Dynamic wettability of wood surface modified by acidic dyestuff and fixing agent

Acidic dyestuffs can bring brilliant colors to the wood and fixing agents can avoid the color loss. They could change the surface wettability of wood, which impact the gluing process of veneers. In condition of the higher moisture content of wood, the rare veneers, the veneers dyed by acidic dyestuffs and the dyed veneers fixed by Chitosan were glued respectively by one-component wet-curing isocyanate adhesive and the contact angles (θ) of the different gluing interfaces were measured. The dynamic wettability of these gluing interfaces was characterized by both the contact angle θ and the spreading-penetration parameter (K) calculated by θ. The results showed that the θ-values decreased significantly with the extension of time and the initial contact angles (θ_i) decreased with the moisture contents of veneers increasing, but the variation of the balance contact angles (θ_e) was reversed with θ_i. When the moisture contents of veneers were same, the variation of θ of the rare veneers was minimal and the variation of θ of the fixed veneers was maximal. The K-values of these gluing interfaces all decreased significantly with the moisture contents of veneers increasing, but the variations of K were different. The wetting model describing the dynamic wetting process was established on the basis of these variations.     

Effects of surface inactivation, high temperature drying and preservative treatment on surface roughness and colour of alder and beech wood

Although extensive research has been conducted in wood surface quality analysis, a unified approach to surface quality characterisation does not exist. Measurements of the variation in surface roughness and surface colour are used widely for the evaluation of wood surface quality. Colour is a basic visual feature for wood and wood-based products. Colour measurement is one of the quality control tests that should be carried out because the colour deviations are spotted easily by the consumers. On the other hand, a common problem faced by plywood manufacturers is panel delamination, for which a major cause is poor quality glue-bonds resulting from rough veneer. Rotary cut veneers with dimensions of 500 mm × 500 mm × 2 mm manufactured from alder (Alnus glutinosa subsp. barbata) and beech (Fagus orientalis Lipsky) logs were used as materials in this study. Veneer sheets were oven-dried in a veneer dryer at 110 °C (normal drying temperature) and 180 °C (high drying temperature) after peeling process. The surfaces of some veneers were then exposed at indoor laboratory conditions to obtain inactive wood surfaces for glue bonds, and some veneers were treated with borax, boric acid and ammonium acetate solutions. After these treatments, surface roughness and colour measurements were made on veneer surfaces. High temperature drying process caused a darkening on the surfaces of alder and beech veneers. Total colour change value (ΔE^*) increased linear with increasing exposure time. Among the treatment solutions, ammonium acetate caused the biggest colour change while treatment with borax caused the lowest changes in ΔE^* values. Considerable changes in surface roughness after preservative treatment did not occur on veneer surfaces. Generally, no clear changes were obtained or the values mean roughness profile (R_a) decreased slightly in R_a values after the natural inactivation process.     

On the impact of non-sphericity and small-scale surface roughness on the optical properties of hematite aerosols

We perform a comparative modelling study to investigate how different morphological features influence the optical properties of hematite aerosols. We consider high-order Chebyshev particles as a proxy for aerosol with a small-scale surface roughness, and spheroids as a model for nonspherical aerosols with a smooth boundary surface. The modelling results are compared to those obtained for homogeneous spherical particles. It is found that for hematite particles with an absorption efficiency of order unity the difference in optical properties between spheres and spheroids disappears. For optically softer particles, such as ice particles at far-infrared wavelengths, this effect can be observed for absorption efficiencies lower than unity. The convergence of the optical properties of spheres and spheroids is caused by absorption and quenching of internal resonances inside the particles, which depend both on the imaginary part of the refractive index and on the size parameter, and to some extent on the real part of the refractive index. By contrast, small-scale surface roughness becomes the dominant morphological feature for large particles. This effect is likely to depend on the amplitude of the surface roughness, the relative significance of internal resonances, and possibly on the real part of the refractive index. The extinction cross section is rather insensitive to surface roughness, while the single-scattering albedo, asymmetry parameter, and the Mueller matrix are strongly influenced. Small-scale surface roughness reduces the backscattering cross section by up to a factor of 2-3 as compared to size-equivalent particles with a smooth boundary surface. This can have important implications for the interpretation of lidar backscattering observations.     

Effects of textural and surface characteristics of microporous activated carbons on the methane adsorption capacity at high pressures

The objective of this study is to relate textural and surface characteristics of selected microporous activated carbons to their methane storage capacity. In this work, a magnetic suspension balance (Rubotherm, Germany) was used to measure methane adsorption isotherms of several activated carbon samples. Textural characteristics were assessed by nitrogen adsorption on a regular surface area analyzer (Autosorb-MP, by Quantachrome, USA). N₂ adsorption was analysed by conventional models (BET, DR, HK) and by Monte Carlo molecular simulations. Elemental and surface analyses were performed by X-ray photoelectronic spectroscopy (XPS) for the selected samples. A comparative analysis was then carried out with the purpose of defining some correlation among the variables under study. For the system under study, pore size distribution and micropore volume seem to be a determining factor as long as the solid surface is perfectly hydrophobic. It was concluded that the textural parameters per se do not unequivocally determine natural gas storage capacities. Surface chemistry and methane adsorption equilibria must be taken into account in the decision-making process of choosing an adsorbent for gas storage.     

A morphological study of vicinal surface growth based on a hybrid algorithm

A hybrid algorithm that combines a phase-field model and a lattice gas model evolving according to a kinetic Monte-Carlo (KMC) simulation scheme is used to investigate the dynamics of vicinal surface growth during vapor phase epitaxy. The algorithm is computationally far more efficient than pure KMC schemes, and this gain in efficiency does not correspond to a loss in information on the kinetics of individual atoms. We present numerical studies on the temperature dependence of macroscopic properties of the growing surface, evaluating the relevant stochastic processes (attachment, detachment, diffusion and island dynamics) as a function of their rates. We show that the temperature at which step flow is replaced by island nucleation depends on incoming flux, diffusion parameters and interstep distance. Moreover, we validate these finding by comparison to experiments and by analytical investigations.     

Adsorption site preference of CO2 on the Pt(1 0 0) surface by ab initio calculations

This paper investigates the adsorption sites and electronic structure of the adsorption of CO₂ on the Pt(1 0 0) surface by ab initio periodic density functional theory (DFT) methods. Several parallel and vertical adsorption sites are examined in detail. The results show that the adsorption energy for the atop hollow horizontal (thh) site is 0.34 eV. However, other sites only have small binding energies and these values are very close. For an atop hollow horizontal site, the calculated elecronic interaction is contributed to not only the Pt-O atoms, but also Pt-C atoms. So the results indicate that the thh site is the most favorable and stable.     

The study on the surface state of CdZnTe (1 1 0) surface

Angle-resolved photoemission spectroscopy (ARPES) was used to characterize the surface state of clean CdZnTe (1 1 0) surface. The surface state of CdZnTe with the peak at 0.9 eV below the Fermi level is identified. Meanwhile, Photoluminescence (PL) spectrum confirmed that there existed a surface trap state which introduced a deep-level peak at 1.510 eV. The surface trap states can be decreased by aging in dry-air. The surface leakage current was measured also by I-V measurements. After aging, the leakage current was decreased remarkably, which suggested that the aging treatment is an effective method to decrease the surface trap state.     

Ab-initio pseudopotential study of electronic structure and chemisorption of oxygen on aluminium surface

Chemisorption of oxygen atom on aluminium (1 1 1), (1 1 0) and (1 0 0) surfaces is studied using ab-initio plane wave pseudopotential method based on density functional theory (DFT). Oxygen atom chemisorbed on three different high symmetry sites; top, short-bridge and hollow sites on the aluminium surfaces are examined. It has been found that the O-adatom adsorbed at the hollow site on aluminium (1 1 1), (1 1 0) and (1 0 0) plane yield energetically most stable structure. Calculation of chemisorption energies of O-adatom on aluminium surfaces shows that oxygen is most strongly bound to aluminium atoms on Al(1 1 1) plane and the calculated value of the chemisorption energy of O-adatom at the hollow site on Al(1 1 1) surface is 4.8 eV. In this work, the chemisorption energies calculated for O-adatom on Al(1 1 0) and Al(1 0 0) surfaces are reported for the first time. The electronic structures and the electronic charge density distributions of the oxygen chemisorbed aluminium surfaces are also investigated. Calculations show that for aluminium, p orbitals also contribute significantly along with the s orbitals during the bond formation with oxygen atom. Therefore, the possibilities of hybridizations lead to the strong bonding configurations.     

Synthesis surface effects on the stress and deformation of film/substrate system

The closed-form solutions of bending curvature and stress distribution in film/substrate system with the synthesis surface effect are proposed by minimizing the total potential energy. Effects of the roughness and the residual surface stress on stress in film are addressed. Results reveal that, at a given thickness of the substrate, effects of roughness and residual surface stress on the bending curvature become significant with decreasing the film thickness. The roughing surface will enlarge the magnitudes of bending curvature and film stress. The direction change of residual surface stresses can lead to a reversed bending of film/substrate system.     

Influence of the substrate position angle on the adhesion of ZnO thin films deposited on polyimide foil substrates

ZnO thin films, as polymer protection layers against ultraviolet radiation, were deposited on polyimide foil substrates using cathodic vacuum arc deposition technique. X-ray diffraction results showed that all the samples had (0 0 2) preferred orientation and the FWHM decreased as the position angle decreased. A fragmentation test was employed to investigate the influence of substrate position angle on the adhesion of ZnO thin films. It was found that the intrinsic adhesion between the ZnO film and the polyimide substrate is about 60 MPa at the substrate position angle of 0°. When the position angle increases to ±60°, the value of intrinsic adhesion decreases to about 30 MPa.     

Protein adsorption resistant surface on polymer composite based on 2D- and 3D-controlled grafting of phospholipid moieties

To prepare the biocompatible surface, a phosphorylcholine (PC) group was introduced on this hydroxyl group generated by surface hydrolysis on the polymer composite composed of polyethylene (PE) and poly (vinyl acetate) (PVAc) prepared by supercritical carbon dioxide. Two different procedures such as two-dimensional (2D) modification and three-dimensional (3D) modification were applied to obtain the steady biocompatible surface. 2D modification was that PC groups were directly anchored on the surface of the polymer composite. 3D modification was that phospholipid polymer was grafted from the surface of the polymer composite by surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-methacryloyloxyethyl phosphorylcholine (MPC). The surfaces were characterized by X-ray photoelectron spectroscopy, dynamic water contact angle measurements, and atomic force microscope. The effects of the poly(MPC) chain length on the protein adsorption resistivity were investigated. The protein adsorption on the polymer composite surface with PC groups modified by 2D or 3D modification was significantly reduced as compared with that on the unmodified PE. Further, the amount of protein adsorbed on the 3D modified surface that is poly(MPC)-grafted surface decreased with an increase in the chain length of the poly(MPC). The surface with an arbitrary structure and the characteristic can be constructed by using 2D and 3D modification. We conclude that the polymer composites of PE/PVAc with PC groups on the surface are useful for fabricating biomedical devices due to their good mechanical and surface properties.     

Analysis of the impact of agglomeration and surface chemistry models on soot formation and oxidation

Models for soot aggregation that account for the influence of soot surface chemistry on mass growth and oxidation are still at the formative stage. Past studies have considered techniques ranging from the method of moments to stochastic approaches and significantly different sensitivities to chemical processes such as mass growth and oxidation have been reported. The method of moments is computationally efficient and can yield encouraging results for laminar flames as well as for turbulent flames when combined with transported probability density function (PDF) methods. However, an assessment of the sensitivity to constituent model assumptions is not trivial and information regarding the soot size distribution is incomplete. In the current work, the ability of a sectional method to reproduce population dynamics data has been evaluated along with the sensitivity of predictions to closure elements associated with soot nucleation, agglomeration, surface growth and oxidation. A detailed chemistry model with 285 chemical species and 1520 reactions was used for the gas phase. It is shown that the approach to the fuel lean sooting limit can be reproduced with reasonable accuracy and that the inclusion of fractal aggregates and surface chemistry effects improve agreement with experimental data.     

Influence of growth and anneal conditions on the surface roughness of L10 Fe50PdxPt50−x thin films

We deposit Fe₅₀Pd_xPt_50−x alloy thin films by magnetron sputtering onto a TiN seed layer. Chemically ordered L1₀ films are obtained which display large perpendicular magnetic anisotropy. We find that the surface roughness of the film depends strongly on the growth and anneal conditions as well as the Pd composition of the film. Smooth films are obtained by deposition above the chemical ordering temperature and by removing Pd from the alloy.     

Influence of the redox state of QA on phycobilisome mobility in the cyanobacterium Synechocystis sp. strain PCC 6803

In a unicellular cyanobacterium, the mobile fraction of phycobilisome (PBS) was found to be maximum at a particular redox value of Q_A (i.e., 0.52). An upward or downward shift in the redox value leads to a decrease in this mobile fraction of PBS. Furthermore, the regulatory effect of the redox state of Q_A on PBS mobility was found to be independent of the effect exerted by the plastoquinone pool. These findings indicate for the first time that PBS mobility is regulated by the Q_A redox state in cyanobacteria. A possible working mechanism underlying this control is discussed.     

Influence of the surface conditions on rf plasma characteristics

The secondary electron emission is a surface dependent phenomenon, more influenced by surface preparation than by the material itself. The present paper deals with the effect of the electrode surface conditions: clean (atomically clean) and contaminated electrodes (standard conditions even after mechanical and chemicals cleaning) on the characteristics of an asymmetric discharge by PIC/MCC simulations. In the arrangement with one clean and one contaminated electrode the discharge characteristics strongly depend upon which electrode is powered. The obtained PIC/MCC simulation results indicate that contamination of electrodes and variations of the secondary electron emission coefficients can lead to more or less significant changes in properties of rf plasmas.     

The different self-assembled way of n- and t-dodecyl mercaptan on the surface of copper

The self-assembled monolayers (SAMs) of n- and t-dodecyl mercaptan on the surface of copper have been obtained. As evidenced by electrochemical impedance spectroscopy (EIS), two kinds of the alkanethiols can self-assemble on the copper surface. But the results of the quartz crystal microbalance (QCM) show that the self-assembled way of the two alkanethiols are different. The SAMs of n-dodecyl mercaptan can increase the weight of the QCM electrode and the SAMs of t-dodecyl mercaptan, on the contrary, make the weight of the QCM electrode decrease. Inspected with the SEM, it is found that a lot of pits spread all over the copper surface after having been modified with t-dodecyl mercaptan. All the results suggest that the self-assemble of t-dodecyl mercaptan on the copper surface can erode and dissolve copper surface sharply.     

BOF endpoint prediction based on the flame radiation by hybrid SVC and SVR modeling

A new non-contact method for predicting the endpoint carbon content of different kinds of basic oxygen furnace (BOF) vessel sizes is presented in this paper. The proposed model is based on the spectral distribution of the flame at the vessel mouth with support vector machine (SVM). Two models are constructed with SVM in this paper: a SVC model is used to classify the whole blowing phases based on the mechanism analysis, and an ?-SVR model is constructed to map the flame spectrum variation into the state of the molten steel in the iron bath. The simulation results on industrial datasets show that the proposed method can offer an accurate as well as convenient way to improve the performance of BOF endpoint control compared with current methods of endpoint carbon content prediction.     

Effects of swift heavy ion irradiation on the electrical characteristics of Au/n-GaAs Schottky diodes

Metal-semiconductor diode of Au/n-GaAs is studied under the irradiation of swift heavy ion (SHI) beam (80 MeV ¹⁶O⁶⁺), using in situ current-voltage characterization technique. The diode parameters like ideality factor, barrier height, and leakage current are observed to vary with irradiation fluence. Significantly, the diode performance improves at a high fluence of 2 × 10¹³ ions cm⁻² with a large decrease of reverse leakage current in comparison to the original as deposited sample. The Schottky barrier height (SBH) also increases with fluence. At a high irradiation fluence of 5 × 10¹³ ions cm⁻² the SBH (0.62 ± 0.01 eV) is much larger than that of the as deposited sample (0.55 ± 0.01 eV). The diode parameters remain stable over a large range of irradiation up to fluence of 8 × 10¹³ ions cm⁻². A prominent annealing effect of the swift ion beam owing to moderate electronic excitation and high ratio of electronic energy loss to the nuclear loss is found to be responsible for the improvement in diode characteristics.     

The dc magnetic field,temperature and film thickness dependence of microwave surface resistance of YBCO and DyBCO thin films

We investigated the dc magnetic field and temperature dependences of the microwave surface resistance (R_s) of YBa₂Cu₃O_y (YBCO) and DyBa₂Cu₃O_y (DyBCO) superconducting thin films. The YBCO and DyBCO thin films, each with a thickness of 300, 500, or 700 nm, were deposited on MgO (1 0 0) substrates by the thermal co-evaporation method. The R_s was measured using the dielectric resonator method. A dc magnetic field of up to 5.0 T was applied parallel to the c-axis of the superconducting thin films. The results showed that the R_s value had almost the same temperature dependence at various thicknesses in a zero-external field. The R_s of the YBCO and DyBCO thin films increased with the applied dc magnetic field. The DyBCO thin films showed weaker magnetic field dependence of R_s than the YBCO thin films. The R_s ratio (defined as R_s(5 T)/R_s(0 T)) linearly increased with the film thickness. These results show that pinning strength decreased with an increasing film thickness.