Radiological characterization of commercially available “radon spa sources”

Nowadays, artificial “radon spa sources” for home baths are commercially available. Although these sources could give a potential radiation exposure to the users, few studies have been reported on their radiological measurements. In the present study, five types of radon spa sources were collected and their radiological characterization was investigated. The followings were estimated for these samples: (1) radon emanation coefficients (dry and water-saturated conditions), (2) surface γ-ray dose rate, (3) surface count rates for α- and β-rays, (4) activity concentrations of ²²⁶Ra, ²³²Th and ⁴⁰K, and (5) concentrations of radon and thoron generated from the sources located in an air flow system. The activity concentrations were very high (except for one sample (named “sample B”), although radon emanation coefficient was low compared with soil. This leads to high concentrations of radon/thoron generated from the sample. The maximum surface γ-ray dose rate was observed for sample A (2.7 μGy h⁻¹). If people stay very close to the sample for a long time, the exposure might be significant.     

Synthesis,spectroscopic and crystal structure analysis of 2-(4-fluorobenzyl)-6-(4-methoxyphenyl)imidazo[2,1-b][1,3,4]thiadiazole and its morpholinomethyl derivative

The preparation of 2-(4-fluorobenzyl)-6-(4-methoxyphenyl)-5-morpholin-1-ylmethyl imidazo[2,1-b][1,3,4]thiadiazole via the intermediate 2-(4-fluorobenzyl)-6-(4-methoxyphenyl)Imidazo[2,1-b][1,3,4] thiadiazole is described. Elemental analysis, IR spectrum, ¹H NMR and X-ray crystal structure analyses were carried out to determine the compositions and molecular structures of the two compounds. The crystal packing exhibits intermolecular C–H?O, C–H?N, C–H?F and π–π stacking interactions leading to the formation of the supramolecular network.     

The elemental and isotopic determination of lithium by the coincidence measurement of complementary particles

The coincident measurement of both nuclear products at their complementary angles was used to determine⁶Li by the reactions⁶Li(d, α)⁴He and⁶Li(p, α)³He, and⁷Li by the reaction⁷Li(p, α)⁴He. Elemental lithium was determined in natural samples or samples of known isotopic composition. Isotopic analyses could be carried out over the entire range from 0 to 100 atom% with a relative standard deviation of about 4%. The CMCP technique is highly specific and effectively eliminates interference and background.     

Metal concentrations in Japanese medaka,mosquitofish and insect larvae living in uncontaminated rivers in Kumamoto,Japan

Elemental concentrations in Japanese medaka and mosquitofish collected from uncontaminated rivers in Kumamoto, Japan were analyzed by instrumental neutron activation analysis with k ₀ standardization method to know the background levels. A statistical analysis indicated the difference in metal concentrations among rivers and species. Background levels of elemental concentrations in some aquatic insect larvae were analyzed and metal concentrations were different among species, though they were collected at the same point. Enrichment factors of heavy metals in insect larvae were in the order of 10³−10⁴ suggesting effectiveness of insect larvae as bioindicator.     

Fluorescent detection of peptides and amino acids for capillary electrophoresis via on-line derivatization with 4-fluoro-7-nitro-2,1,3-benzoxadiazole

An in-capillary derivatization of amino acids and peptides with 4-fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) was developed for their subsequent capillary electrophoretic analysis with laser-induced fluorescence detection (λ _ex=488 nm). The in-capillary derivatization was achieved in zone-passing mode by introducing successive plugs of sample and NBD-F into a fused silica capillary previously equilibrated with an alkaline borate buffer. To prevent NBD-F hydrolysis and to achieve a reliable derivatization, NBD-F was prepared daily in absolute ethanol and a plug of absolute ethanol was introduced between the sample and NBD-F reagent plugs. Various parameters influencing the derivatization efficiency were investigated and the optimum conditions were as follows: background electrolyte (BGE), 20 mM borate buffer (pH 8.8); introduction time, 4 s for sample and 2 s for NBD-F; molar ratio of NBD-F/sample, above 215; temperature, 45 °C for amino acids and 35 °C for peptides; applied voltage, +15 kV. The validation of the in-capillary derivatization method under optimal conditions showed a good linearity between the heights of the derivative peaks and the concentrations of the amino acids. The intra-day relative standard deviations of the migration times and the peak heights were less than 1.3% and 4.6%, respectively. The efficient derivatization and separation of a mixture of valine, alanine, glutamic acid and aspartic acid were achieved using this technique. Peptides such as buccaline and β-protein fragment 1–42 could also be derivatized using the developed in-capillary derivatization procedure. In‑capillary derivatization and separation of amino acids with different concentrations. From the top to bottom the concentrations are 1.11×10⁻⁵ M, 5.55×10⁻⁶ M, 2.78×10⁻⁶ M, 6.95×10⁻⁷ M. for valine; 1.26×10⁻⁵ M, 6.30×10⁻⁶ M, 3.15×10⁻⁶ M, 7.88×10⁻⁷ M for alanine; 3.78×10⁻⁵ M, 1.89×10⁻⁵ M, 9.45×10⁻⁶ M, 2.36×10⁻⁶ M for glutamic acid;, 4.27×10⁻⁵ M, 2.14×10⁻⁵ M, 1.07×10⁻⁵ M, 2.68×10⁻⁶ M for aspartic acid. Experiment conditions: injection order: 4s for sample, 1s for absolute ethanol, and then 2s for 5.24×10⁻² M NBD‑F; BGE: 20 mM borate pH 8.77; Applied voltage: 15 kV.     

Determination of trace elements in human liver biopsy samples by ICP–MS and TXRF: hepatic steatosis and nickel accumulation

Human liver biopsy samples, collected from 52 individuals, were analysed by inductively coupled plasma–mass spectrometry (ICP–MS) and total reflection X-ray fluorescence (TXRF) spectrometry in a retrospective study (i.e. patient selection and liver biopsy were not for the purpose of element analysis). The freeze-dried samples (typically 0.5–2 mg dry weight) were digested in a laboratory microwave digestion system and solutions with a final volume of 1 mL were prepared. The concentrations of Cr, Mn, Fe, Ni, Cu, Zn, Rb, and Pb were determined by use of a Thermo Elemental X7 ICP–MS spectrometer. TXRF measurements were performed with an Atomika Extra IIA spectrometer. Yttrium was employed as an internal standard, prepared by dissolution of 5N-purity yttria (Y₂O₃) in our laboratory. The accuracy was tested by analysis of NIST 1577a Bovine Liver certified reference material. The concentrations of Fe, Cu, Zn, and Rb determined in human liver biopsy samples were in good agreement with data published by other authors. The distribution of nickel in the samples was surprisingly uneven—nickel concentrations ranged from 0.7 to 12 μg g⁻¹ (dry weight) in 38 samples and in several samples were extremely high, 36–693 μg g⁻¹. Analysis of replicate procedural blanks and control measurements were performed to prevent misinterpretation of the data. For patients with steatosis (n=14) Ni concentrations were consistently high except for two who had levels close to those measured for the normal group. As far as we are aware no previous literature data are available on the association of steatosis with high concentration of nickel in human liver biopsies taken from living patients. This paper was presented in part at the 2005 European Winter Conference on Plasma Spectrochemistry Budapest, Hungary.     

Quantitative WDXS Microanalysis of Bismuth-Based BaBi4Ti4O15 Perovskites Doped with Nb and Fe

 Quantitative electron-probe microanalysis was used to determine the chemical composition of an Fe- and Nb-doped bismuth-based BaBi₄Ti₄O₁₅ perovskite compound. Elemental concentrations of Fe, Nb, Bi, Ba and Ti were accurately measured using wavelength-dispersive X-ray spectroscopy that was optimised for the analysis of a complex oxide matrix containing minor concentrations of dopants. Measurements were performed with a JEOL JXA 840A electron probe microanalyser at 20 and 26 kV, 50 nA beam current, 100 s maximum counting time and 0.3% preset counting deviation (σ_c) using both PET and LiF crystals. K-ratios were quantified by the ZAF and the φ(ρz) PAP matrix-correction procedures. The results showed that dopants incorporate into the BaBi₄Ti₄O₁₅ at Ti^4 + sites according to the Ba_1−4XBi_4 + 4XTi_4−4XFe_4XO₁₅ and Ba_1 + 4XBi_4−4XTi_4−4XNb_4XO₁₅ solid-solution formulae. The majority of the excess charge introduced by the substitution of Ti^4 + with Fe^3 + or Nb^5 + is compensated for the change in the Ba^2 +/Bi^3 + ratio.     

Single-particle characterization of “Asian Dust” certified reference materials using low-Z particle electron probe X-ray microanalysis

In order to clearly elucidate whether Asian Dust particles experience chemical modification during long-range transport, it is necessary to characterize soil particles where Asian Dust particles originate. If chemical compositions of source soil particles are well characterized, then chemical compositions of Asian Dust particles collected outside source regions can be compared with those of source soil particles in order to find out the occurrence of chemical modification. Asian Dust particles are chemically and morphologically heterogeneous, and thus the average composition and the average aerodynamic diameter (obtainable by bulk analysis) are not much relevant if the chemical modifications of the particles must be followed. The major elemental composition and abundance of the particle types that are potential subjects of chemical modification can only be obtained using single-particle analysis. A single particle analytical technique, named low-Z particle electron probe X-ray microanalysis (low-Z particle EPMA), was applied to characterize two certified reference materials (CRMs) for Asian Dust particles, which were collected from a loess plateau area and a desert of China. The CRMs were defined by bulk analyses to provide certified concentrations for 13 chemical elements. Using the low-Z particle EPMA technique, the concentrations of major chemical species such as aluminosilicates, SiO₂, CaCO₃, and carbonaceous species were obtained. Elemental concentrations obtained by the low-Z particle EPMA are close to the certified values, with considering that the single particle and bulk analyses employ very different approaches. There are still some discrepancies between those concentration values, resulting from analyses of particles with different sizes, different sample amounts analyzed, and uncertainties involved in the single particle analysis.     

Formation of new monomeric Pd(III) complex species with 8-aminoquinoline

By means of EPR and magnetochemical methods the formation of 3 new Pd(III) complex species is proved resulting from the reaction of PdCl₄ ²⁻ and 8-aminoquinoline (8-AQ) in basic (aqueous or aqueous-methanolic) medium. Elemental analysis, visible and IR data for the complexes are also obtained.     

Regional distributions of manganese,iron, copper,and zinc in the brains of 6-hydroxydopamine-induced parkinsonian rats

Time courses of changes in manganese, iron, copper, and zinc concentrations were examined in regions of the brain of a 6-hydroxydopamine (6-OHDA)-induced rat model of Parkinson’s disease using inductively coupled plasma mass spectrometry (ICP-MS). The concentrations were simultaneously determined in brain section at the level of the substantia nigra 1, 3, 7, 10, 14, and 21 days after the 6-OHDA treatment and compared with those of control rats. The distributions of these elements were obtained for 18 regions of the sagittal section (1-mm thick). The ICP-MS results indicated that Mn, Fe, Cu, and Zn levels of the 6-OHDA-induced parkinsonian brain were observed to increase in all regions that lay along the dopaminergic pathway. In the substantia nigra, the increase in Mn level occurred rapidly from 3 to 7 days and preceded those in the other elements, reaching a plateau in the 6-OHDA brain. Iron and Zn levels increased gradually until 7 days and then increased rapidly from 7 to 10 days. The increase in the copper level was slightly delayed. In other regions, such as the globus pallidus, putamen, and amygdala, the levels of Mn, Fe, Cu, and Zn increased with time after 6-OHDA treatment, although the time courses of their changes were region-specific. These findings contribute to our understanding of the roles of Mn and Fe in the induction of neurological symptoms and progressive loss of dopaminergic neurons in the development of Parkinson’s disease. Manganese may hold the key to disturbing cellular Fe homeostasis and accelerating Fe levels, which play the most important role in the development of Parkinson’s disease.     

A low-cost system for rapid automatic neutron activation analysis at small research reactors

A system for rapid automatic neutron activation analysis is governed by software performing irradiation control, neutron flux monitoring and gamma-spectrometry with real-time correction of counting losses as well as spectra evaluation, nuclide identification and calculation of concentrations in a fully automatic flow of operations.^1,2 Elemental concentrations are derived from a list of experimentally determined specific saturation activities. To expand this list, the “k0_IAEA” software³ is presently under evaluation and will be reported on in this paper. At a Triga reactor, reactor pulse activation may enhance the sensitivity for very short half-lives,⁴ and will be presented in our paper.     

New Methacrylate Copolymers Based on the Benzofurane Ring: Synthesis,Characterization, Monomer Reactivity Ratios and Biological Activity

The free radical copolymerization of (5-bromo-1-Benzofuran-2-yl)(phenyl)-O-methacrylketoxime (BPMKO) with 2-(4-acetylphenoxy)-2-oxoethyl-2-methylacrylate(AOEMA) has been carried out in 1, 4-dioxane at 65°C ± 1 and was analyzed by Fourier transform infrared, ¹H-NMR, ¹³C-NMR and gel permeation chromatography. Elemental analysis was used to determine the molar fractions of BPMKO and AOEMA in the copolymers. The monomer–reactivity ratios were calculated according to the general copolymerization equation using Kelen-Tüdõs and Finemann-Ross linearization methods. The reactivity ratios indicated a tendency toward random copolymerization. The polydispersity indices of the polymers were determined by gel permeation chromatography and suggested a strong tendency for chain termination by disproportionation. The thermal behaviors of copolymers with various compositions were investigated by differential scanning calorimetry and thermogravimetric analysis. The glass-transition temperature of the copolymers increased with increasing BPMKO content in the copolymers. All the products showed moderate activity against different strains of bacteria and fungi.     

Complexation studies of 3-substituted <Emphasis Type="Italic">β</Emphasis>-diketones with selected d- and f-metal ions

Results of spectroscopic investigations related to complex compositions of 3-substituted derivatives of pentane-2,4-dione (β-diketonate) complexes with chosen d- and f-metal ions are presented. Ligands 3-allylacetylacetone (3all-acac) and 3-benzylacetylacetone (3ben-acac) were prepared and used for the complexation study with Cu(II), Co(II), Nd(III), and Ho(III) metal ions. Based on the absorption spectra of lanthanide ions in their hypersensitive transitions, with the use of computer assisted target factor analysis (CAT) and absorption spectra of the ligands with Cu(II) and Co(II), the verification of complex compositions and the determination of their stability constants were achieved. In case of Nd(III) and Ho(III) complexes with β-diketone ligands, absorption of their maxima were studied in the range of hypersensitive transitions ⁴ I _9/2 → ⁴ F _7/2 + ⁴ S _3/2 (λ _max ∼ 734 nm and 748 nm) for Nd(III) and in the range of 435–465 nm, corresponding to the hypersensitive transition ⁵ G ₆ → ⁵ I ₈ (λ _max ∼ 450 nm), for Ho(III).     

Mineral composition of frozen taro for determination of geographic origin

The mineral composition of frozen food of taro [Colocasia esculenta (L.) Schott] was analyzed to categorize the geographical production place of taro. The concentrations of Co and H₂PO₄ ⁻ were found to be useful to separate the producing place between Japan and China. The analysis was performed by instrumental neutron activation analysis (INAA) and ion chromatography (IC). In the case of INAA, the samples were dried and sealed in a vinyl bag and irradiated with thermal neutrons from JRR3M, installed at Japan Atomic Energy Agency (JAEA). The activated samples were cooled down for a few weeks and the elements (Co, Cr, Fe, Rb, Zn) were determined. Cobalt concentration of frozen taro from China was higher than that from Japan. The tendency was the same in the fresh sample of taro. When concentration of H₂PO₄ ⁻ of frozen sample was measured, taro from Japanese product was higher than that of Chinese one, contrary to fresh sample. This result might be caused by the leakage of H₂PO₄ ⁻ during freezing process, indicating that we should be careful to apply the discrimination indicators. In addition to Co, there was a significant difference of Rb and Fe concentrations between frozen taro from Japan and China.     

Classifying wine according to geographical origin via quadrupole-based ICP–mass spectrometry measurements of boron isotope ratios

The potential of quadrupole-based ICP–MS as a tool for B-isotopic analysis of wines and its usefulness in provenance determinations were assessed. A precision of 0.1–0.25% RSD (corresponding to a relative standard deviation of the mean of three replicate measurements of 0.06–0.12%) was sufficient to establish small differences in the B isotope ratios in wines from different geographical origins. Each sample measurement was bracketed by measurements of a standard and mass bias drift correction made by interpolation. Sample preparation was kept to a minimum to avoid possible fractionation. Dilution of the wine samples by a factor of 100 with 0.65% HNO₃ was found to reduce matrix-induced mass discrimination substantially. Wines from three wine-producing regions, Stellenbosch, Robertson, and Swartland, in the Western Cape Province of South Africa, and wines from specific regions in France (Bergerac) and Italy (Valpolicella) were analyzed by ICP–QMS for their B-isotopic compositions. It was concluded that the ¹¹B/¹⁰B ratios can be used to characterize wines from different geographical origins. Average ¹¹B/¹⁰B ratios in red wines from South Africa (Stellenbosch), France (Bergerac), and Italy (Valpolicella) were found to differ by between 0.5 and 1.5%.     

Matrix solid-phase dispersion followed by gas chromatography-mass spectrometry for the determination of triclosan and methyl triclosan in sludge and sediments

An expeditious method for the determination of triclosan (TCS) and methyl triclosan (MTCS) in sludge and sediment samples is presented. Extraction and cleanup steps were integrated in the same process using matrix solid-phase dispersion as sample preparation technique. Effects of different variables on the efficiency and the selectivity of the sample preparation process are discussed. Under final working conditions, samples (0.5 g) were dispersed with diatomaceous earth (1 g) and transferred to a polypropylene syringe containing 2 g of silica impregnated with sulphuric acid (15%, w:w). Analytes were recovered with 10 mL of dichloromethane. After solvent exchange to ethyl acetate, TCS was converted into the tert-butyldimethylsilyl derivative, and the extract was analysed by gas chromatography-mass spectrometry, without any additional cleanup. Obtained recoveries, for sludge and sediment samples spiked at different concentration levels, ranged from 86% to 113%, with associated standard deviations between 2 and 13%. Limits of quantification of the global method were 6 and 7 ng g⁻¹ for MTCS and TCS, respectively. Both compounds were detected in all the processed sludge samples with maximum concentrations of 191 ng g⁻¹ (MTCS) and 2,640 ng g⁻¹ (TCS). The parent bactericide was also found in some sediment samples at concentrations up to 200 ng g⁻¹.     

Dispersive liquid–liquid microextraction followed by gas chromatography–mass spectrometry for the rapid and sensitive determination of UV filters in environmental water samples

The performance of the dispersive liquid–liquid microextraction (DLLME) technique for the determination of eight UV filters and a structurally related personal care species, benzyl salicylate (BzS), in environmental water samples is evaluated. After extraction, analytes were determined by gas chromatography combined with mass spectrometry detection (GC-MS). Parameters potentially affecting the performance of the sample preparation method (sample pH, ionic strength, type and volume of dispersant and extractant solvents) were systematically investigated using both multi- and univariant optimization strategies. Under final working conditions, analytes were extracted from 10 mL water samples by addition of 1 mL of acetone (dispersant) containing 60 μL of chlorobenzene (extractant), without modifying either the pH or the ionic strength of the sample. Limits of quantification (LOQs) between 2 and 14 ng L⁻¹, inter-day variability (evaluated with relative standard deviations, RSDs) from 9% to 14% and good linearity up to concentrations of 10,000 ng L⁻¹ were obtained. Moreover, the efficiency of the extraction was scarcely affected by the type of water sample. With the only exception of 2-ethylhexyl-p-dimethylaminobenzoate (EHPABA), compounds were found in environmental water samples at concentrations between 6 ± 1 ng L⁻¹ and 26 ± 2 ng mL⁻¹.     

Determination of total iron in fresh waters using flow injection with potassium permanganate chemiluminescence detection

A flow injection method is described for the determination of iron in fresh water based on potassium permanganate chemiluminescence detection via oxidation of formaldehyde in aqueous hydrochloric acid. Total iron concentrations are determined after reducing Fe(III) to Fe(II) using hydroxylamine hydrochloride. The detection limit (three standard deviations of blank) is 1.0 nM, with a sample throughput of 120 h⁻¹. The calibration graph was linear over the range (2–10) × 10⁻⁷ M (r ² = 0.9985) with relative standard deviations (n = 5) in the range 1.0–2.3%. The effect of interfering cations (Ca(II), Mg(II), Zn(II), Ni(II), Co(II), Fe(III), Mn(II), Pb(II), and Cu(II)) and common anions (Cl⁻, SO ₄ ²⁻ , PO ₄ ³⁻ , NO ₃ ⁻ , NO ₂ ⁻ , I⁻, F⁻, and SO ₃ ²⁻ ) was studied at their maximum admissible concentrations in fresh water. The method was applied to fresh-water samples from the Quetta Valley, and the results obtained (0.04 ± 0.001–0.11 ± 0.01 mg/L Fe(II)) were in reasonable agreement with those obtained using the spectrophotometric reference method (0.05 ± 0.01–0.12 ± 0.02 mg/L Fe(II)). The text was submitted by the authors in English.     

Elemental mapping and quantitative analysis of Cu, Zn, and Fe in rat brain sections by laser ablation ICP-MS

This report details the application of laser ablation quadrupole ICP-MS for the (multi)elemental mapping of 100-μm-thick sections of rat brain. The laser spot size used was 60 μm, and the laser scan speed was 120 μm s⁻¹. The analysis was relatively rapid, allowing mapping of a whole brain thin section (≈1 cm²) in about 2 h. Furthermore, the method was amenable to multi-element data collection including the physiologically important elements P and S and afforded sub μg g⁻¹ detection limits for the important trace elements Cu and Zn. Calibrations were performed with pressed pellets of biological certified reference materials, and the elemental distributions and concentrations of Cu, Zn, and Fe were determined in whole rat brain sections. The distributions and concentration ranges for these elements were consistent with previous studies and demonstrate the utility of this technique for rapid mapping of brain thin sections.     

Simultaneous determination of δ15N and δ18O of N2O and δ13C of CH4 in nanomolar quantities from a single water sample

We have developed a rapid, sensitive, and automated analytical system to simultaneously determine the concentrations and stable isotopic compositions (δ¹⁵N, δ¹⁸O, and δ¹³C) of nanomolar quantities of nitrous oxide (N₂O) and methane (CH₄) in water, by combining continuous‐flow isotope‐ratio mass spectrometry and a helium‐sparging system to extract and purify the dissolved gases. Our system, which is composed of cold traps and a capillary gas chromatograph that use ultra‐pure helium as the carrier gas, achieves complete extraction of N₂O and CH₄ in a water sample and separation among N₂O, CH₄, and the other component gases. The flow path following exit from the gas chromatograph was periodically changed to pass the gases through the combustion furnace to convert CH₄ and the other hydrocarbons into CO₂, or to bypass the combustion furnace for the direct introduction of eluted N₂O into the mass spectrometer, for determining the stable isotopic compositions through monitoring the ions of m/z 44, 45, and 46 of CO and N₂O⁺. The analytical system can be operated automatically with sequential software programmed on a personal computer. Analytical precisions better than 0.2‰ and 0.3‰ and better than 1.4‰ and 2.6‰ were obtained for the δ¹⁵N and δ¹⁸O of N₂O, respectively, when more than 6.7 nmol and 0.2 nmol of N₂O, respectively, were injected. Simultaneously, analytical precisions better than 0.07‰ and 2.1‰ were obtained for the δ¹³C of CH₄ when more than 5.5 nmol and 0.02 nmol of CH₄, respectively, were injected. In this manner, we can simultaneously determine stable isotopic compositions of a 120 mL water sample with concentrations as low as 1.7 nmol/kg for N₂O and 0.2 nmol/kg for CH₄. Copyright © 2010 John Wiley & Sons, Ltd.