首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
将经聚二烯丙基二甲基氯化铵(PDDA)预处理的HZSM-5分子筛置于SAPO-11分子筛的合成母液中, 在水热体系中原位制备了一系列HZSM-5/SAPO-11复合分子筛, 并对分子筛的结构、 形貌及酸性进行了表征, 考察了其在异丁烷芳构化反应中的催化性能. 结果表明, 所得复合分子筛由HZSM-5表面包覆约20 nm的SAPO-11微晶组成, 且通过调变SAPO-11的Si含量可以有效调变复合分子筛的酸性, 提高芳构化强弱酸协同催化作用, 有效抑制裂解副反应. 结合异丁烷芳构化转化率及液体收率结果可知, 当SAPO-11合成溶胶中硅铝摩尔比为0.6时, HZSM-5/SAPO-11复合分子筛的芳构化活性及稳定性最佳.  相似文献   

2.
《Microporous Materials》1995,3(4-5):401-408
Molecular diffusion of methane and tetrafluoromethane in the microporous material VPI-5 was studied by pulsed field gradient nuclear magnetic resonance (PFG NMR) and NMR exchange experiments. The translational mobility of both molecules in VPI-5 was found to be at least two orders of magnitude smaller than in ZSM-5. This is surprising since the channels in VPI-5 are about two times as wide as those in ZSM-5. The surprisingly small translational mobility in VPI-5 could be caused by a more complete stabilization effect or by single-file diffusion. The intracrystalline mean life time of methane in VPI-5 directly measured in the NMR tracer exchange experiments was found to be in satisfactory agreement with the value estimated on the basis of the PFG NMR data on translational mobility for ordinary intracrystalline diffusion. It must be ruled out, therefore, that molecular transportation over length scales of the order of the crystallite dimensions is controlled by single-file diffusion.  相似文献   

3.
We study the tracer exchange of molecules between the phase adsorbed in one-dimensional channels and the surrounding gas phase by molecular dynamics simulations. Under the conditions of single-file diffusion, a novel boundary effect is observed. The shape of the tracer-exchange concentration profiles deviates from those obtained under the conditions of normal diffusion. Compared to the profiles for normal diffusion, which correspond to the same degree of exchange, the equilibrium concentration is reached faster at the boundaries and slower in the middle part of the channel in the case of single-file diffusion. This boundary effect is observed for the system neopentane in AlPO4-5 (which was chosen as a reference system), as well as for modified systems. The effect can be understood considering two diffusion mechanisms which occur in parallel. First, the diffusion of the whole chain of particles, that is, the center-of-mass diffusion, obeying the laws of normal diffusion. Second, the individual movement of the particles relative to the center of mass of the chain. The second mechanism admits additional displacements which, on average, lead to an accelerated exchange of the marginal particles.  相似文献   

4.
ZSM-5 (core)/SAPO-11 (shell) composite molecular sieve was synthesized by the hydrothermal method in order to combine the advantages of ZSM-5 and SAPO-11 for the methylation of naphthalene with methanol. For comparison, the mechanical mixture was prepared through the blending of ZSM-5 and SAPO-11. The characterization results indicated that ZSM-5/SAPO-11 composite molecular sieve exhibited a core–shell structure, with the ZSM-5 phase as the core and the SAPO-11 phase as the shell. The pore size of the composite was between that of ZSM-5 and SAPO-11. The composite had fewer acid sites than ZSM-5 and mechanical mixture while more acid sites than SAPO-11. The experimental results indicated that the composite exhibited high catalytic performances for the methylation of naphthalene with methanol.  相似文献   

5.
The alkylation of toluene with methanol to selective formation of p-xylene has been systematically studied. ZSM-12 (MTW)/ZSM-5 co-crystalline zeolite in 40:60 proportions have been synthesized by the same molar gel composition, but at different temperatures and periods than that of ZSM-12 and ZSM-5, separately. All the prepared samples are characterized by XRD, SEM, BET, and XRF. The activity of toluene alkylation was investigated with a mixture of toluene and methanol as a feed over the ZSM-12, ZSM-12/ZSM-5 co-crystalline, ZSM-5, and physical mixture of ZSM-12/ZSM-5. Prom characterization, it is observed that the ZSM-12/ZSM-5 co-crystalline material is different from that of ZSM-12, ZSM-5, and their physical mixture. Further, the ZSM-12/ZSM-5 co-crystalline zeolite produces the highest content of xylene and has better selectivity for p-xylene than ZSM-12, ZSM-5, and their physical mixture.  相似文献   

6.
用固体离子交换法制备了V2O5/ZSM-5和V2O5/丝光沸石两类催化剂。通过XRD,LRS,XPS和Sg测定表征了V2O5在分子筛上的分散状态。用吡啶吸附红外光谱法和正丁胺非水溶液回滴法研究了催化剂的表面酸性。用ESR研究了甲苯在催化剂上的吸附。结果表明,催化剂的酸性不同,它们吸附甲苯的能力也不同,对甲苯气相选择氧化的活性和选择性也有较大的差异。同时,甲苯选择氧化成苯甲醛的能力还与V2O5在分子  相似文献   

7.
Palladium-containing zeolites catalyze the cycloisomerization of diethyl diallylmalonate to dimethylcyclopentenes. When the reaction is carried out in toluene, the performance of the palladium catalyst depends on the pore size of the zeolites. At 60 °C, palladium adsorbed on large pore size Beta zeolite (pore size ∼7.4 Å) is more active than medium pore size ZSM-5 (pore size ∼5.4 Å). This lower activity of ZSM-5 compared to Beta is attributable to the restricted diffusion of reagent and products through the ZSM-5 channels as compared to Beta zeolite. However, due to the gas-like diffusion characteristic of the supercritical state, the activity of ZSM-5 increases and becomes identical to that of Beta zeolite using supercritical CO2 as medium.  相似文献   

8.
通过分步晶化水热处理的方式合成了ZSM-5/SAPO-5复合材料。研究了两种分子筛凝胶的混合方式、调节ZSM-5母液的酸类型、SAPO-5凝胶组成以及晶化时间对复合材料形成的影响。实验结果表明,简单将两种分子筛的合成凝胶混合不能得到复合材料。采用H2SO4调节ZSM-5合成母液的pH值,在ZSM-5与SAPO-5理论质量比为3.5、SAPO-5凝胶中P2O5与Al2O3摩尔比为1.2的条件下可以得到ZSM-5/SAPO-5复合材料。但样品中含有少量无定形物质,这些无定形通过延长晶化时间并不能完全消除。  相似文献   

9.
Probing the mesopore architecture in mesoporous zeolites is of importance for large scale applications of the materials. In this work, the adsorption and diffusion of mesitylene with larger molecule size in mesoporous ZSM-5 zeolites were carried out, in order to acquaint the availability and interconnectivity of mesopores in zeolite crystals. The comparisons of the shape of adsorption isotherms and the mesopore volume calculated from mesitylene and N2 adsorption in mesoporous ZSM-5 zeolites with different mesoporosities can be used to discriminate two cases of mesopores: accessible mesopores connected to external surface of the zeolite crystals and non-accessible meso-voids that are occluded in the microporous matrix. Furthermore, the effective diffusivity and activation energy of mesitylene in mesoporous ZSM-5 extracted from ZLC desorption curves as a function of mesopore volume calculated from mesitylene adsorption reveal the enhancement of mesopore interconnectivity to molecule diffusion in zeolite crystals.  相似文献   

10.
以磷酸、拟薄水铝石和硅溶胶为原料, 三乙胺为模板剂, 采用气相转移法合成了一系列ZSM-5/SAPO-5复合分子筛. 产物经X射线衍射、扫描电镜、X射线能量散射谱、红外光谱及N2 静态吸附法等手段对其进行了表征, 证明合成材料是以ZSM-5为核、SAPO-5为壳的双结构分子筛. 实验结果表明, 干胶制备条件及液相组成都影响复合分子筛的结晶. 晶化温度的提高和晶化时间的延长有利于分子筛结晶度的提高. VPT法可以减小SAPO-5和复合分子筛颗粒的直径, 改善SAPO-5在ZSM-5分子筛表面的分布. 重油裂化结果表明, 核壳结构复合分子筛对生成低碳烯烃的性能优于机械混合的样品.  相似文献   

11.
选用SAPO-11、ZSM-22两种分子筛为载体,浸渍Pt制备了Pt/SAPO-11和Pt/ZSM-22催化剂,以正庚烷为模型化合物,考察乙醇对催化剂临氢异构化反应性能的影响。并通过BET、XRD、C2H5OH-TPD和C2H5OH-FTIR等表征手段对催化剂的物化性能以及吸附反应性能和不同活性酸性位点进行了研究考察。结果表明,乙醇在临氢异构转化过程优先生成H2O,并以H2O的形式影响催化剂的异构化性能,催化剂异构活性与选择性随乙醇含量的增加而降低。与Pt/ZSM-22催化剂相比,Pt/SAPO-11催化剂由于有P-OH基团,表现出一定的抗含氧化物乙醇的性能。  相似文献   

12.
通过水热法合成SAPO-34分子筛,将其制成催化剂用于催化丁烯转化制取丙烯,考察了反应温度、空速和铝磷比等对催化性能的影响;还比较了SAPO-34分子筛与ZSM-5分子筛催化该反应的差异.结果表明,在实验范围内,反应温度升高会使得丁烯的转化率明显增高,且丙烯选择性提高;而空速增加,则丁烯的转化率和丙烯选择性降低;铝磷比越大,对丙烯的选择性越差.在有效的反应时间内,SAPO-34分子筛催化效果好于ZSM-5分子筛,但单程寿命较ZSM-5分子筛短.  相似文献   

13.
詹必增  冯宏  胡锷  曾昭槐 《催化学报》1993,14(6):461-465
在综述甲苯择形烷基化机理并分析产生“反效应”的原因的基础上,提出了克制的“反向效应”的设想。Sb2O3,TiCl4,SiCl4,H3PO4,Mg(Ac)2等化合物对分子筛进行改性,测定改性前后分子筛的表面酸性与孔结构,关联乙基化反应结果,证实中强酸中心在乙基化反应中的重要作用,认为保持孔道的畅通是解决“反应效应”的关键。并采用了K-Mg改性,制备出对甲苯乙基化具有高初活性和高对位选择性的催化剂。  相似文献   

14.
A series of mesoporous UL-ZSM-5 materials (Si/Al = 50) with different micro- and mesoporosity as well as crystallinity was prepared following the procedure proposed in one of our recent studies (Trong-On, D.; Kaliaguine, S. Angew. Chem. Int. Ed. 2001, 40, 3248-3251. Trong-On, D.; Kaliaguine, S. U.S. Patent 6,669,924, B1, 2003). These materials have zeolitic structure in the form of nanoparticles intergrown in the walls of the amorphous wormhole-like aluminosilicate mesopores of Al-Meso-50, which was used as a precursor in the synthesis. The structure, crystallinity, and textural properties of the synthesized materials, as well as a reference ZSM-5 zeolite sample, were determined by X-ray diffraction (XRD), transmission electron microscopy (TEM)/scanning electron microscoy (SEM) analyses, Fourier transform infrared spectroscopy (FTIR), 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR), and nitrogen adsorption/desorption techniques. The acid properties were examined by FTIR of adsorbed pyridine. UL-ZSM-5 materials were shown to be highly hydrothermally stable. The diffusion of two C7 hydrocarbons, i.e., n-heptane and toluene, in four UL-ZSM-5 materials with different microporosities, related acidities, and crystallinities were investigated using the zero-length column (ZLC) method. Furthermore, the wormhole-like mesostructured aluminosilicate precursor (Al-Meso-50) and a reference MFI zeolite sample were also investigated using the same technique. A theoretical model considering a combination of mesopore diffusion (with surface slip in the main channels) with an activated, mainly surface diffusion mechanism in the intrawall biporous structure, was proposed and employed to interpret the experimental ZLC results. A classical Knudsen type of diffusion was replaced by an activated surface slip type of diffusion mechanism in the mesopores. The transport of n-heptane in UL-ZSM-5 materials was found to be mainly controlled by mesopore diffusion in the main-channel structure, while that of toluene was dominated by the intrawall diffusion process. Diffusion activation energies of n-heptane are about 2 times higher in comparison to toluene, which has a larger kinetic diameter. The main mesopore channel structure seems to appreciably contribute to the overall mass transport. Furthermore, the effect of hydrothermal treatment (20% steam at 800 degrees C for 24 h) on the diffusion of these two sorbates on UL-ZSM-5 materials was also evaluated.  相似文献   

15.
以磷酸、拟薄水铝石和硅溶胶为原料,三乙胺为模板剂,在不同晶化温度和晶化时间的实验条件下,分别采用水热合成法和气相转移法合成了一系列ZSM-5/SAPO-5核壳结构复合分子筛,并用X射线衍射、扫描电镜、X射线能量散射谱、红外光谱和N2吸附等手段对其进行了表征.结果表明,所合成的分子筛是以ZSM-5为核,以SAPO-5为壳的双结构复合分子筛.晶化温度的提高和晶化时间的延长有利于分子筛结晶度的提高.与水热合成法相比,采用气相转移法可以减小壳层SAPO-5的颗粒尺寸,减少脱离ZSM-5表面独立生长的SAPO-5的量,改善SAPO-5在ZSM-5表面的分布.重油裂化结果表明,核壳结构复合分子筛对生成低碳烯烃的催化性能优于机械混合的样品.  相似文献   

16.
In the present work, binary adsorption of p-xylene and toluene in completely siliceous zeolite ZSM-5 was examined by FT-Raman spectroscopy in combination with powder X-ray diffraction. The results indicate that at total loadings of < or = 4 molecules per unit cell (u.c.) both p-xylene and toluene molecules prefer to reside at the intersections of straight and zigzag channels. The structure of the sorbate/sorbent complexes likely belongs to orthorhombic. At high loadings of 7 and 8 molecules/u.c., the framework of the zeolite transforms to another orthorhombic phase. In this high-loaded phase, toluene molecules are distributed evenly in both the channel intersection and the midsection of straight channel. Although p-xylene has access to both the channel intersection and the zigzag channel, it does show a slight preference for the channel intersection. The adsorptive behavior of these aromatics at intermediate total loadings of 5 and 6 molecules/u.c. is more complicated because the zeolitic framework is a mixture of two different orthorhombic phases.  相似文献   

17.
Studies of the Heterogeneous Catalytical Ring Alkylation of Toluene with Methanol on Modified Zeolites ZSM-5 Various ways for controlling the catalytic activity, the shape selectivity, and the deactivation behaviour of modified zeolites ZSM-5 has been shown by the example of the heterogeneous catalytical conversion of toluene with methanol. The preferred formation of the industrially interesting para-xylene is possible by use of ZSM-5-zeolites composed of large crystals, by dealumination of the external surface after hydrothermal treatment, by poisoning of external active centres after impregnation with inorganic salts as well as by isomorphic incorporation of boron for silicon and/or aluminium in the zeolite framework.  相似文献   

18.
采用包埋法合成ZSM-5/SAPO-5核壳结构复合分子筛,研究了凝胶组成对该材料性能的影响,并利用X射线衍射和扫描电镜等手段对其进行了表征。结果表明,合成的分子筛是以ZSM-5为核,SAPO-5为壳的双结构复合分子筛。通过向凝胶中加入晶种或者调节溶剂性质可以明显改变复合材料的结晶度和颗粒形貌。引入晶种合成材料的颗粒形貌以椭圆型为主,分子筛的结晶度增加;以醇和水混合物为溶剂合成分子筛的颗粒仍以球形为主,分子筛的结晶速率降低,结晶度的最高值降低。  相似文献   

19.
预先负载原料法合成ZSM-5/SAPO-5复合分子筛   总被引:1,自引:0,他引:1  
采用预先负载原料法合成了一系列ZSM-5/SAPO-5(核/壳)双结构分子筛, 研究了预负载磷酸的条件对核壳结构分子筛的形成及性质的影响, 采用X射线衍射、扫描电子显微镜、X射线能量散射谱和红外光谱等手段对样品进行了表征. 结果表明, 负载原料的预处理条件明显影响磷与ZSM-5间的作用力及复合分子筛的结晶度和颗粒形貌等特性. 与常规合成方法相比, 在适宜的条件下采用这种方法更有利于小颗粒SAPO-5分子筛的形成及其在ZSM-5表面的生长.  相似文献   

20.
The dynamics of the retained species on ZSM-5 and SAPO-18 catalysts are studied by using a combination of temperature-programmed desorption/oxidation, ex situ analysis, and in situ FTIR spectroscopic measurements over the entire conversion range, using fixed-bed and spectroscopic cell reactors, in continuous and discontinuous mode. The results point to the appropriateness of the combined methodologies to track the interconversion of active into deactivating species. A statistically relevant (supported by linear regression and multivariate analysis) association of the observations is found by using the different complementary methodologies. The kinetics of this interconversion depends on the initial conversion (tuned by acidity and space time) and microporous topology, and involve: (i) in the ZSM-5 catalysts, the diffusion of monocyclic aromatics toward the exterior of the zeolite to form coke, and (ii) in the SAPO-18 catalysts, the obstruction of the cavities by aromatics that grow into tetracyclic aromatic islands.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号