Achievement of ultimate values of the bulk and shear strengths of iron irradiated by femtosecond laser pulses

Shock-wave phenomena generated by femtosecond laser pulses in submicron iron film samples have been studied by the interferometric method with the application of frequency-modulated diagnostics in the picosecond time range. The splitting of the shock wave into the elastic and plastic waves with a compression stress of up to 27.5 GPa behind the front of an elastic precursor has been detected. The corresponding maximum shear stress reaches 7.9 GPa, which is even somewhat higher than the calculated ideal shear strength. The measured spall strengths reach 20.3 GPa, which is also comparable to the calculated values of the ideal tensile strength.     

Behavior of aluminum near an ultimate theoretical strength in experiments with femtosecond laser pulses

The dynamics of the motion of the free surface of micron and submicron films under the action of a compression pulse excited in the process of femtosecond laser heating of the surface layer of a target has been investigated by femtosecond interferometric microscopy. The relation between the velocity of the shock wave and the particle velocity behind its front indicates the shock compression to 9–13 GPa is elastic in this duration range. This is also confirmed by the small (≤1 ps) time of an increase in the parameters in the shock wave. Shear stresses reached in this process are close to their estimated ultimate values for aluminum. The spall strength determined at a strain rate of 10⁹ s⁻¹ and a spall thickness of 250–300 nm is larger than half the ultimate strength of aluminum.     

Superelasticity and the propagation of shock waves in crystals

The separation of a shock wave into an elastic precursor and a plastic wave is a characteristic phenomenon occurring only in solid media. The existence of the elastic shock wave at pressures p ≈ 10 GPa, which is one or two orders of magnitude higher than the dynamic elastic limit, has been detected in recent numerical calculations and a femtosecond laser experiment. The plastic shock wave has no time to be formed in these ultrashort waves at p ≈ 10 GPa. The processes of the formation and propagation of the elastic and plastic waves in aluminum at higher pressures obtained by means of femtosecond lasers have been analyzed in this work. It has been found that the elastic precursor survives even under the conditions when the pressure behind the plastic front reaches a giant value p ∼ 1 Mbar at which the melting of the metal begins. It has been shown that superelasticity should be taken into account to correctly interpret the preceding laser experiments.     

冲击加载下Zr51Ti5Ni10Cu25Al9金属玻璃的塑性行为

进行了10—27 GPa应力范围内Zr₅₁Ti₅Ni₁₀Cu₂₅Al₉金属玻璃的平面冲击实验以研究其高压-高应变率加载下的塑性行为.由样品自由面粒子速度剖面的分析获得了冲击加载过程的轴向应力,并通过轴向应力与静水压线的比较获得剪应力.实验结果表明,尽管存在明显的松弛效应,但Zr基金属玻璃的Hugoniot弹性极限随着冲击应力的增加而增加.然而,塑性波阵面上的剪应力则显示先硬化而后软化现象,而且软化的幅度随冲击应力的增加而增加.冲击加载下Zr基金属玻璃的上述剪应力变化特征与分子动力学模拟结果比较一致,但与压剪实验结果和一维应力冲击实验结果明显不同.     

Anomalies in the temperature dependences of the bulk and shear strength of aluminum single crystals in the submicrosecond range

The results of measurements of the dynamic yield stress and the ultimate strength of aluminum single crystals in the temperature range from 15 to 650°C, which is only 10°C lower than the melting point, are presented. The measurements are made on samples under the action of plane shock waves with a pressure up to 5 GPa behind the front and of a duration of ～2×10^?7 s. It is found that the dynamic yield stress anomalously increases, attaining, in the vicinity of the melting point, a value four times as high as that measured at room temperature. The dynamic strength of the single crystals in this temperature range decreases approximately by 40%, a high strength being preserved in the state in which melting during extension is expected.     

Relaxation processes in metals at high strain rates

Mathematical modeling is used for experiments involving the loading of plates by plane shock waves to study the relaxation of shear stresses during the high-rate deformation of metallic materials. It is established that the characteristic relaxation times vary broadly — from fractions of a nanosecond to several microseconds. Such variation is indicative of a change in the mechanism responsible for relaxation. As a result, there is a difference between the quasi-equilibrium shear stresses in the elastic precursor and the same stresses behind the shock front. Metallic materials remain capable of resisting plastic deformation behind the front. Structural irregularities created by high-rate deformation result in localization of plastic flow at the microscopic level, which in turn causes the parameters of the stress-strain state at this level to differ from the corresponding parameters on the macroscopic scale.Siberian Physico-Technical Institute, affiliated with Tomsk University. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 8, pp. 82–90, August, 1995.     

Aluminum oxidation in shock and detonation waves

Experimental data on the detonation velocity of aluminized explosives and the temperature of the material behind the shock wave front in condensed media, including aluminum-oxidizer mixtures were examined. It was demonstrated that the oxidation of aluminum to the highest oxide behind the front of shock and detonation waves is limited by the dissociation of aluminum oxides at temperatures above 3.5 kK.     

凝聚炸药爆轰波在高声速材料界面上的折射现象分析

凝聚炸药爆轰在边界高声速材料约束下传播时,爆轰波会在约束材料界面上产生复杂的折射现象.本文针对凝聚炸药爆轰波在高声速材料界面上的折射现象展开理论和数值模拟分析.首先通过建立在爆轰ZND模型上的改进爆轰波极曲线理论给出爆轰波折射类型,然后发展一种求解爆轰反应流动方程的基于特征理论的二阶单元中心型Lagrange计算方法来数值模拟典型的爆轰波折射过程.从改进爆轰波极曲线理论和二阶Lagrange方法数值模拟给出的结果看出,凝聚炸药爆轰波在高声速材料界面上的折射类型有四种:反射冲击波的正规折射、带束缚前驱波的非正规折射、带双Mach反射的非正规折射、带λ波结构的非正规折射.     

粘性物质中正激波稳定性分析

用线性稳定性理论,分析粘性物质中的正激波稳定性问题.粘性物质中任意强度的一维激波,其稳定性问题可归结为处理复数范围内的特征值问题,该特征值问题由两个一阶常微分方程及一个二阶常微分方程构成.这些常微分方程的系数依赖于流动的基本流场的物理量及其梯度.所获得的特征值问题由一个四阶精度的有限差分离散求解.分析考虑物质粘性的金属铝中的正激波稳定性,可以看出,正激波运动是稳定的,并且激波速度对波前和波后的小扰动量的衰减有相反的作用,而物质粘性有致稳的作用.     

Effect of a fullerene C60 addition on the strength properties of nanocrystalline copper and aluminum under shock-wave loading

The Hugoniot elastic limit and the spall strength of aluminum and copper samples pressed from a mixture of a metallic powder and 2–5 wt % C₆₀ fullerene powder are measured under a shock loading pressure up to 6 GPa and a strain rate of 10⁵ s^?1 by recording and analyzing full wave profiles using a VISAR laser interferometer. It is shown that a 5% C₆₀ fullerene addition to an initial aluminum sample leads to an increase in its Hugoniot elastic limit by an order of magnitude. Mixture copper samples with 2% fullerene also exhibit a multiple increase in the elastic limit as compared to commercial-grade copper. The elastic limits calculated from the wave profiles are 0.82–1.56 GPa for aluminum samples and 1.35–3.46 GPa for copper samples depending on the sample porosity. The spall strength of both aluminum and copper samples with fullerene additions decreases approximately threefold because of the effect of high-hardness fullerene particles, which serve as tensile stress concentrators in a material under dynamic fracture.     

Reshock Response of 2A12 Aluminum Alloy at High Pressures

By means of mounting the specimen on a low-impedance buffer, reshock experiments were carried out on a 2A12 almninum alloy up to shock stresses＇ of 67.6 GPa. Reshock wave profiles from the initial shock stresses of 60.9-67.6 GPa were measured with a velocity interferometer, and it shows that the 2A12 aluminum alloy characterizes as quasi-elastic response during recompression process. The Lagrange longitudinal velocities along the reloading path from initial shock state were obtained from two shots of experiments, while the bulk velocities at corresponding shock stresses were determined via extrapolating from the public reported unloading plastic sound velocities. Combining the reshock and the release experimental results, the yield strength of 2A12 aluminum alloy at shock stress of 60.9 GPa was estimated to be about 1.7GPa.     

Shock adiabat features,phase transition macrokinetics,and spall fracture of iron in different phase states

Abstract

Results are presented of systematic experimental investigations of shock adiabat and evolution of multiwave configurations for a number of steels in the range up to 100GPa; of stress relaxation kinetics in the front of the elastic and phase precursor from different initial states: uσ_x = 15, 25, 49, and 59GPa; and of data on spa11 fracture of iron in α —, ε —, γ —, and liquid phases under conditions of uniaxial deformation as well as under volumetric omnidirectional tension. Changes in material microstructure and microhardness of samples subjected to shock wave loads of 15, 25, 200, and 1000 GPa are analyzed.

Investigations of steels with the initial state in α and γ phases of iron and with different original heat treatment show that, in stress waves of low intensity (σ_x? 10–25 GPa), as well as under quasi-static tension-compression tests and impact tests, differences in their behavior and properties are clearly displayed. As the amplitude of longitudinal stresses increases up to 200–250 GPa, differences in their compressibility and in the character of spal1 fracture begin to smooth down.     

铝的动态屈服强度测量及再加载弹性前驱波的形成机理分析

利用激光干涉测速技术(VISAR)测量LY12铝合金在20—34 GPa冲击压力下经历加载-卸载和加载-再加载过程的样品/窗口界面粒子速度剖面,采用AC方法确定了具有较高精度的动态屈服强度值.实验结果和文献发表的数据具有较好的一致性.通过以平面焊接方式制作组合飞片,克服了组合飞片在气炮发射过程中可能发生分离的技术困难,使铝的动态屈服强度测量压力范围从22 GPa扩展到了34 GPa.同时,根据对不同实验条件下的加载-再加载过程的比较,对再加载弹性前驱波的形成机理进行了讨论,认为位错是形成该现象的主要原因. 关键词： 动态屈服强度 AC方法 弹性前驱波 VISAR     

Viscosity of aluminum under shock-loading conditions

A reliable data treatment method is critical for viscosity measurements using the disturbance amplitude damping method of shock waves. In this paper the finite difference method is used to obtain the numerical solutions for the disturbance amplitude damping behaviour of the sinusoidal shock front in a flyer-impact experiment. The disturbance amplitude damping curves are used to depict the numerical solutions of viscous flow. By fitting the experimental data to the numerical solutions of different viscosities, we find that the effective shear viscosity coefficients of shocked aluminum at pressures of 42, 78 and 101 GPa are (1500±100) Pa · s, (2800±100) Pa · s and (3500±100) Pa · s respectively. It is clear that the shear viscosity of aluminum increases with an increase in shock pressure, so aluminum does not melt below a shock pressure of 101 GPa. This conclusion is consistent with the sound velocity measurement.     

铝的动态屈服强度测量及再加载弹性前驱波的形成机理分析

利用激光干涉测速技术(VISAR)测量LY12铝合金在20—34 GPa冲击压力下经历加载-卸载和加载-再加载过程的样品/窗口界面粒子速度剖面，采用AC方法确定了具有较高精度的动态屈服强度值.实验结果和文献发表的数据具有较好的一致性.通过以平面焊接方式制作组合飞片，克服了组合飞片在气炮发射过程中可能发生分离的技术困难，使铝的动态屈服强度测量压力范围从22 GPa扩展到了34 GPa.同时，根据对不同实验条件下的加载-再加载过程的比较，对再加载弹性前驱波的形成机理进行了讨论，认为位错是形成该现象的主要原因.     

Dissipative processes under the shock compression of glass

New experimental data on the behavior of the K8 and TF1 glasses under shock-wave loading conditions are obtained. It is found that the propagation of shock waves is close to the self-similar one in the maximum compression stress range 4-12 GPa. Deviations from a general deformation diagram, which are related to viscous dissipation, take place when the final state of compression is approached. The parameter region in which failure waves form in glass is found not to be limited to the elastic compression stress range, as was thought earlier. The failure front velocity increases with the shock compression stress. Outside the region covered by a failure wave, the glasses demonstrate a high tensile dynamic strength (6-7 GPa) in the case of elastic compression, and this strength is still very high after transition through the elastic limit in a compression wave.     

High strain rate deformation and fracture of the magnesium alloy Ma2-1 under shock wave loading

This paper presents the results of measurements of the dynamic elastic limit and spall strength under shock wave loading of specimens of the magnesium alloy Ma2-1 with a thickness ranging from 0.25 to 10 mm at normal and elevated (to 550°C) temperatures. From the results of measurements of the decay of the elastic precursor of a shock compression wave, it has been found that the plastic strain rate behind the front of the elastic precursor decreases from 2 × 10⁵ s^?1 at a distance of 0.25 mm to 10³ s^?1 at a distance of 10 mm. The plastic strain rate in a shock wave is one order of magnitude higher than that in the elastic precursor at the same value of the shear stress. The spall strength of the alloy decreases as the solidus temperature is approached.     

Strength and failure of LK7 borosilicate glass under shock compression

The Hugoniot elastic limit (HEL), the spall strength, the failure threshold, and the failure wave velocity in LK7 glass during shock compression are measured. The HEL estimated from the profiles of compression waves of various intensities is 7.1 ± 0.1 GPa. The spall strength exceeds 7 GPa during shock compression in the elastic range and remains high when passing through the HEL. Failure waves form in the stress range from 5.7 to 10.3 ± 0.5 GPa.     

冲击压缩下铝、铜、钨的剪切模量和屈服强度与压力和温度的相关性

对铝、铜和钨在冲击压缩状态下的剪切模量和屈服强度的实验数据进行了综合分析，并与St einberg-Cochran-Guinan(SCG)模型的计算结果进行了比较，结果表明，铝在50 GPa、铜在1 00 GPa、钨在200 GPa冲击压力以内，三种材料的剪切模量和屈服强度随温度和压力的变化 趋势基本相似，即SCG模型的假设Y′_pY₀=G′_pG ₀,Y′_TY₀=G′_TG₀对这三种材料在上述冲击压力范围内近似成立，利用该模型可以较好地描述材料在冲击压缩 下的本构行为. 关键词： 剪切模量 屈服强度 压力 温度     

Numerical study of converging shock waves in porous media

The dependences of the solutions to the hydrodynamic equations of compressed media that describe converging shock waves on the density of a substance ahead of a wave front are studied. The properties of Hugoniot adiabats that can explain the qualitatively different characters of these dependences for the equations of state of perfect gas and condensed matter are analyzed. The one-dimensional problems of converging shock waves in graphite and aluminum are considered, and the two-dimensional problem of the compression of graphite in a steel target with a conical cavity is solved. The latter problem is also investigated in terms of a simple model for a deformable solid that takes into account shear stresses.