Behavior of oxygen in zinc oxide films through thermal annealing and its effect on sheet resistance

Behavior of oxygen in sputtering deposited ZnO films through thermal annealing and its effect on sheet resistance of the films were investigated. The crystallinities of the ZnO film were improved by post-deposition annealing in vacuum. However, the sheet resistance of ZnO film was dramatically decreased after post-deposition annealing in vacuum at more than 300 °C, while O₂ desorbed from the film. The oxygen vacancies which acted as donors were formed by the thermal annealing in vacuum. The sheet resistance of the films was recovered by annealing in oxygen ambient. In this paper, ¹⁸O₂ gas as an oxygen isotope was used as the annealing ambient in order to distinguish from ¹⁶O, which was constituent atom of the ZnO films. SIMS analysis revealed that ¹⁸O diffused into the ZnO film from the top surface by ¹⁸O₂ annealing. Therefore oxygen vacancies formed by the post-deposition annealing in vacuum could be compensated by the annealing in oxygen ambient.     

Fabrication and characterization of zinc oxide anti-reflective coating on flexible thin film microcrystalline silicon solar cell

This paper studies the fabrication and characterization of 80 nm zinc oxide anti-reflective coating (ARC) on flexible 1.3 μm thin film microcrystalline silicon (μc-Si) solar cell. High resolution X-ray diffraction (HR-XRD) shows a c-axis oriented ZnO (0 0 2) peak (hexagonal crystal structure) at 34.3° with full width at half maximum (FWHM) of 0.3936°. Atomic force microscope (AFM) measures high surface roughness root-mean-square (RMS) of the layer (50.76 nm) which suggests scattering of the incident light at the front surface of the solar cell. UV–vis spectrophotometer illustrates that ZnO ARC has optical transmittance of more than 80% in the visible and infra-red (IR) regions and corresponds to band gap (E_g) of 3.3 eV as derived from Tauc equation. Inclusion of ZnO ARC successfully suppresses surface reflectance from the cell to 2% (at 600 nm) due to refractive index grading between the Si and the ZnO besides quarter-wavelength (λ/4) destructive interference effect. The reduced reflectance and effective scattering effect of the incident light at the front side of the cell are believed to be the reasons why short-circuit current (I_sc) and efficiency (η) of the cell improve.     

Influence of high-energy X-ray irradiation on the optical properties of tetraphenylporphyrin thin films

Tetraphenylporphyrin (TPP) thermally evaporated films were irradiated by different doses (0.5–2.5 kGy) of X-ray with energy 6 MeV. The optical properties for TPP were investigated using spectrophotometric measurements of the transmittance and reflectance at normal incidence of light in the wavelength range from 200 to 1100 nm. The absorption spectra recorded in the UV-VIS region of spectra showed different absorption bands, namely four Q-bands in the visible region of the spectrum and a more intense band termed as the Soret band in the near-UV region of the spectrum. Two other bands labeled N and M appear in the UV region. The Soret band showed Davydov splitting. Increasing X-ray irradiation dose influences the optical properties of TPP films. All absorption bands show a continuous blue shift in position and a decrease in intensity with increasing X-ray dose. At 2.5 kGy the B, N, and M bands disappeared. The reduction in the absorbency was calculated as a function of X-ray dose. The energy gap was determined and the type of optical transition was found to be an indirect allowed transition.     

Investigation of chemical mechanical polishing of zinc oxide thin films

Zinc oxide has become an important material for various applications. Commercially available zinc oxide single crystals and as-grown zinc oxide thin films have high surface roughness which has detrimental effects on the growth of subsequent layers and device performance. A chemical mechanical polishing (CMP) process was developed for the polishing of zinc oxide polycrystalline thin films. Highly smooth surfaces with RMS roughness <6 Å (as compared to the initial roughness of 26 ± 6 Å) were obtained under optimized conditions with removal rates as high as 670 Å/min. Effects of various CMP parameters on removal rate and surface roughness were evaluated. The role of pH on the polishing characteristics was investigated in detail.     

Deposition of zinc oxide thin films by reactive pulsed laser ablation

Thin films of zinc oxide have been deposited by reactive pulsed laser ablation of Zn and ZnO targets in presence of a radio frequency (RF) generated oxygen plasma. The gaseous species have been deposited at several substrate temperatures, using the on-axis configuration, on Si (1 0 0). Thin films have been characterized by scanning electron microscopy, atomic force microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and infrared spectroscopy. A comparison among conventional PLD and reactive RF plasma-assisted PLD has been performed.     

Spray deposition of highly transparent fluorine doped cadmium oxide thin films

The cadmium oxide (CdO) and F:CdO films have been deposited by spray pyrolysis method using cadmium acetate and ammonium fluoride as precursors for Cd and F ions, respectively. The effect of temperature and F doping on the structural, morphological, optical and Hall effect properties of sprayed CdO thin films was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), optical absorption and electrical measurement techniques. TGA and DTA studies, indicates the formation of CdO by decomposition of cadmium acetate after 250 °C. XRD patterns reveal that samples are polycrystalline with cubic structure and exhibits (2 0 0) preferential orientation. Considerable broading of (2 0 0) peak, simultaneous shifting of corresponding Bragg's angle have been observed with respect to F doping level. SEM and AFM show the heterogeneous distribution of cubical grains all over the substrate, which are randomly distributed. F doping shifts the optical gap along with the increase in the transparency of CdO films. The Hall effect measurement indicates that the resistivity and mobility decrease up to 4% F doping.     

Effect of annealing on properties of electrochemically deposited CdTe thin films

Thin films of CdTe have been deposited onto stainless steel and fluorine-doped tin oxide (FTO)-coated glass substrates from aqueous acidic bath using electrodeposition technique. The different preparative parameters, such as deposition time, bath temperature and pH of the bath have been optimized by photoelectrochemical (PEC) technique to get good quality photosensitive material. The deposited films are annealed at different temperature in presence of air. Annealing temperature is also optimized by PEC technique. The film annealed at 200 °C showed maximum photosensitivity. Different techniques have been used to characterize as deposited and also as annealed (at 200 °C) CdTe thin film. The X-ray diffraction (XRD) analysis showed the polycrystalline nature, and a significant increase in the XRD peak intensities is observed for the CdTe films after annealing. Optical absorption shows the presence of direct transition with band gap energy 1.64 eV and after annealing it decreases to 1.50 eV. Energy dispersive analysis by X-ray (EDAX) study for the as-deposited and annealed films showed nearly stoichiometric compound formation. Scanning electron microscopy (SEM) reveals that spherically shaped grains are more uniformly distributed over the surface of the substrate for the CdTe film.     

Preparation and characterization of ZnO thin films prepared by thermal oxidation of evaporated Zn thin films

In this paper, the experimental results regarding some structural, electrical and optical properties of ZnO thin films prepared by thermal oxidation of metallic Zn thin films are presented.Zn thin films (d=200–400 nm) were deposited by thermal evaporation under vacuum, onto unheated glass substrates, using the quasi-closed volume technique. In order to obtain ZnO films, zinc-coated glass substrates were isochronally heated in air in the 300–660 K temperature range, for thermal oxidation.X-ray diffraction (XRD) studies revealed that the ZnO films obtained present a randomly oriented hexagonal nanocrystalline structure. Depending on the heating temperature of the Zn films, the optical transmittance of the ZnO films in the visible wavelength range varied from 85% to 95%. The optical band gap of the ZnO films was found to be about 3.2 eV. By in situ studying of the temperature dependence of the electrical conductivity during the oxidation process, the value of about 2×10⁻² Ω⁻¹ m⁻¹ was found for the conductivity of completely oxidized ZnO films.     

ZnO薄膜的激光辐照效应研究

研究了KrF准分子激光辐照对ZnO薄膜的本征缺陷.紫外（UV）发光以及表面形貌的影响,并对室温下ZnO的UV发射机理进行了详细探讨.结果表明激光辐照打断了薄膜内Zn—O键,氧空位（锌填隙）增多,导致表面电阻率下降,载流子浓度升高,调节激光辐照能量密度,可在较大范围内调控ZnO薄膜中的施主缺陷浓度;同时在激光热效应作用下,薄膜晶粒熔融长大,表面粗糙度大大降低;室温下ZnO薄膜的UV发光包括自由激子复合发光（FX）及其声子伴线（FX-LO）,缺陷浓度决定了FX与FX-LO的相对强度比,进而影响UV发射峰的强度以及位置.因此,激光辐照可以快速、有效地对ZnO薄膜内的缺陷浓度进行调控,从而控制其室温下的UV发射强度,这对于提高ZnO基光电器件的性能具有重要意义. 关键词： ZnO薄膜 激光辐照 紫外发光 缺陷浓度     

Properties of mixed molybdenum oxide-iridium oxide thin films synthesized by spray pyrolysis

Molybdenum-doped iridium oxide thin films have been deposited onto corning glass- and fluorine-doped tin oxide coated corning glass substrates at 350 °C by using a pneumatic spray pyrolysis technique. An aqueous solution of 0.01 M ammonium molybdate was mixed with 0.01 M iridium trichloride solution in different volume proportions and the resultant solution was used as a precursor solution for spraying. The as-deposited samples were annealed at 600 °C in air medium for 1 h. The structural, electrical and optical properties of as-deposited and annealed Mo-doped iridium oxide were studied and values of room temperature electrical resistivity, and thermoelectric power were estimated. The as-deposited samples with 2% Mo doping exhibit more pronounced electrochromism than other samples, including pristine Ir oxide.     

The influence of oxygen on the optical properties of RF-sputtered zinc oxide thin films

In this article, we investigate the effects of oxygen partial pressure in the deposition chamber on the optical properties of zinc oxide (ZnO) thin films; in particular, we examine the variation of the refractive index with oxygen flux.ZnO thin films were deposited by radio-frequency (RF) magnetron sputtering and studied by means of X-ray diffraction (XRD) and spectroscopic ellipsometry (SE). We have found a preferential c-axis growth of ZnO films, with slightly variable deposition rates from 2.6 to 3.8 Å/s. Conversely, the refractive index exhibits, from ultraviolet (UV) to near infrared (IR), a considerable and almost linear variation when the oxygen flux value in the deposition chamber varies from 0 to 10 sccm.     

The influence of doping element on structural and luminescent characteristics of ZnS thin films

For the fabrication of green and blue emitting ZnS structures the elements of I, III, and VII groups (Cu, Al, Ga, Cl) are used as dopants. The influence of type of impurity, doping technique, and type of substrate on crystalline structure and surface morphology together with luminescent properties was investigated. The doping of thin films was realized during the growth process and/or post-deposition thermal treatment. ZnS thin films were deposited by physical (EBE) and chemical (MOCVD) methods onto glass or ceramic (BaTiO₃) substrates. Closed spaced evaporation and thermodiffusion methods were used for the post-deposition doping of ZnS films. X-ray diffraction (XRD) techniques, atomic force microscopy (AFM), and measurements of photoluminescent (PL) spectra were used for the investigations. It was shown that the doping by the elements of I (Cu) and III (Al, Ga) groups does not change the crystal structure during the thermal treatment up to 1000 C, whereas simultaneous use of the elements of I (Cu) and VII (Cl) groups leads to decrease of the phase transition temperature to 800 C. The presence of impurities in the growth process leads to a grain size increase. At post-deposition treatment Ga and Cl act as activators of recrystallization process. The transition of ZnS sphalerite lattice to wurtzite one leads to the displacement of the blue emission band position towards the short-wavelength range by 10 nm.     

Effect of freon flow rate on tin oxide thin films deposited by chemical vapor deposition

High quality fluorine-doped tin oxide (SnO₂:F) films on glass substrates were been prepared using chemical vapor deposition (CVD) method. The electrical properties, surface morphologies, structural properties and optical properties of the films were studied by varying the freon flow rates. The structure was analyzed by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the morphology. Energy-dispersive spectroscopy (EDS) was conducted to understand the surface fluorine composition of the film. The results showed that crystalline structure of the film had a have cassiterite-like diffraction patterns with a preferred orientation of (1 1 0). Surface roughness was evaluated by atomic force microscopy, characterized by root mean square (RMS) and average value (Ra). The SnO₂:F resistivity decreased as the freon flow rate increased. The films had a uniform thickness and a transmittance of 80–90% within the visible region of the spectrum.     

Second harmonic generation of fluorine-doped zinc oxide thin films grown on soda-lime glass substrates by a chemical spray technique

Second harmonic generation (SHG) studies of fluorine-doped zinc oxide (ZnO:F) thin films deposited on soda-lime glass substrates from an aged solution in conjunction with zinc pentanedionate, using the chemical spray deposition technique were carried out. The and independent tensorial components of the quadratic nonlinear optical susceptibility of the ZnO:F thin films were evaluated. Scanning electron microscopy and X-ray diffraction investigations revealed a homogeneous distribution of nanoparticles of similar size and morphology for various samples deposited at different substrate temperatures (ranging from 400 to 525 °C). The SHG-technique revealed a clear dependence of the nonlinear optical response with the deposition temperature. Typical optical transmittance and photoluminescence (PL) studies were also performed, from which a bandgap (E_g) of 3.3 eV was evaluated in films deposited under optimal conditions of conductivity and transmittance.     

Low operating temperature of oxygen gas sensor based on undoped and Cr-doped ZnO films

Undoped and doped ZnO with 1 at.% (atomic percentage) chromium (Cr) was synthesized by RF reactive co-sputtering for oxygen gas sensing applications. The prepared films showed a highly c-oriented phase with a dominant (0 0 2) peak at a Bragg angle of around 34.2°. The operating temperature of the prepared ZnO sensor was around 350 °C and shifted to around 250 °C for the doped ZnO sensor which is lower than that of previously reported work. The sensitivity of the sensor toward oxygen gas was enhanced by doping ZnO with 1 at.% Cr. Good stability and repeatability of the sensor were demonstrated when tested under different concentration of oxygen atmosphere.     

Effects of electron-beam irradiation on structural,electrical, and optical properties of amorphous indium gallium zinc oxide thin films

High-energy electron-beam irradiation of indium gallium zinc oxide (IGZO) films improved the short-range arrangement. The increase in band gap was used as an indication of such improvement. X-ray diffraction confirmed that the films treated with a DC voltage of 2–4.5 kV for duration of up to 35 min are in the amorphous state or nanocrystalline phase. Higher energy electron-beam irradiation led to increased conductivity, which mainly comes from the drastic increase in electron concentration. Electron-beam treatment could be a viable route to improve the contact resistance between the source/drain and channel layer in thin-film transistor devices.     

Evaluation of acoustoelectric UV sensor according to ZnO thin film properties

This paper presents an improvement of the acoustoelectric effect by sensitivity and response of ultraviolet (UV) sensors by changing the argon/oxygen ratio. The acoustoelectric sensor is a delay-line type with a center frequency of 240.2625 MHz and fabricated on a piezoelectric substrate. Aluminum thin films were deposited as interdigitated transducers and patterned, and the ZnO thin film was deposited as a UV sensing layer by controlling the ratio of argon and oxygen with an RF magnetron sputtering. By increasing the oxygen partial pressure during ZnO deposition, the photoconductivity increased by 6.5 times, thereby increasing the frequency change related to the sensitivity of the sensor. The sensitivity to UV light was 110.4 Hz cm²/μW under an argon/oxygen ratio of 6:4, which is an increase of 5.1 times from 21.76 Hz cm²/μW obtained under a ratio of 10:2. In addition, the response and recovery times were improved by 2.85 times and 3.02 times, respectively.     

60keV质子辐照对TiNi记忆合金薄膜马氏体相变的影响

 利用磁控溅射的方法在氧化后的单晶Si基片上制备了TiNi形状记忆合金薄膜，利用示差扫描量热法和原位X射线衍射研究了薄膜的马氏体相变特征。通过60keV质子注入（辐照）薄膜样品研究了H+离子对合金薄膜马氏体相变特征的影响，结果表明氢离子注入后引起了马氏体相变开始Ms和结束点Mf以及逆马氏体相变开始As和结束温度Af的下降，而对R相变开始Rs和结束温度Rf影响不大。掠入射X射线衍射表明H+离子注入后有氢化物形成。H⁺离子注入形成的氢化物是引起相变点的变化的主要因素。     

Lactic acid aided electrochemical deposition of c-axis preferred orientation of zinc oxide thin films: Structural and morphological features

Compact and homogeneous c-axis preferred orientation of zinc oxide (ZnO) films on indium tin oxide (ITO) coated glass have been prepared electrochemically at −1.2 V vs. Ag|AgCl in a weak acidic condition from 0.06 M Zn(NO₃)₂ with 3 mM lactic acid (LA) added. LA was found having strong influence on the electrodeposition of c-axis preferred orientation of zinc oxide films. Other experimental variables such as deposition temperature, potential, and precursor concentration were also conducted in this article. Among these variables, it was found that precursor concentration of zinc nitrate influenced significantly on growth direction and crystal diameter of zinc oxide. Cyclic voltammetry was used to observe the electrochemistry of the deposition. Crystallinities of the films were examined by X-ray diffractometer. The morphologies of zinc oxide films were observed with a field emitting scanning electron microscope. Optical characteristics of zinc oxide layers were measured with UV-vis spectrophotometer. The band gap of the deposited zinc oxide thin films was evaluated from the Tauc relationship of (αhν)² vs. hν, which was found to be 3.31 eV.     

Enhanced field emission characteristics of zinc oxide mixed carbon nano-tubes films

A composite material of Zinc oxide and carbon nano-tubes (ZnO-CNTs) paste was synthesized by mixing multi-wall CNTs, ZnO nano-grains and organic vehicles. The microstructures and the morphologies of screen-printed films were characterized by field-emission scanning electron microscope. Results show that ZnO flakes geometrically matched with CNTs by filling into the interspaces of CNTs or directly covering upon CNTs. The field emission characteristics of films are found to be greatly effected by ZnO nano-grains. Especially, the turn-on electric field of ZnO-CNT film (1.17 V/μm) which is far lower than that of usual CNT films (1.70 V/μm). Furthermore, except that better emission stability is achieved, brightness and emission uniformity are notably enhanced as well. It can be speculated that the special microstructures of ZnO mixed CNT films dominate the enhanced electrical conductivity, thermal conductivity, and effective emitters.