Influence of the substrate hydrophilicity on the grid assisted deposition of tris-(8-hydroxyquinolinato) aluminum(III) thin films

The influence of the substrate wetting properties on the grid assisted deposition of tris-(8-hydroxyquinolinato)aluminum(III) (Alq₃) onto Si/SiO_x surfaces was investigated. Different degrees of hydrophilicity/hydrophobicity on the Si/SiO_x were obtained by changing the surface chemical functionalities with wet treatments. We observed that the deposited Alq₃ films can be spatially controlled and assembled either into continuous grid-like stripes or ordered dots depending upon the wetting properties of the substrate.     

The role of copper ions on the structural and magnetic characteristics of MgZn ferrite nanoparticles and thin films

In this study Cu_xMg_0.5−xZn_0.5Fe₂O₄ (x=0-0.5) nanoparticles and thin films were prepared by sol-gel processing. The morphologies of nanoparticles were observed by transmission electron microscope (TEM). The Mössbauer spectroscopy (MS) was employed to determine the site preference of the constitutive elements. Magnetic dynamics of the nanoparticles was studied by the measurement of AC magnetic susceptibility versus temperature at different frequencies. The phenomenological Néel-Brown and Vogel-Fulcher models were employed to distinguish between interacting or non-interacting system. Results exhibited that there is strong interaction between fine particles. X-ray diffraction (XRD) patterns of the thin films indicate the formation of single-phase cubic spinel structure. Atomic force microscope (AFM) was employed to evaluate the surface morphologies of the prepared thin films. Vibrating sample magnetometer (VSM) was employed to probe magnetic properties of samples. It was found that with an increase in the amount of copper, the saturation of magnetization and initial permeability increase.     

Deposition of potassium-oxygen on silicon surfaces by pulsed laser ablation of potassium superoxide: Study of work function changes

Potassium-oxygen species were deposited on pure, Si nanoparticles coated and H-terminated Si nanoparticles coated p-Si(1 0 0) surfaces by pulsed laser ablation of potassium superoxide (KO₂) target. The deposition properties, composition and the work function changes of the deposited species were investigated in situ using an X-ray photoelectron spectroscopy (XPS) and a Kelvin probe measurement. The deposited species were assigned to K₂O₂ and KO₂, and they can be selectively deposited by controlling the laser fluence: i.e., at 200 mJ/cm² and at those more than 300 mJ/cm², respectively. Experimental results showed that the work function decreased drastically with depositing of KO_x (x = 1 or 2), and the minimum work function values observed were 1.0 eV and 0.7 eV for pure p-Si(1 0 0) and Si nanoparticles coated substrates, respectively. The study demonstrates the formation of the surface species with minimum work function can be identified by XPS.     

Low toxic and highly luminescent CdSe/Cd<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Zn<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>S quantum dots with thin organic SiO<Subscript>2</Subscript> coating for application in cell imaging

A silanization process was employed to transfer hydrophobic quantum dots (QDs) prepared via an organic route at high temperature into water phase. The QDs were further coated with a thin organic SiO₂ shell to form QDs@SiO₂ composite nanoparticles by ligand exchange or remaining initial organic ligands on the surface. In this study, QDs with different ligands, either trioctylphosphine oxide (TOPO) or oleic acid (OA), were employed to investigate the effects of ligands on the reverse micelles in preparing QDs@SiO₂ nanoparticles. In the preparing process, hydrophobic QDs were silanized by partially hydrolyzed tetraethyl orthosilicate (TEOS). For TOPO-capped CdSe QDs, surface TOPO ligands were completely replaced by partially hydrolyzed TEOS. As for OA-capped CdSe/Cd _x Zn_1?x S QDs, surface OA ligands were partially replaced. It was found that the ligand exchange drastically reduced the photoluminescence (PL) efficiency of CdSe QDs. Furthermore, the cytotoxicity studies of QDs@SiO₂ have been carried out in detail. The results indicate that CdSe/Cd _x Zn_1?x S QDs@SiO₂ composite nanoparticles exhibit lower cytotoxicity compared with CdSe QDs@SiO₂, because the SiO₂ shell and remained OA ligand layer can effectively prevent the leakage of toxic Cd²⁺ ions. Meanwhile, it was found that these CdSe/Cd _x Zn_1?x S QDs@SiO₂ nanocomposites could keep excellent PL properties even for 24 h incubating with Siha cells, which indicating that our prepared composite nanoparticles are potentially applicable for cell imaging in biological systems.     

Tailoring Cu2−xTe quantum-dot-decorated ZnO nanoparticles for potential solar cell applications

Cu_2−xTe QDs on ZnO nanoparticles were synthesized using a successive ionic layer absorption and reaction technique (SILAR) at room temperature. The as-synthesized QDs which were distributively deposited on ZnO nanoparticles surface were characterized by field emission scanning electron microscope (FE-SEM), X-ray diffraction and high-resolution transmittance microscope (HR-TEM). It revealed that the average diameter of the QDs was ∼2 nm. The synthesized Cu_2−xTe QDs were solely orthorhombic Cu_1.44Te phase. The growth mechanism was supposed that it based on ions deposition. The energy gap of as-synthesized Cu_2−xTe QDs was determined ∼1.1 eV and the smallest energy gap of 0.76 eV was obtained, equal to that of bulk material. Raman spectroscopy and FTIR were also used to study the Cu_2−xTe QDs on ZnO nanoparticles. These characteristics suggest a promising implication for a potential broadband sensitizer of QDSCs.     

Desorption of surfactant and sintering of surface-modified PdxNi1 − x nanoparticles

A series of Pd_xNi_1 − x nanoparticles in a diameter of 6-7 nm were prepared by wet chemical reduction. They were then modified with two surfactants, stearic acid (SA) and polyethylene glycol (PEG). Desorption of the surfactant was studied using a temperature programmed desorption technique, and the sintering behavior of surface-modified Pd_xNi_1 − x nanoparticles was examined. Since surface energy of the nanoparticles depends on the alloy composition, it can be correlated with the desorption temperature of surfactant from the nanoparticle surface. Because Ni has a higher surface energy, the surfactant desorption temperature increases as the Ni content increases. With the same stoichiometry, the desorption temperature of SA is always higher than that of PEG. The SA-modified nanoparticles have higher thermal stability and are less sintered than PEG-modified nanoparticles. The sintering and growth behavior of the nanoparticles can be correlated with variation of surface energy due to different surface modification.     

X-ray photoelectron spectroscopic studies of black silicon for solar cell

The black silicon has been produced by plasma immersion ion implantation (PIII) process. The microstructure and optical reflectance are characterized by field emission scanning electron microscope and spectrophotometer. Results show that the black silicon appears porous or needle-like microstructure with the average reflectance of 4.87% and 2.12%, respectively. The surface state is investigated by X-ray photoelectron spectroscopy (XPS) technique. The surface of the black silicon is composed of silicon, carbon, oxygen and fluorine element. The formation of Si_xO_yF_z in the surface of black silicon can be proved clearly by the O 1s, F 1s and Si 2p XPS spectra. The formation mechanism of the black silicon produced by PIII process can be obtained from XPS results. The porous or needle-like structure of the black silicon will be formed under the competition of SF_x⁺ (x ≤ 5) and F⁺ ions etching effect, Si_xO_yF_z passivation and ion bombardment.     

Fabrication of superhydrophobic surfaces based on ZnO-PDMS nanocomposite coatings and study of its wetting behaviour

Superhydrophobic surfaces based on ZnO-PDMS nanocomposite coatings are demonstrated by a simple, facile, time-saving, wet chemical route. ZnO nanopowders with average particle size of 14 nm were synthesized by a low temperature solution combustion method. Powder X-ray diffraction results confirm that the nanopowders exhibit hexagonal wurtzite structure and belong to space group P63mc. Field emission scanning electron micrographs reveal that the nanoparticles are connected to each other to make large network systems consisting of hierarchical structure. The as formed ZnO coating exhibits wetting behaviour with Water Contact Angle (WCA) of ∼108°, however on modification with polydimethylsiloxane (PDMS), it transforms to superhydrophobic surface with measured contact and sliding angles for water at 155° and less than 5° respectively. The surface properties such as surface free energy (γ_p), interfacial free energy (γ_pw), and the adhesive work (W_pw) were evaluated. Electron paramagnetic resonance (EPR) studies on superhydrophobic coatings revealed that the surface defects play a major role on the wetting behaviour. Advantages of the present method include the cheap and fluorine-free raw materials, environmentally benign solvents, and feasibility for applying on large area of different substrates.     

Magnetic and dielectric properties of alkaline earth Ca and Ba ions co-doped BiFeO3 nanoparticles

Ca²⁺ and Ba²⁺ ions co-doped BiFeO₃ nanoparticles, Bi_0.8Ca_0.2−xBa_xFeO₃ (x=0-0.20), were prepared by a sol-gel method. The phase structure, grain size, dielectric and magnetic properties of the prepared samples were investigated. The results showed that the lattice structure of the nanoparticles transformed from rhombohedral (x=0) to orthorhombic (x=0.07-0.19) and then to tetragonal (x=0.20) with x increased. The dielectric properties of the nanoparticles were affected by the properties of the substitutional ions as well as the crystalline structure of the samples. The magnetic properties of the nanoparticles were greatly improved and the T_N of the nanoparticles was obviously increased. All the Ca²⁺ and Ba²⁺ ions co-doped BiFeO₃ nanoparticles presented the high ratio of M_r/M from 0.527 to 0.571 and large coercivity from 4.335 to 5.163 KOe.     

Temperature-programmed surface reaction (TPSR) of CH4 synthesis by PdxNi100−x nanoparticles

A series of Pd_xNi_100−x nanoparticles were prepared by the co-precipitation method and analyzed using a temperature-programmed surface reaction (TPSR) of their methanation reactions. ESCA measurement suggested that the as-prepared Pd-Ni alloys had Pd-core/Ni-shell structure. Surface Pd segregation occurred during H₂ reduction and resulted in a surface composition close to the nominal value. The TPSR experiments were performed by pre-adsorption of CO with H₂ to form methane. The peak temperature of methanation increased as Pd content increased, indicating that a methanation reaction is favored on Ni and Ni-rich alloy nanoparticles. For physical mixtures of Pd and Ni nanoparticles, methanation behaviors is similar to those of alloy nanoparticles; but the methanation temperatures of physical mixtures are always higher than those of alloy nanoparticles. This may be due to the formation of a Pd-enriched alloy surface layer during reduction in H₂ at 400 °C, or because the CO molecules adsorbed on the Pd sites spill over onto the Ni sites for methanation. Using TPSR technique and measuring methanation temperature, the top-most surface of such bimetallic nanoparticles can be probed.     

Improving mechanical properties of a-CNx films by Ti-TiN/CNx gradient multilayer

Amorphous carbon nitride (a-CN_x) films with functional gradient Ti-TiN/CN_x underlayer were deposited by direct current magnetron sputtering. Microstructure and composition of the films were characterized by means of X-ray diffraction (XRD), Raman spectroscopy, atomic force microscope (AFM) and transmission electron microscopy (TEM). Mechanical and tribological properties were investigated by nanoindenter, scratch and ball-on-disk tribometer. The a-CN_x-based films suffer a graphitization process with the increasing deposition temperature, thus the hardness and elastic modulus decrease. With the design of the Ti-TiN/CN_x gradient underlayers, some important advantages of relatively thick CN_x films can be achieved, such as increased hardness, improved adhesion strength, and the wear resistance of the a-CN_x-based films can be also improved significantly.     

Fabrication of BixPdy bimetallic materials characterized by catalytic activity at low temperature: Nitro reduction and Suzuki−Miyaura coupling reactions under green conditions

A simple method for synthesizing the Bi_xPd_y bimetallic particles is described. The structure, composition distribution and size of synthesized Bi_xPd_y bimetallic particles were characterized using a number of analytical techniques. The Bi:Pd atomic ratio (x:y) of the nanoparticles was determined to be approximately 1:3 (Bi₂₄Pd₇₆), 1:1 (Bi₅₄Pd₄₆) and 3:1 (Bi₇₄Pd₂₆). The (111) diffraction peaks within the X-ray diffraction patterns of the bimetallic nanoparticles shifted from 39.9° to 38.5° as the Bi content increased from 0% to 75%. The d-spacings calculated from the 2θ data of (111) planes were 2.33, 2.34, 2.32 and 2.26 nm for nanoparticles with a Bi:Pd atomic ratio of 3:1, 1:1, 1:3 and 0:1 respectively. The crystalline properties of the surface of the Bi_xPd_y bimetallic nanoparticles were observed in high-resolution transmission electron microscopy analysis. The d-spacings between the adjacent lattice planes were measured on the surface of Bi_xPd_y bimetallic nanoparticles by averaging 10 lattice fringes distance. A regular face-centered cubic lattice was observed throughout the prepared Bi_xPd_y bimetallic nanoparticles. The lattice d-spacing of the Bi₃Pd₁, Bi₁Pd₁ and Bi₁Pd₃, bimetallic nanoparticles was approximately 2.34, 2.33 and 2.32 Å, respectively, which can be indexed to the (111) planes. These measurements correspond to the values calculated using the Bragg equation (d = nλ/2sinθ). The catalytic activity of Bi_xPd_y bimetallic nanoparticles was determined for the nitro compound reduction and Suzuki-Miyaura coupling reactions under green conditions (in an aqueous solution). Bi₁Pd₃ nanoparticles were shown to provide the best catalytic performance during both reactions, resulting in a yield of 98% in both cases.     

Growth of single-walled carbon nanotubes on silicon nanowires

Single-walled carbon nanotubes (SWNTs) have been grown on silicon nanowires (SiNWs) by ethanol chemical vapor deposition (CVD) with Co catalysts. We have found that a surface SiO_x layer of SiNWs is necessary for the formation of active Co catalysts. In fact, the yield of the SWNT/SiNW heterojunctions gradually decreases as the thickness of the surface SiO_x layer decreases. Since thin SiNWs are transparent to an electron beam, the Co nanoparticles on SiNWs can be easily observed as well as SWNTs by TEM. Therefore, the relationship between the diameters of each SWNT and its catalyst nanoparticle has been investigated. The diameters of SWNTs are equal to or slightly smaller than those of the catalyst nanoparticles.     

Au-MoOx nanoparticles for LSPR hydrogen detection prepared by a facile anodizing method

Nowadays, the plasmonic properties of defective transition metal oxides, have attracted great attention in the sensing and catalyst applications. The aim of this paper is to fabricate plasmonic Au-MoO_x nanoparticles (NPs) using a facile anodizing in liquid approach to be used as localized surface plasmon resonance (LSPR) hydrogen sensor. Firstly, dark blue MoO_x nanosheets with a strong NIR (700–800 nm) LSPR band were obtained. The Au-MoO_x NPs (Au size=5–7 nm) were then obtained by adding a gold cation into the blue MoO_x liquid base. Thanks to the catalytic properties of Au NP, this system exhibited LSPR hydrogen sensing ability where the LSPR variations allowed us to detect hydrogen in the 0–3% concentration range with a good linearity and possible many data points.     

Magnetic properties of Bi-doped Y3Fe5O12 nanoparticles

Bi³⁺ substituted garnet nanoparticles Y_3−xBi_xFe₅O₁₂ (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2 and 1.3) were fabricated by a sol–gel method and their crystalline structures and magnetic properties were investigated by using X-ray diffraction (XRD), IR spectroscopy, thermal gravity analysis–differential thermal analysis (TG-DTA), transmission electron microscope (TEM), Mössbauer spectroscopy and vibrating sample magnetometer (VSM). The XRD patterns of Y_3−xBi_xFe₅O₁₂ have only peaks of the garnet structure. From the results of VSM, it is shown that the saturation magnetization of sample is decreased with increasing the content of Bi ions. Meanwhile, it is observed that with the enhancement of the single magnetic domains surface spin effects, the saturation magnetization is raised as the particle size of samples is increased.     

Co x Ag1−x core–shell nanoparticles: magnetic and magneto-optical studies

The magneto-optical properties of 14-nm Co _x Ag_1?x core–shell nanoparticles (x=0.7, 0.8, and 0.35) deposited on different substrates are investigated at room temperature in the photon-energy range from 0.8 to 4.8 eV. Particles with low Ag content show spectra very similar to pure Co nanoparticles while particles with high Ag content have totally different features, where the Ag plasma edge dominates the spectra. The spectral features of the polar Kerr rotation depend on particle composition. The ageing process and development of an oxide layer influence the particles’ core–shell structures and magnetization curves. Co-rich particles exhibit lower resistance to the oxidation process as compared to Ag-rich ones. The quality of the nanoparticles was checked by transmission electron microscopy in respect of time scale.     

Liénard-type chemical oscillator

Using first-principles calculation, we have studied the properties of a series of M _x Co_1?x /Co(0001) (M = Pd, Pt) bimetallic surface alloys with atom M ratios from 0.25 to 1.0, then the effect of alloyed M metal on the properties of S adsorbed on these surfaces are discussed. Our calculations show that the alloying of metal Pd, Pt on Co(0001) weakens the S-M (M = Pd, Pt, Co) bond strength compared to monometallic surfaces and the site preference of sulfur atom is dependent on the alloyed metal M and its surface concentration. Moreover, bimetallic surface electronic structure modifications with and without sulfur are analyzed in comparison with clean Co(0001), and the correlation between the sulfur adsorption energy and the bimetallic surface d-band center is presented.     

Tribological Behavior of Multiply-Alkylated Cyclopentanes (MACs)-Cu Nanoparticles Composite Thin Film

Multiply-alkylated cyclopentanes (MACs) composite thin films containing Cu nanoparticles are fabricated on the octadecyltrichlorosilane (OTS)-modified substrate by a spin-coating technique. The thickness, wetting behavior, and nanoscale morphologies of the films are characterized by means of ellipsometry, contact angle measurement, and atomic force microscope (AFM). The friction and wear behaviors of the thin films sliding against Si₃N₄ ball are examined on a UMT-2MT tribometer in a ball-on-disk contact mode. The worn surfaces of the OTS-MAC-Cu composite film and the counterpart Si₃N₄ balls are investigated with a scanning electron microscope. Water contact angle on OTS-MAC-Cu composite film is higher than that of OTS-MAC film. OTS-MAC-Cu composite film exhibits higher load-carrying capacity and better friction reduction and antiwear behavior as compared with OTS-MAC film. This may be attributed to the load-carrying and self-repairing property of the Cu nanoparticles in the composite film and the formation of a transfer layer composed of OTS, MAC, and Cu on the rubbing surface of the counterpart ball.     

Improved multiferroic properties and a novel magnetic behavior of Bi0.8La0.2Fe1−xCoxO3 nanoparticles

Bi_0.8La_0.2Fe_1−xCo_xO₃ nanoparticles of single phase (BLFCO_x, x=0, 0.005, 0.01, 0.02) were prepared by a sol-gel method using polyvinyl alcohol as a surfactant. Co substitution at Fe site improved further dielectric properties of Bi_0.8La_0.2FeO₃ nanoparticles in the frequency range below 25 MHz at room temperature. Magnetization at 10 kOe, coercivities, and remanence of BLFCO_x nanoparticles increased with increasing Co content. It is interesting that the hysteresis loop of all the BLFCO_x nanoparticles presented a wasp-waisted shape. The property can open an important way to design new multiferroic applications of low hysteresis loss in low magnetic fields.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.