Serially coupled capillary columns supercritical fluid chromatography with midpoint pressure control

Two capillary columns of different polarities were coupled in series by means of a coupling restrictor. The pressure of the first column and the midpoint pressure (between the coupling restrictor and the second column) were controlled independently of each other using two pumps. The selectivity of this separation system was highly dependent on the pressure difference and could be continuously changed between those of two columns. The pressure difference could be changed even in course of separation for fine tuning of the selectivity. Several examples were shown to demonstrate the utility of this method.     

Selectivity optimization in liquid chromatography via stationary phase tuning

In striving for the best possible separation, the selectivity of stationary phases as an optimization parameter is often underestimated although there are many ways to influence this powerful tool. This review serves to provide an insight into the various ways of adapting the selectivity of a separation in liquid chromatography. Approaches via temperature and flow rate tuning are discussed as a basis followed by focusing on the stationary phase as the superior optimization parameter. Highly selective stationary phases hereby provide an advantage for groups of similar analytes. For more complex mixtures, separations can be improved using mixed-mode technologies where different retention mechanisms are combined. Serial coupling, mixed-bed columns, and stationary phase optimized selectivity liquid chromatography provide solutions to various degrees. Finally, the advantages of stationary phase tuning over adaption of mobile phase and/or temperature are presented in terms of optimum application range.     

Dual Fiber-In-capillary Annular Column with Ternary Stationary Phase for Gas Chromatographic Separation

In the present work a novel strategy for improving and/or tuning the selectivity of gas chromatographic (GC) separation by combining three different stationary phases (SPs) without premixing was introduced. A fused silica fiber coated with polydimethylsiloxane (SE30) and another coated with cyanopropylphenylmethylpolysiloxane (OV1701) were serially inserted into an 8-m polyethylene glycol 20 M (PEG20M) capillary column to form a GC annular column with ternary SP, abbreviating as SE30-OV1701-CF/PEG20M-CC. The separation capability of this ternary SP annular column was compared with a SE30-coated fiber-in-PEG20M-coated capillary annular column and a PEG20M-coated open tubular column by a test mixture of 19 organic compounds. Among these three columns, SE30-OV1701-CF/PEG20M-CC produced the best separation when the SE30-coated fiber and OV1701-coated fiber was 3 and 5 m, respectively. Selectivity can be easily tuned by changing the length of the SP-coated fibers in the ternary SP annular column. The proposed ternary SP annular column shows additional tunability, thus making it a promising tool for separation of organic solvents that are often used in the manufacturing process of pharmaceutical formulations and lacquer thinners.     

Synthesis and characterization of novel polar-embedded silica stationary phases for use in reversed-phase high-performance liquid chromatography

We have developed a series of new C₁₀ dipeptide stationary phases via a simple and effective synthetic method. The preparation of the new phases involves the synthesis of silanes and the surface modification of silica. Chromatographic evaluations of these columns were performed using the Engelhardt, Tanaka, and Neue test mixtures. The applicability of these new stationary phases was also evaluated using a series of diagnostic probes including acids, bases or neutral compounds and several generic applications. These new C₁₀ dipeptide stationary phases showed excellent hydrolytic stability over a wide pH range. Like other existing amide-embedded columns, these new stationary phases exhibit higher retention for polar and hydrophilic compounds and different selectivity as compared to conventional C₁₈ columns. These new phases are compatible with 100% aqueous mobile phases, and also provide high column efficiency and good peak shapes for both acidic and basic compounds.     

Flexible soft glass capillary columns vs. flexible fused silica capillary columns for gas chromatography-a critique

The gas chromatographic use of flexible thin walled soft glass capillary columns coated with non-polar stationary phases is compared to similar columns made of fused silica glass. With non-polar soft glass columns, the use of surface roughening viagaseous HCI followed by a Carbowax 20 M pretreatment gave adsorptive phenomena, and thermal instability. With very polar soft glass columns where a variety of cyanopropyl silicone phases were coated directly onto the NaCI crystal matrix, adsorptive effects were again prominent and frequent break-down in film stability with time, was also observed. These undesirable effects were due to the presence of metal oxides in the soft glass. Attempts to remove these materials from the thin walled soft glass surface by means of acid leaching produced significant brittleness. This deleterious result was further increased by attempts at high temperature silylation or polysiloxane deactivation. In sharp contrast, the fused silica surface was essentially free of metal oxides and the surface silanol groups are easily neutralized by silylation or polysiloxane deactivation techniques. No brittleness was observed following these procedures. An increasing series of high molecular weight, viscous, polymeric vinyl containing non-polar and highly polar stationary phases have been produced which readily wet the surface of the fused silica and are easily crosslinked in the presence of free radical generators. These columns are essentially free of all the problems noted with flexible thin walled soft glass. When all of the parameters involved in the fabrication of a glass capillary column are assessed, it appears at this time, that the flexible fused silica glass column with cross linked phases approaches the “ideal” capillary column.     

Gas chromatography of fatty acids.

Lipids in foods contain a wide variety of fatty acids differing in chain length, degree of unsaturation, position and configuration of double bonds and the presence of special functional groups. Modern capillary gas chromatography offers excellent separation of fatty acids. Fused-silica capillary columns with stationary phases of medium polarity and non-polar methylsilicone stationary phases successfully separate most of the natural fatty acids. Special applications, such as the separation of complex cis-trans fatty acid mixtures and cyclic fatty acids, required particular chromatographic conditions, including the use of very long capillary columns or more polar stationary phases. The derivatization methods for the preparation of fatty acid esters also need to be optimized to obtain accurate quantitative results. This paper reviews the derivatization techniques, capillary columns and stationary phases commonly used in the gas chromatography of fatty acids in food.     

Ligand Exchange Gas Chromatography on PTFE Open Tubular Columns

Two kinds of capillary columns were prepared and tested as the stationary phases of ligand exchange gas chromatographic separation of dialkyl sulfides. The PTFE column wall-coated with silane-DTC-Cu but without the addition of silicone exhibits significantly better selectivity towards dialkyl sulfides than a column wall-coated with 10% silane-DTC-Cu in silicone. With the first column connected to a microsample injection valve and a microsample loop, the quantitative determination of dialkyl sulfides can be performed. The column also shows great promise for the separation of dialkyl sulfide-hydrocarbon mixtures.     

Investigation of polar stationary phases for the separation of sympathomimetic drugs with nano-liquid chromatography in hydrophilic interaction liquid chromatography mode

In this study, the retention and selectivity of a mixture of basic polar drugs were investigated in hydrophilic interaction chromatographic conditions (HILIC) using nano-liquid chromatography (nano-LC). Six sympathomimetic drugs including ephedrine, norephedrine, synephrine, epinephrine, norepinephrine and norphenylephrine were separated by changing experimental parameters such as stationary phase, acetonitrile (ACN) content, buffer pH and concentration, column temperature. Four polar stationary phases (i.e. cyano-, diol-, aminopropyl-silica and Luna HILIC, a cross-linked diol phase) were selected and packed into fused silica capillary columns of 100 μm internal diameter (i.d.). Among the four stationary phases investigated a complete separation of the all studied compounds was achieved with aminopropyl silica and Luna HILIC stationary phases only. Best chromatographic results were obtained employing a mobile phase composed by ACN/water (92/8, v/v) containing 10 mM ammonium formate buffer pH 3. The influence of the capillary temperature on the resolution of the polar basic drugs was investigated in the range between 10 and 50 °C. Linear correlation of ln k vs. 1/T was observed for all the columns; ΔH° values were negative with Luna HILIC and positive with aminopropyl- and diol-silica stationary phases, demonstrating that different mechanisms were involved in the separation.To compare the chromatographic performance of the different columns, Van Deemter curves were also investigated.     

Advances in sol-gel based columns for capillary electrochromatography: sol-gel open-tubular columns

The development of sol-gel open-tubular column technology in capillary electrochromatography (CEC) is reviewed. Sol-gel column technology offers a versatile means of creating organic-inorganic hybrid stationary phases. Sol-gel column technology provides a general approach to column fabrication for microseparation techniques including CEC, and is amenable to both open-tubular and monolithic columns. Direct chemical bonding of the stationary phase to the capillary inner walls provides enhanced thermal and solvent stability to sol-gel columns. Sol-gel stationary phases inherently possess higher surface area, and thus provide an effective one-step alternative to conventional open-tubular column technology. Sol-gel column technology is applicable to both silica-based and transition metal oxide-based hybrid stationary phases, and thus, provides a great opportunity to utilize advanced material properties of a wide range of nontraditional stationary phases to achieve enhanced selectivity in analytical microseparations. A wide variety of stationary phase ligands can be chemically immobilized on the capillary inner surface using a single-step sol-gel procedure. Sol-gel chemistry can be applied to design stationary phases with desired chromatographic characteristics, including the possibility of creating columns with either a positive or a negative charge on the stationary phase surface. This provides a new tool to control electroosmotic flow (EOF) in the column. Column efficiencies on the order of half a million theoretical plates per meter have been reported for sol-gel open-tubular CEC columns. The selectivity of sol-gel stationary phases can be easily fine-tuned by adjusting the composition of the coating sol solution. Open-tubular columns have significant advantages over their packed counterparts because of the simplicity in column making and hassle-free fritless operation. Open-tubular CEC columns possess low sample capacity and low detection sensitivity. Full utilization of the analytical potential of sol-gel open-tubular columns will require a concomitant development in the area of high-sensitivity detection technology.     

Stimultaneous quantitative analysis using dual capillary columns of different polarities

Complex organic mixtures, such as coal liquefaction and oil shale products and by-products, are comprised of hundreds or thousands of individual components. State-of-the-art high resolution gas chromatography does not always provide sufficient resolution to allow accurate quantitation or identification of many compounds of interest. The concept of dual capillary column chromatography combines the different resolving characteristics of two capillary columns coated with different stationary phases into a single chromatographic run. In this approach, both columns are connected to the same injection port. Analysis of complex mixtures in this fashion can confirm the identification and quantitation of components on two columns of different polarity with little increased analysis time, can provide a means of obtaining quantitative data for individual components which are known to coelute on any one column, and can alert one to unknown coelution problems that would be undetected by gas chromatographic analysis on a single capillary column. Simultaneous dual column analysis was applied to three samples, the neutral polycyclic aromatic hydrocarbon (PAH) fraction of a Solvent Refined Coal-II (SRC-II) heavy distillate, the nitrogen-containing polycyclic aromatic compound (N-PAC) fraction of an SRC-II heavy distillate, and the basic fraction from a shale oil process water. Fused silica capillary columns coated with SE-54 and Durawax 3 were used for the analyses of the heavy distillate, while SE-54 an Carbowax 20M capillary columns were used for the analysis of the process water.     

A protocol for fabrication of polymer monolithic capillary columns and tuning the morphology targeting high-resolution bioanalysis in gradient-elution liquid chromatography

Polymer monolithic stationary phases are designed as a continuous interconnected globular material perfused by macropores. Like packed column, where separation efficiency is related to particle diameter, the efficiency of monoliths can be enhanced by tuning the size of both the microglobules and macropores. This protocol described the synthesis of poly(styrene-co-divinylbenzene) monolithic stationary phases in capillary column formats. Moreover, guidelines are provided to tune the macropore structure targeting high-throughput and high-resolution monolith chromatography. The versatility of these columns is exemplified by their ability to separate tryptic digests, intact proteins, and oligonucleotides under a variety of chromatographic conditions. The repeatability of the presented column fabrication process is demonstrated by the successful creation of 12 columns in three different column batches, as evidenced by the consistency of retention times (coefficients of variance [c.v.] = 0.9%), peak widths (c.v. = 4.7%), and column pressures (c.v. = 3.1%) across the batches.     

The optimization of capacity and efficiency when coupling fused silica open tubular columns in gas chromatography

Summary There are a number of parameters which have to be chosen depending on the analysis being done in gas chromatography. While the choice of stationary phase material is based on the solutes to be separated, the thickness is dependent on the concentration and the volatility of the components to be analyzed. This study undertakes a coupled column phase ratio optimization by connecting a short piece of a particular column prior to a normal length of an analytical column. Various columns of different dimensions (phase ratio), but of the same stationary phase material (methyl silicone), are coupled together by a deactivated glass press-fit connector, and the efficiency and capacity are measured. The coupling of fused silica open tubular columns is optimized in efficiency by matching or decreasing the phase ratio of successive columns. Capacity optimization is accomplished by increasing the phase ratio of consecutive columns. Capacity and efficiency optimization are opposing each other; therefore, if some efficiency can be sacrificed a substantial increase in capacity is possible.     

Enantioseparations by capillary electro-chromatography: differences exhibited by normal- and reversed-phase versions of polysaccharide stationary phases

The influence of using normal-phase and reversed-phase versions of four commercial polysaccharide stationary phases on chiral separations was investigated with capillary electrochromatography (CEC). Both versions of the stationary phases, Chiralcel OD, OJ, and Chiralpak AD, AS were tested for the separation of two basic, two acidic, a bifunctional, and a neutral compound. Different background electrolytes were used, two at low pH for the acid, bifunctional and neutral substances, and three at high pH for the basic, bifunctional and neutral ones. This setup allowed evaluating differences between both stationary-phase versions and between mobile-phase compositions on a chiral separation. Duplicate CEC columns of each stationary phase were in-house prepared and tested, giving information about the intercolumn reproducibility. In general, reversed-phase versions of the current commercial polysaccharide stationary phases are found to be best for reversed-phase CEC, even though at high pH no significant differences were seen between both versions. Most differences were observed at low pH. For acidic compounds, it was seen that an ammonium formate electrolyte performed best, which is also an excellent electrolyte if coupling with mass spectrometry is desired. For basic, bifunctional and neutral compounds, no significant differences between the three tested electrolytes were observed at high pH. Here, a phosphate buffer is preferred as electrolyte because of its buffering capacities. However, if coupling to mass spectrometry is wanted, the more volatile ammonium bicarbonate electrolyte can be used as an alternative.     

气相色谱近年的发展

简要阐述了近几年气相色谱(GC)的发展和特点。GC是一个成熟的技术,广泛地应用于各个领域,近几年GC的发展除了继续研究新的固定相和高性能的毛细管色谱柱之外,主要在全二维气相色谱(GC×GC)、快速GC、便携式GC仪和微型GC仪几个方面。近几年新研究的GC固定相主要集中在常温离子液体和各种环糊精的衍生物。现在GC研究者趋向于使用商品化的GC毛细管柱,而商品化的GC毛细管柱应用最多的是以含5%苯基的聚甲基硅氧烷为固定相的色谱柱。GC×GC发展迅猛,特别是关于调制器的研究,已开发出十多种调制模式,并广泛地应用于各个领域。为了适应大量样品的分析和现场分析,研究和开发了多种快速GC方法和仪器以及便携式GC仪。为了仪器的小型化和专属性检测,μGC仪的研究也稳步地发展起来。     

Crosslinked methylphenylsilicones as stationary phases for capillary gas chromatography

Summary Methyl(phenyl)silicones offer useful selectivities when used as stationary phases in gas chromatography (GC). Such phases have, however, hitherto been of restricted importance in capillary GC due to the lack of phases having a viscosity high enough to ensure stationary phase film stability. Further, to utilize fully the possibilities of a methyl(phenyl)silicone capillary column, it must also possess high efficiency and a high degree of deactivation.In this work, the preparation of soda-glass capillary columns coated within situ cured methyl(phenyl) and methyl(tolyl)-silicones is presented. Vulcanization was made possible by the introduction of some vinyl substitution in the gum to be cured: tolyl-containing gums could be cured without the presence of vinyl groups. In addition, fused silica capillary columns coated with OV-1701 were prepared.The columns show a coating efficiency of above 80%, a thermal stability up to 320 °C and a high degree of deactivation. Their utility is demonstrated by the separation of samples containing polynuclear aromatics, antidepressants and some potent mutagens.Presented at the 14th International Symposium on Chromatography London, September, 1982     

OH-terminated cyanopropyl silicones

Due to their high polarity and unique selectivity, cyanopropyl silicones are basic stationary phases for high resolution capillary gas chromatography. Different OH-terminated cyanopropyl silicones, containing a high cyanopropyl content, were synthesized and chromatographically evaluated. Special attention was paid to the degree of immobilization of the phases in FSOT columns. Depending on the problem at hand, a choice has to be made between immobilization and maximum selectivity.     

Capillary liquid chromatography as a tool for separation of hydrophobic basic drugs. Relation between tests for column characterization and real analysis

Two capillary columns for reversed phase (RP) capillary liquid chromatography (CLC), viz. Nucleosil 100‐5 C18 and LiChrosorb RP‐select B, were characterized by the Walters test, i.e. the chromatographic test proposed for RP stationary phases. Hydrophobicity indices were determined not only in acetonitrile/water mobile phase, as proposed in the test, but they were also measured in buffered systems. This approach was used to quantify the influence of mobile phase composition on the modification of the surface of the stationary phases. In the next step, small basic compounds differing in their hydrophobicity and basicity were selected and their retention on the stationary phases in mobile phases of the same composition as used for column testing was examined. Furthermore, the retention of newly synthesized drugs, chemotherapeutics derived from thioacridine and pyridoquinoline, differing in their structures, basicity, and hydrophobicity, was also studied. The composition of the mobile phases had to be shifted to higher contents of organic modifiers – acetonitrile or methanol – in order to elute these hydrophobic compounds from the columns. The question we wanted to answer was: How is the method for testing of reversed phases related to retention, separation efficiency, and peak symmetry of various analytes?     

A technique for coating capillary columns with a very thick film of cross-linked stationary phase

A method for preparation of capillary columns and traps with a very thick film (up to 100 μm) of stationary phase is described. The principle of this method is based on an immediate fixation of a film of prepolymer, formed during dynamic coating. Thus, the development of film irregularities, such as are caused by Rayleigh instability is avoided. Fixation of the film is conveniently accomplished by heat-accelerated crosslinking as was demonstrated in this work, where a commercially available silicone prepolymer (Sylgard 184, Dow Corning) was employed. The low phase ratio columns which thus can be prepared are interesting both in chromatography with dense mobile phases and as enrichment devices. Examples of the latter application are shown, where trace organic components from air and water were concentrated.     

Monolithic enantiomer-selective stationary phases for capillary electrochromatography

Monolithic materials have become a well-established format for stationary phases in the field of capillary electrochromatography. Four types of monoliths, namely particle-fixed, silica-based, polymer-based, and molecularly imprinted monoliths, have been utilized as enantiomer-selective stationary phases in CEC. This review summarizes recent developments in the area of monolithic enantiomer-selective stationary phases for CEC. The preparative procedure and the characterization of these columns are highlighted. In addition, the disadvantages and limitations of different monolithic enantiomer-selective stationary phases in CEC are briefly discussed.     

高分子冠醚毛细管柱的性能研究

本文报道了3种新的聚硅氧烷侧链冠醚作气相色谱固定液,并涂渍成弹性石英毛细管柱,这种毛细管柱具有优良的色谱性能,它们具有柱效高,热稳定性好,选择性强的特点,适于分离各种异构体。