一步法制备还原态氧化石墨烯载铂纳米粒子及其对甲醇氧化的电催化性能

以天然石墨为原料,采用改进的Hummers法制备氧化石墨.然后采用简单的一步化学还原法在乙二醇(EG)中同时还原氧化石墨烯(GO)和H₂PtCl₆制备高分散的铂/还原态氧化石墨烯(Pt/RGO)催化剂.采用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)和透射电子显微镜(TEM)对催化剂的微结构、组成和形貌进行表征.结果表明, GO已被还原成RGO, Pt纳米粒子均匀分散在RGO表面,粒径约为2.3 nm.采用循环伏安法和计时电流法评价催化剂对甲醇氧化的电催化性能,测试结果表明, Pt/RGO催化剂对甲醇氧化的电催化活性和稳定性与Pt/C和Pt/CNT相比有了很大提高.另外其对甲醇电催化氧化的循环伏安图中正扫峰电流密度(I_f)和反扫峰电流密度(I_b)的比值高达1.3,分别是Pt/C和Pt/CNT催化剂的2.2和1.9倍,表明Pt/RGO催化剂具有高的抗甲醇氧化中间体CO_ad的中毒能力.     

Polymerization of graphene oxide nanosheet by using of aminoclay: Electrocatalytic activity of its platinum nanohybrids

This study describes the polymerization of graphene oxide (GO) nanosheet to reduced‐GO‐aminoclay (RGC) by covalent functionalization of chemically reactive epoxy groups on the basal planes of GO with amine groups of magnesium phyllosilicate clay (known as aminoclay). The resulting RGC sheets were characterized and applied to support platinum nanostructures at toluene/water interface. Pt nanoparticles (NPs) with diameters about several nanometers were adhered to RGC sheets by chemical reduction of [PtCl₂(cod)] (cod = cis,cis‐1,5‐cyclooctadiene) complex. Catalytic activity of Pt NPs thin films were investigated in the methanol oxidation reaction. Cyclic voltammetry results exhibit that the Pt/reduced‐GO (RGO) and Pt/RGC thin films showed improved catalytic activity in methanol oxidation reaction in comparison to other Pt NPs thin films, demonstrating that the prepared Pt/RGO and Pt/RGC thin films are promising catalysts for direct methanol fuel cell.     

Electrochemical-reduced graphene oxide-modified carbon fiber as Pt–Au nanoparticle support and its high efficient electrocatalytic activity for formic acid oxidation

A simple electrochemical approach is developed to prepare reduced graphene oxide (RGO)-wrapped carbon fiber (CF) as a novel support for Pt–Au nanocatalysts. The obtained composite electrodes have been characterized by scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDX), thermal gravimetric analysis (TGA), and electrochemical methods. SEM images reveal that the Pt–Au nanoparticles deposited on RGO-wrapped CF (RGO/CF) electrode display smaller particle size and more uniform dispersion than those on the bare CF electrode. Cyclic voltammetry, linear sweep voltammetry, chronoamperometry, chronopotentiometry, Tafel plots, and electrochemical impedance spectroscopy (EIS) analyses demonstrate that the introduced RGO on CF electrode surface is beneficial to the dispersion of Pt–Au nanoparticles, as a consequence, to the enhancement of the electrocatalytic activity and the antipoisoning ability of Pt–Au towards formic acid electrooxidation.     

氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯（PANI-GO）,得到了氮掺杂的还原氧化石墨烯碳材料（N-RGO）,以其负载Pt 制备了Pt/N-RGO纳米结构电催化剂. 采用透射电镜（TEM）、X射线光电子能谱（XPS）、X 射线衍射（XRD）谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能. 结果表明：高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt 颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯(PANI-GO),得到了氮掺杂的还原氧化石墨烯碳材料(N-RGO),以其负载Pt制备了Pt/N-RGO纳米结构电催化剂.采用透射电镜(TEM)、X射线光电子能谱(XPS)、X射线衍射(XRD)谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能.结果表明:高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

Photocatalytically Renewable Micro‐electrochemical Sensor for Real‐Time Monitoring of Cells

Electrode fouling and passivation is a substantial and inevitable limitation in electrochemical biosensing, and it is a great challenge to efficiently remove the contaminant without changing the surface structure and electrochemical performance. Herein, we propose a versatile and efficient strategy based on photocatalytic cleaning to construct renewable electrochemical sensors for cell analysis. This kind of sensor was fabricated by controllable assembly of reduced graphene oxide (RGO) and TiO₂ to form a sandwiching RGO@TiO₂ structure, followed by deposition of Au nanoparticles (NPs) onto the RGO shell. The Au NPs‐RGO composite shell provides high electrochemical performance. Meanwhile, the encapsulated TiO₂ ensures an excellent photocatalytic cleaning property. Application of this renewable microsensor for detection of nitric oxide (NO) release from cells demonstrates the great potential of this strategy in electrode regeneration and biosensing.     

二氧化钛纳米颗粒/还原氧化石墨烯修饰玻碳电极在对硝基苯酚检测中的应用

本文报道了用二氧化钛纳米颗粒（TiO₂NPs）/还原氧化石墨烯（RGO）的复合物修饰玻碳电极检测微量对硝基苯酚（4-NP）的电化学方法. 本研究用扫描电子显微镜（SEM）对该复合材料形貌进行表征,用循环伏安法和交流阻抗谱对该复合物电极的电化学性能进行检测,表现出良好的电化学特性,采用差分脉冲伏安法对4-NP进行微量检测,结果令人满意,这主要得益于TiO2NPs/RGO复合物对4-NP有较高的催化活性,其电流峰值与浓度呈较高的线性关系,DPV的检测范围为10μmol·L^-1 ~ 350μmol·L^-1,检测限为0.13 μmol·L^-1. 与其他报道的一些电化学传感器相比,该传感器检测范围大,检测限低,且工作稳定,成本低,分析简单快速,具有很好的应用前景.     

碳化钨-石墨烯插层复合物的制备及作为甲醇氧化助催化剂的性能研究

直接甲醇燃料电池(DMFCs)作为一种环境友好、高效的新能源,对解决世界目前面临的“能源危机”与“环境危机”这两大问题有着至关重要的意义,具有较广阔的应用前景.目前,甲醇氧化催化剂仍然以 Pt基为主,但是 Pt价格昂贵,且容易受甲醇氧化中间产物的毒化,从而影响了 DMFCs的商业化进程.碳化钨(WC)作为非贵金属催化剂,在催化方面具有类铂的性能.在 WC上负载适量的 Pt,可以通过两者的协同效应加强催化剂的抗 CO中毒能力.但是,由于 WC的导电性能不佳,比表面积较小,因此寻找合适的载体显得尤为必要.在碳载体中,石墨烯(RGO)具有优良的导电性以及独特的片层结构,是电催化剂的理想载体.以 RGO为载体, WC为插层物质制备的 WC-RGO插层复合物具有化学稳定性好、电导率高且电化学活性面积大等优势.但是,由于石墨烯表面光滑且呈惰性,同时使用传统的碳化方法制备的碳化钨颗粒较大,因此,制备较小颗粒且分散均匀的 WC-RGO插层复合物具有较大难度.一般以偏钨酸铵和氧化石墨烯(GO)为前驱体制备 WC-RGO插层复合物,但是由于偏钨酸根和 GO都带负电,因此不能成功地将偏钨酸根引入到石墨烯的片层结构中,造成 WC-RGO插层复合物组装上的困难.本文采用硫脲成功地合成了具有高分散性 WC纳米颗粒插层在少层 RGO里的 WC-RGO插层复合物.硫脲((NH2)2CS)作为阴离子接受器,具有较强的结合阴离子形成稳定复合物的能力,同时它也是合成具有片层结构的过渡金属硫化物的原料之一.因此在 WC-RGO插层复合物组装过程中,硫脲既作为锚定及诱导剂,又是制备片层二硫化钨(WS2)的硫源.材料具体制备方法如下：首先利用浸渍法,将偏钨酸根阴离子([H2W12O40]6?)牵引到(NH2)2CS改性过的 GO上形成[H2W12O40]6?-(NH2)2CS-GO前驱体;然后将前驱体放入管式炉中还原碳化,前驱体先反应生成 WS2;由于 WS2自身的2D片层结构,反应中可以得到 WS2-RGO插层复合物,接着原位碳化生成 WC-RGO插层复合物.碳化钨-石墨烯负载铂电催化剂(Pt/WC-RGO)通过微波辅助法制得,并采用 X射线衍射、扫描电子显微镜、透射电子显微镜及激光拉曼光谱等手段对其结构与形貌进行了表征.结果显示,在 WC-RGO插层复合物中, WC的平均粒径为1.5 nm, RGO的层数约为5层.在甲醇电氧化反应中,相比于商用 Pt/C催化剂, Pt/WC-RGO插层复合物催化剂具有更高的电化学活性面积(ECSA)和较高的峰电流密度(246.1 m2/g Pt,1364.7 mA/mg Pt),分别是 Pt/C的3.66和4.77倍.我们分别利用 CO溶出伏安法、计时电流法及加速耐久性试验法验证了 Pt/WC-RGO催化剂优秀的抗 CO中毒能力及稳定性. Pt/WC-RGO催化剂特殊的插层结构,在增加 WC与 Pt接触机会以加强协同作用的同时,促进了催化过程中质量及电荷的转移,因而具有比 Pt/C更高的催化活性.可见,通过制备WC-RGO插层复合物可降低 Pt用量,从而大大地降低燃料电池中电催化剂的成本.同时,我们使用的是一种高效,可大批量生产纳米材料的方法,有助于催化剂的商业化.     

Selective and Simultaneous Determination of Dihydroxybenzene Isomers Based on Green Synthesized Gold Nanoparticles Decorated Reduced Graphene Oxide

In the present study, we report the simultaneous electrochemical determination of hydroquinone (HQ), catechol (CC) and resorcinol (RC) at gold nanoparticles (Au‐NPs) decorated reduced graphene oxide (RGO) modified electrode. An enhanced and well defined peak current response with a better peak separation of HQ, CC and RC is observed at RGO/Au‐NPs composite than that of RGO and Au‐NPs modified electrodes. The fabricated modified electrode shows a wide linear response in the concentration range of 3–90 µM, 3–300 µM and 15–150 µM for HQ, CC and RC, respectively. The detection limit of HQ, CC and RC is found as 0.15 µM, 0.12 µM and 0.78 µM, respectively.     

基于纳米Nb_2O_5/石墨烯复合材料的增强效应电化学测定绿原酸

制备了Nb_2O_5/石墨烯修饰玻碳电极(Nb_2O_5/RGO/GCE),建立了一种简便、灵敏检测绿原酸的电化学方法。用氧化石墨烯(GO)和五氯化铌(Nb Cl5)一步溶剂热法制备Nb_2O_5/RGO复合材料,并用扫描电子显微镜(SEM)对其进行形貌表征。采用循环伏安法(CV)和方波伏安法(SWV)研究了绿原酸在Nb_2O_5/RGO/GCE上的电化学行为。结果发现,Nb_2O_5/RGO复合材料能显著增强绿原酸的电化学活性。对实验条件(如pH值、扫描速率与富集时间等)进行了优化。在最佳条件下,绿原酸的氧化峰电流与浓度在5.0×10~(-7)~1.2×10~(-5)mol/L范围内呈良好的线性关系,检出限为2.0×10~(-7)mol/L。采用修饰电极测定各种药物中绿原酸的含量,得到加标回收率为96.6%~101.5%。该方法具有良好的灵敏度和稳定性,已成功应用于药物中绿原酸含量的测定。     

Functionalization of Graphene Derivatives with Conducting Polymers and Their Applications in Uric Acid Detection

In this article, we review recent progress concerning the development of sensorial platforms based on graphene derivatives and conducting polymers (CPs), alternatively deposited or co-deposited on the working electrode (usually a glassy carbon electrode; GCE) using a simple potentiostatic method (often cyclic voltammetry; CV), possibly followed by the deposition of metallic nanoparticles (NPs) on the electrode surface (ES). These materials have been successfully used to detect an extended range of biomolecules of clinical interest, such as uric acid (UA), dopamine (DA), ascorbic acid (AA), adenine, guanine, and others. The most common method is electrochemical synthesis. In the composites, which are often combined with metallic NPs, the interaction between the graphene derivatives—including graphene oxide (GO), reduced graphene oxide (RGO), or graphene quantum dots (GQDs)—and the CPs is usually governed by non-covalent functionalization through π–π interactions, hydrogen bonds, and van der Waals (VW) forces. The functionalization of GO, RGO, or GQDs with CPs has been shown to speed up electron transfer during the oxidation process, thus improving the electrochemical response of the resulting sensor. The oxidation mechanism behind the electrochemical response of the sensor seems to involve a partial charge transfer (CT) from the analytes to graphene derivatives, due to the overlapping of π orbitals.     

One-pot green synthesis of Prussian blue nanocubes decorated reduced graphene oxide using mushroom extract for efficient 4-nitrophenol reduction

One-pot green approach to the synthesis of Prussian blue nanocubes/reduced graphene oxide (PBNCs/RGO) nanocomposite had been attempted. It was based on the extract of mushroom with K₃[Fe(CN)₆] and graphene oxide (GO) as precursors, where the reduction of GO and the deposition of PBNCs occurred simultaneously. The obtained nanocomposite was characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy and electrochemical techniques. With the introduction of β-cyclodextrin (β-CD), the β-CD/PBNCs/RGO system showed linear behavior in the range from 0.01 to 700 μM for 4-nitrophenol with a low detection limit of 2.34 nM (S/N = 3).     

聚吡咯/还原氧化石墨烯复合物的合成及电容性能

通过原位聚合方法制备不同配比的聚吡咯/氧化石墨（PPy/GO）复合物,将其用NaBH4还原得到聚吡咯/还原氧化石墨烯(PPy/RGO)复合物,采用X射线衍射、红外光谱和场发射扫描电子显微镜（FESEM）对其结构和形貌进行物理表征。 采用循环伏安、恒电流充放电和交流阻抗等电化学方法系统研究了所制备样品的电化学性能。 实验结果表明,在电流密度为0.5 A/g、吡咯（Py）与GO质量比为95∶5时,得到的复合物还原前后比电容分别可达401.5和314.5 F/g,远高于单纯的GO（34.8 F/g）和PPy（267.5 F/g）。 经过1200圈循环稳定性测试后,PPy/RGO复合物比电容保持了原来的62.5%,与PPy和PPy/GO（电容保持率分别为16.8%和46.4%）相比,PPy/RGO表现出更好的循环稳定性能,有望成为超级电容器电极材料。     

A Sensitive and Selective Nitrite Detection in Water Using Graphene/Platinum Nanocomposite

A glassy carbon electrode modified with reduced graphene oxide and platinum nanocomposite film was developed simply by electrochemical method for the sensitive and selective detection of nitrite in water. The electrochemical reduction of graphene oxide (GO) efficiently eliminates oxygen‐containing functional groups. Pt nanoparticles were electrochemically and homogeneously deposited on the ErGO surface. Field emission scanning electron microscopy (FE‐SEM), Raman spectroscopy, attenuated total reflectance‐fourier transform infrared spectroscopy (ATR‐FTIR), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were used to examine the surface morphology and electrocatalytic properties of the Pt‐ErGO nanocomposite film‐modified electrode surface. The fabricated nitrite sensor showed good electrochemical performance with two linear ranges; one from 5 to 100 µM (R²=0.9995) and the other from 100 to 1000 µM (R²=0.9972) and a detection limit of 0.22 µM. The proposed sensor was successfully applied for the detection of nitrite in tap water samples which proves performance of the Pt‐ErGO nanocomposite films.     

Activated carbon/graphene composites with high-rate performance as electrode materials for electrochemical capacitors

Glucose-derived activated carbon (GAC)/reduced graphene oxide (RGO) composites are prepared by pre-carbonization of the precursors (aqueous mixture of glucose and graphene oxide) and KOH activation of the pyrolysis products. The effect of the mass ratio of graphene oxide (GO) in the precursor on the electrochemical performance of GAC/RGO composites as electrode materials for electrochemical capacitors is investigated. It is found that the thermally reduced graphene oxide sheets serves as a wrinkled carrier to support the activated carbon particles after activation. The pore size distribution and surface area are depended on the mass ratio of GO. Besides, the rate capability of GAC is improved by the introduction of GO in the precursor. The highest specific capacitance of 334 F g^?1 is achieved for the GAC/RGO composite prepared from the precursor with a GO mass ratio of 3 %.     

石墨烯/铂复合材料的制备及电化学性能研究

采用Hummers法制备氧化石墨,再超声分散于去离子水中形成稳定的氧化石墨分散液。分散液与氯铂酸溶液混合后,氧化石墨烯还原氯铂酸产生大量铂纳米粒子,铂粒子被牢固地锚在氧化石墨烯片上,最后将所得到的氧化石墨烯/铂复合物置于管式炉中在Ar/H2气氛中于800℃下热裂解制备出石墨烯/铂复合材料。形貌与纳米结构分析表明,氧化石墨已被彻底还原成石墨烯,铂纳米粒子均匀分散在褶皱的石墨烯纳米片间。电化学阻抗研究进一步揭示复合材料的电子转移阻抗明显小于石墨烯,呈示铂纳米粒子掺入石墨烯片层大大改善了导电性。石墨烯/铂复合材料应用于对苯二酚的电化学检测,检出限达1.6×10-7mol.L-1,这说明该材料具有优异的电催化性能。     

Electrochemical Biosensor Utilizing Supramolecular Association of Enzyme on Sol−gel Matrix Embedded Gold Nanoparticles Supported Reduced Graphene Oxide−cyclodextrin Nanocomposite

Herein we present β‐cyclodextrin (CD)‐functionalized reduced graphene oxide (RGO) nanosheets supported on silicate sol‐gel matrix‐embedded gold nanoparticles (Au NPs) modified electrode as a new affinity binding nanocomposite. The modified electrode is fabricated through layer‐by‐layer drop casting followed by immobilization of chemically modified enzyme conjugate (horse radish peroxidase (HRP)?adamantane carboxylic acid (ADA)). This affinity system is based on the supramolecular association between CDs and HRP?ADA and is mimicking the biological avidin?biotin interactions. CDs‐functionalized RGO (RGO?CD) functions as a macrocyclic host to form stable supramolecular inclusion complexes with enzyme conjugate. Besides Au NPs improve the interfacial interaction with RGO?CD nanosheets, and thus exhibit synergistic electrocatalytic effect toward H₂O₂ reduction in the presence of 1 mM hydroquinone.     

Graphene Nanocomposites Based Electrochemical Sensing Platform for Simultaneous Detection of Multi-drugs

Three reduced graphene oxide nanocomposites were employed to achieve the simultaneous electrochemical determination of multi-drugs including acetaminophen (ACTM), carbendazim (CB) and ciprofloxacin (CFX). All nanocomposite modified electrodes showed improved current responses for three drugs. Notably cauliflower-like platinum nanoparticles decorated reduced graphene oxide modified electrode (or Pt−RGO/GCE) exhibited the best performance in terms of electrochemical stability. Using Pt−RGO/GCE, the linear detect ranges of 30–120 μM, 25–115 μM and 10–25 μM, and detection limit values of 3.49, 2.96, and 1.53 μM were achieved for ACTM, CB and CFX respectively. The electrode was further used for the successful determination of above drugs in tap and river water using differential pulse voltammetry. From the obtained results, we believe that Pt-RGO/GCE is highly promising for the fabrication of robust electrochemical sensors for simultaneously determining ACTM, CB and CFX or similar types of drugs in the future.     

Triarylphosphine-stabilized platinum nanoparticles in three-dimensional nanostructured films as active electrocatalysts

Ligand-stabilized platinum nanoparticles (Pt NPs) can be used to build well-defined three-dimensional (3-D) nanostructured electrodes for better control of the catalyst architecture in proton exchange membrane fuel cells (PEMFCs). Platinum NPs of 1.7 +/- 0.5 nm diameter stabilized by the water-soluble phosphine ligand, tris(4-phosphonatophenyl)phosphine (TPPTP, P(4-C6H4PO3H2)3), were prepared by ethylene glycol reduction of chloroplatinic acid and subsequent treatment of the isolated nanoparticles with TPPTP. The isolated TPPTP-stabilized Pt NPs were characterized by multinuclear magnetic resonance spectroscopy (31P and 195Pt NMR), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and extended X-ray absorption fine structure (EXAFS). The negatively charged TPPTP-Pt NPs were electrostatically deposited onto a glassy carbon electrode (GCE) modified with protonated 4-aminophenyl functional groups (APh). Multilayers were assembled via electrostatic layer-by-layer deposition with cationic poly(allylamine HCl) (PAH). These multilayer films are active for the key hydrogen fuel cell reactions, hydrogen oxidation (anode) and oxygen reduction (cathode). Using a rotating disk electrode configuration, fully mass-transport limited kinetics for hydrogen oxidation was obtained after 3 layers of TPPTP-Pt NPs with a total Pt loading of 4.2 microg/cm2. Complete reduction of oxygen by four electrons was achieved with 4 layers of TPPTP-Pt NPs and a total Pt loading of 5.6 microg/cm2. A maximum current density for oxygen reduction was reached with these films after 5 layers resulting in a mass-specific activity, i(m), of 0.11 A/mg(Pt) at 0.9 V. These films feature a high electrocatalytic activity and can be used to create systematic changes in the catalyst chemistry and architecture to provide insight for building better electrocatalysts.     

An electrochemical sensor based on Pt nanoparticles decorated over-oxidized polypyrrole/reduced graphene oxide nanocomposite for simultaneous determination of two neurotransmitters dopamine and 5-Hydroxy tryptamine in the presence of ascorbic acid

Abstract

In this study, the Pt nanoparticles/over-oxidized polypyrrole nanofiber/reduced graphene oxide (Pt NPs/OPPy/RGO) nanocomposite was electrochemically synthesized and used to modify a glassy carbon electrode. To confirm the Surface morphology and characterization of the nanocomposite, field emission scanning microscopy (FE-SEM), X-ray diffraction (XRD), Raman, FT-IR, and X-ray photoelectron spectroscopy (XPS) were used. Simultaneous determination of these species showed one linear response 0.1–250.0?μM and two linear responses 0.5–10.0?μM and 10.0–470.0?μM, with detection limits 42?nM and 106?nM (S/N?=?3) for DA and 5-HT, respectively. Finally, the analytical application of this modified electrode was investigated in the human blood plasma.