Wetting and adsorption: II. Adsorption of Triton X-100 and Triton X-305 onto carbon black from water and cyclohexane solutions

The adsorption isotherms of nonionic surfactants Triton X-100 and Triton X-305 from water and cyclohexane on carbon black have been determined at 15 and 30°C. The Langmuir-type and BET-type isotherms are obtained for adsorption of Triton X-100 and Triton X-305 from water and cyclohexane respectively. Both the contact angles of water for graphite/water/air and graphite/water/cyclohexane decrease monotonously with increasing surfactant concentration. From these results, it is proposed that the adsorption of Triton X-100 and Triton X-305 on carbon black or graphite from water is monolayer. For the adsorption from cyclohexane solutions, the ethyleneoxide group of the surfactant molecules may be adsorbed onto the polar spot at the surface of carbon black, and the hydrophobic group of adsorbed molecules may direct toward the liquid phase or attaches to the nonpolar surface region around the polar spot. As the concentration increases, the ethylene oxide groups of the adsorbed molecules can be aggregated with each other via polar interactions to form hemi-reversed micelle.     

吸附与润湿II.Triton X-100和Triton x-305在炭黑/水和炭黑/环己烷界面上的吸附层结构

测定了15℃和30℃时炭黑自水和环己烷中吸附非离子型表面活性剂TritonX-100和Triton X-305的等温线;计算了吸附过程的标准热力学函数;测定了石墨/水/环己烷和石墨/水/空气的接触角与表面活性剂浓度的关系, 分析所得结果,可得结论:在炭黑/水或石墨/水界面上,Triton型表面活性分子形成单分子吸附层,分子以憎水的iso-C8H17C6H4基团附着在表面,而以亲水的聚氧乙烯链伸入水相的方式取向;在炭黑/环已烷或石墨/环己烷界面上,分子是通过聚氧乙烯链吸附到表面上的,当浓度增加时分子在表面可能通过聚氧乙烯链间的相互作用而发生聚集,即可能形成表面反式胶团。     

Electrokinetic characterization of polystyrene–non-ionic surfactant complexes

An experimental study on the electrophoretic mobility (μ_e) of polystyrene particles after the adsorption of non-ionic surfactants with different chain lengths is described. Two sulphate latexes with relatively low surface charge densities (3.2 and 4.8 μC cm⁻²) were used as solid substrate for the adsorption of four non-ionic surfactants, Triton X-100, Triton X-165, Triton X-305 and Triton X-405, each one with 9–10, 16, 30 and 40 molecules of ethylene oxide (EO), respectively. The electrophoretic mobility of the polystyrene–non-ionic surfactant complexes was studied versus the amount of adsorbed surfactant (Γ). The presence of non-ionic surfactant onto particles surface seems to produce a slight shifting of the slipping plane because the mobilities of the different complexes display a very small decreasing. The increase in the number of EO chains in the surfactant molecule seems to operate as a steric impediment which decreases the number of adsorbed large surfactant molecules. The electrophoretic mobilities of the latex–surfactant complexes with maximum adsorption were measured versus the pH and ionic strength of the dispersion. While the different complexes showed a similar qualitative behaviour compared with that of the bare latex against the pH, the adsorption of the surfactant reduces the typical maximum in the μ_e−log[electrolyte].     

Effect of inorganic positive ions on the adsorption of surfactant Triton X-100 at quartz/solution interface

The electrode-separated piezoelectric sensor (ESPS), an improved setup of quartz crystal microbalance (QCM), has been employed to investigate the adsorption behavior of nonionic surfactant Triton X-100 at the hydrophilic quartz-solution interface in mineralized water medium in situ, which contained CaCl2 0.01 mol·L?1, MgCl2 0.01 mol·L?1, NaCl 0.35 mol·L?1. In a large scale of surfactant concentration, the effects of Ca2 , Mg2 and Na on the adsorption isotherm and kinetics are obviously different. In aque-ous solution containing NaCl only, adsorption of Triton X-100 on quartz-solution interface is promoted, both adsorption rate and adsorption amount increase. While in mineralized water medium, multivalent positive ions Ca2 and Mg2 are firmly adsorbed on quartz-solution interface, result in the increasing of adsorption rate and adsorption amount at low concentration of surfactant and the peculiar desorption of surfactant at high concentration of Triton X-100. The results got by solution depletion method are in good agreement with which obtained by ESPS. The "bridge" and "separate" effect of inorganic positive ions on the adsorption and desorption mechanism of Triton X-100 at the quartz- solution interface is discussed with molecular dynamics simulations (MD), flame atomic absorption spectrometry (FAAS) and atomic force microscopy (AFM) methods.     

Effects of surfactant/water ratio and dye amount on the fluorescent silica nanoparticles

Effects of surfactant/water volume ratios and dye amounts on the properties of micelles and fluorescence silica nanoparticles were studied in microemulsions containing nonionic surfactant Triton X-100, hexanol as co-surfactant, cyclohexane as organic solvent, and metal organic dye (tris(2,2′-bipyridyl)dichlororuthenium) via fluorescence probe technique, TEM, and XPS. Fluorescence probe measurements show that the micelle microenvironment becomes stable at the surfactant/water volume ratio higher than 3.5 and the incubation time longer than 10 h. The data suggest that the silica shell, which is formed at the surfactant/water ratio of 3.5, yields an efficient protection of dye molecules against the e-beam irradiation and result in high photostability of fluorescent silica. We pioneered the localization of dye molecules on the surface of dye-doped silica and found that an increase of dye amounts, beyond a threshold, in the microemulsion cannot enhance the fluorescence intensity of dye-doped nanoparticles. These results are of significant importance for optimizing the synthesis of fluorescent nanoparticles with high photostability and low cost.     

Influence of Surfactants Synergism on the Adsorption Behavior at Air/Water and Solid/Water Interfaces

The influence of synergistic interaction between sodium dodecylsulfate (SDS) and N,N-dimethyldodecan-1-amine oxide (DDAO) on their adsorption at air/water and solid/water interfaces at 20°C is investigated. The critical micelle concentration values obtained from surface tension measurements indicated strong synergism between SDS and DDAO, according to regular solution model. The excess surface concentration (Γ) and the minimum occupied area by single and mixed surfactant monomers (A_min) at liquid/air interface were also calculated. The adsorption onto the activated charcoal and silica was then measured to find out the correlation between surfactant synergism and their adsorption at solid/water interface. The amounts of surfactant adsorbed onto 1 wt% activated charcoal follow the trend: SDS/DDAO > DDAO > SDS. SDS molecules do not adsorb onto 5 wt% silica substrate, while SDS/DDAO mixed system was found to have the highest adsorption behavior. The obtained indicate that SDS can be removed from water by mixing it with amphoteric surfactant.     

Partitioning behavior of silica in the Triton X-100/dextran/water aqueous biphasic system

The partitioning behavior of silica particles was investigated in the Triton X-100/dextran/water system. It was found that both electrostatic effects and interactions between phase-component species and the solid surface played important roles in determining the distribution of solids. Silica partition was highly pH-dependent, which was interpreted in terms of the pH dependence of the Triton X-100/SiO(2) interaction and the weak acidity of dextran. The presence of sodium dodecyl sulfate (SDS) moved the particles from the top surfactant-rich phase to the interface and the bottom phase, while dodecyltrimethylammonium bromide (DTAB) had the opposite effect. These trends are attributable to the electrostatic interaction between the charged mixed micelles in the top phase and the particles and to the fact that the ionic surfactants modified the adsorption density of the nonionic surfactant on silica.     

Adsorptive modification of hydrophobic solid surfaces by mixed surfactant solutions

We studied the reciprocal influence of a nonionic surfactant (triton X-305) and a cationic surfactant (tetradecyltrimethylammonium bromide; TTAB) on their adsorption from aqueous solution on hydrophobic glass, interfacial tension at the solution/solid interface, composition of the mixed adsorption layer, and interaction parameters between surfactant molecules in mixed adsorption layers.     

Adsorption Kinetics of Some Polyethylene Glycol Octylphenyl Ethers Studied by the Fast Formed Drop Technique

The adsorption kinetics of Triton X-100 and Triton X-405 at solution/air and solution/hexane interfaces is studied by the recently developed fast formed drop technique. The dynamic interfacial tension of Triton X-100 and Triton X-405 solutions against hexane has been measured without preequilibration of the water and oil phases. It is found that the dynamic interfacial tension of Triton X-100 solutions passes through a minimum. This strange behavior is attributed to partial solubility of the surfactant in hexane. Such minima of the dynamic interfacial tension of Triton X-405 solutions have not been observed, which correlates well with the solubilities of both surfactants in hexane reported in the literature. The dynamic surface tension of solutions of both surfactants and the dynamic interfacial tension of Triton X-405 solutions are interpreted by the Ward and Tordai model for diffusion controlled adsorption. It is shown that proper interpretation of the experimental data depends on the type of isotherm used. More consistent results are obtained when the Temkin isotherm is used instead of the Langmuir isotherm. The results obtained with Triton X-100 at the solution/air interface confirm that the adsorption of this surfactant occurs under diffusion control. The adsorption of Triton X-405 at solution/air and at solution/hexane interfaces seems to occur under diffusion control at short periods of time, but under mixed (diffusion-kinetic) control at long periods of time. A hypothesis is drawn to explain this phenomenon by changes in the shape of the large hydrophilic heads of Triton X-405 molecules. Copyright 2000 Academic Press.     

Equilibrium contact angles as a function of the concentration of nonionic surfactants on quartz plate

The contact angles of aqueous solution of Triton X-100 and Triton X-305 for airwater-quartz and cyclohexane-water quartz systems have been studied. It has been found that the equilibrium contact angle (measured through water) against quartz is increased by the addition of small amounts of nonionic surfactants, but beyond a certain concentration the angle decreases again. Based on the bilayer adsorption model on quartz/water interface, the experimental results can be explained.     

Surface Property of Nonionic Surfactant Triton X-100 in an Ionic Liquid

A common nonionic surfactant Triton X-100 was dissolved in a commercial ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF₄). The surface tension of the bmimBF₄ solution was decreased with increasing the content of surfactant Triton X-100, a similar phenomenon with aqueous solution systems. Dynamic surface properties of Triton X-100 in bmimBF₄ were measured. It was found that pure IL solvents need rearrangement at the air-bmimBF₄ interface during the beginning stage of absorption. Moreover, the adsorption model was found to be in accord with the diffusion-controlled adsorption mechanism, and further, the dilute bmimBF₄ solutions are close to the diffusion-controlled adsorption.     

Adsorption Properties of Hydrocarbon and Fluorocarbon Surfactants Ternary Mixture at the Water-Air Interface

Measurements were made of the surface tension of the aqueous solutions of p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethylene glycols) having 10 oxyethylene groups in the molecule (Triton X-100, TX100) and cetyltrimethylammonium bromide (CTAB) with Zonyl FSN-100 (FC6EO14, FC1) as well as with Zonyl FSO-100 (FC5EO10, FC2) ternary mixtures. The obtained results were compared to those provided by the Fainerman and Miller equation and to the values of the solution surface tension calculated, based on the contribution of a particular surfactant in the mixture to the reduction of water surface tension. The changes of the aqueous solution ternary surfactants mixture surface tension at the constant concentration of TX100 and CTAB mixture at which the water surface tension was reduced to 60 and 50 mN/m as a function of fluorocarbon surfactant concentration, were considered with regard to the composition of the mixed monolayer at the water-air interface. Next, this composition was applied for the calculation of the concentration of the particular surfactants in the monolayer using the Frumkin equation. On the other hand, the Gibbs surface excess concentration was determined only for the fluorocarbon surfactants. The tendency of the particular surfactants to adsorb at the water-air interface was discussed, based on the Gibbs standard free energy of adsorption which was determined using different methods. This energy was also deduced, based on the surfactant tail surface tension and tail-water interface tension.     

(Ba, Sr)TiO3纳米棒的反相微乳法制备与表征

在氢氧化钡和氢氧化锶水溶液/Triton X-100/环己烷/正己醇四元W/O型反相微乳液中制备了钛酸锶钡纳米棒, 研究了ω₀值(水与表面活性剂Triton X-100的物质的量之比)、反应物浓度、陈化时间对产品形貌和尺寸的影响, 用TEM, SAED, SEM, EDS和XRD等技术对产品进行了表征. 结果表明, 所得Ba_0.7Sr_0.3TiO₃纳米棒长约500～1200 nm、直径约为50～120 nm; 具有立方相单晶结构. 产品中钡、锶、钛的物质的量之比约为0.7∶0.3∶1.     

Role played by the head size of some non‐ionic surfactants on their adsorption onto montmorillonite clay

Sorption behavior of polyoxethylene(n)monooleate series [Ol(EO)_n] onto montmorillonite clay was studied at 25°C to investigate the influence of the surfactant's head size on the sorption process. All the tested surfactants exhibited L‐shaped isotherms that means a strong interaction between the adsorbent and the adsorbate. Also, all the obtained isotherms ended with a drastic increase in the isotherm slope at nearly constant equilibrium concentration. This abrupt increase reflected the fairly high affinity of the tested surfactants to the clay surface at high bulk concentration region. The maximum amount adsorbed at the plateau region, Γ_max, was calculated according to the Langmuir adsorption theory and followed the order: Ol(EO)₁₄ > Ol(EO)₂₀ < Ol(EO)₄₀ < Ol(EO)₈₀. In case of short ethylene oxide (EO) chain, Γ_max decreased with the increase in the chain length; but a reverse result was obtained in case of surfactants with longer EO chain length (20 to 80 units). The free energy of adsorption, ΔG°_ad, had negative values indicating the spontaneous adsorption of surfactant molecules onto clay. The values of ΔG°_ad increased with increasing EO units from 14 to 20 units and decreased with further elongation in the EO chain from 20 to 80 units. Copyright © 2004 John Wiley & Sons, Ltd.     

Temperature induced phase separation of luminescent silica nanoparticles in Triton X-100 solutions

The aggregation and cloud point behavior of Tb(III)-doped silica nanoparticles has been studied in Triton X-100 (TX-100) solutions at various concentration conditions by fluorimetry, dynamic light scattering, electrophoresis and transmission electron microscopy methods. The temperature responsive behavior of nanoparticles is observed at definite concentration of TX-100, where the aggregation of TX-100 at the silica/water interface is evident from the increased size of the silica nanoparticles. The reversible dehydration of TX-100 aggregates at the silica/water interface should be assumed as the main reason of the temperature induced phase separation of silica nanoparticles. The distribution of nanoparticles between aqueous and surfactant rich phases at the phase separation conditions can be modified by the effect of additives.     

Molecular behavior and synergistic effects between sodium dodecylbenzene sulfonate and Triton X-100 at oil/water interface

Significant synergistic effects between sodium dodecylbenzene sulfonate (SDBS) and nonionic nonylphenol polyethylene oxyether, Triton X-100 (TX-100), at the oil/water interface have been investigated by experimental methods and computer simulation. The influences of surfactant concentration, salinity, and the ratio of the two surfactants on the interfacial tension were investigated by conventional interfacial tension methods. A dissipative particle dynamics (DPD) method was used to simulate the adsorption properties of SDBS and TX-100 at the oil/water interface. The experiment and simulation results indicate that ultralow (lower than 10(-3) mN m(-1)) interfacial tension can be obtained at high salinity and very low surfactant concentration. Different distributions of surfactants in the interface and the bulk solution corresponding to the change of salinity have been demonstrated by simulation. Also by computer simulation, we have observed that either SDBS or TX-100 is not distributed uniformly over the interface. Rather, the interfacial layer contains large cavities between SDBS clusters filled with TX-100 clusters. This inhomogeneous distribution helps to enhancing our understanding of the synergistic interaction of the different surfactants. The simulation conclusions are consistent with the experimental results.     

On the Behavior of Nonionic Surfactants at the N-Heptane/Silica Gel Interface: Influence of the Presence of Interfacial Water Inferred from Adsorption Isotherms and Calorimetric Data

The behavior of two polydisperse nonionic surfactants, poly (oxyethylene) glycol alkylphenyl ether TX-35 and TX-100, at the prewetted silica gel/n-heptane and dried silica gel/n-heptane interfaces has been compared by the determination of the average adsorption isotherms of the polydisperse surfactants and of displacement enthalpies. From HPLC experiments, we could also separately quantify the adsorption of each ethyleneoxide (EO) fractions for silica gel from the polydisperse surfactant solution. The adsorption isotherms clearly indicate an incomplete preferential adsorption of the large (EO) chains over the small ones, as well on dried silica gel as on a prehydrated sample. This preferential adsorption and its driving force follow the solubility rules of the poly(oxyethylene) glycol alkylphenyl ether in an apolar solvent and support the idea of a solubility-limited adsorption: solubility in organic solvents of the smaller (EO) chains is much more significant than that of the longer ones and hence prevents adsorption of the smaller species. Consequently, it is observed that the presence of interfacial water decreases the affinity of TX-35 molecules for the hydrophilic silica surface due to the hydration of (EO) chains. In contrast, for TX-100 adsorption after the prewetting treatment the clearest trend is a drastic increase of the adsorption ascribed to the additional solubilization (and micellization) of the TX-100 molecules in the interfacial aqueous phase. The differential molar enthalpies of displacement show a change in the adsorption mechanism, depending on the presence of molecular water on the surface. In the initial part of the adsorption isotherm, a prevailing exothermic process is obtained with prehydrated silica and suggests that hydration of the polar heads of TX-35 and the solubilization of the TX-35 in interfacial water are occurring. For higher equilibrium concentrations, the enthalpies of displacement observed with the prehydrated adsorbent become slightly lower than those obtained with dry silica gel. It may be that this difference is due to the micellization phenomenon of the surfactant species with longer EO chains in interfacial water. These features emphasize the influence of interfacial water on the adsorption of EO fractions from organic solvent. Copyright 2000 Academic Press.     

Assembly properties of Triton X-100/phosphatidylcholine aggregates during liposome solubilization

The assembly properties of the nonionic surfactant Triton X-100 and phosphatidylcholine (PC) aggregates during the overall solubilization process of PC liposome were investigated. Permeability alterations were detected as a change in 5(6)-carboxyfluorescein (CF) released from the interior of vesicles and bilayer solubilization as a decrease in the static light scattered by liposome suspensions. A direct dependence was established between the bilayer/aqueous phase surfactant partition coefficients (K), the growth of vesicles and the leakage of entrapped CF in the initial interaction steps (surfactant to phospholipid molar ratioRe up to 0.2). These changes may be related to the increasing presence of surfactant molecules in the outer monolayer of vesicles. In theRe range 0.2–0.35 the coexistence of a low vesicle growth with a constant increase of CF release may be correlated with the decrease inK (increased rate of flip-flop of surfactant molecules). Furthermore, in theRe range between 0.64 and 2.0 (lytic levels) almost a linear dependence was detected between the composition of these aggregates (Re) and the decrease in both the surfactant-PC aggregate size and the static light scattered by the system. This dependence was not observed in the last solubilization steps (Re range 2.0–2.60) possibly due to the increased formation of mixed micelles in this interval. The fact that the free Triton X-100 concentration at sublytic and lytic levels showed respectively lower and similar values than its critical micelle concentration confirms that permeability alterations and solubilization were determined respectively by the action of surfactant monomer and by the formation of mixed micelles.Abbreviations PC phosphatidylcholine - PIPES piperazine-1,4 bis(2-ethanesulphonic acid) - T_X-100 Triton X-100 - CF 5(6)-carboxyflucrescein - Re enective surfactant/lipid molar ratio - Re _SAT effective surfactant/lipid molar ratio for bilayer saturation - Re _SOL enective surfactant/lipid molar ratio for bilayer solubilization - S _W surfanctant concentration in the aqueous medium - S _B surfactant concentration in the bilayers - S _T total surfactant concentration - K bilayer/aqueous phase surfactant partition coefficient - K _SAT bilayer/aqneous phase surfactant partition coefficient for bilayer saturation - K _SOL bilayer/aqueous phase surfactant partition coefficient for bilayer solubilization - PL phospholipid - TLC-FID thinlayer chromatography/flame ionization detection system - PI polydispersity index - CMC critical micellar concentration - r ² regression coefficient     

Self-aggregation and supramolecular structure investigations of Triton X-100 and SDP2S by NOESY and diffusion ordered NMR spectroscopy

The self-aggregation and supramolecular micellar structure of two surfactants in aqueous solution, the anionic surfactant SDP2S (sodium dodecyl dioxyethylene-2 sulfate) and the nonionic surfactant Triton X-100 (octylphenol-polyoxyethylene ether with 9.5 ethoxy groups), were investigated by NMR spectroscopy. The critical micellar concentration (CMC), the size, and shape of the aggregates were determined by diffusion ordered NMR spectroscopy (DOSY), while 2D NOESY NMR spectra were used to study the mutual spatial arrangement of surfactant molecules in the aggregated state. A nonlinear increase of the micellar hydrodynamic radius, indicating possible sphere-to-rod shape transition, was found for SDP2S at higher surfactant concentrations. Triton X-100 micelles were found to be almost spherical at low surfactant concentrations, but formation of ellipsoid shaped particles and/or micellar aggregation was observed at higher concentrations. The NOESY data show that at low concentration Triton X-100 forms a two-layer spherical structure in the micelles, with partially overlapping internal and external layers of Triton X-100 molecules and no distinct hydrophilic-hydrophobic boundary.     

Molecular orientation of monododecyl pentaethylene glycol at water/air and water/oil interfaces. A molecular dynamics computer simulation study

With a molecular dynamics computer simulation we investigated the dynamic properties of a monododecyl pentaethylene glycol (C₁₂E₅) molecule adsorbed at air/water and oil/water interfaces. In these simulations we investigated the molecular orientation of the surfactant molecules in detail. At the air/water interface the maximum of the C₁₂ chain tilt angle distribution measured with respect to the water surface is about 50°. This result is in fairly good agreement with neutron reflection experiments of monododecyl glycol ethers at the air/water interface. At the oil/water interface no significant changes were detected in the molecular orientation. We found that at equilibrium oil molecules penetrate into the hydrophobic monododecyl layer, this was also found by neutron reflection studies of the interactions between C₁₂E₅ and dodecane. The observed oil penetration results in an increase in the surface area per surfactant molecule. Received: 16 July 1999/Accepted in revised form: 28 August 1999