Indirect flow-injection spectrophotometric determination of meloxicam, tenoxicam and piroxicam in pharmaceutical formulations.

A simple and sensitive indirect spectrophotometric method for the assay of meloxicam (MX), tenoxicam (TX) and piroxicam (PX) in pure and in pharmaceutical formulations by flow injection analysis (FIA) has been proposed. The method is based on the oxidation of these drugs by a known excess of N-bromosuccinimide (NBS) in an acidic medium, followed by a reaction of excess oxidant with chloranilic acid (CAA) to bleach its purple color. The absorbance values increased linearly with increasing concentrations of the drugs. Variables, such as the acidity, reagent concentrations, flow rate of reagents and other FI parameters were optimized to produce the most sensitive and reproducible results. The system obeyed Beer's low over concentration ranges of 10 - 160, 20 - 200 and 10 - 160 microg/ml for MX, TX and PX, respectively. The common excipients and additives did not interfere with their determinations. The method was successfully applied to the determinations of MX, TX and PX in various pharmaceutical preparations. The results obtained by the proposed method were found to be in good agreement with those found by the official HPLC methods.     

Highly sensitive and selective spectrophotometric and spectrofluorimetric methods for the determination of ropinirole hydrochloride in tablets

Three sensitive, selective, accurate spectrophotometric and spectrofluorimetric methods have been developed for the determination of ropinirole hydrochloride in tablets. The first method was based on measuring the absorbance of drug solution in methanol at 250 nm. The Beer's law was obeyed in the concentration range 2.5-24 microg ml(-1). The second method was based on the charge transfer reaction of drug, as n-electron donor with 7,7,8,8-tetracyanoquinodimethane (TCNQ), as pi-acceptor in acetonitrile to give radical anions that are measured at 842 nm. The Beer's law was obeyed in the concentration range 0.6-8 microg ml(-1). The third method was based on derivatization reaction with 4-chloro-7-nitrobenzofurazan (NBD-Cl) in borate buffer of pH 8.5 followed by measuring the fluorescence intensity at 525 nm with excitation at 464 nm in chloroform. Beer's law was obeyed in the concentration range 0.01-1.3 microg ml(-1). The derivatization reaction product of drug with NBD-Cl was characterized by IR, 1H NMR and mass spectroscopy. The developed methods were validated. The following analytical parameters were investigated: the molar absorptivity (epsilon), limit of detection (LOD, microg ml(-1)) and limit of quantitation (LOQ, microg ml(-1)), precision, accuracy, recovery, and Sandell's sensitivity. Selectivity was validated by subjecting stock solution of ropinirole to acidic, basic, oxidative, and thermal degradation. No interference was observed from common excipients present in formulations. The proposed methods were successfully applied for determination of drug in tablets. The results of these proposed methods were compared with each other statistically.     

Indirect spectrophotometric determination of propranolol hydrochloride and piroxicam in pure and pharmaceutical formulations.

Two simple and sensitive indirect spectrophotometric methods for the assay of propranolol hydrochloride (PPH) and piroxicam (PX) in pure and pharmaceutical formulations have been proposed. The methods are based on the oxidation of PPH by a known excess of standard N-bromosuccinimide (NBS) and PX by ceric ammonium sulfate (CAS) in an acidic medium followed by the reaction of excess oxidant with promethazine hydrochloride (PMH) and methdilazine hydrochloride (MDH) to yield red-colored products. The absorbance values decreased linearly with increasing concentration of the drugs. The systems obeyed Beer's law over the concentration ranges of 0.5 - 12.5 and 0.3 - 16.0 microg/ml for PPH, and 0.4 - 7.5 and 0.2 - 10 microg/ml for PX with PMH and MDH, respectively. Molar absorptivity values, as calculated from Beer's law data, were found to be 1.36 x 10(4) and 2.55 x 10(4) l mol(-1) cm(-1) for PPH, and 2.08 x 10(4) and 2.05 x 10(4) l mol(-1) cm(-1) for PX with PMH and MDH, respectively. The common excipients and additives did not interfere with their determinations. The proposed methods have been successfully applied to the determinations of PPH and PX in various dosage forms. The results obtained by the proposed methods compare favorably with those of official methods.     

A selective spectrophotometric method for determination of rosoxacin antibiotic using sodium nitroprusside as a chromogenic reagent

A selective spectrophotometric method for the determination of rosoxacin (ROS), a 4-quinolone antimicrobial agent, has been developed and validated. The method was based on the reaction of ROS with alkaline sodium nitroprusside (SNP) reagent at room temperature forming a red colored chromogen measured at 455 nm. The conditions affecting the reaction (SNP concentration, pH, color-developing time, temperature, diluting solvent and chromogen stability time) were optimized. Under the optimum conditions, good linear relationship (r=0.9987) was obtained between the absorbance and the concentration of ROS in the range of 20-50 microg ml(-1). The assay limits of detection and quantitation were 2.5 and 8.4 microg ml(-1), respectively. The method was successfully applied to the analysis of bulk drug and laboratory-prepared tablets; the mean percentage recoveries were 100.1+/-0.33 and 101.24+/-1.28%, respectively. The results were compared favourably with those obtained by the reported method; no significant difference in the accuracy and precision as revealed by the accepted values of t- and F-tests, respectively. The robustness and ruggedness of the method was checked and satisfactory results were obtained. The proposed method was found to be highly selective for ROS among the fluoroquinolone antibiotics. The reaction mechanism was proposed and it proceeded in two steps; the formation of nitroferrocyanide by the action of sodium hydroxide alkalinity on SNP and the subsequent formation of the colored nitrosyl-ROS derivative by the attack at position 6 of ROS.     

Spectrophotometric determination of benzydamine HCl, levamisole HCl and mebeverine HCl through ion-pair complex formation with methyl orange

A simple, rapid and sensitive spectrophotometric method has been proposed for the assay of benzydamine HCl (BENZ), levamisole HCl (LEV) and mebeverine HCl (MBV) in bulk and pharmaceutical formulations. The method based on the reaction of the selected drugs with methyl orange (MO) in buffered aqueous solution at pH 3.6. The formed yellow ion-pair complexes were extracted with dichloromethane and measured quantitatively with maximum absorption at 422 nm. The analytical parameters and their effects on the reported systems are investigated. The extracts are intensely colored and very stable at room temperature. The calibration graphs were linear over the concentration range of 2-10 microg ml(-1) for BENZ, 6-24 microg ml(-1) for LEV and 4-14 microg ml(-1) for MBV. The stoichiometry of the reaction was found to be 1:1 in all cases and the conditional stability constant (K(f)) of the complexes have been calculated. The proposed method was successfully extended to pharmaceutical preparations-tablets. Excipients used as additive in commercial formulations did not interfere in the analysis. The proposed method can be recommended for quality control and routine analysis where time, cost effectiveness and high specificity of analytical technique are of great importance.     

Determination of copper and zinc in serum by derivative atomic absorption spectrometry using the microsampling technique

A method has been developed for the determination of copper and zinc in the serum of rats by derivative microsampling flame atomic absorption spectrometry (D-MFAAS). The microsampling volume, solution uptake rate and other figures of merit of the proposed methodology were studied. For a 100 microl volume, the characteristic concentrations and detection limits (3s) of D-MFAAS were 0.023 and 0.013 microg ml(-1) for copper and 0.0066 and 0.0080 microg ml(-1) for zinc, which were 4.5-6.5-fold better than those of microsampling flame atomic absorption spectrometry (MFAAS). The detection limits and sensitivities of D-MFAAS were 6.4- and 16-fold for 300 microl volume for copper, 14- and 13-fold for 250 microl volume for zinc, better than those of MFAAS. The method demonstrates high tolerance to interferences, and the analytical results obtained for a certified reference material, GBW 08551 Pork Liver, were in good agreement with the certified values. The recovery with the standard additions method was good, in the range 97.6-101.5%, and precisions (relative standard deviations) obtained for a diluent sample containing 0.5 microg ml(-1) copper and 0.7 microg ml(-1) zinc were 4.0% and 3.5% (n = 15) for copper and zinc, respectively.     

Spectrophotometric determination of periodate, iodate and bromate mixtures based on their reaction with iodide.

A rapid, simple, precise and accurate method is proposed for the determination of ternary mixtures of periodate-iodate-bromate based on their reaction with iodide ion at different pH values. The absorbance was measured at 352 nm. Three sets of reaction conditions were developed. In the first set of conditions, only periodate reacted with iodide, but in the second set the periodate and iodate reacted with iodide and in the third set the three ions reacted with iodide during the first 3 min after initiation of the reaction. The method could be used for individual determinations of periodate, iodate and bromate in the concentration range of 0.05-8.0 microg/ml, 0.05-5.0 microg/ml and 0.2-12 microg/ml, respectively. The data were evaluated by simultaneous equations.     

A simple and rapid spectrophotometric determination of thallium(III) with trifluoperazine hydrochloride.

A simple, sensitive and rapid spectrophotometric method was developed for the determination of thallium(III) using trifluoperazine hydrochloride (TFPH). The method is based on the oxidation of TFPH by thallium(III) in a phosphoric acid medium to form a red-colored radical cation with an absorption maximum at 505 nm. Beer's law is valid over the concentration range of 0.5 - 6.5 microg ml(-1) of thallium(III). The molar absorptivity and Sandell's sensitivity of the color system are 2.14 x 10(4) l mol(-1) cm(-1) and 0.0095 microg cm(-2), respectively. The optimum reaction conditions and other analytical parameters were evaluated. The tolerance limit of the method towards various ions usually associated with thallium has been studied. The proposed method has been successfully applied to the analysis of thallium in alloys, minerals, standard reference material, water, and urine samples.     

Spectrophotometric methods for the determination of nifurtimox in bulk form and pharmaceutical formulations

Three simple and sensitive methods for the assay of Nifurtimox (NIF) which is an active antitrypanocide were developed. These methods are based on the formation of coloured species by treating either its reduction product with 3-methyl-2-benzothiazolinone hydrazone (MBTH) in the presence of ferric chloride (method A) or its hydrolysis product with 2-thiobarbituric acid (TBA) (method B) or by oxidizing it with excess N-bromosuccinamide (NBS) and determining the consumed NBS using p-N-methylaminophenol sulphate (metol)-isonicotinic acid hydrazide (INH) (method C). All variables have been optimized and the reaction mechanisms presented. Regression analysis of Beer's plot showed good correlation in the concentration range of 2.5-10, 2.5-30 and 1.25-7.5 microg/ml for methods A, B and C, respectively. No interference was observed from the additives and the validity of the methods was tested by analysing the tablets. Recoveries were 99.2-100.9%.     

Highly selective spectrophotometric flow-injection determination of trace amounts of bromide by catalytic effect on the oxidation of m-cresolsulfonephthalein by periodate

A new flow-injection method is reported for the determination of bromide. The method is based on catalytic effect of bromide on the oxidation of m-cresolsulfonephthalein by periodate in acidic media. The reaction was followed spectrophotometrically by measuring the decrease in absorbance at 528 nm. The influence of pH, reagent concentration and manifold variables on the sensitivity was studied. Under optimum conditions, a calibration graph was obtained in the range of 0.160-20.00 microg ml(-1) bromides with a limit of detection of 0.150 microg ml(-1) bromide. The relative standard deviation for ten replicate measurement of 1.0 microg ml(-1) bromide was 2.1%. The influence of potential interfering ions on the selectivity was studied. The method successes to measure bromide in the presence of other halide ions. The method was used to measure bromide in river water and tap water.     

Univariate and simplex optimization for the flow-injection spectrophotometric determination of copper using nitroso-R salt as a complexing agent.

A simple colorimetric flow-injection system for the determination of Cu(II) based on a complexation reaction with nitroso-R salt is described. The chemical and FIA variables were established using the univariate and simplex methods. A small volume of Cu(II) was mixed with merged streams of nitroso-R salt and acetate buffer solutions. The absorbance of the complex was continuously monitored at 492 nm. The calibration curve over the concentration range 1.0-7.0 microg ml(-1) was obtained. The relative standard deviation for determining 4.0 microg ml(-1) Cu(II) was 0.47% (n = 11). The detection limit (3sigma) was 0.68 microg ml(-1) and the sample throughput was 150 h(-1). The validity of the method has been satisfactorily examined for the determination of Cu(II) in wastewater and copper ore samples. The accuracy was found to be high, because the student t-values were calculated to be less than the theoretical values when the results were compared with those obtained by FAAS.     

Utility of oxidation-reduction reaction for the determination of ranitidine hydrochloride in pure form,in dosage forms and in the presence of its oxidative degradates

Three simple, accurate and sensitive colorimetric methods (A, B and C) for the determination of ranitidine HCl (RHCl) in bulk sample, in dosage forms and in the presence of its oxidative degradates are described. The first method A is based on the oxidation of the drug by N-bromosuccinimide (NBS) and determination of the unreacted NBS by measurement of the decrease in absorbance of amaranth dye (AM) at a suitable lambda(max)=520 nm. The methods B and C involve the addition of excess Ce(4+) and determination of the unreacted oxidant by decrease the red color of chromotrope 2R (C2R) at a suitable lambda(max)=528 nm for method B or decrease the orange pink color of rhodamine 6G (Rh6G) at a suitable lambda(max)=526 nm for method C. Regression analysis of Beer-Lambert plots showed good correlation in the concentration ranges 0.2-3.6, 0.1-2.8 and 0.1-2.6 microg ml(-1) for methods A, B and C, respectively. The apparent molar absorptivity. Sandell sensitivity, detection and quantitation limits were calculated. For more accurate results, Ringbom optimum concentration ranges were 0.3-3.4, 0.2-2.6 and 0.2-2.4 microg ml(-1) for methods A, B and C, respectively. Analyzing pure and dosage forms containing RHCl tested the validity of the proposed methods. The relative standard deviations were 相似文献   

PARAFAC and PLS applied to spectrophotometric determination of tetracycline in pharmaceutical formulation and biological fluids

A simple and rapid analytical procedure was proposed for determination of tetracycline in pharmaceutical formulation, urine and plasma based on chemometrics methods and spectrophotometric measurements. The calibration set was constructed with twenty solutions in concentration range 0.25-13.00 microg ml(-1) for tetracycline. The procedure was repeated at nine different pH values. Partial least squares (PLS) models were built at each pH and used to determinate a set of synthetic tetracycline solutions. The best model was obtained at pH 8.00 (PLS-PH8). Parallel factor analysis (PARAFAC) model was applied to a three-way array constructed using all the pH data sets and enabled better results. The capabilities of the method for the analysis of real samples were evaluated by determination of tetracycline in pharmaceutical formulations and biological fluids with satisfactory results.     

Spectrophotometric determination of urea in dermatologic formulations and cosmetics

A rapid, relatively sensitive, and low-cost method for the determination of water-soluble urea content in dermatological therapy products and cosmetics is proposed using a new spectrophotometric assay with water as the only extraction solvent. Spectrophotometric methods involve addition of a known excess of bromate to urea in an acid medium, followed by the determination of residual bromine and chlorine reacting with methyl orange and measurement of absorbance at 505 nm. The absorbance increases linearly with urea concentration (r = 0.9998). The systems obey Beer's law for 6 - 90 microg ml(-1). The calculated apparent molar absorbance values are found to be 4.537 x 10(3) dm(3) mol(-1) cm(-1) and the Sandell's sensitivity is 0.013 microg cm(-2). The variables affecting the rate of the reaction were investigated. The relative standard deviation for five-replication determination of 60 microg ml(-1) urea was 2.1% and the detection limit of the method is 0.34 ng ml(-1).     

Slurry sample introduction with fluorinating electrothermal vaporization for the direct ICP-AES determination of boron in plant leaves

Summary The slurry sample introduction with fluorinating electrothermal vaporization has been applied to ICP-AES for the determination of boron in plant leaves. The main working parameters for ETV-ICP-AES, such as r.f. power, gas flow rate, drying temperature and atomization temperature have been studied. The concentration of the fluorinating agent polytetrafluoro-ethylene was examined for the boron determination. The matrix concentrations of Na, K, Ca and Mg up to 5 mg/ml do not interfere with the fluorinating vaporization of boron. Several plant samples were analysed with the standard addition method. A good agreement of analytical results between this method and a spectrophotometric method was obtained. The determined value of boron in NBS SRM 1573 tomato leaves coincides with literature values.     

Spectrofluorimetric determination of drugs containing active methylene group using N1-methyl nicotinamide chloride as a fluorigenic agent

A spectrofluorimetric method was described for the determination of drugs containing active methylene groups adjacent to carbonyl groups. The method was applied successfully to the determination of three life saving cardiovascular drugs, with narrow therapeutic indices: pentoxifylline (I), propafenone hydrochloride (II) and acebutolol hydrochloride (III), in laboratory-prepared mixtures, in commercial tablets and in plasma samples. The method involved the reaction of each of the tested drugs with N1-methyl nicotinamide chloride (NMNCl) in the presence of alkali, followed by addition of formic acid, where highly fluorescent reaction products were produced. The produced fluorescence were measured quantitatively at 472 nm (lambdaex 352 nm), 409 nm (lambdaex 310 nm) and 451 nm (lambdaex 266 nm) for (I), (II), and (III) respectively. The method was linear over concentration ranges of 10-1000 microg/ml , 0.2-12 microg/ml and 0.08-10 microg/ml in standard solutions for (I), (II), and (III) respectively. In spiked human plasma samples, calibration graphs were linear over concentration ranges of 20-1000 microg/ml, 0.2-15 microg/ml and 0.08-10 microg/ml for (I), (II), and (III) respectively. The method showed good accuracy, specificity and precision in both laboratory-prepared mixtures and spiked human plasma samples. The proposed method is simple, with low instrumentation requirements, suitable for quality control application, bioavailability and bioequivalency studies.     

Spectrophotometric determination of some dibenzazepines with picryl chloride

A simple and sensitive spectrophotometric method has been developed for the determination of some dibenzazepines, based on reaction with picryl chloride in chloroform medium and measurement at 395 nm. Beer's law is obeyed in concentration ranges 0.1-1.0 microg/ml for imipramine hydrochloride, trimipramine maleate and opipramol dihydrochloride, 0.16-1.6 microg/ml for desipramine hydrochloride and 0.4-2.4 microg/ml for clomipramine hydrochloride. The method was applied successfully to the determination of dibenzazepines in tablets and the results were comparable to those obtained by official procedures.     

Spectrofluorimetric determination of acetaminophen with N-bromosuccinimide

A simple, sensitive, and selective method for determination of acetaminophen based on its oxidation using N-bromosuccinimide (NBS) to produce a highly fluorescent product. Optimization of reaction variables was carried out concerning NBS concentration, pH, temperature, reaction time, and stability time. Under optimal analytical conditions, the fluorescent intensity was measured at lambda emission. 442 nm (excitation at lambda 330 nm). The linearity range is 120-800 ng/mL with lower detection limit of 33.6 ng/mL acetaminophen. The method was applied successfully to the determination of the compound in pharmaceutical preparations, with average recovery of 100.3 +/- 2%. The method was also applied successfully to the determination of the drug in spiked plasma samples, with an average recovery of 101.2 +/- 1%. Interference effects of some compounds, present in combination with acetaminophen, were studied and the tolerance limits of these compounds were determined.     

Trace-level determination of triazines and several degradation products in environmental waters by disk solid-phase extraction and micellar electrokinetic chromatography

An analytical method combining disk solid-phase extraction with micellar electrokinetic chromatography has been developed for the determination of atrazine, simazine, hydroxyatrazine, deisopropylatrazine, deethylatrazine, propazine and prometryn in water samples. The influence of the buffer and sodium dodecyl sulfate (SDS) concentration, pH and organic modifier on the separation has been studied. Baseline separation of the seven triazines was achieved under the following conditions: 10 mM borate buffer, 60 mM SDS, 20% methanol and pH 9.2. C18-bonded silica and poly(styrene-divinylbenzene) (PS-DVB) disks were evaluated for solid-phase extraction of the selected pesticides (11 of water sample). Using two PS-DVB disks, quantitative recoveries were obtained for all pesticides tested. The method was successfully applied for the determination of the seven triazines in drinking and well water at the 0.1 microg l(-1) and 0.5 microg l(-1) concentration levels, respectively. The detection limits for these analytes using the proposed analytical method were within the 0.02-0.06 microg l(-1) range in drinking water and the 0.06-0.30 microg l(-1) range in well water.     

Native fluorescence flow-through optosensor for the fast determination of diphenhydramine in pharmaceuticals.

A single, rapid flow-through optosensor spectrofluorometric system is proposed for the determination of diphenhydramine in different pharmaceutical preparations. This sensor was developed in conjunction with a monochannel flow-injection analysis system with fluorometric solid-phase transduction. Diphenhydramine was directly injected into a carrier stream of ethanol/water, 50% (v:v), and transitorily retained on a sorption gel Sephadex G-15 placed in the detection area into the cell. The determination was carried out without any derivatization reaction by directly measuring the intrinsic fluorescence of the analyte and using the peak height as an analytical signal. The chemical and instrumental variables were optimized, and the influence of some foreign substances that can be found in typical pharmaceutical samples containing diphenhydramine was also investigated. Diphenhydramine could be determined in the concentration ranges of 0.5 - 8 microg ml(-1) and 0.1 - 1.2 microg ml(-1) with detection limits of 0.088 and 0.019 microg ml(-1) at sampling rates of 30 and 19 h(-1) for 200 and 800 microl of the sample volume, respectively.