2‐Aminocyclopentene‐1‐Dithiocarboxylic Acid‐Naphthalene Adsorbent for the Preconcentration and Determination of a Trace Copper in Real Samples by Spectrophotometric Method

A solid uncharged complex produced from 2‐aminocyclopentene‐1‐dithiocarboxylic acid (synthetic reagent) on naphthalene provides a very sensitive, selective and economical method for the preconcentration and determination of trace amounts of copper in drug and alloy samples. The 2‐aminocyclopentene‐1‐dithiocarboxylate of copper is retained quantitatively on microcrystalline naphthalene in the pH range 2.8–3.3. After filtration the solid mass consisting of copper complex‐naphthalene is dissolved with 4 mL of dimethylformamide (DMF). The absorbance is measured at 462 nm with a spectrophotometer against the reagent blank and molar absorptivity found to be 2.8 × 10⁵ liter mol^?1 cm^?1. Beer's law is obeyed over the concentration range of 0.1–16.0 μg of copper in 4 mL of the dimethylformamide solution. Detection limit is 3 ng mL^?1 [signal to noise ratio = 2]. Ten replicate determinations on a sample containing 1 μg of copper gave a relative standard deviation of 0.76%. The interference of a large number of anions and cations have been studied and the optimized conditions developed were utilized for determination of copper in various real samples.     

Atomic absorption spectrometric determination of trace amounts of nickel after preconcentration with [1-(2-Pyridylazo)-2-Naphthol]-Naphthalene adsorbent or after adsorption of its complex on microcrystalline naphthalene

An atomic absorption spectrometric method for the determination of trace amounts of nickel after adsorption of its 1 -(2-pyridylazo)-2-naphthol complex on microcrystalline naphthalene has been developed. This complex is adsorbed on microcrystalline naphthalene in the pH range 4.5-7.8 from large volumes of aque ous solutions of various alloys and biological and environmental samples containing nickel. After filtration, the solid mass consisting of nickel complex and naphthalene was dissolved in 5 mL of dimethylformamide, and the metal was determined using a flame atomic absorption spectrometer at a wavelength of 232 nm. Alternatively, nickel can be quantitatively adsorbed on [l-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. The calibration curve is linear over the concentration range 2.0-100 Μg of nickel in 5 mL of the final dimethylformamide solution. Eight replicate determinations of 20 Μg of nickel give a mean absorbance of 0.072 with a relative standard deviation of 1.3%. The sensitivity for 1% absorption is 0.24 Μg/mL. Various parameters such as the effect of pH, the volume of the aqueous phase, and the interference of a large number of metal ions with the determination of nickel have been studied in detail to optimize the conditions for its determination in various standard alloys and biological and environmental samples. This article was submitted by the authors in English.     

Atomic absorption spectrometric determination of trace zinc in alloys and biological samples after preconcentration with [1-(2-pyridylazo)-2-naphthol] on microcrystalline naphthalene

An atomic absorption spectrometric method for the determination of trace amounts of zinc after adsorption of its [1-(2-pyridylazo)-2-naphthol] complex on microcrystalline naphthalene has been developed. This complex is adsorbed on microcrystalline naphthalene in the pH range 3.5-7.5 from large volumes of aqueous solutions of various alloys and biological samples with a preconcentration factor of 40. After filtration, the solid mass consisting of the zinc complex and naphthalene was dissolved with 5 ml of dimethylformamide and the metal was determined by flame atomic absorption spectrometry. Zinc can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. About 0.5 ng of zinc can be concentrated in a column from 200 ml of aqueous sample, where its concentration is as low as 2.5 pg ml-1. The calibration curve is linear in the range 0.1-6.5 ng ml-1 in dimethylformamide solution. Eight replicate determinations of 2 ng ml-1 of zinc gave a mean absorbance of 0.145 with a relative standard deviation of 1.5%. The sensitivity for 1% absorption was 0.061 ng ml-1. Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of zinc, have been studied in detail to optimize the conditions for the determination of zinc in various standard complex materials.     

Atomic absorption spectrometric determination of ultra trace amounts of zinc after preconcentration with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and ammonium tetraphenylborate on microcrystalline naphthalene or by column method

Zinc is quantitatively retained on 2-(5-bromo-2-pyridylazo)-5-diethylamminophenol (5-BrPADAP)-ammonium tetraphenylborate with microcrystalline naphthalene or by a column method in the pH range 7.5-9.0 from a large volume of aqueous solutions of various samples. After filtration, the solid mass consisting of the zinc complex and naphthalene was dissolved with 5 ml of dimethylflarmamide and the metal was determined by atomic absorption spectrometry. Zinc complex can alternatively be quantitatively adsorbed on ammonium tetrphenylborate-naphthalene adsorbent packed in a column and determined similarly. The calibration curve is linear 0.05-4.0 ppb in dimethylformamide solution. Eight replicate detenninations of 1.0 ppb of zinc gave a mean absorbance of 0.124 with a relative standard deviation of 1.3%. The sensitivity for 1% absorption was 0.035 ppb. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of zinc in various standard samples.     

Flame atomic absorption spectrometric determination of trace amounts of manganese in alloys and biological samples after preconcentration with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and ammonium tetraphenylborate on microcrystalline naphthalene or by column method.

Manganese is quantitatively retained on 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-ammonium tetraphenylborate with microcrystalline naphthalene or by a column method in the pH range 7.5-10.5 from large volumes of aqueous solutions of various samples. After filtration, each solid mass consisting of the manganese complex and naphthalene was dissolved with 5 ml of dimethylformamide and the metal was determined by flame atomic absorption spectrometry. Manganese complex can alternatively be quantitatively adsorbed on ammonium tetraphenylborate-naphthalene adsorbent packed in a column and determined similarly. About 0.1 microgram of manganese can be concentrated in a column from 500 ml of aqueous sample, where its concentration is as low as 0.2 ppb. Eight replicate determinations of 1.0 ppm of manganese gave a mean absorbance of 0.224 with a relative standard deviation of 1.8%. The sensitivity for 1% absorption was 19 ppb. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of manganese in various standard samples.     

Synthesis of 2-(2′,3′-dihydroxypropyl)-5-amino-2H-1,2,4-thiadiazol-3-one and 3-(2′,3′-dihydroxypropyl)-5-amino-3H-1,3,4-thiadiazol-2-one

The synthesis of two new acyclic nucleoside analogs, 2-(2′,3′-dihydroxypropyl)-5-amino-2H-1,2,4-thiadiazol-3-one (1) and 3-(2′,3′-dihydroxypropyl)-5-amino-3H-1,3,4-thiadiazol-2-one (2), is reported. The first compound, 1, was obtained by reaction of 3-chloro-1,2-propanediol with the sodium salt of 5-amino-2H-1,2,4-thiadiazol-3-one (3) in anhydrous dimethylformamide. Similarly, 5-amino-3H-1,3,4-thiadiazol-2-one (4) reacted with 3-chloro-1,2-propanediol to give 2. The thiadiazole 4 was prepared by condensation-cyclization of hydrazothiodicarbonamide (9).     

Nucleosides and Nucleotides. Part 13. Synthesis and spectral properties of 1- (3′-O-Phosphoryl-2′-deoxy-β -D-ribofuranosyl)-2(1H)-pyridone-(3′-5′)-1-(2′-deoxy-β-D-ribofuranosyl)-2 (1H)-pyridone

The dinucleoside phosphate Π_dpΠ_d ( 4 ) was synthesized from the monomers 1-(5′-O-monomethoxytrityl - 2′ - deoxy - β - D - ribofuranosyl) - 2 (1 H) - pyridone ((MeOTr) Π_d, 2 ) and 1-(5′-O-phosphoryl-3′-O-acetyl-2′-deoxy-β-D -ribofuranosyl)-(1H)-pyridone (pΠ_d(Ac), 3 ). Its 6.4% hyperchromicity and an analysis of the ¹H-NMR. spectra indicate that the conformation and the base-base interactions in 4 are similar to those in natural pyrimidine dinucleoside phosphates.     

Spectrophotometric determination of copper after adsorption of its 1-phenyl-4,4,6-trimethyl(1H, 4H)-pyrimidine-2-thiol complex onto microcrystalline naphthalene

A selective Spectrophotometric method has been developed for the trace determination of copper after adsorption of its 1-phenyl-4,4,6-trimethyl(1H, 4H)-pyrimidine-2-thiol (PTPT) complex onto microcrystalline naphthalene. The complex is quantitatively adsorbed on naphthalene in the pH range 7.5–11.5, separated by filtration, dissolved in dimethylformamide (DMF) and determined spectrophotometrically at 400 nm. Beer's law is obeyed in the concentration range 2.5–37.5 g of copper in 10 ml of DMF. The molar absorptivity and Sandell's sensitivity are 1.30 × 10⁴1 · mol^–1 · cm^–1 and 0.0048g cm^–2, respectively. Ten replicate analyses of a solution containing 20.0 g of copper gave a mean absorbance of 0.410 with a relative standard deviation of 0.91 %. The interferences of various ions have been studied and the method has been validated by the determination of copper in various standard reference materials, beers, wines, human hair, goat liver and environmental samples.On leave from St. Stephen's College, Delhi 110 007, India     

Determination of manganese by flame atomic absorption spectrometry after its adsorption onto naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN)

A system for determination of manganese, after preconcentration with 3% (w/w) 1-(2-pyridylazo)-2-naphthol (PAN), adsorbed on microcrystalline naphthalene is proposed. An amount of 200 mg of this complexing mixture is placed in a glass column and conditioned with a NH₄Cl/NH₄OH buffer solution (pH 9.5). The aqueous sample, containing manganese, is treated with an ammonium tartrate solution, then with a hydroxylammonium chloride solution and, finally, with a buffer solution. The resulting solution is passed through the column containing microcrystalline naphthalene modified with 1-(2-pyridylazo)-2-naphthol (PAN) where Mn(II) is retained. The column is first washed with deionized water and then with 10.0 ml of dimethylformamide to dissolve the Mn(II)-PAN/naphthalene complex. Manganese is determined by air-acetylene flame atomic absorption spectrometry. About 1 μg of manganese can be concentrated from 200 ml of aqueous sample, allowing a preconcentration factor of 20, a limit of quantification of 5 ng ml⁻¹ and R.S.D. of 3.8%. The accuracy was ascertained using certified reference materials, including samples of urine and glass. Water samples were also analysed and the results are in good agreement with those obtained by graphite furnace atomic absorption spectrometry.     

Chromatographic preconcentration of copper in environmental and biological samples using 2,4,6-tri(2-pyridyl)-1,3,5-triazine-tetraphenylborate-naphthalene adsorbent

A method was established for the determination of trace amounts of copper using chromatographic preconcentration of copper(I) with 2,4,6-tri(2-pyridyl)-1,3,5-triazine and tetraphenylborate. Copper is quantitatively adsorbed on this adsorbent in the pH range 1.8–10.5 and at flow-rates of 0.2–10 ml/min. The solid mass consisting of copper complex along with naphthalene is dissolved from the column with 5 ml of dimethylformamide. A calibration curve is obeyed over the concentration range 0.2–10.0 g of copper in 5 ml of dimethylformamide. Eight replicate determinations of 3 g of copper gave a mean absorbance of 0.185 with a relative standard deviation of 1.4%. The characteristic concentration for 1% absorption is 0.0143 g/ml (0.103 gmg/ml for direct AAS in aqueous medium). The interference of various ion and salts has been studied and the proposed method has been employed to the determination of copper in biological and water samples.     

Flame atomic absorption spectrometric determination of trace chromium in various standard samples after preconcentration with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

Chromium can be quantitatively retained as 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-tetraphenylborate(TPB) complex onto microcrystalline naphthalene in the pH range 4.8–5.9 from a large volume of aqueous solutions of various standard samples. After filtration, the solid mass consisting of the chromium complex and naphthalene was dissolved with 5 mL of dimethylformamide and the metal was determined by air-acetylene FAAS. A detection limit of ¶4 ng/mL for chromium was established. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of chromium in various standard alloys and biological samples.     

Derivative spectrophotometric determination of iridium after preconcentration of its 1-(2-pyridylazo)-2-naphthol complex on microcrystalline naphthalene

Iridium is preconcentrated from the large volume of its aqueous solution using 1-(2-pyridylazo-2-naphthol) (PAN) on microcrystalline naphthalene in the pH range of 4.5-6.0. The solid mass after filtration is dissolved with 5 ml of dimethylformamide (DMF) and the metal determined by first derivative spectrophotometry. The detection limit is 20 ppb (signal to noise ratio = 2) and the calibration curve is linear over the concentration range 0.25-75.0 mug in 5 ml of the final DMF solution with a correlation coefficient of 0.9996 and relative standard deviation of +/- 1.1%. Various parameters such as the effect of pH, volume of aqueous phase, choice of solvent, reagent and naphthalene concentration, shaking time and interference of a number of metal ions on the determination of trace amount of iridium have been studied in detail to optimize the conditions for its determination in synthetic samples corresponding to various standard alloys and environmental samples.     

(6′RS,8′RS,2E)- und (6′RS,8′SR,2E)-3-Methyl-3-(2y,2′,6′-trimethyl-7′-oxabicyclo[4.3.0]non-9′-en-8′-yl)-2-propenal ([(5RS,8RS)- und (5RS,8SR)-5,8-Epoxy-5,8-dihydro-ionyloinden]acetaldehyd): Synthese und Röntgenstrukturanalyse

Synthesis and X-Ray Structure of (6′RS,8′RS,2E)- and (6′RS,8′SR,2E)-3-Methyl-3-(2′,2′,6′-trimethyl-7′-oxabicyclo[4.3.0]non-9′-en-8′-yl)-2-propenal ([(5RS,8RS)- and (5RS,8SR)-5,8-Epoxy-5,8-dihydro-ionylidene]acetaldehyde) To check our previous spectroscopic assignments of the structures of trans- and cis-substituted furanoid end groups of carotenoid-5,8-epoxides, we now have synthesized the title compounds. An X-ray structure determination of a single crystal of the trans-isomer (±)- -10A is in agreement with the ¹ H-NMR spectroscopic arguments: isomers with Δδ (H? C(7), H? C(8)) = 0.15–0.22 ppm and J > 1.4 for H? C(7) belong to the cis-series; Δδ in trans-compounds is < 0.07 ppm, and H? C(7) appears as a broad singulett.     

Nucleoside und Nucleotide. Teil 10. Synthese von Thymidylyl-(3′-5′) -thymidylyl-(3′-5′)-1-(2′-desoxy-β-D-ribofuranosyl)-2(1 H)-pyridon

Nucleosides and Nucleotides. Part 10. Synthesis of Thymidylyl-(3′-5′)-thymidylyl-(3′-5′)-1-(2′-deoxy-β-D - ribofuranosyl)-2(1 H)-pyridone The synthesis of 5′-O-monomethoxytritylthymidylyl-(3′-5′)-thymidylyl-(3′-5′)-1-(2′-deoxy-β-D -ribofuranosyl)-2(1H)-pyridone ((MeOTr)T_dpT_dp∏_d, 5 ) and of thymidylyl-(3′-5′)-thymidylyl-(3′-5′)-1-(2′-deoxy-β-D -ribofuranosyl)-2(1 H)-pyridone (T_dpT_dp∏_d, 11 ) by condensing (MeOTr) T_dpT_d ( 3 ) and p∏_d(Ac) ( 4 ) in the presence of DCC in abs. pyridine is described. Condensation of (MeOTr) T_dpT_dp ( 6 ) with Π_d(Ac) ( 7 ) did not yield the desired product 5 because compound 6 formed the 3′-pyrophosphate. The removal of the acetyl- and p-methoxytrityl protecting group was effected by treatment with conc. ammonia solution at room temperature, and acetic acid/pyridine 7 : 3 at 100°, respectively. Enzymatic degradation of the trinucleoside diphosphate 11 with phosphodiesterase I and II yielded T_d, pT_d and p∏_d, T_dp and Π_d, respectively, in correct ratios.     

Spectrophotometry Determination of Iron(II) Separated by Means of Adsorption of Its 3-(2-Pyridyl)-5, 6-Diphenyl-1, 2, 4-Triazine Complex with Tetraphenyl-Borate on Microcrystalline Naphthalene

A procedure is describe for the adsorption of ion-associated complex of iron(II) 3-(2-pyridyl)-5, 6-diphenyl-1, 2, 4-triazine (abbreviated as PDT) cation with tetra phenylborate (TPB) anion on macrocrystalline naphthalene. A water-insoluble ion-associated complex formed with PDT and TPB is quantitatively adsorbed on micro-crystalline naphthalene. The solid mixture containing the colored complex is dissolved in acetonitrile and the absorbance was measured at 553 nm. The other factors such as pH, amounts of reagents and naphthalene, shaking and standing times, diverse ions are studied. The method has been applied for the determination of iron in alloys and water samples.     

Flame atomic absorption spectrometric determination of trace chromium in various standard samples after preconcentration with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

Chromium can be quantitatively retained as 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-tetra-phenylborate(TPB) complex onto microcrystalline naphthalene in the pH range 4.8-5.9 from a large volume of aqueous solutions of various standard samples. After filtration, the solid mass consisting of the chromium complex and naphthalene was dissolved with 5 mL of dimethylformamide and the metal was determined by air-acetylene FAAS. A detection limit of 4 ng/mL for chromium was established. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of chromium in various standard alloys and biological samples.     

Nucleoside und Nucleotide. Teil 16. Verhalten von 1-(2′-Desoxy-β-D-ribofuranosyl)-2(1 H)-pyrimidinon-5′-triphosphat, 1-(2′-Desoxy-β-D-ribofuranosyl)-2(1 H)pyridinon-5′-triphosphat und 4-Amino-1-(2′-Desoxy-β-D-ribofuranosyl)-2(1 H)-pyridinon-5′-triphosphat gegenüber DNA-Polymerase

Nucleosides and Nucleotides. Part 16. The Behaviour of 1-(2′-Deoxy-β-D -ribofuranosyl)-2(1H)-pyrimidinone-5′-triphosphate, 1-(2′-Deoxy-β-D -ribofuranosyl-2(1H))-pyridinone-5′-triphosphate and 4-Amino-1-(2′-desoxy-β-D -ribofuranosyl)-2(1H)-pyridinone-5′-triphosphate towards DNA Polymerase The behaviour of nucleotide base analogs in the DNA synthesis in vitro was studied. The investigated nucleoside-5′-triphosphates 1-(2′-deoxy-β-D -ribofuranosyl)-2(1 H)-pyrimidinone-5′-triphosphate (pppM_d), 1-(2′-deoxy-β-D -ribofuranosyl)-2(1 H)-pyridinone-5′-triphosphate (pppII_d) and 4-amino-1-(2′-deoxy-β-D -ribofuranosyl)-2(1 H)-pyridinone-5′-triphosphate (pppZ_d) can be considered to be analogs of 2′-deoxy-cytidine-5′-triphosphate. However, their ability to undergo base pairing to the complementary guanine is decreased. When pppM_d, pppII_d or pppZ_d are substituted for pppC_d in the enzymatic synthesis of DNA by DNA polymerase no incorporation of these analogs is observed. They exhibit only a weak inhibition of the DNA synthesis. The mode of the inhibition is uncompetitive which shows that these nucleotide analogs cannot serve as substrates for the DNA polymerase.     

Dimethyl 2,2′‐bipyridine‐6,6′‐dicarboxylate and bis(dimethyl 2,2′‐bipyridine‐6,6′‐dicarboxylato‐κ2N,N′)copper(I) tetrafluoroborate

The single‐crystal X‐ray structures of dimethyl 2,2′‐bipyridine‐6,6′‐dicarboxylate, C₁₄H₁₂N₂O₄, and the copper(I) coordination complex bis(dimethyl 2,2′‐bipyridine‐6,6′‐dicarboxylato‐κ²N,N′)copper(I) tetrafluoroborate, [Cu(C₁₄H₁₂N₂O₄)₂]BF₄, are reported. The uncoordinated ligand crystallizes across an inversion centre and adopts the anticipated anti pyridyl arrangement with coplanar pyridyl rings. In contrast, upon coordination of copper(I), the ligand adopts an arrangement of pyridyl donors facilitating chelating metal coordination and an increased inter‐pyridyl twisting within each ligand. The distortion of each ligand contrasts with comparable copper(I) complexes of unfunctionalized 2,2′‐bipyridine.     

Nucleotides. Part XXXI. Modified Oligomeric 2′–5′ A Analogues: Synthesis of 2′–5′ oligonucleotides with 9-(3′-azido-3′-deoxy-β-D-xylofuranosyl)adenine and 9-(3′-amino-3′-deoxy-β-D-xylofuranosyl)adenine as modified nucleosides

A series of new 2′–5′ oligonucleotides carrying the 9-(3′-azido-3′deoxy-β-D-xylofuranosyl)adenine moiety as a building block has been synthesized via the phosphotriester method. The use of the 2-(4-nitrophenyl)ethyl (npe) and 2-(4-nitrophenyl)ethoxycarbonyl (npeoc) blocking groups for phosphate, amino, and hydroxy protection guaranteed straightforward syntheses in high yields and easy deblocking lo form the 2′–5′ trimers 21 , 22 , and 25 and the tetramer 23 . Catalytic reduction of the azido groups in [9-(3′-azido-3′-deoxy-β-D-xylofuranosyl)adenine]2′-yl-[2′-(O^p-ammonio)→ 5′]-[9-(3′-azido-3′-deoxy-β-D-xylofuranosyl)adenin]-2′-yl-[2′-(O^p-ammonio)→ 5′]-9-(3′-azido-3′-deoxy-β-D-xylofuranosyl)adenine ( 21 ) led to the corresponding 9-(3′-amino-3′-deoxy-β-D-xylofuranosyl)-adenine 2′–5′ trimer 26 in which the two internucleotidic linkages are formally neutralized by intramolecular betaine formation.     

Spirocyclization of 1-(o-aminophenyl)cycloalkanols and 1-(2′-amino-3′-pyridinyl)cycloalkanols

A one-step synthesis of spiro[cycloalkane-1,4′-2H-3′,1-benzoxazin]-2′-ones and spiro[cycloalkane-1,4′-1H-pyrido[2′,3′-d][1,3′]oxazin]-2′-ones, obtained in good yield from the corresponding 1-(o-aminophenyl) and 1-(2′-amino-3′-pyridinyl)cycloalkanols is described using ethyl carbonate in presence of n-butyllithium.