GaN基白光LED的结温测量

用正向电压法、管脚法和蓝白比法等三种方法测量GaN基白光LED的结温,获得了较为准确的结温,误差可以控制在4℃以内.正向电压法在恒定电流的条件下,得到了正向电压与结温的线性关系;蓝白比法在不同环境温度和不同注入电流两种情况下,都得到了蓝白比与结温较好的线性关系.提出了蓝白比法可能的物理机制,提高环境温度和增大注入电流都会使结温升高,蓝光峰值波长也会改变,这两个因素都会影响荧光粉的激发和发光效率.降低结温需要考虑的主要因素有白光LED的接触电阻、串联电阻和外量子效率,封装材料的热导率,反射杯和管脚的设计,以及空气散热部分的散热面积等.     

LED结温与光谱特性关系的测量

采用恒定驱动电流改变环境温度和恒定环境温度改变驱动电流两种方法分别对直径5 mm封装的AlGaInP型红光和黄光LED,InGaN型绿光和蓝光LED,以及InGaN蓝光+荧光粉的白光LED的结温与其光谱特性进行了测量,得到了不同条件下LED结温与光谱特性的关系.结果表明;AlGaInP LED的峰值波长与结温有良好线性关系,InGaN LED的峰值波长则与结温没有明显对应关系;但白光LED发射光谱的白、蓝功率比与结温有良好线性关系;对AlGaInP LED及蓝光激发的白光LED,通过光谱特性测量可快速、准确地确定光源系统中各LED的结温继而预测光源系统的有效寿命.     

LED结温与光谱特性关系的测量

采用恒定驱动电流改变环境温度和恒定环境温度改变驱动电流两种方法分别对直径5 mm封装的AlGaInP型红光和黄光LED,InGaN型绿光和蓝光LED,以及InGaN蓝光+荧光粉的白光LED的结温与其光谱特性进行了测量,得到了不同条件下LED结温与光谱特性的关系.结果表明;AlGaInP LED的峰值波长与结温有良好线性关系,InGaN LED的峰值波长则与结温没有明显对应关系;但白光LED发射光谱的白、蓝功率比与结温有良好线性关系;对AlGaInP LED及蓝光激发的白光LED,通过光谱特性测量可快速、准确地确定光源系统中各LED的结温继而预测光源系统的有效寿命.     

基于特征光谱参量表征发光二极管结温的方法

针对采用蓝光激发荧光粉产生白光的YAG型白光LED,通过分析其光谱波谷特性,采用常规可见光光谱仪和温控系统设计了一套基于光谱特征参量的LED结温测试系统.测量方法分为定标函数的测定和任意状态下的测量两部分.首先采用光谱仪测量在给定的多个不同结温和正常驱动电流下的相对发光光谱数据,再分析其光谱波谷处的相对光谱强度.从实用性和降低成本的角度考虑,采用正常工作电流驱动,但以正常工作电流驱动下的LED在光谱仪的固定反应时间内其自加热效应不可忽略.因此采用选定基准状态法,将各温度下的相对发光光谱强度与基准状态下的逐点作差得到相应的发光光谱强度差,同时为了减少温控系统引入的温度偏差,同样将各温度与基准温度作差得到相应的结温差.实验表明高低色温大功率LED的结温差和发光光谱强度差经过一定的函数拟合形成的定标函数其线性度都较高,R2达到0.99以上;利用定标函数,可以测量出在任意状态下的LED结温.最后将采用本方法得出的高低色温LED在不同条件下的结温数据与通过Mentor Graphics公司的T3Ster仪器的测量结果进行了比较,最大偏离度为2.82%,在可接受的误差范围内,表明此方法完全具备可行性,具有一定的实用价值.     

Si衬底GaN基LED的结温特性

结温是发光二极管的重要参数之一,它对器件的内量子效率、输出功率、可靠性及LED的其他一些性能有很大的影响。首次报道Si衬底GaN基LED的结温特性。利用正向压降法测量Si衬底上GaN基LED的结温,通过与蓝宝石衬底上GaNLED的结温比较,发现Si衬底GaNLED有更低的结温,原因归结为Si有更好的导热性。同时也表明:用Si作GaNLED的衬底在大功率LED方面具有更大的应用潜力。     

基于相对光谱强度的非接触式LED结温测量法

基于一体化封装高导热铝板,利用蓝光芯片及常用YAG荧光粉,制备了大功率白光LED,并研究了其在不同结温下的光谱变化规律。发现白光LED辐射光谱在波长485 nm处辐射强度具有极小值,并且此波长的辐射强度与LED结温存在良好的线性关系,以此为依据给出了该波长辐射强度与结温的关系公式,测量了LED结温,并与正向压降法及光谱法的测量结果进行对比。实验结果显示：所提出的结温测量方法与正向压降法测量结果差距不超过2 ℃,该方法保持了正向压降法的结温测量较为准确的优点,克服了光谱法的光谱漂移过小,对测试结果带来较大误差的缺点,同样也具有光谱法的实用性强、高效直观、非接触测量、不破坏灯具结构的优点。     

大功率GaN基发光二极管等效串联电阻的功率耗散及其对发光效率的影响

由于自加热效应的存在，大功率GaN基发光二极管(LED)的芯片温度有可能高出环境温度很多，实验中，芯片温度超出环境高达147 K.从实验测量的大功率LED电流电压特性曲线中，将p-n结和等效串联电阻上的电压降落分离出来，得到了大功率LED等效串联电阻随芯片温度的变化情况.在输入电功率自加热效应的影响下，大功率GaN基LED等效串联电阻呈现出剧烈的变化，其阻值由低输入功率时的1.2 Ω降低到0.9 Ω,然后再升高到1.9 Ω，等效串联电阻的功率耗散在输入功率中所占的比例也随着输入功率的增加迅速增加，最高时接     

结温对高压白光LED光谱特性的影响

高压LED因其自身突出的特点在照明领域有着潜在的应用优势,但作为一种新型功率LED,其光电热特性仍需深入研究。该实验对6和9V GaN基高压LED芯片进行了相同结构和工艺条件的封装,对封装样品进行了10~70℃的变温度光谱测试,并进行了从控温平台温度到器件结温的转换。为保证器件的电流密度相同,6和9V样品光谱测试的工作电流分别设定为150和100mA。结果显示,结温升高会导致蓝光峰值波长红移、波长半高宽增大、光效下降和显色指数上升等现象。在相同平台温度和注入功率下,9V样品的结温低于6V样品;随着温度的升高,9V样品波长半高宽的增加量比6V样品少1.3nm,光效下降量少1.13lm·W~(-1),显色指数上升量少0.28。以上表明,与低压LED相比,高压LED有着更低的工作结温和更小的温度影响。原因在于,相同环境温度下高压LED具有更好的电流扩展性和更少的发热量。此特性在高压LED的研究、发展与应用等方面具有参考价值。此外,峰值波长仍与结温有着较好的线性度,在光谱设备精度较高的情况下可继续作为结温的敏感参数。     

InGaN基白光LED光谱特征和结温相关性研究

 以InGaN蓝光+荧光粉的白光LED为研究对象,在恒定环境温度下改变驱动电流,利用光谱仪测得不同LED结温下的光谱曲线。通过分析实验数据,得出光谱特征与该型LED结温的关系。结果表明：InGaN基白光LED蓝光和荧光的峰值波长与结温没有明显的线性关系;蓝光的光谱线宽以及荧光和蓝光峰值强度的比值与结温具有良好的线性关系。     

大功率GaN基发光二极管等效串联电阻的功率耗散及其对发光效率的影响

由于自加热效应的存在,大功率GaN基发光二极管(LED)的芯片温度有可能高出环境温度很多,实验中,芯片温度超出环境高达147 K.从实验测量的大功率LED电流电压特性曲线中,将p-n结和等效串联电阻上的电压降落分离出来,得到了大功率LED等效串联电阻随芯片温度的变化情况.在输入电功率自加热效应的影响下,大功率GaN基LED等效串联电阻呈现出剧烈的变化,其阻值由低输入功率时的1.2 Ω降低到0.9 Ω,然后再升高到1.9 Ω,等效串联电阻的功率耗散在输入功率中所占的比例也随着输入功率的增加迅速增加,最高时接 关键词： 自加热 等效串联电阻 发光二极管 流明效率     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.