Use of SPME extraction to determine organophosphorus pesticides adsorption phenomena in water and soil matrices

Solid-phase micro extraction (SPME) coupled with GC enables rapid and simple analysis of organophosphorus pesticides in a range of complex matrices. Investigations were made into the extraction efficiencies from water of six organophosphorus insecticides (methamidophos, omethoate, dimethoate, parathion methyl, malathion, and parathion ethyl) showing a wide range of polarities. Three SPME fibres coated with different stationary phases, polydimethylsiloxane, polyacrylate, and carbowax-divinylbenzene (CW-DVB), were investigated. Water was spiked with the pesticides at concentrations from 1 to 0.01 µg mL-1, and the solutions used for optimization of the procedure. The CW-DVB fibre, with a 65 µm coating, gave the best performance. The optimized experimental conditions were sample volume 10 mL at 20°C, equilibration time 16 min, pH 5, and presence of 10% w/v NaCl. SPME analyses were performed on solutions obtained by equilibrating aqueous pesticide solutions with six certified soils with various physico-chemical characteristics. SPME data were also assessed by comparison with analyses performed by using conventional solid-phase extraction. Results indicate the suitability of SPME for analysis of pesticides in environmental water samples.     

Development of new solid-phase microextraction fibers by sol-gel technology for the determination of organophosphorus pesticide multiresidues in food

Allyloxy bisbenzo 16-crown-5 trimethoxysilane was first used as precursor to prepare the sol-gel-derived bisbenzo crown ether/hydroxyl-terminated silicone oil (OH-TSO) SPME coating. The coating procedure involving sol solution composition and conditioning process was presented. Compared with commercial SPME stationary phases, the new coatings showed higher extraction efficiency and therefore could provide higher sensitivity for organphosphorous pesticides (OPs). Limits of detection (LODs) were in the range of 0.003-1.0 ng/g for these OPs in food samples (honey, juice, orange and pakchoi). The optimal extraction conditions of the new coatings to OPs in these samples were investigated by adjusting extraction time, salt addition, extraction temperature, and dilution ratios of samples with distilled water by using SPME coupled with gas chromatography (GC)-flame photometric detection (FPD). The method was applied to determine the concentrations of OPs in real samples.     

Analysis of polar pesticides in water and wine samples by automated in-tube solid-phase microextraction coupled with high-performance liquid chromatography-mass spectrometry

A simple and sensitive method for the determination of polar pesticides in water and wine samples was developed by coupling automated in-tube solid-phase microextraction (SPME) to high-performance liquid chromatography-electrospray ionization mass spectrometry (HPLC-ESI-MS). To achieve optimum performance, the conditions for both the in-tube SPME and the ESI-MS detection were investigated. In-tube SPME conditions were optimized by selecting the appropriate extraction parameters, especially the stationary phases used for SPME. For the compounds studied, a custom-made polypyrrole (PPY)-coated capillary showed superior extraction efficiency as compared to several commercial capillaries tested, and therefore, it was selected for in-tube SPME. The influence of the ethanol content on the performance of in-tube SPME was also investigated. It was found that the amount of pesticides extracted decreased with the increase of ethanol content in the solutions. The ESI-MS detection conditions were optimized as follows: nebulizer gas, N2 (30 p.s.i.; 1 p.s.i.=6894.76 Pa); drying gas, N2 (10 l/min, 350 degrees C); capillary voltage, 4500 V; ionization mode, positive; mass scan range, 50-350 amu; fragmentor voltage, variable depending on the ions selected. Due to the high extraction efficiency of the PPY coating and the high sensitive mass detection, the detection limits (S/N = 3) of this method for the compounds studied are in the range of 0.01 to 1.2 ng/ml, which are more than one order of magnitude lower than those of the previous in-tube SPME-HPLC-UV method. A linear relationship was obtained for each analyte in the concentration range of 0.5 to 200 ng/ml with MS detection. This method was applied to the analysis of phenylurea and carbamate pesticides in spiked water and wine samples.     

Simultaneous determination of phenyl- and sulfonyl-urea herbicides in river water at sub-parts-per-billion level by on-line preconcentration and liquid chromatography-tandem mass spectrometry

A method based on solid-phase microextraction and gas chromatography flame photometric detector for the determination of organophosphorus pesticides (OPPs) in food samples was described. Three kinds of vinyl crown ether polar fibers were prepared with sol-gel process and used for the analytes. The new coatings showed higher extraction efficiency and sensitivity for organophosphorus pesticides compared with commercial fibers—85 μm PA and 65 μm PDMS-DVB. Specifically, the benzo-15-crown-5 coating was the most effective for the target analytes. Several factors affecting the performance of SPME such as extraction temperature and time, salt addition, and dilution ratios of samples were optimized. The apparent recoveries of spiked food samples (apple juice, apple and tomato) were determined to be over 55.3% and the limits of detection (LODs) were in the range of 0.003-0.09 ng/g for the OPP studied. The method was applied to determine the concentrations of OPP in real food samples.     

A SDME/GC–MS methodology for determination of organophosphate and pyrethroid pesticides in water

A rapid and simultaneous method for identification and quantification of pesticides residues in water samples have been developed and applied to the analysis of real samples. Tap and San Francisco River water samples were collected from Propria town and Aracaju city in the state of Sergipe, Brazil. A new single-drop microextraction (SDME) followed by gas chromatography–mass spectrometry techniques were used to determine the dimethoate, methyl parathion, ethion (organophosphates) and permethrin (pyrethroid) pesticides in water samples. The parameters linearity, linear range, precision, accuracy, sensitivity and robustness were studied for validation of the SDME/GC–MS method. An important point to this study is that plots of relative response and logarithmic concentrations were used to verify that the measurements were within the linear dynamic range of the method. In order to enhance high linearity of analytical curve, points that do not belong to 95 to 105% of linear range were excluded. Recovery tests of pesticides in different water samples (tap water and river water) were between 76.2 and 107% and this evaluation was used to demonstrate the reliability of the method. For all pesticides the method showed the limits of detection (LOD) in a range between 0.05 and 0.38 μg L^{− 1} and the limit of quantification (LOQ) between 0.15 and 1.1 μg L^{− 1}. All these parameters demonstrate high sensitivity of the developed method and the capability for detecting and quantifying of low levels of pesticides in water samples.     

Analysis of trace levels of pesticides in rainwater using SPME and GC–tandem mass spectrometry

A multiresidue method using gas chromatography coupled to ion trap tandem mass spectrometry (GC–ITD–MS/MS) associated with solid phase microextraction (SPME) was developed for the analysis of 20 pesticides commonly used in the Alsace region in rainwater samples. Since the pesticides were expected to be present at very low concentrations and in complex matrices, the analytical method used was both highly selective and sensitive. Therefore, fibers coated with polyacrylate (PA), polydimethylsiloxane (PDMS) and polydimethylsiloxane-divinylbenzene (PDMS-DVB) were tested, and the parameters affecting the precision and accuracy of the SPME method were investigated and optimized. These parameters include the type of fiber, the adsorption time, the effect of salt, and the extraction temperature. The PDMS fiber was the most polyvalent for the extractions of the different pesticides studied. Detection limits of between 5 and 500 ng L⁻¹, depending on the compounds under study (except for those which could not be analyzed: captan and mevinphos), were obtained with this analytical procedure. This method was applied to the analysis of rainwater samples collected simultaneously on a weekly basis at one rural and one urban site between March 2002 and July 2003. While some of the 20 pesticides analyzed were constantly detected (such as lindane and atrazine), a strong temporal variability was observed for some of the others (including alachlor, metolachlor, atrazine).     

Multi-class pesticide analysis in human hair by gas chromatography tandem (triple quadrupole) mass spectrometry with solid phase microextraction and liquid injection

A method for the simultaneous detection and quantification of 22 pesticides from different chemical classes was developed using solid-phase microextraction (SPME) and gas chromatography tandem (triple quadrupole) mass spectrometry. Pesticides were extracted from 50 mg of pulverized hair with acetonitrile. The extract was submitted to two successive steps of direct immersion-SPME at 30 °C and 90 °C or to a liquid injection without SPME in order to obtain optimized conditions for each of the 22 analytes investigated. Validation parameters were significantly influenced by both the injection mode (SPME vs liquid injection) and the temperature of SPME. Limits of quantification ranged from 0.05 pg mg⁻¹ for trifluralin to 10 pg mg⁻¹ for pentachlorophenol. The application of the validated method to the analysis of samples collected from non-occupationally exposed volunteers demonstrated the presence of pesticides in all the samples tested. Altogether, 13 different analytes were detected at concentration above the limit of quantification.     

Multiple pesticide analysis in wine by MEKC combined with solid-phase microextraction and sample stacking

In this work, a new method for the determination in white wines of 12 pesticides widely used in vine cultivars (namely, carbendazim, pirimicarb, metalaxyl, pyrimethanil, procymidone, nuarimol, azoxystrobin, tebufenozide, fenarimol, benalaxyl, penconazole, and tetradifon) using solid-phase microextraction (SPME) and MEKC with diode-array detection (DAD) was developed. The MEKC buffer consisted of 100 mM sodium tetraborate and 30 mM SDS at pH 8.5 with 6% v/v 1-propanol. Reversed-electrode polarity stacking mode (REPSM) was applied as on-line preconcentration strategy. In order to carry out an effective and sensitive determination of these pesticides in wine samples, an off-line SPME procedure was optimized by means of an experimental design. After studying the extraction performance of different SPME coatings, PDMS/divinylbenzene (PDMS/DVB) fibers were found the most appropriate for the extraction of most of these pesticides. Carbendazim and metalaxyl could not be extracted from wine samples. Calibration curves for extracted standards and fortified white wines were studied in order to determine the presence of a matrix effect. The combination of both preconcentration procedures (SPME and REPSM) allowed the determination of ten of these pesticides in white wines at concentrations between 0.054 and 0.113 mg/L. (i.e., levels well below the maximum residue limits (MRLs) allowed for these compounds in wine grapes). Ten homemade wines were they analyzed with the optimized method demonstrating the usefulness of the proposed procedure.     

Solid-phase microextraction of the antifouling Irgarol 1051 and the fungicides dichlofluanid and 4-chloro-3-methylphenol in water samples.

Three pesticides usually added to paint formulations, Irgarol 1051, dichlofluanid and 4-chloro-3-methylphenol, were determined by solid-phase microextraction (SPME) with 85-micron polyacrylate fibers and gas chromatography-mass spectrometry. The parameters affecting the SPME process (the pH, the addition of salt to the sample, and the time and temperature of the absorption step) were optimized. The method developed was applied to the analysis of water samples from Ebro river, marinas and fishing ports. The method enables these compounds to be detected at concentrations between 0.2 and 3.0 micrograms l-1 under full scan conditions and between 0.05 and 0.08 microgram l-1 under SIM mode.     

Development of a two-dimensional liquid chromatography system with trapping and sample enrichment capabilities

A solid-phase microextraction (SPME) followed by a gas chromatographic-mass spectrometric (GC-MS) determination has been developed and validated for the determination of cyprodinil and fludioxonil in white wine samples. Extraction parameters such as the selection of SPME coating, the effect of the temperature, the effect of the headspace volume and the salt addition were studied and optimized, together with GC-MS analytical conditions. The divinylbenzene-Carboxen-polydimethylsiloxane (DVB-CAR-PDMS) fiber was the most appropriate for the determination of the two pesticides in wine. The quality parameters of the proposed method demonstrated a good precision (RSD about 5%), with detection limits of 0.1 and 0.2 microg/l for cyprodinil and fludioxonil, respectively. Fifteen commercial white wine samples produced in Rías Baixas area in Galicia (N.W. Spain) were analyzed with the SPME-GC-MS procedure. Some of the commercial wines (75%) presented the two pesticides in concentrations ranging from 0.9 to 28.6 microg/l. In conclusion, SPME-GC-MS has a great potential for fungicide determination in wines.     

A high-throughput approach for the determination of pesticide residues in cucumber samples using solid-phase microextraction on 96-well plate

A high-throughput solid-phase microextraction (SPME) on 96-well plate together with gas chromatography–mass spectrometry (GC–MS) was developed for the determination of some selected pesticides in cucumber samples. Pieces with the length of 1.0 cm of silicon tubing were precisely prepared and then coated on the end part of stainless steel wires. The prepared fibers were positioned in a home-made polytetrafluoroethylene (PTFE)-based constructed ninety-six holes block to have the possibility of simultaneous immersion of the SPME fibers into the center of individual wells. Pesticides such as diazinon, penconazol, tebuconazol, bitertanol, malathion, phosalone and chlorpyrifos-methyl were selected for their highly application in cucumber field. The performances of the SPME fibers, such as intra and inter-fibers reproducibility, were evaluated and the results showed a good similarity in extraction yields. A volume of 1 mL of the aquatic supernatant of the cucumber samples was transferred into the 96-well plate and the array of SPME fibers was applied for the extraction of the selected pesticides. The important parameters influencing the whole extraction process including, organic solvent percent, salt addition, dilution factor, stirring rate and extraction time were optimized. The inter- and intra-day RSD% were found to be less than 15.4%. Limits of detection (LOD) and limits of quantification (LOQ) were below 60 and 180 μg kg⁻¹, respectively. The coefficient of determination was satisfactory (r² > 0.99) for all the studied analytes. The developed method was successfully applied to the monitoring of several samples gathered from local markets.     

Validation of a solid-phase microextraction method for the determination of organophosphorus pesticides in fruits and fruit juice

A method for the determination of organophosphorus pesticides (diazinon, fenitrothion, fenthion, quinalphos, triazophos, phosalon and pyrazophos) in fruit (pears) and fruit juice samples was developed and validated. The samples were diluted with water, extracted by solid-phase microextraction (SPME) and analysed by gas chromatography (GC) using a flame photometric detector in phosphorous mode. Limits of detection of the method for fruit and fruit juice matrices were below 2 micrograms/kg for all pesticides. Relative standard deviations for triplicate analyses of samples fortified at 25 micrograms/kg of each pesticide were not higher than 8.7%. Recovery tests were performed for concentrations between 25 and 250 micrograms/kg. Mean recoveries for each pesticide were all above 75.9% and below 102.6% for juice, and between 70 and 99% for fruit except for pyrazophos in the fruit sample (with mean recovery of 53%). Therefore, the proposed method is applicable in the analysis of pesticides in fruit matrices and the use of the method in routine analysis of pesticide residues is discussed.     

Optimization of solid-phase microextraction conditions using a response surface methodology to determine organochlorine pesticides in water by gas chromatography and electron-capture detection.

A response surface methodology was applied to optimise the solid-phase microextraction (SPME) conditions using a polyacrylate-coated fiber to determine thirteen organochlorine pesticides from water. Analyses were performed using gas chromatography-electron-capture detection. Variables affecting absorption in both the headspace and immersion extraction were optimised by using a response surface generated with a Doehlert design, and the results were compared. The immersion SPME method was selected since higher recoveries were obtained for most of the compounds studied. The method developed was applied to the analysis of tap and Ebro river water samples. The linear range of most pesticides for real samples was found to be between 0.001 and 2.5 micrograms l-1 and the limits of detection were between 0.15 and 0.35 ng l-1. The repeatability and the reproducibility between days of the method (n = 6), expressed as relative standard deviation, for tap water spiked at a level of 1 ng l-1 were between 5.7 and 25.6% and between 7.6 and 26.5%, respectively.     

Solid-phase extraction versus solid-phase microextraction for the determination of chlorinated paraffins in water using gas chromatography-negative chemical ionisation mass spectrometry

Solid-phase extraction (SPE) and solid-phase microextraction (SPME) were evaluated for the analysis of short-chain chlorinated paraffins (SCCPs) in water samples using gas chromatography coupled to negative chemical ionisation mass spectrometry (GC-NCI-MS). For SPE optimisation, four commercially available SPE cartridges were tested and several SPE parameters, such as the elution solvent, elution volume and breakthrough volume were studied. The best results were obtained with Varian Bond Elut-C18. In order to achieve a high selectivity in the determination of SCCPs, GC-NCI-MS was used. Quality parameters of the optimised SPE and SPME procedures were determined, and the best results were obtained for the SPE/GC-NCI-MS method with LODs of 5 and 20 ng l(-1) for tap and river water, respectively. This method was successfully applied to the analysis of SCCPs in river water samples at concentrations below the microg l(-1) level.     

Determination of parathion in biological fluids by means of direct solid-phase microextraction

A new and simple procedure for the determination of parathion in human whole blood and urine using direct immersion (DI) solid-phase microextraction (SPME) and gas chromatography/mass spectrometry (GC/MS) is presented. This technique was developed using only 100 μL of sample, and ethion was used as internal standard (IS). A 65-μm Carbowax/divinylbenzene (CW/DVB) SPME fibre was selected for sampling, and the main parameters affecting the SPME process such as extraction temperature, adsorption and desorption time, salt addition, agitation and pH effect were optimized to enhance the sensitivity of the method. This optimization was also performed to allow the qualitative determination of parathion’s main metabolite, paraoxon, in blood. The limits of detection and quantitation for parathion were 3 and 10 ng/mL for urine and 25 and 50 ng/mL for blood, respectively. For paraoxon, the limit of detection was 50 ng/mL in blood. The method showed linearity between the LOQ and 50 μg/mL for both matrices, with correlation coefficients ranging from 0.9954 to 0.9999. Precision and accuracy were in conformity with the criteria normally accepted in bioanalytical method validation. The mean absolute recoveries were 35.1% for urine and 6.7% for blood. Other parameters such as dilution of sample and stability were also validated. Its simplicity and the fact that only 100 μL of sample is required to accomplish the analysis make this method useful in forensic toxicology laboratories to determine this compound in intoxications, and it can be considered an alternative to other methods normally used for the determination of this compound in biological media.     

Multiresidue method using SPME for the determination of various pesticides with different volatility in confined atmospheres

An analytical method is described for assessing the vapour concentration of 11 pesticides (bioallethrin, chlorpyriphos methyl, folpet, malathion, procymidone, quintozene, chlorothalonil, fonofos, penconazole and trimethacarb) in confined atmospheres (e.g. a greenhouse after pesticide application). This study is a successful extension of a method previously developed by the authors for dichlorvos to much less volatile pesticides. Sampling was performed by using polydimethylsiloxane–solid phase micro-extraction (PDMS–SPME) fibres immersed in a 250-mL sampling flask through which air samples were dynamically pumped from the analysed atmosphere. After a 40-min sampling duration, samples were analysed by GC/MS.Calibration was performed from a vapour-saturated air sample. The linearity of the observed signal versus pesticide concentration in the vapour phase was proved from spiked liquid samples whose headspace concentrations were measured by using the proposed method. This procedure gave calibration curves with regression coefficients (R²) greater than 0.98, and the repeatability of these measurements was found with RSDs of 1.9–7.6%. As a field application test, this analysis procedure was used for the determination of gaseous procymidone concentrations as a function of time in the atmosphere of an experimental 8-m² and 20-m³ greenhouse. The pesticide was sprayed according to real cultivation conditions, and measurements were made for 80 h after application (8 measurements). The observed concentrations found ranged from 200 to 500 µg m^–3, thus indicating the level of contamination of the air breathed by people in such working conditions.Abbreviations GC/MS gas chromatography/mass spectrometry - SIM selective ion monitoring - FC43 perfluorotributylamine - RSD relative standard deviation - LOD limit of detection - LOQ limit of quantification     

Gas chromatographic–mass spectrometric methodology using solid-phase microextraction for the multiresidue determination of pesticides in surface waters

Solid-phase microextraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) and selected ion monitoring (SIM) was used for the analytical determination of priority pesticide residues. Fibers coated with a 65-µm film thickness of polydimethylsiloxane divinylbenzene (PDMS-DVB) were used to extract 31 pesticides of different chemical groups. The quality parameters of the method demonstrated a good precision with detection limits of 1–56?ng/L. Linearity was controlled in the range of 0.1–50?µg/L. The proposed method was applied for the trace-level determination of the target pesticides in surface water samples including three rivers and one lake at the Epirus region (north-west Greece) for a period of one year. The results demonstrate the suitability of the SPME–GC–MS approach for the analysis of multi-residue pesticides in environmental water samples.     

Analysis of trace levels of pesticides in rainwater by SPME and GC-tandem mass spectrometry after derivatisation with PFFBr

Solid-phase microextraction (SPME) was used for the analysis of some pesticides (bromoxynil, chlorotoluron, diuron, isoproturon, 2,4-MCPA, MCPP and 2,4-D) in rainwater after derivatisation with PFBBr and gas chromatography-ion trap mass spectrometry. The derivatisation procedure was optimized by testing different methods: direct derivatisation in the aqueous phase followed by SPME extraction, on-fibre derivatisation and derivatisation in the injector. The best result was obtained by headspace coating the PDMS/DVB fibre with PFBBr for 10 min followed by direct SPME extraction for 60 min at 68 °C (pH 2 and 75% NaCl). Good detection limits were obtained for all the compounds: these ranged between 10 and 1,000 ng L⁻¹ with a relatively high uncertainty due to the combination of derivatisation and SPME extraction steps. The optimized procedure was applied to the analysis of pesticides in rainwater and results obtained shows that this method is a fast and simple technique to assess the spatial and temporal variations of concentrations of pesticides in rainwater.     

固相萃取–毛细管气相色谱法同时测定水体中8种有机磷类农药残留

建立固相萃取–毛细管气相色谱法同时测定水体中敌敌畏、乙酰甲胺磷、治螟磷、乐果、甲基对硫磷、马拉硫磷、杀螟硫磷和水胺硫磷8种有机磷类农药残留。样品经OASIS HLB固相萃取柱富集,丙酮洗脱,用毛细管气相色谱(FPD)法进行定量分析。8种有机磷类农残留的质量浓度在0.05~4.0μg/m L范围内与色谱峰面积线性关系良好,相关系数均大于0.998,方法检出限为0.004~0.01μg/m L。测定结果的相对偏差为2.6%~4.5%(n=6),加标回收率为81.6%~106.2%。该方法操作简单、灵敏度高,可用于检测水体中的8种有机磷类农药残留。     

Detection of organophosphate pesticides in human body fluids by headspace solid-phase microextraction (SPME) and capillary gas chromatography with nitrogen-phosphorus detection

Summary Organosphosphate pesticides have been found extractable by headspace solid-phase microextraction (SPME), and the best conditions of their extraction from human whole blood and urine samples have been investigated. The body fluid samples containing nine pesticides (IBP, methyl parathion, fenitrothion, malathion, fenthion, isoxathion, ethion, EPN and phosalone) were heated at 100°C in a septum-capped vial in the presence of various combinations of acid and salts, and SPME fiber was exposed to the headspace of the vial to allow adsorption of the pesticides before capillary gas chromatography (GC) with nitrogen-phosphorus detection. The heating with distilled water/HCl/(NH₄)₂SO₄/NaCl and with distilled water/HCl gave the best results for urine and whole blood, respectively. Recoveries of the nine pesticides were 0.8–10.6% except for phosalone (0.03%) for whole blood, and 3.8–40.2% for urine. The calibration curves for the pesticides showed linearity in the range of 50–400 ng/0.5 mL for whole blood except for malathion (100–400 ng/0.5 mL whole blood) and 7.5–120 ng/0.5 mL for urine except for phosalone (15–120 ng/0.5 mL urine) with detection limits of 2.2–40 ng/0.5 mL for whole blood and 0.8–12 ng/0.5 mL for urine.