Zr4+对固相反应制备堇青石材料晶相转变的影响

以菱镁矿风化石、工业氧化铝和二氧化硅微粉为原料,加入不同含量二氧化锆添加剂,通过固相反应合成制备堇青石。用XRD法和SEM法表征试样中的晶相和显微结构,用X′Pert Plus软件对结晶相的晶胞参数和结晶度进行分析,用半定量法对试样晶相组成进行计算,用Scherrer公式计算堇青石的晶粒大小。研究分析Zr4+对制备堇青石材料中晶相组成、晶粒大小、晶胞常数、结晶度及显微结构的影响。结果表明:Zr4+对堇青石结构中Mg2+的置换固溶作用使堇青石相晶胞常数及晶胞体积发生变化,形成的结构缺陷使堇青石结构中离子扩散速度加快。由于Zr4+较高的电场强度,减弱了Mg-O的键力,氧化铝和二氧化硅通过固相反应形成莫来石相。当二氧化锆加入量为1.2%时,堇青石晶胞常数和晶胞体积最大,堇青石晶粒最大,堇青石结构中莫来石含量达到2.5%。     

La3+,Ce4+对制备堇青石材料晶相转变及烧结性能的影响

以菱镁矿风化石、工业氧化铝和二氧化硅微粉为原料,加入不同含量氧化镧、氧化铈添加剂,通过固相反应合成制备堇青石材料。用XRD法和SEM法表征试样中的晶相组成和显微结构,用X’Pert Plus软件计算主晶相的晶格常数、晶胞体积和试样的相对结晶度,用半定量法计算试样中各晶相含量,用Scherrer公式计算主晶相的粒径大小。研究分析了La3+,Ce4+对制备堇青石材料晶相组成、主晶相粒径大小、晶胞常数、试样相对结晶度、显微结构及烧结性能的影响。结果表明:氧化镧比氧化铈具有更好的助堇青石烧结性,加入氧化镧的堇青石试样具有更好的致密性;随着氧化镧、氧化铈加入量的增加,堇青石晶胞常数和晶胞体积呈现先增大后减小趋势;Ce4+更高的电场强度促进了堇青石材料更容易发生晶相转变形成莫来石。     

利用铝废渣制备片状堇青石的影响因素研究

以铝厂废渣、高岭土、滑石为主要原料,采用固相法合成片状堇青石。分析了原料种类、原料配方、烧结温度、保温时间和晶核剂对合成堇青石的影响,并通过XRD、SEM进行表征。结果表明,原料的纯度越高合成的堇青石纯度越高;富含镁的配方能完全形成堇青石相;最佳烧成温度为1 380℃,保温时间为4 h,此时得到的堇青石纯度最高,且呈现片状结构,颗粒大小均匀;堇青石熟料可以起到晶核剂的作用,促进堇青石的生成。     

稻壳一步法制备堇青石-莫来石多孔陶瓷

以稻壳、Al_2O_3和MgO为主要原料,按偏镁铝方案确定堇青石的组成,并以堇青石与莫来石质量比为7∶3进行配料,再掺少量Nd_2O_3为烧结助剂,用一步法烧成了堇青石-莫来石多孔陶瓷。测定了烧结试样的抗弯强度、显气孔率、热膨胀系数,用XRD分析了试样在烧结过程中的物相组成变化,并用SEM观察其显微结构。研究结果表明:在掺2%Nd_2O_3,1380℃保温5h条件下,制备的多孔陶瓷的抗弯强度为20.55MPa,显气孔率48.34%,热膨胀系数3.5×10~(-6)·℃-1,其主晶相为堇青石和莫来石,SEM显示晶体间存在大量孔隙。     

CaO杂质对铝型材厂工业污泥合成堇青石材料晶相结构及其含量影响

探讨原料组成对铝型材厂工业污泥合成堇青石材料的影响是非常重要的。研究目的有助于确定不同杂质在原料中允许的存在量,为选择其他原料提供可靠的依据。采用XRD法和SEM法分析各试样的晶相结构:用半定量分析方法确定各晶相的含量:用philipsX抪ertplus软件确定试样中各晶相结构参数。实验结果表明:CaO杂质含量从1.2~2.5%对合成堇青石有利:从2.5~2.8%堇青石含量开始下降:确定2.5%为CaO杂质最佳存在量,其对应的堇青石含量为91%。经plus软件确定结果:CaO杂质含量为1.2%时,其结构与单晶相同,晶胞参数变化很小:CaO含量从1.2~2.8%,其晶系由六方转变为四方结构,晶胞参数发生较大变化。镁铝尖晶石结构与晶胞参数变化较大,由单晶的立方结构转变为四方结构。     

反应温度与时间对铝型材厂工业污泥合成堇青石材料的得率与晶相结构影响

本研究主要探讨反应温度和反应时间对铝型材厂工业污泥合成堇青石材料的得率和晶相结构的影响。该污泥系由铝型材表面处理时产生的大量废液, 经沉淀过滤所得。主要成分是一种超细的γ-AlOOH, 其中部分是晶体, 部分是无定形体, 活性很高, 有利于堇青石晶相的形成, 能降低反应温度。 实验结果表明: 堇青石含量随着反应温度升高而增加; 晶相结构和晶胞参数与反应温度有关; 确定1350℃为最佳的反应温度; 反应时间在 2~5 h的试样中,堇青石含量增加, 在5~6 h含量降低. 5 h为最佳的反应时间。     

ZnO掺杂堇青石基红外陶瓷粉体的研制与表征

采用固相烧结法制备了ZnO替代MgO掺杂的堇青石基红外陶瓷粉体,通过红外辐射率测试、X射线衍射、热分析和红外吸收光谱等分析与表征,探讨了烧成温度、ZnO的掺杂量对其红外辐射率的影响.结果表明,在烧成温度为1 380 ℃、ZnO的掺杂量为22.5%(物质的量分数)时,所获得的堇青石基红外陶瓷粉体为单一相晶体,结晶完全,红外辐射率达0.978;适量地掺杂ZnO替代MgO,可在结构中使Zn2+代替Mg2+,引起堇青石结构中的非对称性,从而提高堇青石的红外吸收能力和辐射能力.     

Na_2O-SiO_2-Al_2O_3-NaCl-H_2O体系中ANA和SOD沸石膜的水热合成

Na2 O SiO2 Al2 O3 NaCl H2 O体系中,以水玻璃和准一水软铝石为原料,分别在堇青石和玻璃载体上水热合成方沸石(ANA)与方钠石(SOD)沸石膜.研究水含量、反应温度、反应时间与多次合成对膜结晶的影响.用XRD,SEM,EDX表征膜的晶相、形貌和化学组成.堇青石负载方沸石膜在对 95 %(wt.)乙醇水溶液的渗透蒸发实验中,水优先透过沸石膜的选择性显示了晶间孔的醇/水分离作用.非计量的NaCl进入到在玻璃载体上成膜的方钠石笼中,致使该膜显示光致变色效应     

Na2O-SiO2-Al2O3-NaCl-H2O体系中ANA和SOD沸石膜的水热合成

Na2O-SiO2-Al2O3-NaCl-H2O体系中，以水玻璃和准一水软铝石为原料，分别在 堇青石和玻璃载体上水热合成方沸石（ANA）和方钠石（SOD）沸石膜。研究水含量 、反应温度、反应时间与多次合成对膜结晶的影响。用XRD，SEM，EDX表征膜的晶 相、形貌和化学组成。堇青石负载方沸石膜在对95％（wt.)乙醇水溶液的渗透蒸发 实验中，水优先透过沸石膜的选择性显示了晶间孔的醇／水分离作用。非计量的 NaCl进入到在玻璃载体上成膜的方钠石笼中，致使该膜显示光致变色效应。     

低成本原料一步直接合成小晶粒ZSM-5分子筛

以硫酸铝、水玻璃、正丁胺、水、晶种、NaCl、浓硫酸等低成本试剂为原料,一步直接合成法制备了高结晶度小晶粒ZSM-5分子筛,详细考察了凝胶陈化方式、滴加顺序、晶化时间、晶化温度、水量及原料硅铝比对分子筛结晶度及粒度的影响.通过XRD、SEM等对合成的分子筛进行了详细表征.研究结果表明:采用低温水浴回流搅拌陈化方式、在160～170℃、晶化30 h可获得高结晶度小晶粒ZSM-5分子筛.正反加顺序对分子筛结晶度影响不大.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.