TSL, OSL and ESR studies in ZnAl2O4:Tb phosphor

ZnAl₂O₄:Tb phosphor was prepared by combustion synthesis. ZnAl₂O₄:Tb exhibits three thermally stimulated luminescence (TSL) peaks around 150, 275 and 350 °C. ZnAl₂O₄:Tb exhibits optically stimulated luminescence (OSL) when stimulated with 470 nm light.Electron spin resonance (ESR) studies were carried out to identify defect centres responsible for TSL peaks observed in ZnAl₂O₄:Tb. Two defect centres are identified in irradiated ZnAl₂O₄:Tb phosphor and these centres are assigned to V and F⁺ centres. V centre appears to correlate with the 150 °C TSL peak, while F⁺ centre could not be associated with the observed TSL peaks.     

Superacid Catalyst SO42-/ZrO2-La2O3 Prepared by Ultrasonic Co-precipitation and Low Temperature Aging

低温陈化超声波共沉淀法制得SO₄^2-/ZrO^2-La₂O₃前驱体, 经H₂SO₄处理, 在不同温度下焙烧得到纳米晶催化剂SO₄^2-/ZrO^2-La₂O₃;用Hammett指示剂法测定其酸性. 用XRD、BET、TEM、IR和XPS对样品进行表征,其催化活性用醋酸和甘油的酯化反应进行了评价. 结果表明经超声波搅拌和低温(-15 ºC)陈化,650 ºC焙烧4 h得到的固体超强酸表现出较高催化活性.     

Mechanism of amorphous Ge2Sb2Te5 removal during chemical mechanical planarization in acidic H2O2 slurry

In this paper, chemical mechanical planarization (CMP) of amorphous Ge2Sb2Te5 (a-GST) in acidic H2O2 slurry is investigated. It was found that the removal rate of a-GST is strongly dependent on H2O2 concentration and gradually increases with the increase in H2O2 concentration, but the static etch rate first increases and then slowly decreases with the increase in H2O2 concentration. To understand the chemical reaction behavior of H2O2 on the a-GST surface, the potentiodynamic polarization curve, surface morphology and cross-section of a-GST immersed in acidic slurry are measured and the results reveal that a-GST exhibits a from active to passive behavior for from low to high concentration of H2O2 . Finally, a possible removal mechanism of a-GST in different concentrations of H2O2 in the acidic slurry is described.     

Effects of CeO2-ZrO2 present in Pd/Al2O3 catalysts on the redox behavior of PdOx and their combustion activity

The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H₂PdCl₄ as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H₂-TPR) and temperature programmed oxidation (O₂-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al₂O₃-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO₂-ZrO₂ on the Ce-Zr/Al₂O₃ surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al₂O₃-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al₂O₃ catalyst would inhibit the site growth of PdO_x particles and decomposition of PdO to Pd⁰, and the reoxidation property of Pd⁰ to PdO_x is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al₂O₃ catalyst for the methane combustion.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Comparative analysis of crystal field effects and energy level scheme of six-fold coordinated Cr ion in the pyrochlores, Y2B2O7 (B=Ti, Sn)

The electronic energy levels of the six-fold coordinated Cr⁴⁺ ion in the pyrochlores Y₂B₂O₇ (B=Sn⁴⁺, Ti⁴⁺), have been computed using the exchange charge model of crystal field theory. The calculated Cr⁴⁺ energy levels and their trigonal splitting are in good agreement with experimental spectra. Calculations of the crystal field parameters show that the higher crystal field strength in Y₂Sn₂O₇ (in comparison with Y₂Ti₂O₇) arises from increased orbital overlap effects between the Cr⁴⁺ ion and the nearest oxygen ions, which are located at the 48f crystallographic position of the pyrochlore lattice. The increased overlap in Y₂Sn₂O₇ occurs despite the fact that the Cr⁴⁺-O^2- bond distance in Y₂Sn₂O₇ is longer than in Y₂Ti₂O₇. This is attributed to a lack of hybridization (covalent bonding) between the filled 2p orbital of oxygen ion occupying the 48f site of the pyrochlore lattice and the filled Sn⁴⁺ 4d¹⁰ orbital. As a result, a stronger crystal field is experienced by Cr⁴⁺ ions in Y₂Sn₂O₇, even if the Cr⁴⁺-O²⁻ distances are greater in this case, when compared to those in Y₂Ti₂O₇.     

闭壳层金掺杂钛氧团簇阴离子解离氢分子研究

Dissociation of molecular hydrogen (H₂) is extensively studied to understand the mechanism of hydrogenation reactions. In this study, H₂ dissociation by Au₁-doped closed-shell titanium oxide cluster anions AuTi₃O₇^- and AuTi₃O₈^- has been identified by mass spectrometry and quantum chemistry calculations. The clusters were generated by laser ablation and massselected to react with H₂ in an ion trap reactor. In the reaction of AuTi₃O₈^- with H₂, the ion pair Au⁺-O₂^2- rather than Au⁺-O^2- is the active site to promote H₂ dissociation. This finding is in contrast with the previous result that the lattice oxygen is usually the reactive oxygen species in H₂ dissociation. The higher reactivity of the peroxide species is further supported by frontier molecular orbital analysis. This study provides new insights into gold catalysis involving H₂ activation and dissociation.     

A facile synthesis of monodisperse CoFe2O4/SiO2 nanoparticles

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. By optimizing the preparation conditions, monodisperse CoFe₂O₄/SiO₂ NPs with high amino groups’ density were obtained, which is necessary for enzyme immobilization. TEM confirm that the sample is a core/shell structure. These aminated-CoFe₂O₄/SiO₂ NPs have narrow size distributions with a mean size of about 60 nm. Moreover, the aminated-CoFe₂O₄/SiO₂ NPs can be easily dispersed in aqueous medium. The experimental results also show that the NPs have superparamagnetism, indicating that the aminated-CoFe₂O₄/SiO₂ NPs can be used as an effective carrier for the enzyme immobilization.     

The role of copper species on Cu/γ-Al2O3 catalysts for NH3-SCO reaction

UV-vis spectra, XRD, H₂-TPR, TEM and ESR were used to characterize a series of Cu/γ-Al₂O₃ catalysts, which were prepared by incipient wetness impregnation using copper nitrate, copper acetate or copper sulfate as precursors, to study the role of Cu species on Cu/γ-Al₂O₃ catalysts for NH₃-SCO reaction. It was found that the mixture of CuO phase and CuAl₂O₄ phase formed on various Cu/γ-Al₂O₃ catalysts, and the Cu species and dispersion had significant influence on the Cu/γ-Al₂O₃ activity. Highly dispersed CuO phase on the support would be related with its high activity for the NH₃-SCO reaction.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

The effect of Si surface nitridation on the interfacial structure and electrical properties of (La2O3)0.5(SiO2)0.5 high-k gate dielectric films

Thermal stability, interfacial structures and electrical properties of amorphous (La₂O₃)_0.5(SiO₂)_0.5 (LSO) films deposited by using pulsed laser deposition (PLD) on Si (1 0 0) and NH₃ nitrided Si (1 0 0) substrates were comparatively investigated. The LSO films keep the amorphous state up to a high annealing temperature of 900 °C. HRTEM observations and XPS analyses showed that the surface nitridation of silicon wafer using NH₃ can result in the formation of the passivation layer, which effectively suppresses the excessive growth of the interfacial layer between LSO film and silicon wafer after high-temperature annealing process. The Pt/LSO/nitrided Si capacitors annealed at high temperature exhibit smaller CET and EOT, a less flatband voltage shift, a negligible hysteresis loop, a smaller equivalent dielectric charge density, and a much lower gate leakage current density as compared with that of the Pt/LSO/Si capacitors without Si surface nitridation.     

Response improvement for In2O3-TiO2 thick film gas sensors

In₂O₃ is introduced into TiO₂ by sol-gel method to improve the response/recovery rate and expand the operating temperature, when the In₂O₃-TiO₂ mixed system is exposed to H₂/O₂. The sensor is fabricated by thick film technology. Influence of In₂O₃ on the film phase composition, microstructure and sensing characteristics is discussed. Dynamic response properties show that the operating temperature of the mixed system is at 500-800 °C, which is about 600-800 °C for pure TiO₂. Response time of the sensor is about 200-260 ms (millisecond) while recovery time is in a narrow range of 60-280 ms at 600-800 °C. The promoting mechanism is suggested to arise from the introduction of In₂O₃ and grain size effect of the sensing film. Then In₂O₃-TiO₂ thick films are surface-modified by Pt using chloroplatinic acid. The promoting effect of Pt dispersed on the mixed system is also investigated.     

MoO3/Al2O3催化剂中Mo分散的正电子研究

用浸渍法制备了一系列不同Mo含量的MoO₃/Al₂O₃催化剂.测量了这些样品的正电子湮没寿命谱(PALS)与符合多普勒展宽(CDB)谱,以研究其孔洞结构以及Mo分散.正电子寿命测量结果表明,Al₂O₃载体中存在两种不同尺寸的孔洞.掺入MoO₃之后,Mo原子主要进入Al₂O₃的大孔中,使孔洞体积减小.符合多普勒展宽谱结果表明,当MoO 关键词： 3/Al₂O₃催化剂')" href="#">MoO₃/Al₂O₃催化剂 正电子湮没寿命谱 符合多普勒展宽 Mo 分散     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

Conductivity and water uptake of Sr4(Sr2Nb2)O11·nH2O and Sr4(Sr2Ta2)O11·nH2O

The hydrated oxygen deficient complex perovskite-related materials Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O were studied at high water vapour pressures over a large temperature range by electrical conductivity measurements, thermogravimetry (TG), and X-ray powder diffraction (XRPD). In humid atmospheres both materials are known to exhibit protonic conductivity below dehydration temperatures, with peak-shaped maxima at about 500 °C. In this work we show that the peaks expand to plateaus of high conductivity from 500 to 700 °C at a water vapour pressure of 1 atm. However, in situ synchrotron XRPD of Sr₄(Sr₂Nb₂)O₁₁·nH₂O as a function of temperature shows that these observations are in fact coincident with melting and dehydration of a secondary phase Sr(OH)₂. The stability of Sr₄(Sr₂Nb₂)O₁₁·nH₂O and Sr₄(Sr₂Ta₂)O₁₁·nH₂O in humid atmospheres is thus insufficient, causing decomposition into perovskites with lower Sr content and SrO/Sr(OH)₂ secondary phases. This, in turn, rationalizes the observation of peaks and plateaus in the conductivity of these materials.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Experimental and kinetic modeling study of C2H4 oxidation at high pressure

A detailed chemical kinetic model for oxidation of C₂H₄ in the intermediate temperature range and high pressure has been developed and validated experimentally. New ab initio calculations and RRKM analysis of the important C₂H₃ + O₂ reaction was used to obtain rate coefficients over a wide range of conditions (0.003-100 bar, 200-3000 K). The results indicate that at 60 bar and medium temperatures vinyl peroxide, rather than CH₂O and HCO, is the dominant product. The experiments, involving C₂H₄/O₂ mixtures diluted in N₂, were carried out in a high pressure flow reactor at 600-900 K and 60 bar, varying the reaction stoichiometry from very lean to fuel-rich conditions. Model predictions are generally satisfactory. The governing reaction mechanisms are outlined based on calculations with the kinetic model. Under the investigated conditions the oxidation pathways for C₂H₄ are more complex than those prevailing at higher temperatures and lower pressures. The major differences are the importance of the hydroxyethyl (CH₂CH₂OH) and 2-hydroperoxyethyl (CH₂CH₂OOH) radicals, formed from addition of OH and HO₂ to C₂H₄, and vinyl peroxide, formed from C₂H₃ + O₂. Hydroxyethyl is oxidized through the peroxide HOCH₂CH₂OO (lean conditions) or through ethenol (low O₂ concentration), while 2-hydroperoxyethyl is converted through oxirane.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺