Gas chromatography–mass spectrometry analysis of pheomelanin degradation products

Melanoma is most rapidly increasing in the white population and people with pheomelanin skin type are at high risk to develop melanoma. However, little is known about the pheomelanin structure and function, and further elucidation of this melanin is therefore an important task. A GC/MS method was developed based on hydriodic acid hydrolysis of pheomelanin in the urine. Derivatization was performed with ethyl chloroformate and ethanol:pyridine (4:1, v/v). N,O-Ethoxycarbonyl-ethyl esters were extracted with chloroform and analyzed by GC/MS. 4-Amino-3-hydroxyphenylalanine and 3-amino-4-hydroxyphenylalanine together with one benzothiazinone and two benzothiazole compounds were detected and identified in hydrolyzed samples of synthetic pheomelanin and melanin from the urine of a patient with melanoma. These findings strongly suggest that heterocyclic pheomelanin-type units are incorporated in the pigment structures.     

Comparison of liquid chromatography-microchip/mass spectrometry to conventional liquid chromatography–mass spectrometry for the analysis of steroids

The feasibility of a microfluidic-based liquid chromatography-electrospray ionization/mass spectrometric system (HPLC-Chip/ESI/MS) was studied and compared to a conventional narrow-bore liquid chromatography-electrospray ionization/mass spectrometric (LC-ESI/MS) system for the analysis of steroids. The limits of detection (LODs) for oxime derivatized steroids, expressed as concentrations, were slightly higher with the HPLC-Chip/MS system (50–300 pM) using an injection volume of 0.5 μL than with the conventional LC-ESI/MS (10–150 pM) using an injection volume of 40 μL. However, when the LODs are expressed as injected amounts, the sensitivity of the HPLC-Chip/MS system was about 50 times higher than with the conventional LC-ESI/MS system. The results indicate that the use of HPLC-Chip/MS system is clearly advantageous only in the analysis of low-volume samples. Both methods showed good linearity and good quantitative and chromatographic repeatability. In addition to the instrument comparisons with oxime derivatized steroids, the feasibility of the HPLC-Chip/MS system in the analysis of non-derivatized and oxime derivatized steroids was compared. The HPLC-Chip/MS method developed for non-derivatized steroids was also applied to the quantitative analysis of 15 mouse plasma samples.     

Comparison of supercritical fluid chromatography–tandem mass spectrometry and liquid chromatography–tandem mass spectrometry for the stereoselective analysis of chlorfenvinphos and dimethylvinphos in tobacco

This study used reversed-phase liquid chromatography–tandem mass spectrometry and supercritical fluid chromatography–tandem mass spectrometry for determination of the stereoisomers of chlorfenvinphos and dimethylvinphos in tobacco. Tobacco samples were extracted and purified with a modified quick, easy, cheap, effective, rugged, and safe technique using spherical carbon. The performance of both methodologies was comprehensively compared in terms of methods validation parameters (separation efficiency, linearity, selectivity, recovery, repeatability, sensitivity, matrix effect, etc.). Under optimized conditions, the calibration curves of the stereoisomers of chlorfenvinphos and dimethylvinphos in the range of 10–500 ng/mL showed excellent linearity with R² ≥ 0.997 in both methods. The adequate recoveries of analytes from three different spiked tobaccos were obtained using reversed-phase liquid chromatography–tandem mass spectrometry (86.1–95.7%) as well as supercritical fluid chromatography–tandem mass spectrometry (86.5–94.0%). The relative standard deviations for spiked samples were all below 7.0%. Compared with supercritical fluid chromatography–tandem mass spectrometry, lower matrix effects and LODs can be obtained in reversed-phase liquid chromatography–tandem mass spectrometry.     

Analytical performance of three commonly used extraction methods for the gas chromatography–mass spectrometry analysis of wine volatile compounds

The analytical performance of three extraction procedures based on cold liquid–liquid extraction using dicloromethane (LLE), solid phase extraction (SPE) using a styrene–divinylbenzene copolymer and headspace solid phase microextraction (SPME) using a carboxen–polydimethylsiloxane coated fibre has been evaluated based on the analysis of 30 representative wine volatile compounds. From the comparison of the three procedures, LLE and SPE showed very good linearity covering a wide range of concentrations of wine volatile compounds, low detection limits, high recovery for most of the volatile compounds under study and higher sensitivity compared to the headspace-SPME procedure. The latter showed in general, poor recovery for polar volatile compounds. Despite some drawbacks associated with the LLE and SPE procedures such as the more tedious sampling treatment and the use of organic solvents, the analytical performance of both procedures showed that they are more adequate for the analysis of wine volatiles.     

Optimization of antibiotic analysis in water by solid-phase extraction and high performance liquid chromatography–mass spectrometry/mass spectrometry

This paper describes the development of an optimized method based on solid-phase extraction (SPE) followed by liquid chromatography–electrospray ionization tandem mass spectrometry (LC–MS/MS) for the simultaneous analysis of ten antibiotic compounds including tetracyclines, sulfonamides, macrolides and quinolones. LC–MS/MS sensitivity has been optimized by alterations to both LC and MS operations. Of the two high resolution columns tested, Waters Symmetry C₁₈ endcapped and Agilent Zorbax Bonus-RP, the latter was found to show better performance in producing sharp peaks and clear separation for most of the target compounds. Optimization of the MS fragmentation collision and cone energy enhanced the peak areas of the target analytes. The recovery of the target compounds from water samples was most efficient on Waters Oasis HLB SPE cartridge, while methanol was shown to be the most suitable solvent for desorbing the compounds from SPE. In addition, acidification of samples prior to SPE was shown to enhance the recovery of the compounds. To ensure a satisfactory recovery, the flow rate through SPE should be maintained at ≤10 mL min⁻¹. The method was successfully applied to the analysis of antibiotics from environmental water samples, with concentrations being <LOD in tap water, between <LOD to 28 ng L⁻¹ in river water and between <LOD to 230 ng L⁻¹ in sewage effluent.     

Comparison of various hyphenated chromatography — Mass spectrometry methods for the analysis of β-agonists

Summary Different chromatography — mass spectrometry techniques for the analysis of -agonists have been compared.Gas chromatography — mass spectrometry (electron impact) has been used, as also has liquid chromatography coupled to the mass spectrometer by either thermospray or electrospray interfaces. The results obtained by the three method were compared in terms of sensitivity, selectivity, and richness of information provided by the analysis. It was found that using electrospray ionization, very powerful analysis could be achieved with high sensitivity, thus providing significant potential for the analysis of -agonists.     

Multiresidue analysis of pollutants as their trimethylsilyl derivatives,by gas chromatography–mass spectrometry

This paper reports a multiresidue analysis procedure which permits the identification and quantification of sixty-three water-soluble pollutants. Subsequent to their solid-phase extraction (SPE) enrichment, analyses of species have been carried out from one solution, by a single injection, as their trimethylsilyl-oxime ether/ester derivatives, by gas chromatography–mass spectrometry, within 31 min. Based on our optimized extraction, derivatization and mass fragmentation studies separation have been performed in the total ion current mode, identification and quantification of compounds have been carried out on the basis of their selective fragment ions. Including various pharmaceuticals, benzoic acid, its substituted species, different aromatic carboxylic acids, cholic acids, unsaturated and saturated fatty acids, aliphatic dicarboxylic acids, as well as synthetic pollutants of various origins (2,4-di-tert-butylphenol, different phthalates). Standard compounds were added to 500 mL effluent wastewater samples, at three concentrations (1–5 μg/L, 5–10 μg/L and 10–20 μg/L). Recoveries, using the Waters Oasis cartridges performing extractions at pH 2, pH 4 and pH 7 proved to be the optimum at pH 4 (average recoveries (94.5%), except for cholesterol (10%), paracetamol (18%) and 2,5-dihydroxybenzoic acid (25%). Carbamazepine could be recovered at pH 7, only. Responses, obtained with derivatized standards proved to be linear in the range of 4–80 μg/L levels. Limit of quantitation values varied between 0.92 ng/L (4-hydroxyphenylacetic acid) and 600 ng/L (dehydrocholic acid) concentrations. One of the most important messages of this work is the confirmation of the origin of blank values. It was shown that contaminants, mainly 2,4-di-tert-butylphenol, different phthalates and fatty acids, are sourced both from the reagents and mainly from the SPE procedure, independent on the cartridge applied. Reproducibilities, characterized with the relative standard deviations (RSDs) of measurements, varied between 0.71% and 10%, with an average of 4.38% RSD. The practical utility of the method was shown by the identification and quantification of the pollutant contents of Hungarian influent and effluent wastewaters (for six consecutive months and that of the Danube River for 2 months).     

Liquid chromatography — Particle beam mass spectrometry for identification of unknown pollutants in water

Summary Trace enrichment on a precolumn packed with copolymer material, coupled on-line with reversed-phase, column liquid chromatography-particle beammass spectrometry (RPLC-PB-MS) has been used for both target and non-target analysis of water samples. RPLC is carried out on a C-18-bonded silica column using a linear acetonitrile-0.1 M ammonium acetate gradient. Using optimised PB-MS conditions and 100–250 ml water samples, the detection limits for several phenylureas are in the 0.03–0.05 g l^–1 range using the full-scan mode; repeatability is good and the LC-PB-MS system is robust. Several surface and drinking water samples have been analysed and low levels of various environmental contaminants have been identified using electron impact mass spectra. Applying chemical ionisation with methane as reagent gas in both the positive and negative mode in conjunction with PB-MS provides relevant confirmatory information.     

Development of stir-bar sorptive extraction–thermal desorption–gas chromatography–mass spectrometry for the analysis of musks in vegetables and amended soils

The aim of this study was to develop a sensitive and environment-friendly method based on stir-bar sorptive extraction (SBSE) followed by thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS) to determine 8 synthetic musks (musk ambrette, musk ketone, celestolide, tonalide, galaxolide, phantolide, traseolide, and cashmeran) in vegetables (lettuce, carrot, and pepper) and amended soil samples. In a first step sorptive extraction was studied both in the headspace (HSSE) and in the immerse mode (SBSE). The best results were obtained in the immersion mode which was further studied. The influence of the main factors: methanol (20%) and NaCl addition (0%), extraction temperature (40 °C) and time (180 min), extraction solvent volume (9 mL) and stirring rate (600 rpm) on the efficiency of SBSE was evaluated by means of experimental designs. In the case of TD, desorption time (10 min), desorption temperature (300 °C), cryo-focusing temperature (−30 °C), vent flow (75 mL/min) and vent pressure (7.2 psi) were studied using both a fractioned factorial design and a central composite design (CCD). The method was validated in terms of apparent recoveries (AR%), method detection limits (MDLs) and precision at two different concentration levels. Although quantification using instrumental calibration rendered odd results in most of the cases, satisfactory recoveries (74–126%) were obtained in the case of matrix-matched calibration approach for all of the analytes and matrices studied at the two concentration levels evaluated. MDLs in the range of 0.01–0.8 ng/g and 0.01–1.1 ng/g were obtained for vegetables and amended soil samples, respectively. RSD values within 1–23% were obtained for all the analytes and matrices. Finally, the method was applied to the determination of musks in vegetable and amended soil samples.     

Supercritical carbon dioxide extraction and gas chromatography–mass spectrometry analysis of Gymnema sylvestre R.Br. roots

Supercritical fluid extraction (SFE) achieves a wide range of applications since the past decade as a sustainable green technology. The present study investigates the process for producing high yield by supercritical carbon dioxide (Sc-CO₂) extraction form Gymnema sylvestre R.Br. roots. The effect of temperature and pressure on the percentage of accumulative yield is demonstrated. It is found that the highest yield is obtained at the temperature of 60°C and the pressure of 10?MPa. A proper review showed that there is a lack in the study of Sc-CO₂ extraction of this plant especially for optimization of SFE process which makes this study useful and valuable. For more benefit, the extract which achieves highest percentage is subjected to gas chromatography–mass spectrometry to study its chemical composition and detect the active principle compounds which present with high concentration and expected to be responsible of the pharmaceutical properties of the extract.     

Dispersive solid-phase extraction followed by liquid chromatography–tandem mass spectrometry for the multi-residue analysis of pesticides in raw bovine milk

A fast multi-residue method based on dispersive solid-phase extraction (DSPE) followed by liquid chromatography–tandem mass spectrometry was developed for the simultaneous determination of 44 pesticides in raw bovine milk. Raw bovine milk samples did not percolate through SPE cartridges usually applied for pesticide extraction from homogenized pasteurized milk samples. Therefore, a DSPE technique was implemented and validated for the first time in this work. Graphitized non-porous carbon and C18 modified silica materials were tested both in combination with magnesium sulfate and bonded silica with ethylenediamine-N-propyl phase. The efficiency of the DSPE process was studied at several concentration levels obtaining the higher recoveries with C18 material. The method performance was also assessed and the limits of quantification reached the ng g⁻¹ level, complying with the most recent maximum residue levels. The DSPE method was also shown to be suited to both the fatty and skimmed fractions issued from raw milk. Finally, the extraction method was successfully applied to the analysis of raw milk samples collected in 23 farms of dairy cattle from NW Spain (Galicia).     

Multidimensional gas chromatography–mass spectrometry determination of 3-alkyl-2-methoxypyrazines in wine and must. A comparison of solid-phase extraction and headspace solid-phase extraction methods

Two different strategies for the quantitative determination of 3-alkyl-2-methoxypyrazines in wine and must have been developed and validated. Comparison between both the techniques has been presented and the most adequate has been applied to the determination of these compounds in different samples of wine, made from several varieties of grapes, and also in different samples of must made from Cabernet Sauvignon grapes. Both the methods consisted of a dynamic headspace coupled with a solid-phase extraction (HS–SPE) and solid-phase extraction (SPE) directly from the sample, coupled with multidimensional gas chromatography–mass spectrometry system (MDGC–MS). Both of them require resins LiChrolut EN, and analyte elution has been carried out with dichloromethane. The repeatability of both methodologies was evaluated at two concentration levels. The relative standard deviations (RSD%) were acceptable in every case, but smaller when working with HS–SPE. The recoveries obtained for the three analytes with the two methodologies were almost 100%, with the exception of IBMP, which had a recovery of only 70% with HS–SPE. The linearity was satisfactory with both methods for the range of occurrence of methoxypyrazines in wine and must. The limits of detection of the direct SPE technique were much lower than those of HS–SPE in every case. Direct SPE method detection limits ranged from 0.09 to 0.15 ng L⁻¹. The method based on direct SPE was chosen finally because it had better detection limits and was easier and quicker than the HS–SPE-based method. It has been applied to the determination of these components in 36 wine and 17 musts samples. The quantitative results suggest that the Spanish wines show meaningless amounts of these compounds. IBMP has been found just in between 1.9 and 15 ng L⁻¹.     

Stir-bar-sorptive extraction and ultra-high-performance liquid chromatography–tandem mass spectrometry for simultaneous analysis of UV filters and antimicrobial agents in water samples

Stir-bar-sorptive extraction (SBSE) with liquid desorption (LD) and ultra-high-performance liquid chromatography–electrospray ionization triple-quadrupole tandem mass spectrometry (UHPLC–(ESI)MS–MS) were used for analysis of six personal care products in environmental water: four UV filters (2,2-dihydroxy-4-methoxybenzophenone, benzophenone-3, octocrylene, and octyldimethyl-p-aminobenzoic acid) and two antimicrobial agents (triclocarban and triclosan). Experimental conditions that affect SBSE-LD sorption efficiency (extraction time and temperature, sample pH, and ionic strength) and desorption efficiency (solvent, temperature, and time) were optimized. The method proved to be sensitive—a 50-mL sample was used to determine these compounds in environmental waters at trace levels. The detection limits of the analytical method were 2.5 ng L⁻¹ for river water and 5–10 ng L⁻¹ for effluent and influent sewage water. In river waters, benzophenone-3 was found at levels from 6 ng L⁻¹ to 28 ng L⁻¹ and triclosan at levels <LOQ. Benzophenone-3 was found between 75 and 127 ng L⁻¹ in influent sewage, whereas concentrations of benzophenone-3 and triclosan were commonly below 25 ng L⁻¹ in effluent sewage.     

Development of a screening method for the analysis of organic pollutants in water using dual stir bar sorptive extraction-thermal desorption-gas chromatography–mass spectrometry

The development of a method for screening of organic compounds with a wide range of physico-chemical properties in water, based on dual stir bar sorptive extraction coupled with thermal desorption and gas chromatography–mass spectrometry (dual SBSE-TD-GC–MS) is described. The investigated water sample is divided into two aliquots and extracted with stir bar sorptive extraction at two different conditions: using addition of methanol or sodium chloride, respectively. Following extraction, the two stir bars are inserted into the same glass thermal desorption liner and are simultaneously desorbed and analysed by GC–MS. The method optimisation was performed using 45 environmentally harmful substances with different volatilities (boiling point from 193 to 495 °C), polarity (log K_ow from 2.17 to 8.54) and acido-basic properties. The majority of model compounds was selected from the EU list of priority substances in the field of water policy and from the US EPA method 625, respectively. Optimisation was performed for extraction parameters (sample volume, extraction time, stirring rate, addition of modifiers) as well as for the thermal desorption conditions (desorption flow, desorption time, cryofocusing temperature). Performance characteristics (recovery, repeatability, carryover, linearity, limits of detection and quantification) were determined for the optimised method. An example of analysis of a contaminated groundwater sample is presented.     

Supercritical fluid chromatography tandem mass spectrometry employed with evaporation-free liquid–liquid extraction for the rapid analysis of cinnarizine in rat plasma

Cinnarizine is a weak base, which can produce supersaturation and precipitation during gastrointestinal transit, affecting its absorption in vivo. Therefore, it is necessary to investigate whether the oral bioavailability of cinnarizine can be improved after co-administration with precipitation inhibitors or not. In order to evaluate the pharmacokinetic behavior of cinnarizine in rats, a simple, rapid, sensitive, and environmentally friendly supercritical fluid chromatography-tandem mass spectrometric method was established and validated. In this method, flunarizine, a structural analogue of cinnarizine, was selected as the internal standard, and cinnarizine was extracted from rat plasma using evaporation-free liquid–liquid extraction method. The analytes were separated on a Torus 1-AA column (3.0 mm × 100 mm, 1.7 μm) within 2.0 min, using a gradient elution procedure. The transitions of cinnarizine and flunarizine were m/z 369.1 → 167.1 and m/z 405.1 → 203.1, respectively. Cinnarizine showed good linear correlation in the range of 1–500 ng/ml with a lower limit of quantification of 1 ng/ml. The intra- and interday precision and accuracy of all quality control samples were within ±15%. This high-throughput, accurate, sensitive, and reproducible method has been successfully applied to study the effects of the precipitation inhibitor cinnarizine on the pharmacokinetics in rats.     

Simultaneous multi-residue pesticide analysis in soil samples with ultra-high-performance liquid chromatography–tandem mass spectrometry using QuEChERS and pressurised liquid extraction methods

To assess soil contamination, it is important to be able to measure different classes of pesticides simultaneously. For this reason we developed a sensitive ultra-high-performance liquid chromatography–tandem mass spectrometry method for the simultaneous analysis of 25 pesticides in soil samples. Multi-class pesticides (triazines, phenylureas, phenoxy acid pesticides etc.) were analysed using a single mass spectrometry method with a fast polarity switching option, allowing the analysis of 19 compounds in the positive ionisation mode and six compounds in the negative ionisation mode. Extraction of pesticides from soil samples was performed employing a pressurised liquid extraction (PLE) and a quick, easy, cheap, effective, rugged and safe (QuEChERS) procedure, recently developed for the extraction of multi-residue pesticides from food matrices. The extraction efficiency, performance and recoveries of these two procedures were evaluated and compared. In addition, we studied the effect of matrix on signal suppression or enhancement. Isotope-labelled internal standards (ILIS) were used to compensate the suppression or enhancement of signal intensities in the extracted samples. The method was validated using reference soil material (EUROSOIL 7) spiked with 50 μg/kg of each pesticide. The average recovery by PLE varied between 65.1% and 122.2% with RSDs of 1.7–23.4%. QuEChERS provided better recoveries for most of the pesticides, the extraction recovery ranging from 79.4% to 113.3% with RSDs of 1.0–12.2%. Limits of quantification for all target compounds were within a range of 0.1–2.9 µg/kg.     

Comparative study of extraction techniques for determination of garlic flavor components by gas chromatography–mass spectrometry

Several sampling techniques based on steam distillation (SD), simultaneous distillation and solvent extraction (SDE), solid-phase trapping solvent extraction (SPTE), and headspace solid-phase microextraction (HS-SPME) have been compared for the determination of Korean garlic flavor components by gas chromatography–mass spectrometry (GC–MS). Diallyl disulfide (57.88%), allyl sulfide (23.59%), and diallyl trisulfide (11.40%) were found to be the predominant flavor components of garlic samples extracted by SDE whereas these components were at levels of 89.77%, 2.43%, and 3.89% when the same sample was extracted by SD, 97.77%, 0.17%, and 0.10% by SPTE, and 97.85%, 0.01%, and 0.01% by HS-SPME using the 50/30-m divinyl benzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber. Thermal degradation of components such as allyl methyl sulfide, dimethyl disulfide, and thiirane were observed for SDE and SD but not for SPTE or HS-SPME. HS-SPME had several advantages compared with SD, SDE, and SPTE—rapid solvent-free extraction, no apparent thermal degradation, less laborious manipulation, and less sample requirement. Five different fiber coatings were evaluated to select a suitable fiber for HS-SPME of garlic flavor components. DVB/CAR/PDMS was most efficient among the five types of fiber investigated.