邻羧基苯基荧光酮与碲显色反应的研究及应用

在ｐＨ＝４．５ＨＡｃ－ＮａＡｃ缓冲介质中,ＣＴＭＡＢ存在下,邻羧基苯基荧光酮（ｏ－ＣＰＦ）和Ｔｅ（Ⅳ）生成４∶１稳定络合物,λｍａｘ＝５６０ｎｍ,ε＝１．２５×１０５Ｌ·ｍｏｌ－１·ｃｍ－１。Ｔｅ（Ⅳ）含量在０—１０μｇ／２５ｍＬ内符合比耳定律,方法用于烟尘中碲的测定,结果令人满意。     

桂利嗪的荷移分光光度法测定

本研究了桂利嗪与７．７,８,８－四氰基对二次甲苯醌（ＴＣＮＱ）的荷移（ＣＴ）反应,确定了荷移反应的最佳条件。结果表明：在丙酮－甲醇介质中,二于室温条件下１０ｍｉｎ即可形成１：１的络合物,在其最大吸收波长７４３ｎｍ处表观摩尔吸光系数ε＝１．５８×１０＾４Ｌ·ｍｏｌ＾－１·ｃｍ＾－１,在０～１８μｇ·ｍＬ＾－１范围内符合比尔定律。方法的相对标准偏差小于３％（ｎ＝１０）。对形成ＣＴ络合物的机理进行了     

铂(Ⅳ)-钼酸盐-乙基罗丹明B离子缔合显色反应研究

本文研究了在聚乙烯醇（ＰＶＡ）存在下用钼酸盐与乙基罗丹明Ｂ（ＥＲＢ）形成离子缔合物，该缔合物的最大吸收位于５８０ｎｍ，摩尔吸光系数为１．１２×１０６Ｌ·ｍｏｌ－１·ｃｍ－１，服从比耳定律范围０—２．５μｇ／２５ｍＬ，缔合物至少稳定１周，考察了５０多种共存离子的影响，除生成杂多酸元素和Ａｕ（Ⅲ）、Ｏｓ（Ⅷ）、Ｐｄ（Ⅱ）、Ｉｒ（Ⅳ）外，大多数元素不干扰。测定铂的条件为：〔ＨＣｌＯ４〕＝１．２ｍｏｌ／Ｌ，〔ＭｏＯ４２－〕＝９．１×１０－４ｍｏｌ／Ｌ，〔ＥＲＢ〕＝３．２×１０－５ｍｏｌ／Ｌ，０．０８％ＰＶＡ。缔合物的摩尔比为Ｐｔ（Ⅳ）∶ＥＲＢ＝１∶２，本法已用于铂矿中铂的测定，结果满意。     

I-3-淀粉体系间接测定水中痕量锰

本文提出了Ｉ３＾－淀粉体系测定痕量锰的方法。本法灵敏度高,ε＝１．１２×１０＾５Ｌ·ｍｏｌ＾－１·ｃｍ＾－１,选择性好。除Ｆｅ＾３Ｍ其他元素几乎无干扰,实测了天然水中锰,结果令人满意。     

P538萃取锰（Ⅱ）的研究

在２５±０．５℃，用Ｐ５３８的环己烷溶液从ＮａＣｌＯ４－ＨＣｌＯ４介质中萃取Ｍｎ（Ⅱ）的反应机理为离子交换机理，萃取焓△Ｈ＝－１９６ｋＪ．ｍｏｌ＾－１并用Ｃｌ＾－离子水合作用和Ｍｎ＾２＋与Ｃｌ＾－形成配合物的竞争解释了萃取分配比与水相中ＮａＣｌ浓度的关系。     

新试剂1-(2-羟基苯基)-3-[4-(苯基偶氮)苯基]-三氮烯的合成及与溴化十六烷基三甲铵的显色反应

合成了新试剂１－（２－羟基苯基）－３－［４－（苯基偶氮）苯基］－三氮烯（ＨＰＡＰＴ）,在氢氧化钠碱性介质中,该试剂与溴化十六烷基三甲铵（ＣＴＭＡＢ）形成１∶３的紫红色离子缔合物。λｍａｘ位于５６５ｎｍ,表观摩尔吸光系数为１．５９×１０４Ｌ·ｍｏｌ－１·ｃｍ－１,ＣＴＭＡＢ含量在３—２９．１６ｍｇ·Ｌ－１范围内符合比耳定律。测定了显色体系ＣＴＭＡＢ的临界胶束浓度是１．５０×１０－４ｍｏｌ·Ｌ－１。     

六亚甲基桥连的希夫碱及其锰（Ⅲ）络合物催化剂的红外光谱研究

研究了六亚甲基桥连的希夫碱及其锰（Ⅲ）络合物催化剂的红外光谱，对一些主要谱带进行了经验归属。配体的分子内氢键谱带出现在～３４３８ｃｍ－１（以ＬＨ为例），νＣ＝Ｎ谱带在～１６３０ｃｍ－１（以ＣＨ为例，下同），苯的特征谱带在～１５９８，～１４６９和～７５５ｃｍ－１，νＭｎ—Ｎ为主的复合振动在～３６９ｃｍ－１，δＭｎ—Ｎ为主的复合振动在～２４７ｃｍ－１，νＭｎ—Ｏ为主的复合振动在～３２９ｃｍ－１，δＭｎ—Ｏ为主的复合振动在～２７５ｃｍ－１，νＭｎ—Ｃｌ特征谱带在～３０３ｃｍ－１。与苯基锰（Ⅲ）卟啉络合物相比，νＭｎ—Ｎ特征谱带向高波数位移，νＭｎ—Ｃｌ特征谱带则向低波数有较大位移。     

新试剂2-(4-安替比林偶氮)-5-二乙氨基苯胺与钯显色反应的研究及应用

在ｐＨ＝５．０ＨＡｃ－ＮａＡｃ缓冲介质中,吐温－８０存在下,２－（４－安替比林偶氮）－５－二乙氨基苯胺（ＡＤＥＡ）与钯生成２∶１红色络合物,λｍａｘ＝５３０ｎｍ,ε＝６．１５×１０４Ｌ·ｍｏｌ－１·ｃｍ－１,钯的含量在０—２０μｇ／２５ｍＬ内符合比耳定律,本方法用于钯催化剂中痕量钯的测定,结果令人满意。     

分光光度法测定烟叶中镁的研究

在ｐＨ＝ ７．０ ＮＨ４Ａｃ 缓冲介质中,苦氨酸偶氮－Ｈ－酸（ＰＨＡ）与镁反应生成２∶１ 蓝紫色络合物,λｍ ａｘ＝６３０ｎｍ ,ε＝ １．１６×１０４Ｌ·ｍ ｏｌ－ １·ｃｍ － １,镁的含量在０．５－ ４０μｇ／２５ｍ Ｌ内符合比尔定律,本方法用于烟草样品中镁的测定,结果令人满意。     

分光光法测定烟叶中钙的研究

在弱碱性介质中,乳化剂－ＯＰ存在下,羟基萘酚蓝（ＨＮＢ）和钙生成蓝色２∶１ 络合物,λｍａｘ＝ ６５０ｎｍ ,ε＝ １．８６×１０４Ｌ·ｍ ｏｌ－ １·ｃｍ － １,钙含量在０－ ４０μｇ／２５ｍ Ｌ内符合比尔定律,本方法用于烟叶中钙的测定,结果令人满意。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.