Photoluminescence of thermal-annealed nanocolumnar ZnO thin films grown by electrodeposition

Nanostructured zinc oxide thin films formed by partially oriented hexagonal columns with dimensions of about 100 nm × 300 nm have been prepared by cathodic electrodeposition on conducting glass substrates. After subsequent thermal annealing in air at different temperatures (100-500 °C), structural information on the films was obtained by means of non-resonant Raman spectroscopy. Increasing the annealing temperature leads to a higher degree of crystallinity. The photoluminescence activity of the samples (at low temperature) also improves for increasing annealing temperatures in two ways: increasing the intensity of the near-band edge emission and decreasing the width of the excitonic peak. No emission band in the visible is detected, which attests the high quality of the ZnO nanocolumnar films.     

Seed layer-free synthesis and characterization of vertically grown ZnO nanorod array via the stepwise solution route

A novel stepwise method was developed for the deposition of ZnO nanorod array (NRA) from the simple inorganic aqueous solution. Different from the traditional one-pot synthesis route, merely a thin liquid precursor layer adsorbed on the substrate instead of the bulk solution underwent the reaction at elevated temperature in a typical deposition cycle. Sparse and vertically grown wurtzite ZnO NRA was deposited on seed layer-free glass substrate after 20 cycles (in typically 20 min). Each individual ZnO rod possessed the well-defined hexagonal facet, the side length of about 150 nm, the aspect ratio of 2:3, and the small size dispersity. Also the overall ZnO NRA exhibited high ultraviolet photoluminescence and weak blue emission, indicating its good optical properties. Mechanism analysis indicated that, the decrease of the supersaturation degree in solution after the climax in the reaction period of each deposition cycle is the root cause of the sparse nucleation and the vertical growth of ZnO nanorods. The work has opened up a novel stepwise approach toward high quality ZnO NRA, being valuable for extending the synthetic methods of semiconductor nanostructures in mild solutions.     

Morphology and photoluminescence study of electrodeposited ZnO films

ZnO films on ITO substrates and Au coated ITO substrates were fabricated by using electrodeposition technique. We carried out the experiments by adjusting the concentration of solution, potential, substrate, and temperature. The effect of temperature on the growth of the film has been examined. SEM images have shown that there are several kinds of grown competitions for the deposition of ZnO films, but three kinds of them are dominant. One is the discrete hexagonal column structure, the other is the pentagonal structure, and the third one is of well-oriented hexagonal columns with well-aligned structure. The explanation on the grown competition is discussed. ZnO hexagonal column structures with well-aligned and well-perpendicular to the surface were successfully obtained on Au/ITO substrate in aqueous solvent of electrolyte. Clearly the main columns in the film were obtained by increasing the temperature. Its photoluminescence (PL) study at low temperature exhibited the optical properties as wurtzite ZnO and indicated the existence of macrocrystalline ZnO. A better quality of ZnO columnar structures after annealing was demonstrated from PL analysis and discussion on the existence of 370 nm, 384 nm and 639 nm in the emission bands before and after annealing.     

纳米ZnO微晶的合成及其发光特性

以醋酸锌和尿素为主要原料,利用沉淀-水热法一步合成了纳米ZnO微晶。用XRD,TEM,FTIR等测试技术及光致发光光谱(PL)对纳米ZnO微晶进行了表征,并对其发光特性进行了分析。研究表明：该合成方法操作简单,得到的纳米ZnO颗粒基本无团聚,结晶性较好,平均粒径约为17.2 nm,并在500～750 nm范围内出现宽的PL峰, 呈现出纳米材料的发光特征。     

Effects of annealing on properties of ZnO thin films prepared by electrochemical deposition in chloride medium

The development of cost-effective and low-temperature synthesis techniques for the growth of high-quality zinc oxide thin films is paramount for fabrication of ZnO-based optoelectronic devices, especially ultraviolet (UV)-light-emitting diodes, lasers and detectors. We demonstrate that the properties, especially UV emission, observed at room temperature, of electrodeposited ZnO thin films from chloride medium (at 70 °C) on fluor-doped tin oxide (FTO) substrates is strongly influenced by the post-growth thermal annealing treatments. X-ray diffraction (XRD) measurements show that the films have preferably grown along (0 0 2) direction. Thermal annealing in the temperature range of 150-400 °C in air has been carried out for these ZnO thin films. The as-grown films contain chlorine which is partially removed after annealing at 400 °C. Morphological changes upon annealing are discussed in the light of compositional changes observed in the ZnO crystals that constitute the film. The optical quality of ZnO thin films was improved after post-deposition thermal treatment at 150 °C and 400 °C in our experiments due to the reducing of defects levels and of chlorine content. The transmission and absorption spectra become steeper and the optical bandgap red shifted to the single-crystal value. These findings demonstrate that electrodeposition have potential for the growth of high-quality ZnO thin films with reduced defects for device applications.     

Synthesis and characterization of Mn-doped ZnO column arrays

Mn-doped ZnO column arrays were successfully synthesized by conventional sol-gel process. Effect of Mn/Zn atomic ratio and reaction time were investigated, and the morphology, tropism and optical properties of Mn-doped ZnO column arrays were characterized by SEM, XRD and photoluminescence (PL) spectroscopy. The result shows that a Mn/Zn atomic ratio of 0.1 and growth time of 12 h are the optimal condition for the preparation of densely distributed ZnO column arrays. XRD analysis shows that Mn-doped ZnO column arrays are highly c-axis oriented. As for Mn-doped ZnO column arrays, obvious increase of photoluminescence intensity is observed at the wavelength of ∼395 nm and ∼413 nm, compared to pure ZnO column arrays.     

Growth and characterization of thin ZnO films deposited on glass substrates by electrodeposition technique

Electrodeposition technique was used in order to produce nanometric zinc oxide films on glass insulating substrates. The effect of electrolyte concentration and applied current density on the formation and growth of electrodeposited Zn thin films in aqueous solutions of ZnSO₄ were studied. After a thermal oxidation, a characterization of the structural morphology of the films deposited was carried out by optical microscopy (OM), atomic force microscopy (AFM), scanning electron microscopy (SEM) and by grazing incidence X-rays diffraction (GIXD). These characterization techniques show that the grains size of the films after oxidation at temperature 450 °C is between 5 and 15 nm, as well as the structure is polycrystalline nature with several orientations. UV/vis spectrophotometry confirms that it is possible to obtain transparent good ZnO films with an average transmittance of approximately 80% within the visible wavelength region, as well as the optical gap of obtained ZnO films is 3.17 eV.     

Synthesis of ZnO nanoparticles using nanosecond pulsed laser ablation in aqueous media and their self-assembly towards spindle-like ZnO aggregates

ZnO nanoparticles were fabricated by pulsed laser ablation (PLA) of a Zn metal in aqueous media, and aging effects on the morphology and photoluminescence properties of ZnO nanoparticles were investigated. The crystalline phase and particle morphology were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). It was found that small, well-defined ZnO nanoparticles were obtained by PLA of a Zn plate in aqueous media, and subsequent aging of the obtained ZnO nanoparticle suspension produced in cetyltrimethylammonium bromide (CTAB) solution led to the formation of spindle-like ZnO aggregates. However, in deionized water not the spindle-like ZnO aggregates but fluffy round aggregates were obtained. High-resolution transmission electron microscopic (HRTEM) observation indicated that the spindle-like ZnO aggregates were composed of many well-defined nanoparticles. Spindle-like aggregates exhibited strong exciton emission, while green emission could be suppressed via an aging process in the presence of CTAB. Moreover, thin films prepared by electrophoretic deposition (EPD) of ZnO nanoparticles after PLA in the presence of CTAB also possessed highly elongated aggregate structures that were possibly formed by surrounding the ZnO nanoparticles with double layers of CTAB molecules.     

Synthesis and characterizations of new morphological ZnO and Ce-doped ZnO powders by sol–gel process

ZnO micro-tori and cerium-doped hexangulars ZnO have been prepared by the sol–gel method under methanol hypercritical conditions of temperature and pressure. X-ray diffraction (XRD) measurement has revealed the high crystalline quality and the nanometric size of the samples. Scanning electron microscopy (SEM) has shown that the ZnO powder has a torus-like shape while that of ZnO:Ce has a hexangular-like shape, either standing free or inserted into the cores of ZnO tori. Transmission electron microscopy (TEM) has revealed that the ZnO particles have sizes between 25 and 30 nm while Ce-doped ZnO grains have diameters ranging from 75 nm to 100 nm. It is demonstrated from photoluminescence (PL) spectra at room temperature that the introduction of cerium in ZnO reduces the emission intensity lines, particularly the ZnO red and green ones.     

Controlling growth of ZnO rods by polyvinylpyrrolidone (PVP) and their optical properties

ZnO rods with different morphologies were synthesized through a wet chemical method by addition of polyvinylpyrrolidone (PVP). By adjusting the concentration of the additive in the growth solution, we can control the diameter, ratio of length to diameter and density of ZnO rods. FESEM images showed that the rods in nanoscale could be obtained at the polyvinylpyrrolidone concentration of 1.0 mM. Meanwhile, the resonant Raman scattering and photoluminescence spectra showed that the crystalline quality and the optical property of ZnO rods were improved through moderate addition of polyvinylpyrrolidone (concentration of 1.0 mM) in the growth solution. In addition, the possible mechanism of the PVP effect on the growth of ZnO rods was discussed based on the FT-IR spectra.     

硫掺杂ZnO纳米线的电化学制备及发光特性

"采用电场辅助电化学沉积法,利用阳极氧化铝模板模板制备了高度择优取向的硫掺杂ZnO单晶纳米线．X射线衍射仪、隧道电子显微镜、选取电子衍射对所得样品的结构、形貌分析表明,所得纳米线是沿(101)择优取向的六方纤锌矿结构单晶纳米线,长约几十微米、平均直径约70 nm. X射线光电子能谱对化学组成的分析进一步证实掺杂硫原子的存在．用荧光光谱仪(PL)对S掺杂前后的ZnO纳米线进行光学特性测量发现,S掺杂较大地改变了ZnO纳米线的发光性质．在PL谱中,除了有典型的ZnO纳米线在378、392 nm处的强紫外发光峰     

Quantum dot light emitting diodes using size-controlled ZnO NPs

The particle size and trap energy level of ZnO were adjusted by varying the concentration of precursors using a sol–gel process, and the energy transport properties of the electron transport layer in quantum dot light-emitting diodes (QD-LEDs) were analyzed. Thus far, no study has considered the efficient electron transport properties of quantum dot light-emitting devices with respect to trap energy levels owing to the oxygen vacancies of ZnO. The particle size and trap energy levels of ZnO were analyzed based on optical properties such as photoluminescence and absorbance. The optimized device showed excellent performance, with a maximum luminance of 50,120 cd/m², a high efficiency of 5.85 cd/A, and a threshold voltage of 2.5 V. The Y-ZnO (yellow photoluminescence ZnO)-based QD-LEDs not only enhanced the injection efficiency of electrons into the emitting layer but also confined the holes in the emitting layer due to the shallow trap level of Y-ZnO, in contrast to the deep trap levels of G-ZnO (green photoluminescence ZnO) and B-ZnO (blue photoluminescence ZnO). Here, we present the first attempt to analyze the electron transport behavior of the electron transport layer of the resulting device.     

Photoluminescence properties of various CVD-grown ZnO nanostructures

We have studied systematically room-temperature photoluminescence (PL) properties of many nanostructured ZnO samples grown by chemical vapour deposition (CVD). Their PL spectra consist of two emissions peaked in the ultraviolet (UV) and green regions. The relative intensity of these emissions depends on the excitation energy density, size and morphology of ZnO nanostructures. Based on the excitation-density dependence of the integrated intensity ratio of UV-to-green emission, we could classify PL spectra of ZnO nanostructures into three groups characteristic of size and morphology. Our study also reveals that with increasing excitation density, the UV-peak position shifts slightly towards longer wavelengths while the green emission around 514-520 nm is almost unchanged. This green-luminescence emission is dominant when the nanostructure sizes range from 20 to 200 nm, which is related to a large surface-to-volume ratio.     

Structural, optical and magnetic properties of Cr doped ZnO microrods prepared by spray pyrolysis method

A series of Cr-doped ZnO micro-rod arrays were fabricated by a spray pyrolysis method. X-ray diffraction patterns of the samples showed that the undoped and Cr-doped ZnO microrods exhibit hexagonal crystal structure. Surface morphology analysis of the samples has revealed that pure ZnO sample has a hexagonal microrod morphology. From X-ray photoelectron spectroscopy studies, the Cr 2p3/2 binding energy is found to be 577.3 eV indicating that the electron binding energy of the Cr in ZnO is almost the same as the binding energy of Cr³⁺ states in Cr₂O₃. The optical band gap E_g decreases slightly from 3.26 to 3.15 eV with the increase of actual Cr molar fraction from x = 0.00 to 0.046 in ZnO. Photoluminescence studies at 10 K show that the incorporation of chromium leads to a relative increase of deep level band intensity. It was also observed that Cr doped samples clearly showed ferromagnetic behavior; however, 2.5 at.% Cr doped ZnO showed remnant magnetization higher than that of 1.1 at.% and 4.6 at.% Cr doped samples, while 4.6 at.% Cr doped ZnO samples had a coercive field higher than the other dopings.     

Growth and optical properties of ZnO microwells by chemical vapor deposition method

The well-like ZnO nanostructures were obtained by chemical vapor deposition method. The uniform and dense ZnO slim nano-columns were grown along the circle to form a microwell. The growth mechanisms, such as 1D linear, 2D screw dislocation and step growth are discussed. These observations provide some insight into the growth kinetics in vapor-solid growth process. The fabrication of ZnO microwell morphology provided a direct experimental evidence for explaining the 1D growth mechanism based on the axial screw dislocation. Photoluminescence (PL) microscopy showed the surface-related optical properties. The green light emission enhancement revealed that the ZnO microwells have waveguide properties. The abnormal enhancement of integrated PL intensity of deep-level emission with temperature increase showed abundant surface state existence.     

Synthesis and properties of boron doped ZnO nanorods on silicon substrate by low-temperature hydrothermal reaction

Boron doped ZnO nanorods were fabricated by hydrothermal technique on silicon substrate covered with a ZnO seed layer. It is found that the concentration of boric acid in the reaction solution plays a key role in varying the morphology and properties of the products. The growth rate along the [0 0 0 1] orientation (average size in diameter) of the doped ZnO nanorods decreased (increased) with the increase of boric acid concentration. Based on the results of XRD, EDX and XPS, it is demonstrated that the boron dopants tend to occupy the octahedral interstice sites. The photoluminescence of the ZnO nanorods related to boron doping are investigated.     

Synthesis of transparent ZnO/PMMA nanocomposite films through free-radical copolymerization of asymmetric zinc methacrylate acetate and in-situ thermal decomposition

In this paper, a new and simple approach for in-situ preparation of transparent ZnO/poly(metyl methacrylate) (ZnO/PMMA) nanocomposite films was developed. Poly(methyl methacrylate)-co-poly(zinc methacrylate acetate) (PMMA-co-PZnMAAc) copolymer was synthesized via free-radical polymerization between methyl methacrylate (MMA) and zinc methacrylate acetate (ZnMAAc), where asymmetric ZnMAAc with only one terminal double bond (C=C) was applied to act as the precursor for ZnO nanocrystals and could avoid cross-link. Subsequently, transparent ZnO/PMMA nanocomposite films were obtained by in-situ thermal decomposition. Scanning electron microscope (SEM) image revealed that ZnO nanocrystals were homogeneously dispersed in PMMA matrix. With thermal decomposition time increasing, the absorption intensity in UV region and photoluminescence intensity of ZnO/PMMA nanocomposite films enhanced. However, the optical properties diminished when the thermal decomposition temperature increased. The TGA measurement displayed ZnO/PMMA nanocomposite films prepared by the in-situ synthesis method possessed better thermal stability compared with those prepared by the physical blending method and pristine PMMA films.     

Photoluminescence study of hydrogen donors in ZnO

A photoluminescence study of hydrogenated ZnO bulk crystals is presented. Two excitonic recombination lines at 3362.8 and 3360.1 meV are assigned to hydrogen shallow donors. Experimental evidence is presented that the corresponding donor to the line at 3362.8 meV, previously labeled I₄, originates from hydrogen trapped within the oxygen vacancy, H_O. The line at 3360.1 meV was found to be due to hydrogen located at the bond-centered lattice site, H_BC. The corresponding shallow donor has an ionization energy of 53 meV.     

Photo and electroluminescence of ZnO : Er and ZnO : Ag,Er electroluminors

A number of ZnO : Er and ZnO : Ag, Er electroluminors have been prepared and their photo (PL) and electroluminescent (EL) properties investigated. While the addition of Ag slightly shifts the PL spectra towards longer wavelength side, the EL spectra not only shift but consist of some new transitions. In ZnO : Er electroluminors, additional transitions also exist at higher frequencies of excitations. Brightness waves for this system consist of two secondary peaks during each half cycle of exciting field. Temperature dependence shows two broad peaks. While voltage dependence of ZnO : Er satisfies the relationB=B ₀ exp(−b/V ^1/2), the relationB=B ₀ V exp(−b/V ^1/2) is found to be suitable for ZnO : Ag, Er electroluminor. Possible mechanisms for these phenomena have been proposed. A preliminary account of this work was presented at the International Symposium on Solid State Physics held at the Indian Association for the Cultivation of Science, Calcutta in January 1977.