PP/POE共混物的P-V-T属性及压力对结晶温度的影响

采用PVT膨胀仪研究了PP/POE共混物的P-V-T属性, 利用Tait方程预测其比容和热膨胀系数(α), 研究了压力对结晶温度(Tc)的影响. 结果表明, Tait状态方程可用来预测部分相容的、半结晶PP/POE共混物的PVT行为. PP结晶前后的比容变化比POE的大得多, 随着POE含量的增加, PP/POE共混物结晶前后比容的变化均逐渐减小. PP在熔融状态下的α比固体状态的大, 而POE正好相反. PP/POE共混物的α随温度和压力的变化与其组成密切相关. 随着压力的增高, PP, POE及其PP/POE共混物的结晶温度均呈线性增高的趋势.     

基于相形态的微孔发泡PP/POE共混物泡孔结构调控

采用挤出共混制备3种不同相形态的厚壁聚丙烯/乙烯-辛烯共聚物(PP/POE)共混物样品,并对样品在110℃发泡温度下进行高压釜发泡.利用共混物相形态以及两相黏弹性和超临界二氧化碳溶解度的差异,有效地调控厚壁样品内泡孔的形状、分布和尺寸等,获得了3种典型的泡孔结构.分散相呈椭球状液滴的80/20 PP/POE共混物发泡后泡孔呈椭球状,且两者具有相同数量级的平均直径和密度;分散相呈长纤维状的80/20共混物发泡后泡孔呈长孔状,两者的平均直径较为接近.呈部分共连续相结构的60/40共混物发泡后形成了具有较高连通度的开孔结构.进一步地,通过改变发泡温度,获得了更接近共混物中液滴状分散相平均直径和密度的近似球状的泡孔以及具有更高连通度的开孔结构.     

Non-isothermal crystallization and crystalline structure Of PP/POE blends

Polypropylene (PP) /ethylene-octene copolymer (POE) blends with different content of POE were prepared by mixing chamber of a Haake torque rheometer. The crystallization behaviors and crystal structure of PP/POE blends were systematically investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and polarized optical microscopy (POM). The results showed that PP spherulites became defective and the crystallization behavior was influenced intensely with the introduction of POE. At the low content of POE, the addition of POE decreases the apparent incubation period (Δt _i) and the apparent total crystallization period (Δt _c) of PP in blends due to the heterogeneous nucleation of POE, and small amount of β-form PP crystals form because of the existence of POE. However, at high content of POE, the addition of POE decreases the mobility of PP segments due to their strong intermolecular interaction and chain entanglements, resulting in retarding the crystallization of PP, decreasing in the amount of β-form PP crystals, and increasing in Δt _i and Δt _c of PP in blends.     

颗粒内受限聚合法制备PP/POE/PS合金

以等规聚丙烯/乙烯-辛烯共聚物(PP/POE)合金颗粒为扩散基体, 苯乙烯(St)为扩散单体, 利用颗粒内受限聚合法制备了PP/POE/PS三元合金. 结果表明, 对于POE质量分数为20%~40%的PP/POE合金颗粒, St均可扩散至直径为4 mm的颗粒中心部位, 在POE非晶相中生成相尺寸为几十至几百纳米的PS球. 在PP/POE合金颗粒的不同部位, 因POE相尺寸及单体的吸附量不同, 生成的PS相尺寸也不同, 在颗粒中心部位生成的PS球最小. 研究了St在PP/POE(质量比80: 20)颗粒中的扩散-聚合行为, 结果表明, St在合金颗粒中的扩散速率和扩散饱和值远大于在纯PP颗粒中的扩散速率和饱和值, 这主要是因为PP/POE合金颗粒中的非晶POE相有利于扩散. 改变单体投料量可以获得具有不同PS含量的PP/POE/PS三元合金. 结晶性能研究结果表明, PS在非晶POE相中的优先分布会使POE相体积增大, 从而使PP的结晶温度和熔融温度降低. 随着PS量的进一步增大, 分布在PP中的PS对PP有结晶成核作用.     

Dynamic Mechanical Behavior of PP/PET/MAPP Blends Filled with Glass Beads

PP/PET/MAPP blends have been filled with 50 wt% of glass beads. The orientation of the PP crystalline phase, the crystallization behavior and the dynamic mechanical response of these materials have been analyzed. The dynamic mechanical response is strongly affected by the presence of the glass beads, being possible to detect the effect of PET and MAPP on the storage modulus and loss factor values. Moreover, the alpha relaxation of the composites is visibly affected by thermal treatments.     

Phase Behavior of Polymer Blends

The present report deals with some results on phase behavior, miscibility and phase separation for several polymer blends casting from solutions. These blends are grouped as the amorphous polymer blends, blends containing a crystalline polymer or two crystalline polymers. The blends of PMMA/PVAc were miscible and underwent phase separation at elevated temperature, exhibited LCST behavior. The benzoylated PPO has both UCST and LCST nature. For the systems composed of crystalline polymer poly(ethylene oxide) and amorphous polyurethane, of two crystalline polymers poly(-caprolactone) and poly[3,3,-bis-(chloromethyl) oxetane], appear a single T_g, indicating these blends are miscible. The interaction parameter B's were determined to be –14 J cm^–3, –15 J cm^–3 respectively. Phase separation of phenolphthalein poly(ether ether sulfone)/PEO blends were discussed in terms of thermal properties, such as their melting and crystallization behavior.This revised version was published online in November 2005 with corrections to the Cover Date.     

PVC／PE交联共混体系的动态力学研究

在ＰＶＣ／ＰＥ共混体系中加入交联剂和引发剂能产生ＰＶＣ－ＣＯ－ＰＥ共聚物，这种共聚物在共混物中可起到增容剂的作用。通过动态力学分析和扫描电镜研究了ＰＶＣ／ＰＥ交联共混体系的相容性。发现引发剂、交联剂、稳定剂和增塑剂等对共混物中的交联反应均有较大的影响。     

辐射增强PP／BR共混体系的力学性能

研究了在多官能团单体－三烯丙基异氰酸酯存在下，共混体系聚丙烯／１．４－聚丁二烯橡胶的辐射效应，用ＤＳＣ，动态粘弹谱对其进行表征。结果显示，三烯丙基异氰酸酯主要分布于聚丙烯／１．４－聚丁二烯橡胶共混物的界面自高能射线作用下，被引发参与界面反应，从而改善了共混体系的相容性，增强也界面粘接，提高了共混物的力学性能。     

环氧树脂/聚碳酸酯固化共混物的结构及性能

相结构;酯交换反应;力学性能;环氧树脂/聚碳酸酯固化共混物的结构及性能     

Dynamic Mechanical Behavior of a Novel Polymeric Composite Damping Material

The dynamic mechanical behavior of a novel polymeric composite damping material has been investigated in this article. The composite consists of chlorinated polyethylene （CPE）, N,N-dicyclohexyl-2-benzothiazolylsufenamide （DZ）, 4,4＇-thio-bis（3-methyl-6-tert-buthylphenol） （BPSR） and vapor-grown carbon fiber （VGCF）. It is found that either the position or the intensity of damping peak can be controlled by changing the composition of CPE/DZ/BPSR composite. Within a certain composition region, damping peak maximum depends on CPE/DZ ratio, whereas damping peak position is controlled by BPSR content. Moreover, the improvement of storage modulus can be achieved by incorporation of VGCF. These results may imply that a damping material possessing both good damping properties and high strength can be designed and obtained.     

PES／PC共混体系的相容性与力学性能

ＰＥＳ／ＰＣ共混体系的相容性与力学性能姜振华，马荣堂，寇喜春，安立佳（吉林大学化学系长春）（中国科学院长春应用化学研究所长春１３００２２）关键词聚醚砜，聚碳酸酯，共混物，力学性能聚醚砜（ＰＥＳ）是一种性能优异的特种工程塑料，它具有强度高、刚性大、耐热...     

注压成型纳米结构PP/POE共混物表面的液滴低温冲击行为

以制备的阳极氧化不锈钢模板为模具嵌件, 采用注射压缩成型(ICM)工艺快速成型表面具有纳米丝结构的柔性聚丙烯/乙烯-辛烯共聚物(PP/POE, PP与POE质量比为3∶1)共混物复制物和准刚性PP复制物, 研究常温液滴冲击?10 ℃复制物表面的动态行为. 结果表明, 致密的纳米丝使复制物表面呈现超疏水、 极低黏附的润湿状态. 在低冲击速度范围内, 共混物复制物表面上液滴的接触时间比PP复制物上的短, 可归因于液滴铺展阶段柔性纳米丝储存的弹性势能在回缩阶段转换为液滴的动能; 在高冲击速度范围内, 共混物复制物基板和纳米丝储存的弹性势能被转换为液滴的动能, 进一步缩短了液滴的接触时间. 此结果表明, 共混物复制物的柔性和表面超疏水性使其具有优异的防冻黏性能. 共混物复制物表面上水滴(50 μL)的结冰时间得到明显延长、 冰黏附强度明显降低. 研究结果表明, 可采用ICM快速成型具有优异防冻黏和防冰性能的柔性超疏水高分子材料表面.     

Mechanical and Rheological Behavior of Unvulcanized and Dynamically Vulcanized i-PP/EPDM Blends

The mechanical and rheological behavior of dynamically vulcanized PP/EPDM blends is examined and compared with those of unvulcanized blends. The effect of blend ratio and dynamic vulcanization of EPDM rubber on tensile properties and flow are investigated. The mechanical properties of the blends are strongly influenced by the blend ratio. With the increasing of EPDM content the value of yield stress in a solid state decreases with the elastomer volume fractions less than 0.45 for the unvulcanized blends. For the dynamically vulcanized blends the interval of EPDM content, at which the yield peak is seen, is rather limited below 0.25 elastomer volume fractions. It is shown that dynamic vulcanization changes the deformational behavior of PP/EPDM blends. The rheological properties of dynamically vulcanized blends depending on the ratio of the components may be similar to the properties of polymer composites containing the highly disperse structuring filler. The distinction between the rheological behavior of unvulcanized and dynamically vulcanized blends is related to differences of their structures and viscoelastic characteristics of unvulcanized and vulcanized EPDM phase.     

HIPS／PP熔融反应共混及其动态力学性质

研究了高抗冲聚苯乙烯（HIPS）／聚丙烯（PP）共混物在过氧化二异丙苯（DCP）存在下的熔融反应过程及其动态力学性质．HIPS在DCP存在下以聚苯乙烯（PS）的降解为主，伴随着聚丁二烯（PB）的交联和接枝，PP在DCP存在下以降解为主，HIPS／PP在DCP存在下以PP同HIPS的反应接枝为主，这种原位生成的增容剂显著地改善了HIPS／PP两组份间的相容性，其分子运动特征较前两者发生明显变化，PS的Tg下降，PB和PP的Tg升高．     

Miscibility and Mechanical Behavior of SAN/NBR Blends

Summary: Aiming the development of high toughness polymer materials, blends of poly(styrene-co-acrylonitrile) (SAN) and poly(butadiene-co-acrylonitrile) (NBR) rubbers, with contents of acrylonitrile (AN) varying from 21 to 45%, were prepared by casting, coprecipitation and monoscrew extrusion followed by injection molding. SAN/NBR blends, prepared in the compositions (w/w) 90/10, 80/20, 70/30, 60/40, and 50/50, were characterized by differential scanning calorimetry (DSC) and Izod impact tests. DSC analyses showed that blends with 33% AN NBR prepared by casting, and with 39% AN NBR prepared by coprecipitation, are partially miscible at 60/40, 70/30 and 80/20 (SAN/NBR) compositions and immiscible for 50/50 compositions. On the other hand, 90/10 SAN/NBR systems were totally miscible. The blends with 45% AN NBR prepared by coprecipitation showed partial miscibility to 50/50, 60/40, 70/30 and 90/10 compositions and total miscibility to 80/20 composition. The NBR addition results in a significant increase in the impact resistance, strongly dependent on the blend composition and the NBR AN content. The best result of impact resistance — 75.2 ± 8.6 (kJ · m⁻²) — was obtained for SAN/NBR 50/50, using 45% AN NBR. This value is 15.7 times bigger than that for pure SAN -4.8 ± 0.7 (kJ · m⁻²).     

联苯型聚酰亚胺纤维的动态力学行为

采用干湿法纺丝工艺路线制备联苯型聚酰亚胺(PI)纤维,用动态力学分析方法研究了该纤雏的γ、β和α转变,因所施频率的不同而发生的相应转变温度分别出现在-100--40℃、100℃和270-300℃。用类似的Arrhenius方程计算了PI纤维γ转变活化能为38．7kJ／mol,α转变的活化能为853kJ／mol。     

Intumescent flame retardation and silane crosslinking of PP/EPDM elastomer

This study deals with the silane crosslinking and intumescent flame retardation of polypropylene/ethylene‐propylene‐diene copolymer (PP/EPDM) elastomers. The effect of silane crosslinking on the flame retardancy of the PP/EPDM composites containing melamine phosphate (MP) and dipentaerythritol (DPER) was studied by limiting oxygen index, UL 94 and cone calorimetry tests. The chemical composition of the silane crosslinked and flame retarded PP/EPDM composites treated at different temperatures was studied by X‐ray photoelectron spectroscopy and real time Fourier transform infrared (FTIR) spectrometry. Thermal decomposition and crystallization behavior of the PP/EPDM composites were investigated using thermogravimetric analysis and differential scanning calorimetry, respectively. Moreover, the mechanical properties of the composites were also studied. It is found that the flame retardancy, mechanical properties, and thermal decomposition behavior of the composites are influenced by silane grafting and crosslinking. Copyright © 2008 John Wiley & Sons, Ltd.     

反应性单体改性PP/PS共混物结晶与熔融行为

制备了三种反应性单体和两种PP接枝物改性的PP／PS共混物,用DSC研究了改性PP／PS共混物的结晶与熔融行为。结果表明：PS的加入提高了PP的结晶温度,两种接枝物的加入进一步提高共混物中PP的结晶温度,少量反应性单体对结晶温度影响不大,但高用量时则明显提高共混物的结晶温度;外加接枝物或者反应性单体对共混物中PP的熔融温度影响不大,但是熔融峰形与结晶温度高低有关。