Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Bioactive glass and hydroxyapatite thin films obtained by pulsed laser deposition

Bioactive glass (BG), calcium hydroxyapatite (HA), and ZrO₂ doped HA thin films were grown by pulsed laser deposition on Ti substrates. An UV KrF^* (λ = 248 nm, τ ≥ 7 ns) excimer laser was used for the multi-pulse irradiation of the targets. The substrates were kept at room temperature or heated during the film deposition at values within the (400-550 °C) range. The depositions were performed in oxygen and water vapor atmospheres, at pressure values in the range (5-40 Pa). The HA coatings were heat post-treated for 6 h in a flux of hot water vapors at the same temperature as applied during deposition. The surface morphology, chemical composition, and crystalline quality of the obtained thin films were studied by scanning electron microscopy, atomic force microscopy, and X-ray diffractometry. The films were seeded for in vitro tests with Hek293 (human embryonic kidney) cells that revealed a good adherence on the deposited layers. Biocompatibility tests showed that cell growth was better on HA than on BG thin films.     

Study of the structure and electrical properties of the copper nitride thin films deposited by pulsed laser deposition

Copper nitride thin films were prepared on glass and silicon substrates by ablating a copper target at different pressure of nitrogen. The films were characterized in situ by X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and ex situ by X-ray diffraction (XRD). The nitrogen content in the samples, x = [N]/[Cu], changed between 0 and 0.33 for a corresponding variation in nitrogen pressure of 9 × 10⁻² to 1.3 × 10⁻¹ Torr. Using this methodology, it is possible to achieve sub-, over- and stoichiometric films by controlling the nitrogen pressure. The XPS results show that is possible to obtain copper nitride with x = 0.33 (Cu₃N) and x = 0.25 (Cu₄N) when the nitrogen pressure is 1.3 × 10⁻¹ and 5 × 10⁻² Torr, respectively. The lattice constants obtained from XRD results for copper nitride with x = 0.25 is of 3.850 Å and with x = 0.33 have values between 3.810 and 3.830 Å. The electrical properties of the films were studied as a function of the lattice constant. These results show that the electrical resistivity increases when the lattice parameter is decreasing. The electrical resistivity of copper nitride with x = 0.25 was smaller than samples with x = 0.33.     

Enhanced dielectric permittivity in poly (vinylidene) fluoride/multiwalled carbon nanotubes nanocomposite thin films fabricated by pulsed laser deposition

The fabrication of high quality thin films of poly (vinylidene fluoride) embedded with multiwalled carbon nanotubes using pulsed laser deposition technique is reported. The prepared films were characterized for structural, morphology and dielectric properties. The morphology analysis revealed uniform dispersion of multiwalled carbon nanotubes throughout the polymer matrix. X-ray diffraction results suggested that the poly (vinylidene fluoride) film is in amorphous phase while addition of multiwalled carbon nanotubes showed presence of crystalline peaks in the nanocomposites films. It was interesting to note that the nanocomposite films exhibits significant enhancement of the ferroelectric β-phase as evidenced by the X-ray diffraction and Fourier transform infrared spectroscopy results. The dielectric analysis shows a remarkable enhancement in the dielectric permittivity of nanocomposites with lower loss and conductivity level. The results can be attributed to the formation of minicapacitor network and relatively higher percolation threshold in the nanocomposites.     

Non-stoichiometry-induced metal-to-insulator transition in nickelate thin films grown by pulsed laser deposition

While controlling the cation contents in perovskite rare-earth nickelate thin films, a metal-to-insulator phase transition is reported. Systematic control of cation stoichiometry has been achieved by manipulating the irradiation of excimer laser in pulsed laser deposition. Two rare-earth nickelate bilayer thin-film heterostructures with the controlled cation stoichiometry (i.e. stoichiometric and Ni-excessive) have been fabricated. It is found that the Ni-excessive nickelate film is structurally less dense than the stoichiometric film, albeit both of them are epitaxial and coherent with respect to the underlying substrate. More interestingly, as a temperature decreases, a metal-to-insulator transition is only observed in the Ni-excessive nickelate films, which can be associated with the enhanced disproportionation of the Ni charge valence. Based on our theoretical results, possible origins (e.g. anti-site defects) of the low-temperature insulating state are discussed with the need of future work for deeper understanding. Our work can be utilized to realize unusual physical phenomena (e.g. metal-to-insulator phase transitions) in complex oxide films by manipulating the chemical stoichiometry in pulsed laser deposition.     

Crystallization and grain growth characteristics of yttria-stabilized zirconia thin films grown by pulsed laser deposition

Knowledge about the crystallization and grain growth characteristics of metal oxide thin films is essential for effective microstructural engineering by thermal post-annealing and the integration to Si-based miniaturized electroceramic devices. Finite size and interface effects may cause fundamentally different behavior compared to three dimensional macroscopic systems. This work presents a comprehensive investigation of the crystallization kinetics and microstructural evolution upon thermal post-annealing of amorphous 200 nm and 1.2 μm thin films of 8 mol% yttria-stabilized zirconia grown by pulsed laser deposition (PLD) using ex- and in-situ X-ray diffraction, Raman spectroscopy, and electron microscopy techniques. The layers exhibit a remarkably low crystallization temperature of 200-250 °C while exposure to energetic electrons induces the formation of randomly dispersed ~ 20 nm sized crystallites already at ambient temperature. The isothermal amorphous to crystalline phase transformation kinetics can be described quantitatively by the Johnson-Mehl-Avrami-Kolmogorov model. They reveal characteristics of a three dimensional growth under cation bulk diffusion control with heterogeneous nucleation that changes from continuous to instantaneous initial seeding at temperatures above 300 °C. Large (> 100 nm) equiaxed grains are formed rapidly without a stabilization of transient nanocrystals during the thermally induced phase transformation. A stagnation of normal grain growth resulting in a logarithmic normal size distribution is observed once the average grain dimensions approach the film thickness. The results on the crystallization and grain growth of the PLD-grown YSZ films are evaluated with regards to the fabrication of YSZ solid electrolyte membranes for Si-supported micro solid oxide fuel cells and gas sensors.     

Properties of Dy-doped ZnO nanocrystalline thin films prepared by pulsed laser deposition

Highly transparent conductive Dy₂O₃ doped zinc oxide (ZnO)_1-x(Dy₂O₃)_x nanocrystalline thin films with x from 0.5% to 5% have been deposited on glass substrate by pulsed laser deposition technique. The structural, electrical and optical properties of Dy₂O₃ doped thin films were investigated as a function of the x value. The experimental results show that the Dy concentration in Dy-doped ZnO thin films has a strong influence on the material properties especially electrical properties. The resistivity decreased to a minimum value of 5.02 × 10⁻⁴ Ω cm with x increasing from 0.5% to 1.0%, then significantly increased with the further increasing of x value. On the contrary, the optical direct band gap of the (ZnO)_1-x(Dy₂O₃)_x films first increased, then decreased with x increasing. The average transmission of Dy₂O₃ doped zinc oxide films in the visible range is above 90%.     

High temperature growth of InN on various substrates by plasma-assisted pulsed laser deposition

InN has attracted much attention due to its optical and electrical properties that make it suitable for the fabrication of infrared optical devices and high-speed electronic devices. In this work we report on the structural properties and morphology of InN thin films grown on different substrates by radiofrequency plasma beam assisted pulsed laser deposition. Sapphire and silicon substrates were considered for the growth of these films. The influence of substrate type and growth parameters on the morphology and structural properties of the resulting InN thin films is discussed. The structural analysis of the samples was performed by means of X-ray diffraction. The morphology of the thin films was investigated through atomic force microscopy. Although growth of InN from a metallic In target using nitrogen radiofrequency plasma assisted pulsed laser deposition was achieved for all the samples, growth conditions were found to play an important role on the crystal quality of the resulting thin films.     

Pulsed laser deposition and its current research status in preparing hydroxyapatite thin films

Pulsed laser deposition (PLD) is a conceptually and experimentally simple yet highly versatile tool for thin films and multi-layer film research. The mechanisms, advantages and disadvantages of pulsed laser deposition were reviewed. The process and some methods to resolve the drawbacks of PLD were discussed. Pulsed laser deposition of hydroxyapatite thin films was reviewed. Simple adjustment of PLD parameters can deposit hydroxyapatite in situ in crystalline form, amorphous films or HA with other calcium phosphate phases. Compared with plasma sprayed HA coatings the pulsed laser deposition HA thin films have higher coating/substrate adhesion and have minor undesirable phases under optimal conditions. Finally, we suggested some new researches should be done.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Pulsed laser deposition of fluoride glass thin films

The development of integrated waveguide lasers for different applications such as marking, illumination or medical technology has become highly desirable. Diode pumped planar waveguide lasers emitting in the green visible spectral range, e.g. thin films from praseodymium doped fluorozirconate glass matrix (called ZBLAN, owing to the main components ZrF₄, BaF₂, LaF₃, AlF₃ and NaF) as the active material pumped by a blue laser diode, have aroused great interest. In this work we have investigated the deposition of Pr:ZBLAN thin films using pulsed laser radiation of λ = 193 and λ = 248 nm. The deposition has been carried out on MgF₂ single crystal substrates in a vacuum chamber by varying both processing gas pressure and energy fluence. The existence of an absorption line at 210 nm in Pr:ZBLAN leads to absorption and radiative relaxation of the absorbed laser energy of λ = 193 nm preventing the evaporation of target material. The deposited thin films consist of solidified and molten droplets and irregular particulates only. Furthermore, X-ray radiation has been applied to fluoride glass targets to enhance the absorption in the UV spectral region and to investigate the deposition of X-ray treated targets applying laser radiation of λ = 248 nm. It has been shown that induced F-centres near the target surface are not thermally stable and can be easily ablated. Therefore, λ = 248 nm is not suitable for evaporation of Pr:ZBLAN.     

Structural characterization of AlN films synthesized by pulsed laser deposition

We obtained AlN thin films by pulsed laser deposition (PLD) from a polycrystalline AlN target using a pulsed KrF* excimer laser source (248 nm, 25 ns, intensity of ∼4 × 10⁸ W/cm², repetition rate 3 Hz, 10 J/cm² laser fluence). The target-Si substrate distance was 5 cm. Films were grown either in vacuum (10⁻⁴ Pa residual pressure) or in nitrogen at a dynamic pressure of 0.1 and 10 Pa, using a total of 20,000 subsequent pulses. The films structure was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and spectral ellipsometry (SE). Our TEM and XRD studies showed a strong dependence of the film structure on the nitrogen content in the ambient gas. The films deposited in vacuum exhibited a high quality polycrystalline structure with a hexagonal phase. The crystallite growth proceeds along the c-axis, perpendicular to the substrate surface, resulting in a columnar and strongly textured structure. The films grown at low nitrogen pressure (0.1 Pa) were amorphous as seen by TEM and XRD, but SE data analysis revealed ∼1.7 vol.% crystallites embedded in the amorphous AlN matrix. Increasing the nitrogen pressure to 10 Pa promotes the formation of cubic (≤10 nm) crystallites as seen by TEM but their density was still low to be detected by XRD. SE data analysis confirmed the results obtained from the TEM and XRD observations.     

Preparation and characterizations of amorphous nanostructured SiC thin films by low energy pulsed laser deposition

Amorphous silicon carbide (SiC) thin films were deposited on silicon substrates by pulsed laser ablation at room temperature. Thicknesses and surface morphology of the thin films were characterized using optical profilers, atomic force and field emission scanning electron microscopy. Nanohardnes, modulus and scratch resistance properties were determined using XP nanoindenter. The results show that crack free, smooth and nanostructured thin films can be deposited using low laser energy densities.     

Investigation of transmittance property of Palladium thin films fabricated by pulsed laser deposition with polarization using single layer model

In this paper the structure, morphology and optical properties of Pd thin films deposited on glass substrate by pulse laser deposition technique at two different substrate temperatures have been investigated. The fabricated films were characterized by various methods such as XRD, AFM, and UV-vis-NIR spectroscopy. The influence of surface roughness and angle of incidence with p polarization was investigated experimentally by optical property of palladium (Pd) thin films of two different thicknesses and rms roughness from transmission measurement in the visible spectral range. It has been shown that the experimental transmittance spectra agree well with their theoretical values for absorbing Pd thin film. The transmittance of thin film increases with increase in incident angle for the same sample.     

Nanocomposite oxide thin films grown by pulsed energy beam deposition

Highly non-stoichiometric indium tin oxide (ITO) thin films were grown by pulsed energy beam deposition (pulsed laser deposition-PLD and pulsed electron beam deposition-PED) under low oxygen pressure. The analysis of the structure and electrical transport properties showed that ITO films with a large oxygen deficiency (more than 20%) are nanocomposite films with metallic (In, Sn) clusters embedded in a stoichiometric and crystalline oxide matrix. The presence of the metallic clusters induces specific transport properties, i.e. a metallic conductivity via percolation with a superconducting transition at low temperature (about 6 K) and the melting and freezing of the In-Sn clusters in the room temperature to 450 K range evidenced by large changes in resistivity and a hysteresis cycle. By controlling the oxygen deficiency and temperature during the growth, the transport and optical properties of the nanocomposite oxide films could be tuned from metallic-like to insulating and from transparent to absorbing films.     

Deposition of zinc oxide thin films by reactive pulsed laser ablation

Thin films of zinc oxide have been deposited by reactive pulsed laser ablation of Zn and ZnO targets in presence of a radio frequency (RF) generated oxygen plasma. The gaseous species have been deposited at several substrate temperatures, using the on-axis configuration, on Si (1 0 0). Thin films have been characterized by scanning electron microscopy, atomic force microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and infrared spectroscopy. A comparison among conventional PLD and reactive RF plasma-assisted PLD has been performed.     

Pulsed laser deposition of doped skutterudite thin films

Ca_xCo₄Sb₁₂ skutterudite thin films have been prepared by pulsed laser deposition using a Nd:YAG laser working at 532 or 266 nm of wavelength. Characterization has been carried out by X-ray diffraction, atomic force microscopy and scanning electron microscopy. Emphasis has been put on the difficulty to obtain the skutterudite phase. Influence of the deposition temperature, the way of sticking the substrate, the laser fluence, the base pressure prior to deposition and the laser wavelength has been studied. All parameters revealed to have a drastic effect, and the skutterudite could only be achieved in a very narrow range of temperature and laser fluence, for a given wavelength, showing the importance on how these parameters are measured to ensure reproducible results.     

Characterization of pulsed laser deposited chalcogenide thin layers

In this work we report on pulsed laser deposition (PLD) of chalcogenide thin films from the systems (AsSe)_100−xAgI_x and (AsSe)_100−xAg_x for sensing applications. A KrF* excimer laser (λ = 248 nm; τ_FWHM = 25 ns) was used to ablate the targets that had been prepared from the synthesised chalcogenide materials. The films were deposited in either vacuum (4 × 10⁻⁴ Pa) or argon (5 Pa) on silicon and glass substrates kept at room temperature. The basic properties of the films, including their morphology, topography, structure, and composition were characterised by complementary techniques. Investigations by X-ray diffraction (XRD) confirmed the amorphous nature of the films, as no strong diffraction reflections were found. The film composition was studied by energy dispersive X-ray (EDX) spectroscopy. The morphology of the films investigated by scanning electron microscopy (SEM), revealed a particulate-covered homogeneous surface, typical of PLD. Topographical analyses by atomic force microscopy (AFM) showed that the particulate size was slightly larger in Ar than in vacuum. The uniform surface areas were rather smooth, with root mean square (rms) roughness increasing up to several nanometers with the AgI or Ag doping. Based upon the results from the comprehensive investigation of the basic properties of the chalcogenide films prepared by PLD and their dependence on the process parameters, samples with appropriate sorption properties can be selected for possible applications in cantilever gas sensors.     

Structure, morphology and optical properties of SiO2−x thin films prepared by plasma-assisted pulsed laser deposition

The amorphous silicon oxide SiO_2−x thin films were prepared by the plasma-assisted pulsed laser deposition (PLD) method. X-ray diffraction spectrometry (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-VIS-NIR scanning spectrophotometry and ellipsometry were used to characterize the crystallinity, microscopic morphology and optical properties of obtained thin films. The influences of substrate temperatures, oxygen partial pressures and oxygen plasma assistance on the compositions of silicon oxide (SiO_2−x) thin films were investigated. Results show that the deposited thin films are amorphous and have high surface quality. Stoichiometric silicon dioxide (SiO₂) thin film can be obtained at elevated temperature of 200 °C in an oxygen plasma-assisted atmosphere. Using normal incidence transmittance, a novel and simple method has been proposed to evaluate the value of x in transparent SiO_2−x thin films on a non-absorbing flat substrate.