Microstructure and tribological properties of TiCu2Al intermetallic compound coating

TiCu₂Al ternary intermetallic compound coating has been in situ synthesized successfully on pure Ti substrate by laser cladding. Tribological properties of the prepared TiCu₂Al intermetallic compound coating were systematically evaluated. It was found that the friction coefficient and wear rate was closely related to the normal load and sliding speed, i.e., the friction coefficient of the prepared TiCu₂Al intermetallic compound coating decreased with increasing normal load and sliding speed. The wear rate of the TiCu₂Al intermetallic compound coating decreased rapidly with increasing sliding speed, while the wear rate first increased and then decreased at normal load from 5 to 15 N.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Influence of heat treatment on tribological properties of electroless Ni-P and Ni-P-Al2O3 coatings on Al-Si casting alloy

Evolution of tribological properties of electroless Ni-P and Ni-P-Al₂O₃ coating on an Al-10Si-0.3Mg casting alloy during heat treatment is investigated in this work. The pre-treated substrate was plated using a bath containing nickel hypophosphite, nickel lactate and lactic acid. For preparation of fiber-reinforced coating Al₂O₃ Saffil fibers pre-treated in demineralised water were used. The coated samples were heat treated at 400-550 °C/1-8 h. Tribological properties were studied using the pin-on-disc method. It is found that the best coating performance is obtained using optimal heat treatment regime (400 °C/1 h). Annealing at higher temperatures (450 °C and above) leads to the formation of intermetallic compounds that reduce the coating wear resistance. The reason is that the intermetallic phases adversely affect the coating adherence to the substrate. The analysis of wear tracks proves that abrasion is major wear mechanism, however due to the formed intermetallic sub-layers, partial coating delamination may occur during the pin-on-disc test on the samples annealed at 450 °C and above. It was found that fiber reinforcement reduces this scaling and increases wear resistance of coatings as compared to the non-reinforced Ni-P coatings.     

Influences of laser remelting on microstructure of nanostructured Al2O3-13 wt.% TiO2 coatings fabricated by plasma spraying

The effects of laser remelting on microstructure of nanostructured Al₂O₃-13 wt.% TiO₂ ceramic coatings prepared by plasma spraying with agglomerated powders were studied. The microstructure of the feedstock, as-sprayed and laser-remelted coatings were investigated by using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffractometry (XRD). The results indicate that the plasma-sprayed ceramic coating consists of both fully melted regions and partially melted regions. The totally ceramic coating, especially the fully melted regions, has a typical plasma-sprayed lamellar-like structure as the conventional coating, and has some pores. According to the difference of microstructures, the partially melted regions can be divided into liquid-phase sintered regions (a three-dimensional net or skeleton-like structure: Al₂O₃-rich submicron particles embedded in the TiO₂-rich matrix) and solid-phase sintered regions (remained nanoparticles). The lamellar defect of the as-sprayed coating is erased, and the compactness of the coating is improved significantly after laser remelting. The laser-remelted region composed of fine equiaxed grains, which are different from the conventional column-like crystals along the direction of the heat current. Due to the rapid solidification of laser remelting process, there are still some nanoparticles in the remelted region because of an insufficient time for grains growth.     

Wear Performance and Mechanisms of Polyphenylene Sulfide/Polytetrafluoroethylene Wax Composite Coatings Reinforced by Graphene

Polyphenylene sulfide (PPS) composite coatings reinforced by graphene were prepared through a spraying method. Wear performance of the composite coatings were evaluated using a block-on-ring test rig, and the results showed that the wear life of the composite coatings were over seven times higher than that of a pure PPS coating. Wear mechanisms of PPS composite coatings reinforced by graphene are discussed. It was concluded that adhesive wear was the major wear mechanism of the pure PPS coating but the wear form of the composite coatings was dominated by abrasive wear due to the graphene filler that has high mechanical strength. In addition, fatigue wear appeared for composite coatings with higher content of graphene. The formation of a uniform thin transfer film on the counterpart ring and fine wear debris for the composites coatings during abrasion were consistent with the improvement of wear performance. The 3D morphology of the surface of the counterpart ring was also used to discuss the wear mechanism of PPS composite coatings.     

Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser

A high wear-resistant gradient coating made of Ni/Co-based alloys on the surface of a Cu alloy substrate was synthesized using a YAG laser induced in situ reaction method. The coating consists of three layers: the first is a Ni-based alloy layer, the second and third are Co-based alloy layers. The microhardness increases gradually from 98 HV in the Cu alloy substrate to the highest level of 876 HV in the third layer. The main phase of the Co-based alloy layer is CoCr₂(Ni,O)₄, coexisting with the Fe₁₃Mo₂B₅, Cr(Co(Mo, and FeCr_0.29Ni_0.16C_0.06 phases. Wear tests indicate that the gradient coating has good bond strength and wear properties with a wear coefficient of 0.31 (0.50 for the Cu alloy substrate). Also, the wear loss of the coating is only 0.01 g after it has been abraded for 60 min, which is only one fifth of that of the Cu alloy of the crystallizer. Wear tests of the gradient coating reveal good adhesive friction and wear properties when sliding against steel under dry conditions. This novel technique may have good application to make an advanced coating on the surface of the Cu alloy crystallizer in a continuous casting process.     

The study on porosity and thermophysical properties of nanostructured La2Zr2O7 coatings

Lanthanum-zirconium nano-powders were synthesized by molten salts method. Nanostructured lanthanum-zirconium coatings were deposited by air plasma spraying. Scanning electron microscopy and X-ray diffraction were carried out to analyze the as-sprayed coatings and powders. The pore size distribution and buck density of coatings were identified by mercury intrusion porosimetry. The thermophysical properties of the nanostructured coatings were also examined through laser flash technique and differential scanning calorimetry. The results demonstrate that the as-sprayed nanostructured coatings consist of the pyrochlore-type phase. The as-sprayed nanostructured lanthanum-zirconium coatings have a very low porosity. The thermal conductivity of the as-sprayed nanostructured lanthanum-zirconium coating is lower than that of the conventional coating between 200 °C and 950 °C, but when the temperature between 950 °C and 1300 °C, the result is reverse.     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Microstructure and wear behaviors of laser clad NiCr/Cr3C2-WS2 high temperature self-lubricating wear-resistant composite coating

The high temperature self-lubricating wear-resistant NiCr/Cr₃C₂-30%WS₂ coating and wear-resistant NiCr/Cr₃C₂ coating were fabricated on 0Cr18Ni9 austenitic stainless steel by laser cladding. Phase constitutions and microstructures were investigated, and the tribological properties were evaluated using a ball-on-disc wear tester under dry sliding condition at room-temperature (17 °C), 300 °C and 600 °C, respectively. Results indicated that the laser clad NiCr/Cr₃C₂ coating consisted of Cr₇C₃ primary phase and γ-(Fe,Ni)/Cr₇C₃ eutectic colony, while the coating added with WS₂ was mainly composed of Cr₇C₃ and (Cr,W)C carbides, with the lubricating WS₂ and CrS sulfides as the minor phases. The wear tests showed that the friction coefficients of two coatings both decrease with the increasing temperature, while the both wear rates increase. The friction coefficient of laser clad NiCr/Cr₃C₂-30%WS₂ is lower than the coating without WS₂ whatever at room-temperature, 300 °C, 600 °C, but its wear rate is only lower at 300 °C. It is considered that the laser clad NiCr/Cr₃C₂-30%WS₂ composite coating has good combination of anti-wear and friction-reducing capabilities at room-temperature up to 300 °C.     

Laser surface remelting of plasma sprayed nanostructured Al2O3-13wt%TiO2 coatings on titanium alloy

Plasma sprayed nanostructured coatings were successfully fabricated on a titanium alloy (Ti-6Al-4V) substrate using the as-prepared nanostructured Al₂O₃-13wt%TiO₂ feedstock. A CO₂ laser was used to remelt the plasma sprayed coatings. The effects of laser remelting on the phase constituents, microstructure and properties of the ceramic coatings were investigated. The laser remelted coatings (LRmC) possessed a much denser and more homogenous structure and excellent metallurgical bonding to the substrate. The average porosity of the LRmC was reduced to 0.9%, compared with 6.2% of the as-sprayed coatings. The net-like structure in the as-prepared feedstock remained in the coatings before and after laser remelting. The metastable γ-Al₂O₃ phase in the as-sprayed coatings transformed to stable α-Al₂O₃ during laser remelting. The LRmC could remain nanostructure. The microhardness of the coatings was enhanced to 1000-1400 HV_0.3 after laser remelting, which was much higher than that of the plasma sprayed coatings and 2-3 times higher that of the substrate. Significant decreases in surface roughness were also found in the LRmC.     

Study on Fe-Al-Si in situ composite coating fabricated by laser cladding

Fe-Al-Si in situ composite coating was fabricated on the surface of ASTM A283Gr.D steel by laser cladding with the preplaced powder. The influence of powder composition, laser power and scanning speed on microstructure, microhardness and wear resistance were investigated in this paper. The results show that Fe-Al-Si in situ composite coating with the good metallurgical bond mainly consists of Fe, SiO₂ and Al₂Fe₃Si₄ intermetallic compound. With the increase of laser power and scanning speed, the grain size of coating gets the minimum value. With the increase of laser power and scanning speed, microhardness and wear resistance both get the peak vaule, and their value are three times and 3.5 times those of substrate, respectively. The optimum parameters are followed as: the ratio of the preplaced composite powder: 8:1:1, laser power: 1600 W and scanning speed: 400 mm/min.     

Corrosion and wear properties of PEO coatings formed on AM60B alloy in NaAlO2 electrolytes

Coatings with a thickness of 22-32 μm were formed on an AM60B magnesium alloy by plasma electrolytic oxidation (PEO) in electrolytes containing 12.0-24.0 g/l NaAlO₂ and other additives. SEM analyses of the coated samples showed that the coatings were compact with relatively low porosity. X-ray diffraction revealed that the coatings consisted of mainly MgAl₂O₄ and MgO phases. The relative amount of MgAl₂O₄ in the coating increased with increasing NaAlO₂ concentration. The relatively compact and thick coatings provide good corrosion protection for magnesium, as indicated by the results of potentiodynamic polarization tests. In addition, the PEO treatment also significantly improved the wear resistance of the alloy. Pin-on-disk wear tests showed that the PEO treatment reduced the wear volume loss by a factor of 10.     

Microstructure, microhardness and dry friction behavior of cold-sprayed tin bronze coatings

In this paper, two types of tin bronze coatings (Cu-6 wt.% Sn and Cu-8 wt.% Sn) were prepared by cold spray process. The as-sprayed coatings were subjected to a vacuum heat treatment at 600 °C for 3 h. The coating microstructure, microhardness and tribological performance were characterized. The effects of the tin content and the vacuum heat treatment on the microstructure, microhardness and tribological behavior of the coatings were investigated. It is found that the as-sprayed CuSn6 (As6) and CuSn8 (As8) coatings exhibit practically an identical porosity. Meanwhile, As8 presents a higher microhardness than As6. In addition, the increase of the tin content in the powder feedstock leads to a lower wear rate. After a heat treatment, coating porosities are significantly reduced. However, the coating hardness is significantly decreased and the coating presents a much decreased wear resistance. For the as-sprayed coatings, such factors as ploughing and particle delamination could determine the sliding process. The heat treatment results in a distinct modification of the tribological behavior. For the annealed coatings, the adhesion, between the coating and the counterpart, could play a dominant role in the sliding process.     

Microstructure and wear resistance of Fe-based WC coating by multi-track overlapping laser induction hybrid rapid cladding

The carck-free Fe-based +20 wt% WC coating with large area was produced by mutli-track overlapping laser induction hybrid rapid cladding. The results showed that the maximum laser scanning speed and the maximum feeding rate of powder can be increased to 3500 mm/min and 120 g/min, respectively. The cast WC particles were dissolved almost completely and had a worse wettability with Fe-based metal matrix. The precipitated carbides such as M₁₂C and M₂₃C₆ (M=Fe, W, Cr) formed an intergranular network around the primary Fe-based phase enriched with tungsten. The microhardness of coating decreased first, and then increased slightly with an increase in the track. The first track had the highest microhardness (i.e. 870HV_0.2). Moreover, the wear weight of coating approximately had a linear relationship with the sliding distance, and increased with an increase in the sliding speed. The wear rate approximately remained constant with an increase in the sliding distance and was two times lower than that of the hardened steel AISI 1045 with a hardness of 60HRC. The wear mechanism during the dry sliding wear was a combination of oxidation wear and abrasion wear.     

Microstructures and tribological properties of plasma sprayed WC-Co-Cu-BaF2/CaF2 self-lubricating wear resistant coatings

A promising WC-Co-Cu-BaF₂/CaF₂ self-lubricating wear resistant coating was deposited via atmospheric plasma spraying (APS) process by using homemade feedstock powders composed of WC-Co, Cu and BaF₂/CaF₂ eutectic. The as-prepared cermet coatings had better frictional behavior comparing with the WC-Co coating. Moreover, the often-occurred decarburization of WC in APS process was noticeably improved due to the binding of copper and BaF₂/CaF₂ phase, which not only offered effective solid lubrication, but also acted as bind phases to mend the microstructure and protected WC from decomposition. The optimized specimen contained 10 wt.% Cu and 10 wt.% BaF₂/CaF₂ in a WC-Co matrix, which had excellent frictional and wear performance. The wear mechanism of the self-lubricating wear resistant coating was discussed with the microstructures, compositions and mechanical properties of the composite materials in detail.     

Electrodeposition and tribological properties of Ni-SrSO4 composite coatings

Ni-SrSO₄ composite coatings were electrodeposited on superalloy Inconel 718 from a Watts electrolyte containing a SrSO₄ suspension. Ni-SrSO₄ coatings were investigated by scanning electron microscope, microhardness tester, and friction and wear tester in sliding against a bearing steel ball under unlubricated condition. The incorporation of SrSO₄ into Ni matrix increases the microhardness of electrodeposited coatings. Ni-SrSO₄ composite coating exhibits a distinctly low friction coefficient and a small wear rate as contrasted with pure Ni coating and the substrate. The effect of SrSO₄ particles on microstructure and tribological properties of Ni-SrSO₄ composite coatings is discussed.     

Tribological properties of heat-treated electroless Ni-P coatings on AZ91 alloy

Influence of heat treatment regime on adhesion and wear resistance of Ni-P electroless coating on AZ91 magnesium alloy is investigated in this work. The pretreated substrate was plated using a bath containing nickel sulphate, sodium hypophosphite and sodium acetate as main constituents. The coated samples were heat treated at 400-450 °C for 1-8 h. Adhesion of coating was estimated from the scratch test with an initial load of 8.80 N. Wear resistance was studied using the pin-on-disc method. It was found that there is no significant dependence of the coating wear resistance on heat treatment regime, as the formation of Al-Ni intermetallic sub-layers that reduce coating adhesion is limited to regions where Al₁₇Mg₁₂ phase is present in the substrate. Moreover, the coating shows good sliding properties due to the formation of oxide glazes in the wear track.     

Microstructure and wear properties of laser clad Cuss/Cr5Si3 metal silicide composite coatings

Wear resistant Cu-based solid solution (Cu_ss) toughened Cr₅Si₃ metal silicide composite coatings were fabricated on austenitic stainless steel AISI321 by laser cladding process. Due to the rapidly solidified microstructural characteristics and the excellent toughening effect of Cu_ss on Cr₅Si₃, the Cu_ss/Cr₅Si₃ coatings have outstanding wear resistance and low coefficient of friction under room temperature dry sliding wear test conditions coupling with hardened 0.45% C steel.     

Preparation and properties of electroless Ni-P-SiO2 composite coatings

Dispersible SiO₂ nanoparticles were co-deposited with electroless Ni-P coating onto AISI-1045 steel substrates in the absence of any surfactants in plating bath. The resulting Ni-P/nano-SiO₂ composite coatings were heat-treated for 1 h at 200 °C, 400 °C, and 600 °C, respectively. The hardness and wear resistance of the heat-treated composite coatings were measured. Moreover, the structural changes of the composite coatings before and after heat treatment were investigated by means of X-ray diffraction (XRD), while their elemental composition and morphology were analyzed using an energy dispersive spectrometer (EDS) and a scanning electron microscope (SEM). Results show that co-deposited SiO₂ particles contributed to increase the hardness and wear resistance of electroless Ni-P coating, and the composite coating heat-treated at about 400 °C had the maximum hardness and wear resistance.     

Microstructure and mechanical properties of Al2O3-Al composite coatings deposited by plasma spraying

Al₂O₃ and Al₂O₃-Al composite coatings were prepared by plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction (XRD), while optical microscopy (OM) and scanning electron microscopy (SEM) were employed to investigate the morphology of impacted droplets, polished and fractured surface, and the element distribution in terms of wavelength-dispersive spectrometer (WDS). Mechanical properties including microhardness, adhesion and bending strength, fracture toughness and sliding wear rate were evaluated. The results indicated that the addition of Al into Al₂O₃ was beneficial to decrease the splashing of impinging droplets and to increase the deposition efficiency. The Al₂O₃-Al composite coating exhibited homogeneously dispersed pores and the co-sprayed Al particles were considered to be distributed in the splat boundary. Compared with Al₂O₃ coating, the composite coating showed slightly lower hardness, whereas the coexistence of metal Al phase and Al₂O₃ ceramic phase effectively improved the toughness, strength and wear resistance of coatings.