Determination of styrene in olive oil by an automatic purge-and-trap system coupled to gas chromatography-mass spectrometry

Summary A new gas chromatographic method using an automatic purge-and-trap system coupled to a GC with mass selective detection to analyze styrene at the parts-per-trillions (ng kg^–1) level is described. The method shows a good sensitivity and the detection limit is 10 ng kg^–1 with a relative standard deviation (RSD) of 4.7% for 164 ng kg^–1 styrene in olive oil. This analytical method has been successfully applied to the analysis of styrene in extra-virgin olive oil from the European market.     

Determination ofm-xylylenediamine in the official EU food simulant olive oil

Summary EU Directive 90/128/EEC prescribes a specific migration limit (SML) of 0.05 mg kg⁻¹ for the aliphatic diaminem-xylylenediamine (XDA) into food or food simulants, but there is no generally accepted method of analysis available for testing compliance with this restriction.m-XDA has been determined in olive oil (EU food simulant for fatty foods) by high-performance liquid chromatography (HPLC) with fluorescence detection, after extraction into an aqueous phase and derivatization with fluorescamine. The method is appropriate for the quantitative determination ofm-XDA at a minimum level of 0.02 mg kg⁻¹ in this food simulant. The method should also be applicable to other fatty-food simulants (sunflower oil and HB 307).     

Rapid determination of BTEXS in olives and olive oil by headspace-gas chromatography/mass spectrometry (HS-GC-MS)

In this work, a straightforward, reliable and effective automated method has been developed for the direct determination of monoaromatic volatile BTEXS group (namely benzene, toluene, ethylbenzene, o-, m- and p-xylenes, and styrene) in olives and olive oil, based on headspace technique. Separation, identification and quantitation were carried out by headspace-gas chromatography-mass spectrometry (HS-GC-MS) in selected ion monitoring (SIM) mode. Sample pretreatment or clean-up were not necessary (besides olives milling) because the olives and olive oil samples are put directly into an HS vial, automatically processed by HS and then injected in the GC-MS for chromatographic analysis. The chemical and instrumental variables were optimized using spiked olives and olive oil samples at 50 μg kg⁻¹ of each targeted species. The method was validated to ensure the quality of the results. The precision was satisfactory with relative standard deviations (RSD (%)) in the range 1.6-5.2% and 10.3-14.2% for olive oil and olives, respectively. Limits of detection were in the range 0.1-7.4 and 0.4-4.4 μg kg⁻¹ for olive oil and olives, respectively. Finally, the proposed method was applied to the analysis of real olives and olive oil samples, finding positives of the studied compounds, with overall BTEXS concentration levels in the range 23-332 μg kg⁻¹ and 4.2-87 μg kg⁻¹ for olive oil and olives, respectively.     

Fast quantitation of 5-hydroxymethylfurfural in honey using planar chromatography

An approach for rapid quantitation of 5-hydroxymethylfurfural (HMF) in honey using planar chromatography is suggested for the first time. In high-performance thin-layer chromatography (HPTLC) the migration time is approximately 5 min. Detection is performed by absorbance measurement at 290 nm. Polynomial calibration in the matrix over a range of 1:80 showed correlation coefficients, r, of ≥ 0.9997 for peak areas and ≥ 0.9996 for peak heights. Repeatability in the matrix confirmed the suitability of HPTLC–UV for quantitation of HMF in honey. The relative standard deviation (RSD, %, n = 6) of HMF at 10 ng/band was 2.9% (peak height) and 5.2% (peak area); it was 0.6% and 1.0%, respectively, at 100 ng/band. Other possible detection modes, for example fluorescence measurement after post-chromatographic derivatization and mass spectrometric detection, were also evaluated and can coupling can be used as an additional tool when it is necessary to confirm the results of prior quantitation by HPTLC–UV. The confirmation is provided by monitoring the HMF sodium adduct [M + Na]⁺ at m/z 149 followed by quantitation in TIC or SIM mode. Detection limits for HPTLC–UV, HPTLC–MS (TIC), and HPTLC–MS (SIM) were 0.8 ng/band, 4 ng/band, and 0.9 ng/band, respectively. If 12 μL honey solution was applied to an HPTLC plate, the respective detection limits for HMF in honey corresponded to 0.6 mg kg⁻¹. Thus, the developed method was highly suitable for quantitation of HMF in honey at the strictest regulated level of 15 mg kg⁻¹. Comparison of HPTLC–UV detection with HPTLC–MS showed findings were comparable, with a mean deviation of 5.1 mg kg⁻¹ for quantitation in SIM mode and 6.1 mg kg⁻¹ for quantitation in TIC mode. The mean deviation of the HPTLC method compared with the HPLC method was 0.9 mg kg^-1 HMF in honey. Re-evaluation of the same HPTLC plate after one month showed a deviation of 0.5 mg kg⁻¹ HMF in honey. It was demonstrated that the proposed HPTLC method is an effective method for HMF quantitation in honey.      

Simple and Rapid Determination of Benzoylphenylurea Pesticides in River Water and Vegetables by LC–ESI-MS

Liquid chromatography with electrospray mass spectrometry (LC–ESI-MS) instrumentation equipped with a single quadrupole mass filter has been used to determine several benzoylphenylurea insecticides (diflubenzuron, triflumuron, hexaflumuron, lufenuron and flufenoxuron). Chromatographic and MS parameters were optimised to obtain the best sensitivity and selectivity for all pesticides. Solid-phase extraction (SPE) using C₁₈ cartridges was applied for preconcentration of pesticide trace levels in river water samples. Recoveries of benzoylphenylurea pesticides from spiked river water (0.01 and 0.025 μg L⁻¹) were between 73 and 110% and detection limits were between 3.5 and 7.5 ng L⁻¹. The applicability of the method to the determination of benzoylphenylurea insecticides in spiked cucumber, green beans, tomatoes and aubergines was evaluated. Samples were extracted into dichloromethane without any clean-up step. The limits of detection ranged from 1.0 to 3.2 ng mL⁻¹ (0.68 and 2.13 μg kg⁻¹ in the vegetable samples). Mean recoveries ranged from 79 to 114% at spiking levels of 0.01 and 0.03 mg kg⁻¹. The method was applied to determine traces of benzoylphenylureas in both river water and vegetable samples with precision values lower than 10%. Interferences due to the matrix effect were overcome using matrix-matched standards.     

HPLC Determination of DCJW in Rat Plasma and Its Application to Pharmacokinetics Studies

A high-performance liquid chromatography–UV method for determining DCJW concentration in rat plasma was developed. The method described was applied to a pharmacokinetics study of intramuscular injection in rats. The plasma samples were deproteinized with acetonitrile in a one-step extraction. The HPLC assay was carried out using a VP-ODS column and the mobile phase consisting of acetonitrile–water (80:20, v/v) was used at a flow rate of 1.0 mL min⁻¹ for the effective eluting DCJW. The detection of the analyte peak area was achieved by setting a UV detector at 314 nm with no interfering plasma peak. The method was fully validated with the following validation parameters: linearity range 0.06–10 μg mL⁻¹ (r > 0.999); absolute recoveries of DCJW were 97.44–103.46% from rat plasma; limit of quantification, 0.06 μg mL⁻¹ and limit of detection, 0.02 μg mL⁻¹. The method was further used to determine the concentration–time profiles of DCJW in the rat plasma following intramuscular injection of DCJW solution at a dose of 1.2 mg kg⁻¹. Maximum plasma concentration (C _max) and area under the plasma concentration–time curve (AUC) for DCJW were 140.20 ng mL⁻¹ and 2405.28 ng h mL⁻¹.     

Determination of Eprinomectin in Bovine Urine and Feces Using HPLC with Fluorescence Detection

Eprinomectin is a novel and potent antiparasitic animal health drug. An analytical procedure for the determination of EPR in bovine urine and feces has been developed. The urine sample was centrifuged and alkalized with ammonia following solid phase extraction. The fecal sample was extracted with acetonitrile, defatted with hexane, cleaned-up using C18 cartridge. All samples were analyzed by high performance liquid chromatography with fluorescence detection after derivatization with N-methylimidazole. The limits of detection are 0.5 ng mL⁻¹ and 0.5 ng g⁻¹, respectively. Fortified at 2, 10, 50, and 100 ng mL⁻¹(ng g⁻¹), inter-assay recoveries of EPR in cattle urine and feces were in the range of 87.9–91.5% and 78.6–86.3%, with coefficients of variation of 5.4–10.2% and 1.4–7.2%, respectively. Intra-assay mean recoveries of the analytes were 82.2–86.5% and 79.6–87.3%, with coefficients of variation of 7.8–11.5% and 6.3–7.8%, respectively. The method was used to study the excretion of eprinomectin in bovine urine and feces after subcutaneous administration at a dose of 0.5 mg kg⁻¹.     

Development and validation of an HPLC method for the simultaneous determination of clozapine and desmethylclozapine in plasma of schizophrenic patients

Summary A high-performance liquid chromatographic method with amperometric detection has been developed for the determination of levels of clozapine (CLZ) and its active metabolite N-desmethylclozapine (DMC) in human plasma. The analysis was performed on a 5 μm C8 reversed phase column (150×4.6 mm i.d.), with acetonitrile-phosphate buffer (pH 3.5), as the mobile phase. The detection voltage was +800 mV and the cell and column temperature were 50°C. Linear responses were obtained between 2 ng mL⁻¹ and 100 ng mL⁻¹. Absolute recovery for both clozapine and desmethylclozapine exceeded 88% and the detection limit was 1 ng mL⁻¹. Repeatability, intermediate precision and accuracy were satisfactory. The method, which is rapid, sensitive and selective, has been applied to therapeutic drug monitoring in schizophrenic patients following administration of Leponex^? tablets. In 21 patients in steady state at a mean daily clozapine dosage of 358 mg (ranging from 150 to 500 mg day⁻¹), clozapine levels averaged 379 ng mL⁻¹ (ranging from 102 to 818 ng mL⁻¹) and DMC levels averaged 233 ng mL⁻¹ (ranging from 70 to 540 ng mL⁻¹). The method requires only a very small amount of plasma (100 μL), and thus it is suitable for pharmacokinetic studies, as well as for therapeutic drug monitoring.     

Determination and Pharmacokinetic Study of 10-O-Dimethylaminoethylginkgolide B in Rat Plasma by LC–MS

To evaluate the pharmacokinetics of a novel analogue of ginkgolide B, 10-O-dimethylaminoethylginkgolide B (XQ-1) in rat plasma in pre-clinical studies, a sensitive and specific liquid chromatographic method with electrospray ionization mass spectrometry detection (LC–ESI–MS) was developed and validated. After a simple extraction with ethyl acetate, XQ-1 was analyzed on a Shim-pack C18 column with a mobile phase of a mixture of 1 μmol L⁻¹ ammonium acetate containing 0.02% formic acid and methanol (55:45, v/v) at a flowrate of 0.3 mL min⁻¹. Detection was performed in selected ion monitoring (SIM) mode using target ions at [M + H]⁺ m/z 496.05 for XQ-1 and m/z 432.10 for the internal standard (lafutidine). Linearity was established for the concentration range from 2 to 1,000 ng mL⁻¹ . The extraction recoveries ranged from 86.0 to 89.9% in plasma at concentrations of 5, 50, and 500 ng mL⁻¹. The lower limit of quantification was 2 ng mL⁻¹ with 100 μL plasma. The validated method was successfully applied to a pharmacokinetic study after intragastic administration of XQ-1 mesylate in rats at a dose of 20 mg kg⁻¹.     

Determination of fumonisins B1 and B2 in Portuguese maize and maize-based samples by HPLC with fluorescence detection

Fumonisins B₁ (FB₁) and fumonisin B₂ (FB₂) are the main members of a family of mycotoxins produced by Fusarium verticillioides, Fusarium proliferatum, and other fungi species of the section Liseola. The present work shows the results of comparative studies using two different procedures for the analysis of fumonisins in maize and maize-based samples. The studied analytical methods involve extraction with methanol/water, dilution with PBS, and clean-up through immunoaffinity columns. Two reagents (o-phthaldialdehyde and naphthalene-2,3-dicarboxaldehyde) were studied for formation of fluorescent derivatives. The separation and identification were carried out by high-performance liquid chromatography with fluorescence detection. The optimized method for analysis of fumonisins in maize involved extraction with methanol/water (80:20), clean-up with an immunoaffinity column, and derivatization with naphthalene-2,3-dicarboxaldehyde (NDA). The limit of detection was 20 μg kg⁻¹ for FB₁ and 15 μg kg⁻¹ for FB₂. Recoveries of FB₁ and FB₂ ranged from 79% to 99.6% for maize fortified at 150 μg kg⁻¹ and 200 μg kg⁻¹, respectively, with within-day RSDs of 3.0 and 2.7%. The proposed method was applied to 31 samples, and the presence of fumonisins was found in 14 samples at concentrations ranging from 113 to 2,026 μg kg⁻¹. The estimated daily intake of fumonisins was 0.14 μg kg⁻¹ body weight per day.     

Multiresidue pesticide analysis of fruits by ultra-performance liquid chromatography tandem mass spectrometry

Ultra-performance liquid chromatography coupled to tandem mass spectrometry (UPLC–MS–MS) has been used for screening and quantification of 32 pesticides and metabolites in two fruit matrices. The compounds investigated belonged to different chemical families of insecticides, acaricides, fungicides, and herbicides; several metabolites were also included. Quantification was conducted using matrix-matched standards calibration; response was a linear function of concentration in the range tested (10–500 ng mL⁻¹). The method was validated with blank samples of lemon and raisin spiked at 0.01 and 0.1 mg kg⁻¹, and recoveries were satisfactory, between 70 and 110%, for most of the pesticides tested and relative standard deviations were below 15% (n = 5 at each spiking level). Excellent sensitivity resulted in limits of detection for all compounds well below 0.01 mg kg⁻¹, with the limit of quantification being validated at 0.01 mg kg⁻¹. The UPLC system generates narrow peaks (approx. 5 s), thus increasing peak height and improving sensitivity. This improved separation efficiency facilitates adequate resolution not only of the analytes but also of matrix interferences compared with conventional HPLC. The method developed could also resolve some geometric isomers. The main advantage of this approach is the high sample throughput achieved because of the short analysis time, which enables satisfactory separation of all the compounds in less than 5 min per sample.     

HPLC with Column Switching Coupled to APCI–MS for Pharmacokinetic Study of Amygdalin in Rabbit Plasma

A fast and validated assay was established for the pharmacokinetic study of amygdalin in Armeniacae Semen in rabbit. The method involved column switching (CS) enrichment, separation, post-column derivatization, and atmospheric pressure chemical ionization (APCI) mass spectrometric detection. Plasma sample was enriched by CS using a MAYI-ODS as the first column. Analytes of interest were isolated and analyzed on a second column of Zorbax SB-C₁₈. To detect amygdalin in plasma samples, a T-piece was connected between the HPLC outlet and the APCI source to add a mixture of dichloromethane and methanol to the eluent by an isocratic pump. Calibration graphs showed good linearity over a range of 1.0–1,280 ng mL⁻¹. The detection limit was 0.2 ng mL⁻¹. The intra- and inter-day accuracies were within 3.9%. The method was successfully applied to a study of the pharmacokinetics of amygdalin after an intravenous injection of amygdalin extracts to rabbits with a dose of 400 mg kg⁻¹. The results indicate that amygdalin is a one-compartment open model with a first order absorption phase.     

Study of the metabolism on tobacco-specific N-nitrosamines in the rabbit by solid-phase extraction and liquid chromatography–tandem mass spectrometry

Metabolism of four tobacco-specific N-nitrosamines (TSNAs), N′-nitrosonornicotine (NNN), N′-nitrosoanatabine (NAT), N′-nitrosoanabasine (NAB), and 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) has been studied by solid-phase extraction (SPE) and liquid chromatography–tandem mass spectrometry (LC–MS–MS). 4-(Methylnitrosamino)-4-(3-pyridyl)-1-butanol (iso-NNAL) was used as internal standard. SPE and LC–MS–MS was found to be a rapid, simple, sensitive, and selective method for analysis of TSNAs in rabbit serum. The relative standard deviation (R.S.D., n = 6) for analysis of 5 ng mL⁻¹ and 0.5 ng mL⁻¹ standards and of serum sample spiked with 5 ng mL⁻¹ standards of five TSNAs was 2.1–11% and recovery of 5 ng mL⁻¹ standards from serum was 100.2–112.9%. A good linear relationship was obtained between peak area ratio and concentration in the range of 0.2–100 ng mL⁻¹ for NNAL and 0.5–100 ng mL⁻¹ for other four TSNAs, with correlation coefficients (R ²) >0.99 (both linear and log–log regression). Detection limits for standards in solvent were between 0.04 and 0.10 ng mL⁻¹. Doses of TSNAs administered to rabbits via the auricular vein were 4.67 μg kg⁻¹ and 11.67 μg kg⁻¹, in accordance with the different levels in cigarettes. Metabolic curves were obtained for the four TSNAs and for 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL), a metabolite of NNK; on the basis of these curves we modeled metabolic kinetic equations for these TSNAs by nonlinear curve fitting.     

Enzyme-linked immunosorbent assay and colloidal gold immunoassay for sulphamethazine residues in edible animal foods: investigation of the effects of the analytical conditions and the sample matrix on assay performance

To determine sulphamethazine (SMZ) residues in edible animal foods (pig muscle, chicken muscle, egg, fish, milk and liver), a competitive direct enzyme-linked immunosorbent assay (ELISA) and a colloidal gold immunoassay were established. The limits of detection of the ELISA and the colloidal gold immunoassay were 0.02 and 0.5 μg kg⁻¹, respectively. The specificity of the ELISA developed to the SMZ was high according to the results of cross-reactivity testing with 14 kinds of sulphonamides. To obtain a more sensitive immunoassay, buffer solution (30 mmol L⁻¹ phosphate-buffered saline with 0.05% Tween 20, pH 8.5) was optimized through the whole test procedure. A simple and efficient extraction method for the rapid detection of SMZ residues in foods was developed, with recoveries between 74 and 117.5%. Matrix effects can be avoided by 1:10 dilution of pig muscle, chicken muscle, egg, fish, milk and liver with optimal buffer. The detection limit of SMZ was 5 μg kg⁻¹ in liver and 2 μg kg⁻¹ in the other five samples. For the validation of the ELISA tests, sample extracts were analysed by ELISA and high-performance liquid chromatography. The results obtained by these two methods showed a good correlation (r ²) which was greater than 0.9. The colloidal gold immunoassay presented in this assay was successfully applied to determine SMZ in pig muscle, milk and fish below or equal to the maximum residue level (20 μg kg⁻¹).     

Buffer Standards for the Physiological pH of the Zwitterionic Compound, TAPS, From 5 to 55 ∘C

The values of the second dissociation constant, pK ₂, and related thermodynamic quantities of N-[tris(hydroxymethyl)methyl-3-amino]propanesulfonic acid (TAPS) have already been reported at 12 temperatures over the temperature range 5–55 ^∘C, including 37 ^∘C. This paper reports the results for the pH of five equimolal buffer solutions with compositions: (a) TAPS (0.03 mol⋅kg⁻¹) + NaTAPS (0.03 mol⋅kg⁻¹); (b) TAPS (0.04 mol⋅ kg⁻¹) + NaTAPS (0.04 mol⋅kg⁻¹); (c) TAPS (0.05 mol⋅kg⁻¹) + NaTAPS (0.05 mol⋅kg⁻¹); (d) TAPS (0.06 mol⋅kg⁻¹) + NaTAPS (0.06 mol⋅kg⁻¹); and (d) TAPS (0.08 mol⋅kg⁻¹) + NaTAPS (0.08 mol⋅kg⁻¹). The remaining eight buffer solutions consist of saline media of the ionic strength I = 0.16 mol⋅kg⁻¹, matching closely to that of the physiological sample. The compositions are: (f) TAPS (0.04 mol-kg⁻¹) + NaTAPS (0.02 mol-kg⁻¹) + NaCl (0.14 mol⋅kg⁻¹); (g) TAPS (0.05 mol⋅kg⁻¹) + NaTAPS (0.04 mol⋅kg⁻¹) + NaCl (0.12 mol⋅kg⁻¹); (h) TAPS (0.6 mol⋅kg⁻¹) + NaTAPS (0.04 mol⋅kg⁻¹) + NaCl (0.12 mol⋅kg⁻¹); (i) TAPS (0.08 mol⋅kg⁻¹) + NaTAPS (0.06 mol⋅kg⁻¹) + NaCl (0.10 mol⋅kg⁻¹); (j) TAPS (0.04 mol⋅ kg⁻¹) + NaTAPS (0.04 mol⋅kg⁻¹) + NaCl (0.12 mol⋅kg⁻¹); (k) TAPS (0.05 mol⋅kg⁻¹) + NaTAPS (0.05 mol⋅kg⁻¹) + NaCl (0.11 mol⋅kg⁻¹); (l) TAPS (0.06 mol⋅kg⁻¹) + NaTAPS (0.06 mol⋅kg⁻¹) + NaCl (0.10 mol⋅kg⁻¹); and (m) TAPS (0.08 mol⋅kg⁻¹) + NaTAPS (0.08 mol⋅kg⁻¹) + NaCl (0.08 mol⋅kg⁻¹). These buffers are recommended as a pH standard for clinical measurements in the range of physiological application. Conventional pH values, designated as pH(s), for all 13 buffer solutions from 5 to 55 ^∘C have been calculated. The operational pH values with liquid junction corrections, at 25 and 37 ^∘C for buffer solutions, designated above as (b), (c), (d), (e), (j), (l), and (m); have been determined based on the difference in the values of the liquid junction potentials between the accepted phosphate standard and the buffer solutions under investigation.     

Analysis of 5-hydroxy-N-methyl-2-pyrrolidone and 2-hydroxy-N-methylsuccinimide in plasma

Summary A method for the determination of 5-hydroxy-N-methyl-2-pyrrolidone (5-HNMP) and 2-hydroxy-N-methylsuccinimide (2-HMSI) in plasma was developed. 5-HNMP and 2-HMSI are metabolites to the widely used organic solvent N-methyl-2pyrrolidone (NMP). The 5-HNMP and 2-HMSI were purified from plasma by C8 solid phase extraction, derivatised by bistrimethylsilyl trifluoroacetamid, and analysed by gas chromatography with mass spectrometric detection. For 5-HNMP, the precision was 2–7 % (120 and 780 ng mL⁻¹) and the detection limit was 6 ng mL⁻¹ (m/z 98). For 2-HMSI, the precision was 2–9 % (160 and 1000 ng mL⁻¹) and the detection limit was 4 ng mL⁻¹ (m/z 144). The method is applicable for analysis of plasma samples from workers exposed to NMP.     

Spatial trends of petroleum hydrocarbons in water and sediments

Seasonal changes in petroleum hydrocarbons in water and streambed sediment from selected oil-related areas of Ondo State, Nigeria have been examined using gravimetric and infrared methods. The highest and lowest total petroleum hydrocarbon concentrations (TPH) in water (sediments in brackets) gravimetrically were 3.49 mg L⁻¹ (199.3) mg kg⁻¹ and 0.003 mg L⁻¹ (81.0) mg kg⁻¹ while the concentrations found by IR were 24.0 mg L⁻¹ (135.0 mg kg⁻¹) and 14.0 mg L⁻¹ (33.0 mg kg⁻¹) respectively. The two seasons were positively correlated (α = 0.01) by both methods. The TPH level was well correlated with the sediment organic carbon (OC) during both seasons. The characteristic carbonyl (C=O) vibrations at 1650 cm⁻¹ and 1700 cm⁻¹ indicate oxidation of the oil residue. The study recommends further investigation into the type of organics present to evaluate their toxicity and appropriate remediation.      

Determination of antibacterials in animal feed by pressurized liquid extraction followed by online purification and liquid chromatography-electrospray tandem mass spectrometry

A fully automated method has been developed for analysis of eighteen antibacterial compounds, including penicillins, cephalosporins and sulfonamides, in animal feed with limits of quantification in the range 0.25–5.79 μg kg⁻¹. The method is based on pressurized liquid extraction of 3 g homogenized feed with water and online clean-up of 500 μL of the extract with C₁₈HD cartridges. The purified sample was directly analysed by liquid chromatography–electrospray tandem mass spectrometry (SPE–LC–ESI-MS–MS). Chromatographic separation was achieved within 10 min by use of a C₁₂ Phenomenex Hydro-RP reversed-phase analytical column and a mobile phase gradient (water + 0.1% formic acid–methanol + 0.1% formic acid). The method was validated, revealing capability for detection of concentrations as low as 0.09 μg kg⁻¹, decision limits (CCα) and detection capabilities (CCβ) in the range 10–174 μg kg⁻¹ and 22–182 μg kg⁻¹, respectively, and inter-day precision ranging from 0.7 to 8.3%. Recovery, with internal standard correction, was in the range 93–134% for all analytes. The method was then applied to analysis of fifteen feed samples, nine of which contained at least one antimicrobial at concentrations between 0.006 and 1.526 mg kg⁻¹. The performance data and results from the method were compared with those from a previous method developed by our group, using offline SPE, by analyzing the same set of samples by both methods. The online SPE approach resulted in slightly improved sensitivity, with LODs of 0.09–2.12 μg kg⁻¹ compared with 0.12–3.94 μg kg⁻¹ by the offline approach. In general, better recovery was achieved by use of online purification (for 72% of the analytes) and the correlation between the two methods was good. The main advantages of the new online method are rapid and automated sample pre-treatment, and reduction of sample manipulation, enabling high-throughput analysis and highly accurate results. Because of all these characteristics, the proposed method is applicable and could be deemed necessary within the field of food control and safety.     

Determination of total Sb,Se, Te,and Bi and evaluation of their inorganic species in garlic by hydride-generation–atomic-fluorescence spectrometry

A sensitive and simple analytical method has been developed for determination of Sb(III), Sb(V), Se(IV), Se(VI), Te(IV), Te(VI), and Bi(III) in garlic samples by using hydride-generation–atomic-fluorescence spectrometry (HG–AFS). The method is based on a single extraction of the inorganic species by sonication at room temperature with 1 mol L⁻¹ H₂SO₄ and washing of the solid phase with 0.1% (w/v) EDTA, followed by measurement of the corresponding hydrides generated under two different experimental conditions directly and after a pre-reduction step. The limit of detection of the method was 0.7 ng g⁻¹ for Sb(III), 1.0 ng g⁻¹ for Sb(V), 1.3 ng g⁻¹ for Se(IV), 1.0 ng g⁻¹ for Se(VI), 1.1 ng g⁻¹ for Te(IV), 0.5 ng g⁻¹ for Te(VI), and 0.9 ng g⁻¹ for Bi(III), in all cases expressed in terms of sample dry weight.     

Capillary zone electrophoresis determination of oxytetracycline in pig tissue samples at maximum residue limits

Summary The determination of the antibiotic oxytetracycline (OTC), in pig tissues was investigated by capillary zone electrophoresis (CZE) with a prior solid-phase extraction (SPE) using alkyl-bonded silica and polymeric cartridges. The methodology developed allows determination of OTC in pig kidney, liver and muscle samples with detection limits below maximum residue limit values, and the procedures to extract OTC and clean-up the matrix are simple and reliable. The limit of detection for OTC was 160, 120 and 85 μg kg⁻¹ for kidney, liver and muscle samples, respectively. The average recoveries from spiked samples (200 μg kg⁻¹ and 1600 μg kg⁻¹) were in excess of 63% with coefficients of variation between 2.0 and 9.8%. This method would be useful for routine monitoring of oxytetracycline residues in pig tissues.