Polymerization of methyl methacrylate using isatoic anhydride–bromine donor–acceptor complex as the photoinitiator

Isatoic anhydride (IA) alone did not initiate photopolymerization of methyl metacrylate (MMA) at 40°C when exposed to visible light for about 180 min. But IA, when used in combination with bromine (Br₂) as the initiator, initiated the photopolymerization of MMA readily under the same conditions. This behavior was explained by the formation of a donor-acceptor type of complex between IA and Br₂ in the presence of MMA. The polymerization was found to proceed via a free radical mechanism and the radical generation process was considered to follow an initial complexation reaction between the initiator components and monomer. The complex initiator showed nonideal kinetics for the present system (initiator exponent < 0.5) and was analyzed. The monomer exponents varied from 0.83 to 1.15 normally depending on the nature of solvent used. Initiator-dependent chain termination was significant as well as the bimolecular mode of chain termination. © 1993 John Wiley & Sons, Inc.     

Photopolymerization of Methyl Methacrylate Using the Benzil-Dimethylaniline Combination as the Photoinitiator

Benzil (BZL)-dimethylaniline (DMA) exciplex interaction has been utilized to initiate the photopolymerization of methyl methacrylate at 40°C in bulk and in solution. Depending on the nature of the solvent used, the monomer exponent values varied between 0.47 to 2.76. Initiator exponent values were found to be 0.29 and 0.15 with respect to [BZL] and [DMA], respectively. A low value of k_p ²/k_t and the high initiator transfer constant values indicated significant initiator-dependent termination. The semipinacol radical formed during irradiation is thought to be mainly responsible for primary radical termination while the generated ion radicals are presumed to participate in degradative initiator transfer.     

Kinetic Investigation on the Photopolymerization of Methyl Methacrylate Using Iodine Trichloride as Initiator

The photopolymerization of MMA in visible light was studied at 45°C using IC1₃ as the photoinitiator. The initiator exponent was found to be 0.16 and the monomer exponent varied between 1.0 to 1.50, depending on the nature of the solvent. Analysis of the data revealed that the polymerization was induced by a free radical mechanism. Nonideality of the kinetics was explained on the basis of 1) Monomer-dependent chain initiation and 2) Initiator-dependent chain termination via degradative initiator transfer.     

Photopolymerization of methyl methacrylate using a combination of rhodamine 6G and benzoyl peroxide as photoinitiator in nonaqueous media

Photopolymerization of methyl methacrylate (MMA) in visible light was studied at 40°C using Rhodamine 6G—Benzoyl peroxide combination as photoinitiator. The photopolymerization proceeds by a free radical mechanism and the radical generation process occurs by an initial complexation reaction between the initiator components. Kinetic data indicated a lower-order dependence of R_p on initiator concentrations (initiator exponent < 0.5). Initiator-dependent chain termination was significant along with the bimolecular mode of chain termination.     

Comparative studies of the effects of dimethylaniline,methylaniline and aniline in the benzophenonesensitized photopolymerization of methyl methacrylate in bulk and in solution

Comparative studies of the photopolymerization of methyl methacrylate (MMA) at 35 using benzophenone (BP) as sensitizer in combination with dimethylaniline (DMA), methylaniline (MA) or aniline (A) are reported. In each case the initiator exponent is appreciably less than 0.5. Considering rates of polymerization, inhibition periods and apparent activation energy, the relative effectiveness of the amines in photopolymerization is DMA > MA > A. Solvent effects are also different in the 3 amine systems. In each case photoreduction of BP by the amine, through formation of the BP'-amine exciplex, leads to generation of an amine radical and the semipinacol radical, the former acting as an initiator and the latter as a terminator (primary radical termination). Kinetic analysis indicates that the rate constants of initiation, k_c for the amine radicals lie in the order DMA radical > MA radical > A radical.     

Photopolymerization of methyl methacrylate using tetrahydrofuran sulphur dioxide complex as photoinitiator

Photopolymerization of MMA in visible light was studied at 40 using THF-SO₂ complex as the photoinitiator. Initiator exponent was 0.19 and monomer exponent lay between 1.0 and 1.5, depending on thenature of solvent. Analysis of kinetic and other data indicate that the polymerization proceeds by a radical mechanism and termination is initiator dependent. Chain termination via degradative chain (initiator) transfer appears to be significant feature.     

Photopolymerization of methyl methacrylate with the use of iodine monobromide as photoinitiator

Iodine monobromide easily induces photopolymerization of methyl methacrylate (MMA) at 40°C under visible light. Initiator exponent and monomer exponent values were found to be 0.5 and 2, respectively, at low initiator concentrations, while the corresponding values at high initiator concentration conditions were zero and 3. The chain transfer constant of IBr at 40°C was found to be 13.0. Kinetic and other data indicate a radical polymerization mechanism involving complexation of monomer molecules with iodine monobromide prior to radical generation, and termination is believed to take place biomolecularly at low IBr concentrations and unimolecularly, involving reaction with the initiator, at high IBr concentrations (initiator termination).     

Photopolymerization of methyl methacrylate with the use of morpholine-chlorine charge transfer complex as the photoinitiator

Polymerization of methyl methacrylate (MMA) was kinetically studied under photo condition using near UV visible light at 40°C and employing morpholine (MOR)–chlorine (Cl₂) charge transfer (C-T) complex as the photoinitiator. The rate of polymerization (R_p) was dependent on morpholine/chlorine mole ratio; the 1 : 2 (MOR–Cl₂) C-T complex acted as the latent initiator complex, C, which underwent further complexation with the monomer molecules to give the actual initiator complex, I. Using 1 : 2 (MOR-Cl₂) C-T complex as the latent initiator, the initiator exponent evaluated for bulk photopolymerization of MMA was 0.071 and monomer exponent determined from studies of photopolymerization in benzene diluted system was 1.10. Benzoquinone behaved as a strong inhibitor and the polymers tested positive for the incorporation of chlorine atom end groups. Polymerization followed a radical mechanism. Kinetic nonideality as revealed by low (≪0.5) initiator exponent and a monomer exponent of greater than unity were explained in terms of primary radical termination effect. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1681–1687, 1997     

Photopolymerization of methyl methacrylate using benzophenone-dimethylaniline combination as photoinitiator

Photopolymerization of MMA at 35° was studied using benzophenone (BP)-dimethylaniline (DMA) combination as photo-redox initiator. Initiator exponent was 0.13; monomer exponent was < 1.0 in chlorinated solvents and > 1.0 in other solvents. Photoreduction of BP by DMA is considered to produce chain-initiating radicals and analysis of kinetic data indicates this process to be solvent and monomer dependent. Chlorinated solvents are indicated to be much more reactive than other solvents. The photopolymerization is also characterized by significant primary radical termination.     

Studies on Photopolymerization of Methyl Methacrylate Using Sulfur Dioxide-Halogen Combinations as Initiators

Free radical photopolymerization of methyl methacrylate (MMA) in visible light was studied at 40°C using sulfur dioxide-halogen (Cl₂, Br₂, and I₂) combinations as photoinitiators. Of the three SO₂/halogen systems, only the SO₂/Br₂ combination formed an interesting initiating system due to 1:1 complexation between the two components resulting in pronounced enhancement of the rate of photopolymerization over those produced by each of the initiator components when used as a lone photoinitiator. Photopolymerization of MMA induced by (SO₂-Br₂) complex (1:1) as the photoinitiator exhibited a low initiator exponent value, 0.26, and a monomer exponent value of 1.5. Kinetic nonidealities were explained on the basis of (a) monomer-dependent chain initiation and (b) significant initiator-dependent chain termination along with the usual bimolecular mode of chain termination.     

Polymerization of Methyl Methacrylate Using Acridone-Bromine Combination as the Photoinitiator

The photopolymerization of methyl methacrylate (MMA) in visible light was studied at 40°C using the acridone-bromine (acridone-Br₂) combination as the photoinitiator. The polymerization was found to proceed via a free radical mechanism, and the radical generation process was considered to follow an initial complexation reaction between monomer and each initiator component (acridone and Br₂), followed by further interaction between these two initiator-monomer complexes. Kinetic data indicated a lower-order dependence of R on initiator concentrations (initiator exponent < 0.5). Initiator-dependent chain termination was signifi-cant along with the usual bimolecular mode of chain termination. The monomer exponent varied from about 1.00 to 2.00, depending on the nature of solvents used. The nonidealities in this system were also analyzed.     

Photopolymerization of methylmethacrylate using triethylamine-benzoylperoxide redox initiator system

Photopolymerization of MMA was studied kinetically at 35° using TEA-BZ₂O₂ redox system as initiator. The initiator exponent is 0.34 but the monomer exponent depends on the solvent. Solvents (acetonitrile, pyridine and bromobenzene) giving negative or fractional monomer exponent show a rate enhancing effect through actively influencing the initiation step; benzene and chloroform give first order dependence of rate on [monomer] and behave as normal (inert) diluents. Initiation of polymerization takes place through radicals generated by photodecomposition of TEA-BZ₂O₂ complex formed in situ, the radical generation step being solvent or monomer dependent. Kinetic non-idealities are interpreted in terms of significant initiator dependent termination via degradative chain transfer.     

Photopolymerization of methyl methacrylate with the use of tetrahydrofuran–bromine charge-transfer complex as the photoinitiator

The polymerization of MMA was kinetically studied in the presence of visible light (using a 125-W high-pressure mercury vapor lamp with fluorescent coating, without a filter), a THF—bromine charge-transfer complex being used as the photoinitiator. The initiator exponent was 0.5 in bulk polymerization. The monomer exponent varied from about 1.2 to about 2.5, depending on the nature of the solvent used; the initiator exponent also varied in diluted systems, depending on the nature and proportion of the solvent, the variation being from a value of 0.5 in bulk system to zero or almost zero at about 25% (v/v) solvent concentration. Other kinetic parameters, viz., k_p²/k_t and the activation energy for polymerization, were determined and are reported. Kinetic and other evidence indicates that the photopolymerization takes place by a radical mechanism and termination is bimolecular in nature in bulk systems; in dilute systems, termination by initiator complex assumes predominance, particularly at high solvent concentrations (≥25% v/v).     

Photopolymerization of methyl methacrylate with the use of iodine as the photoinitiator

Kinetics of photopolymerization of MMA at 40°C with the use of iodine as the photoinitiator was studied. At low range of iodine concentration (< 0.0004M), the rate of polymerization was proportional to square root of iodine concentration and the monomer exponent was 2.5, while at a higher range of iodine concentration, (0.0005–0.002M) the initiator exponent and monomer exponent were zero and 3.6–3.8 (i.e., close to 4), respectively. The chain-transfer constant of iodine at 40°C was found to be 6.0. Polymerization was found to be largely inhibited in the presence of relatively high concentrations of iodine (> 0.005M) and also in presence of hydroquinone. Kinetic and other data indicate a radical mechanism of polymerization involving complexation of monomer molecules with iodine prior to radical generation, and termination is believed to take place bimolecularly at low iodine concentrations and unimolecularly, involving reaction with iodine, at high iodine concentrations (initiator termination).     

Studies on vinyl photopolymerization using a macromolecular C.T. Complex between poly(N-vinyl carbazole) and bromine as the photoinitiator

Photopolymerization of methyl methacrylate (MMA) was studied at 40°C using a macromolecular C.T. Complex between poly(N-vinyl carbazole) and bromine, expressed in brief as (PNVC–Br₂) complex, as the photoinitiator. Initiator exponent was 0.40 for [PNVC–Br₂] ≤ 2.5 × 10^?3 mol L^?1 and practically zero for [PNVC–Br₂] > 2.5 × 10^?3 mol L^?1. Monomer exponent in different diluent systems such as benzene, carbon tetrachloride, and acetone was close to 1.0. Low initiator exponent (<0.5) is explained on the basis of an initiator-dependent termination mechanism, in addition to the usual bimolecular termination. Analysis of kinetic data indicates that the initiator-dependent termination is primarily due to degradative initiator transfer and that due to primary radicals is considered inconsequential in view of monomer exponent being close to unity. The non-ideal termination process assumes over-whelming prominence at high [PNVC–Br₂].     

Photopolymerization of methyl methacrylate and some other vinyl monomers with the use of chlorine as photoinitiator

Low concentrations (0.001–0.03M) of chlorine easily induce photopolymerization of MMA at 40°C. Kinetic data indicate that polymerization follows a radical mechanism involving complexation of monomer by the initiator and initiation takes place through radical generation during photodecomposition of the initiator-monomer complex. Termination appears to take place bimolecularly. The k_p²/k_t value for MMA polymerization at 40°C was found to be 0.83 × 10^?2. Rates of chlorine-initiated photopolymerization were found to decrease in the order MMA, EMA ? VA, Sty > MA.     

Novel solvent effects in the photopolymerization of methyl methacrylate by use of quinoline–bromine charge-transfer complex as photoinitiator

Photopolymerization of MMA was carried out at 40°C in diluted systems by use of quinolinebromine (Q–Br₂) charge-transfer complex as the initiator and chloroform, carbon tetrachloride, chlorobenzene, dioxane, THF, acetone, benzene, toluene, quinoline, and pyridine as solvents. The results showed variable monomer exponents ranging from 1 to 3. For chloroform, carbon tetrachloride, and chlorobenzene, the monomer exponent observed was unity; for other solvents used, the value of the same exponent was much higher (between 2 and 3). Initiation of polymerization is considered to take place through radicals generated in the polymerization systems by the photodecomposition of (Q–Br₂)–monomer complex (C) formed instantaneously in situ on addition of the Q–Br₂ complex in monomer. The kinetic feature of high monomer exponent is considered to be due to higher order of stabilization of the initiating complex (C) in presence of the respective solvents. In the presence of the retarding solvents, very low or zero initiator exponents were also observed, depending on the nature and concentration of the solvents used. The deviation from the square-root dependence of rate on initiator concentration becomes higher at high solvent and initiator concentrations in general. This novel deviation is explained on the basis of initiator termination, probably via degradative chain transfer involving the solvent-modified initiating complexes and the propagating radicals.     

Use of an Internal Keto-Imino Compound as the Photoinitiator in the Polymerization of Methyl Methacrylate

Photopolymerization of MMA in visible light was studied at 40°C using acridone as the photoinitiator. The polymerization was found to proceed via a free radical mechanism and the radical generation process was considered to follow an initial complexation reaction between monomer and acridone. Kinetic data indicated a lower order dependence of R_p on the initiator concentration (initiator exponent < 0.5). Initiator-dependent chain termination was significant along with the usual bimolecular mode of chain termination. The monomer exponent varied from about 1.0 to 1.5, depending on the nature of the solvent used. The nonidealities in this case were also analyzed.     

Aqueous Polymerization of Methyl Methacrylate Initiated by Potassium Pervanadate

The aqueous polymerization of methyl methacrylate was kinetically studied using acidic (H₂SO₄) potassium pervanadate as initiator. The initiator exponent was 0.3 and the monomer exponent was 1.0. Polymerization is considered to proceed by a radical mechanism, and termination takes place quite measurably by a degradative initiator transfer mechanism.     

Photopolymerization of methyl methacrylate using hydrogen peroxide as the photoinitiator

Photopolymerization of MMA with the use of H₂O₂ as the photoinitiator under visible light at 30°C was studied. Kinetic features in bulk monomer and in the presence of different diluents differ significantly. Usual free radical kinetics with square-root dependence of rate on initiator, indicating bimolecular termination of chain radicals, were observed for bulk polymerization. On dilution with various solvents polymerization was found to be retarded to different (usual and more than usual) extents, the observed monomer exponent value being much higher than unity in many cases. This deviation from normal kinetics has been interpreted in terms of the predominance of degradative initiator transfer in the diluted systems.