained by an atomic absorption technique.     

H-point standard addition method for simultaneous spectrophotometric determination of Co(II) and Ni(II) by 1-(2-pyridylazo)2-naphthol in micellar media

A very simple and selective spectrophotometric method for simultaneous determination of Co(II) and Ni(II) by 1-(2-pyridylazo) 2-naphthol (PAN), in micellar media, using H-point standard addition method (HPSAM) is described. The ligand and its metal complexes (Co(II)-PAN and Ni(II)-PAN) were made water-soluble by the neutral surfactant Triton X-100, and therefore, no extraction with organic solvents was required. Formation of both the complexes was complete within 10 min at pH 9 (adjusted by ammonia buffer). The linear range was 0.10-2.00 microg ml(-1) for Co(II) and 0.05-1.50 microg ml(-1) for Ni(II). The relative standard deviation (R.S.D.) for the simultaneous determination of 0.50 microg ml(-1) each of Co(II) and Ni(II) was 2.32 and 3.13%, respectively. Interference effects of common anions and cations were studied and the method was applied to simultaneous determination of Co(II) and Ni(II) in alloy samples. The method was compared with derivative spectrophotometric method.