Gas-sensing properties of perovskite La0.875Ba0.125FeO3 nanocrystalline powders

La_0.875Ba_0.125FeO₃ nanocrystalline powders have been prepared by a sol-gel method. The structure, conductance and gas-sensing properties were investigated. La_0.875Ba_0.125FeO₃ crystallizes as a perovskite phase with the orthorhombic structure. The La_0.875Ba_0.125FeO₃ based sensor shows good sensitivity and selectivity to alcohol gas. The highest sensitivity to 500 ppm alcohol gas reached was 58 at 170 °C. The adsorption of O₂ on the La_0.875Ba_0.125FeO₃ (0 1 0) surface was studied with the first-principles calculation based on the density functional theory. The results show that the surface states are near the Fermi energy level and that the Fe ion plays an important role in the process of oxygen adsorption, which affects the gas-sensing properties.     

Adsorption of CO, CO2 and NO molecules on a BaTiO3 (0 0 1) surface

Since the development of Scanning Tunnelling Microscopy (STM) technique, considerable attention has been devoted to various molecules adsorbed on various surfaces. Also, a new concept emerged with molecules on surfaces considered as nano machines by themselves. In this context, a thorough knowledge of surfaces and adsorbed molecules at an atomic scale are thus particularly invaluable. The present work describes the first Density Functional Theory (DFT) study of adsorption of CO, CO₂ and NO molecules on a BaTiO₃ surface following a first preliminary calculation of O and O₂ adsorption on the same surface. In the previously considered work, we found that a (0 0 1) surface with BaO termination is more stable than the one with TiO₂-termination. Consequently, we extended our study to CO, CO₂ and NO molecules adsorbed on a (0 0 1) surface with BaO termination. The present calculation was performed on a (1 × 1) cell with one monolayer of adsorbed molecules. Especially, a series of cases implying CO molecules adsorbed in various geometrical configurations has been examined. The corresponding adsorption energy varies in the range of −0.17 to −0.10 eV. The adsorption energy of a CO₂ molecule directly located above an O surface atom (called O_s) is of the order of −0.18 eV. The O-C distance length is then 1.24 Å and the O-C-O and O-C-O_s angles are 134.0° and 113.0°, respectively. For NO adsorption, the most important induced structural changes are the followings: (i) the N-O bond is broken when a NO molecule is absorbed on a Ba-O_s bridge site. In that case, N and O atoms are located above an O and a Ba surface atom, respectively, whereas the O-Ba-O_s and N-O_s-Ba angles are 106.5° and 63.0°, respectively. The N-O distance is as large as 2.58 Å and the adsorption energy is as much as −2.28 eV. (ii) In the second stable position, the NO molecule has its N atom adsorbed above an O_s atom, the N-O axis being tilted toward the Ba atom. The N-O_s-Ba angle is then 41.1° while the adsorption energy is only −0.10 eV. At last, the local densities of states around C, O as well as N atoms of the considered adsorbed molecules have also been discussed.     

Adsorption of formaldehyde on the Fe site of clean and M (Ca, Sr and Ba) doped LaFeO3 (0 1 0) surface

The adsorption of formaldehyde (H₂CO) on the Fe site of clean and M²⁺ (Ca²⁺, Sr²⁺ and Ba²⁺) doped LaFeO₃ (0 1 0) surface have been investigated using the density functional theory (DFT) method. Calculation results show that the oxygen atom of the H₂CO molecule prefers to be adsorbed on the Fe site of the clean LaFeO₃ (0 1 0) surface. The adsorption of H₂CO could change the electronic properties of the LaFeO₃, indicating that the LaFeO₃ could be used as gas sensing material to detect the H₂CO gas. The analysis results of the DOS suggest that the bonding mechanism between the H₂CO molecule and the Fe site is mainly from the interaction between the Fe 3d and H₂CO 2p orbital. Comparing with the binding energy and the net charge-transfer, we find that the M²⁺ (Ca²⁺, Sr²⁺ and Ba²⁺) doping cannot improve the sensitivity of the LaFeO₃ to the H₂CO gas.     

DFT study of NH3 dissociation on Si(1 1 1)-7 × 7. The role of intermolecular interactions

The adsorption of NH₃ molecule on the Si(1 1 1)-7 × 7 surface modelled with a cluster has been studied using density functional theory (DFT). The results indicate the existence of a precursor state for the non-dissociative chemisorption. The active site for the molecular chemisorption is the adatom; while the NH₃ molecule adsorbs on the Si restatom via this preadsorbed state, the adsorption on the Si adatom is produced practically without an energy barrier. The ammonia adsorption on the adatom induces an electron transfer from the dangling bond of this atom to the dangling bond of the adjacent Si restatom, hindering this site for the adsorption of a second NH₃ incoming molecule. However, this second molecule links strongly by means of two H-bonds. The dissociative chemisorption process was studied considering one and two ammonia molecules. For the dissociation of a lonely NH₃ molecule an energy barrier of ∼0.3 eV was calculated, yielding NH₂ on the adatom and H on the restatom. When two molecules are adsorbed, the NH₃-NH₃ interaction yields the weakening of a N-H bond of the ammonia molecule adsorbed closer the Si surface. As a consequence, the dissociation barrier practically disappears. Thus, the presence of a second NH₃ molecule at the adatom-restatom pair of the Si(1 1 1)-7 × 7 surface makes the dissociative reaction self-assisted, the total adsorption process elapsing with a negligible activation barrier (less than 0.01 eV).     

First-principles study on the catalytic role of Ag in the oxygen adsorption of LaMnO3(0 0 1) surface

In the present paper, the catalytic role of Ag in the oxygen adsorption of LaMnO₃(0 0 1) surface has been theoretically investigated using first-principles calculations based on the density functional theory (DFT) and pseudopotential method. The O₂ adsorption energy is larger for the vertical adsorption and the covalent bond was formed between O₂ molecule and surface Mn. The calculation of electronic properties of interaction between Ag atom and LaMnO₃(0 0 1) surface demonstrates that the most stable position for Ag adsorption is hollow site. The O₂ adsorption energy dramatically increased from 0.298 eV to 1.108 eV due to Ag pre-adsorbed. It is Ag pre-adsorbed that facilitates O₂ adsorption on surface. The bond length and bond population of O₂ molecule indicate that Ag atom facilitates O₂ molecule dissociative adsorption. The Ag atom strengthens LaMnO₃(0 0 1) substrate activity and activity center was formed on surface, which enhances the electrocatalytic activity of LaMnO₃ as solid oxide fuel cells cathode material at low temperature.     

Synthesis and electrical conductivity of various melilite-type electrolytes Ln1 + xSr1 − xGa3O7 + x/2

Melilite type ceramics ABC₃O₇ such as La_1.54Sr_0.46Ga₃O_7.27 are a new class of oxide conductors where the conductivity is carried out through interstitial oxygen ions. This work presents the attempt to replace the A-site element La with the other lanthanide elements and Y, resulting in various Ln_1 + xSr_1 − xGa₃O_7 + x/2 ceramics, in which Ln = La, Pr, Nd, Sm, Eu, Gd, Dy, Yb, Y, and 0.1 < x < 0.54. X-ray diffraction analysis shows that the melilite structure could be formed when the replacement is conducted with most lanthanides but not Yb and Y. Impedance spectroscopy demonstrates that the conductivity decreases dramatically with the decreasing of Ln³⁺ size and the charge-carrier concentration. These results suggest that, as an interstitial oxide ion electrolyte, La_1.54Sr_0.46Ga₃O_7.27 is the most promising ceramic in the Ln_1 + xSr_1 − xGa₃O_7+x/2 melilite family since La³⁺ has the largest ionic radius of the lanthanide elements.     

A theoretical investigation on Pt3Sn(1 0 2) surface alloy and CO-Pt3Sn(1 0 2) system

The adsorption properties of CO on experimentally verified stepped Pt₃Sn(1 0 2) surface were investigated using quantum mechanical calculations. The two possible terminations of Pt₃Sn(1 0 2) were generated and on these terminations all types of possible adsorption sites were determined. The adsorption energies and geometries of the CO molecule for all those sites were calculated. The most favorable sites for adsorption were determined as the short bridge site on the terrace of pure-Pt row of the mixed-atom-ending termination, atop site at the step-edge of the pure row of pure-Pt-ending termination and atop site at the step-edge of the pure-Pt row of the mixed-atom-ending termination. The results were compared with those for similar sites on the flat Pt₃Sn(1 1 0) surface considering the fact that Pt₃Sn(1 0 2) has terraces with (1 1 0) orientation. The LDOS analysis of bare sites clearly shows that there are significant differences between the electronic properties of Pt atoms at stepped Pt₃Sn(1 0 2) surface and the electronic properties of Pt atoms at flat (1 1 0) surface, which leads to changes in the CO bonding energies of these Pt atoms. Adsorption on Pt₃Sn(1 0 2) surface is in general stronger compared to that on Pt₃Sn(1 1 0) surface. The difference in adsorption strength of similar sites on these two surface terminations is a result of stepped structure of Pt₃Sn(1 0 2). The local density of states (LDOS) of the adsorbent Pt and C of adsorbed CO was utilized. The LDOS of the surface metal atoms with CO-adsorbed atop and of their bare state were compared to see the effect of CO chemisorption on the electron density distribution of the corresponding Pt atom. The downward shift in energy peak in the LDOS curves as well as changes in the electron densities of the corresponding energy levels indicate the orbital mixing between CO molecular orbitals and metal d-states. The present study showed that the adsorption strength of the sites has a direct relation with their LDOS profiles.     

Reaction mechanism for CO oxidation on Cu(3 1 1): A density functional theory study

The microscopic reaction mechanism for CO oxidation on Cu(3 1 1) surface has been investigated by means of comprehensive density functional theory (DFT) calculations. The elementary steps studied include O₂ adsorption and dissociation, dissociated O atom adsorption and diffusion, as well as CO adsorption and oxidation on the metal. Our results reveal that O₂ is considerably reactive on the Cu(3 1 1) surface and will spontaneously dissociate at several adsorption states, which process are highly dependent on the orientation and site of the adsorbed oxygen molecule. The dissociated O atom may likely diffuse via inner terrace sites or from a terrace site to a step site due to the low barriers. Furthermore, we find that the energetically most favorable site for CO molecule on Cu(3 1 1) is the step edge site. According to our calculations, the reaction barrier of CO + O → CO₂ is about 0.3 eV lower in energy than that of CO + O₂ → CO₂ + O, suggesting the former mechanism play a main role in CO oxidation on the Cu(3 1 1) surface.     

Methanol decomposition on the β-Ga2O3 (1 0 0) surface: A DFT approach

Density functional theory (DFT) cluster model calculations on methanol reactions on the β-Ga₂O₃ (1 0 0) surface have been realized. β-Ga₂O₃ structure has tetrahedral and octahedral ions and the results of gallia-methanol interaction are different depending on the local surface chemical composition. The surface without oxygen vacancies is very reactive and produces the methanol molecule decomposition. The unsaturated surface oxygen atoms strongly oxidize the methanol molecule. CO₂ and H₂O molecules are produced when methanol reacts with a free oxygen vacancy surface on octahedral gallium sites. On the other hand, H₂CO is found after the reaction of this molecule with a free O vacancy surface on tetrahedral gallium sites. A weak interaction between the remaining CO₂ molecule and the oxide surface was found, being this molecule easy to desorb. Otherwise, H₂CO has a stronger surface bond and it could suffer a later oxidation.     

First-principle study of NO adsorption on the LaFeO3 (0 1 0) surface

The adsorption of NO molecule on the LaFeO₃ (0 1 0) surface was studied using first-principle calculations based on density functional theory. The calculated results indicate that the Fe-top site is the most favorable for NO adsorption. The N-O bond length, Mulliken charge, and the N-O vibration frequency of the NO molecule are discussed after adsorption. The analysis results of the density of the states show that when NO is adsorbed with the Fe-NO configuration, the bonding mechanism is mainly from the interaction between the NO and the Fe d orbit.     

Deactivation of Pd particles supported on Nb2O5/Cu3Au(1 0 0): SFG and TPD studies from UHV to 100 mbar

Structural changes that occur on Pd-Nb₂O₅/Cu₃Au(1 0 0) model catalysts upon thermal annealing were followed by sum frequency generation (SFG) and temperature-programmed desorption (TPD) using CO as probe molecule. SFG experiments were performed both under ultrahigh vacuum and mbar pressure. Heating the catalyst to temperatures above 300 K lead to an irreversible 50% decrease in the CO adsorption capacity and modified the remaining adsorption sites. Alterations of the phase between resonant and non-resonant SFG signals upon annealing indicate a change in the electronic structure of the surface, which excludes Pd sintering or migration of Nb₂O₅ over Pd particles to cause the observed effect and rather suggests the formation of “mixed Pd-NbO_x” sites. The same changes in surface properties also occur during CO hydrogenation at 1 bar and high temperature, pointing to an involvement of “mixed Pd-NbO_x” sites in catalytic reactions.     

Hydroxylated α-Al2O3 (0 0 0 1) surfaces and metal/α-Al2O3 (0 0 0 1) interfaces

X-ray photoelectron spectroscopy was applied to study the hydroxylation of α-Al₂O₃ (0 0 0 1) surfaces and the stability of surface OH groups. The evolution of interfacial chemistry of the α-Al₂O₃ (0 0 0 1) surfaces and metal/α-Al₂O₃ (0 0 0 1) interfaces are well illustrated via modifications of the surface O1s spectra. Clean hydroxylated surfaces are obtained through water- and oxygen plasma treatment at room temperature. The surface OH groups of the hydroxylated surface are very sensitive to electron beam illumination, Ar⁺ sputtering, UHV heating, and adsorption of reactive metals. The transformation of a hydroxylated surface to an Al-terminated surface occurs by high temperature annealing or Al deposition.     

Investigation of the interaction of some astrobiological molecules with the surface of a graphite (0 0 0 1) substrate. Application to the CO, HCN, H2O and H2CO molecules

Detailed interaction potential energy calculations are performed to determine the potential energy surface experienced by the molecules CO, HCN, H₂O and H₂CO, when adsorbed on the basal plane (0 0 0 1) of graphite at low temperatures. The potential energy surface is used to find the equilibrium site and configuration of a molecule on the surface and its corresponding adsorption energy. The diffusion constant associated with molecular surface diffusion is calculated for each molecule.     

Interaction of alkali metals with the Fe3O4(1 1 1) Surface

The adsorption and interaction of alkali metals (Li, Na, K, Rb and Cs) with the Fe_tet1-terminated Fe₃O₄(1 1 1) surface have been computed at the level of density functional theory. At low coverage, adsorption of alkali metals on site-1 (O_a-O_c-O_d) is energetically more favorable than on site-2 (O_a-O_c-O_d). Li has the strongest adsorption energy, followed by K, Rb, Cs and Na. The computed net charges show that the alkali metals can donate electrons to surface Fe and O atoms in the order of Li < Na < K ≈ Rb ≈ Cs. It is also noted that increasing the coverage does not significantly improve the promoting effect of alkali metals. In addition, alkali metals can move facilely on the Fe₃O₄(1 1 1) surface.     

The surface structure of Fe3O4(1 1 1) films as studied by CO adsorption

We have studied adsorption of CO on Fe₃O₄(1 1 1) films grown on a Pt(1 1 1) substrate by temperature programmed desorption (TPD), infrared reflection absorption spectroscopy (IRAS) and high resolution electron energy loss spectroscopy (HREELS). Three adsorption states are observed, from which CO desorbs at ∼110, 180, and 230 K. CO adsorbed in these states exhibits stretching frequencies at ∼2115-2140, 2080 and 2207 cm⁻¹, respectively. The adsorption results are discussed in terms of different structural models previously reported. We suggest that the Fe₃O₄(1 1 1) surface is terminated by 1/2 ML of iron, with an outermost 1/4 ML consisting of octahedral Fe²⁺ cations situated above an 1/4 ML of tetrahedral Fe³⁺ ions, in agreement with previous theoretical calculations. The most strongly bound CO is assigned to adsorption to Fe³⁺ cations present on the step edges.     

Initial stages of H2O adsorption and hydroxylation of Fe-terminated α-Fe2O3(0 0 0 1) surface

The adsorption modes of H₂O on a Fe-terminated hematite(0 0 0 1) surface have been investigated by first principles Density Functional theory within a periodic slab model and the generalized gradient approximation. Molecular adsorption and dissociative adsorption in monolayer coverage, one H₂O per surface Fe, were both considered. Five plausible orientations were studied to determine the most favorable adsorption position. Molecular adsorption is shown to have a small effect on the underlying surface structure, while hydroxylation has a strong effect on the surface geometry. Electronic densities of state calculations reveal details of these different interactions. The heterolytic dissociation, which produces two types of surface hydroxyls, is the preferable adsorption mode, being slightly favored energetically over the molecular adsorption. Homolytic dissociative adsorption, forming a single hydroxyl on surface Fe, is energetically unfavored, even though strong binding interaction (∼3 eV) is found between the OH radical and surface. Dissociative adsorption on an oxidized ferryl site was also studied to investigate suggested local reactivity enhancement.     

Density functional theory calculations of surface properties and H2 adsorption on the Cu2O (1 1 1) surface

First-principles calculation on the basis of the density functional theory (DFT) and generalized gradient approximation have been applied to study the adsorption of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1), Cu₂O (1 1 1)-Cu_CUS and Cu-terminated Cu₂O (1 1 1) surfaces. The optimal adsorption position and orientation of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1) surface and Cu-terminated Cu₂O (1 1 1) surface were determined and electronic structural changes upon adsorption were investigated by calculating the Local Density of States (LDOS) of the Cu_CUS 3d and Cu_CUS 4s of stoichiometric O-terminated Cu₂O (1 1 1) surface. These results showed that H₂ molecule adsorption on Cu_CUS site parallel to stoichiometric O-terminated Cu₂O (1 1 1) surface and H₂ molecule adsorption on Cu₂ site parallel to Cu-terminated Cu₂O (1 1 1) surface were the most favored, respectively. The presence of surface copper vacancy has a little influence on the structures when H₂ molecule adsorbs on Cu_CSA, O_CUS and O_CSA atoms and the H₂ molecule is only very weakly bound to the Cu₂O (1 1 1)-Cu_CUS surface. From the analysis of stoichiometric O-terminated Cu₂O (1 1 1) Local Density of States, it is observed that Cu_CUS 3d orbital has moved to a lower energy and the sharp band of Cu_CUS 4s is delocalized when compared to that before H₂ molecule adsorption, and overlapped substantially with bands due to adsorbed H₂ molecule. The Mulliken charges of H₂ adsorption on Cu_CUS site showed that H₂ molecule obtained electron from Cu_CUS which was consistent with the calculated electronic structural changes upon H₂ adsorption.     

First-principles study of La and Sb-doping effects onelectronic structure and optical properties of SrTiO3

The effects of La and Sb doping on the electronic structure and optical properties of SrTiO 3 are investigated by first-principles calculation of the plane wave ultra-soft pseudo-potential based on density functional theory. The calculated results reveal that corner-shared TiO 6 octahedra dominate the main electronic properties of SrTiO 3 , and its structural stability can be improved by La doping. The La 3+ ion fully acts as an electron donor in Sr 0.875 La 0.125 TiO 3 and the Fermi level shifts into the conduction bands (CBs) after La doping. As for SrSb 0.125 Ti 0.875 O 3 , there is a distortion near the bottom of the CBs for SrSb 0.125 Ti 0.875 O 3 after Sb doping and an incipient localization of some of the doped electrons trapped in the Ti site, making it impossible to describe the evolution of the density of states (DOS) within the rigid band model. At the same time, the DOSs of the two electron-doped systems shift towards low energies and the optical band gaps are broadened by about 0.4 and 0.6 eV for Sr0.875La0.125TiO3 and SrSb0.125Ti0.875O3 , respectively. Moreover, the transmittance of SrSb0.125Ti0.875O3 is as high as 95% in most of the visible region, which is higher than that of Sr0.875La0.125TiO3 (85%). The wide band gap, the small transition probability and the weak absorption due to the low partial density of states (PDOS) of impurity in the Fermi level result in the significant optical transparency of SrSb0.125 Ti0.875 O3 .     

Active oxidation of Cu3Au(1 1 0) using hyperthermal O2 molecular beam

Oxidation of Cu₃Au(1 1 0) using a hyperthermal O₂ molecular beam (HOMB) was investigated by X-ray photoemission spectroscopy in conjunction with a synchrotron light source. From the incident energy dependence of the O-uptake curve, the precursor-mediated dissociative adsorption occurs, where the trapped O₂ molecule can migrate and dissociate at the lower activation-barrier sites, dominantly at thermal O₂ exposures. Dissociative adsorption of O₂ on Cu₃Au(1 1 0) is as effective at the thermal O₂ exposure as on Cu(1 1 0). On the other hand, at the incident energies of HOMB where the direct dissociative adsorption is dominant, it was determined that the dissociative adsorption of O₂ implies a higher activation barrier and therefore less reactivity due to the Au alloying in comparison with the HOMB oxidation of Cu(1 1 0). The dissociative adsorption progresses with the Cu segregation on Cu₃Au(1 1 0) similarly as on Cu₃Au(1 0 0). The growth of Cu₂O for 2 eV HOMB suggests that the diffusion of Cu atoms also contribute to the oxidation process through the open face, which makes the difference from Cu₃Au(1 0 0).     

Probing the properties of the (1 1 1) and (1 0 0) surfaces of LaB6 through infrared spectroscopy of adsorbed CO

The adsorption of carbon monoxide on the LaB₆(1 0 0) and LaB₆(1 1 1) surfaces was studied experimentally with the techniques of reflection absorption infrared spectroscopy and X-ray photoelectron spectroscopy. The interaction of CO with the two surfaces was also studied with density functional theory. Both surfaces adsorb CO molecularly at low temperatures but in markedly different forms. On the LaB₆(1 1 1) surface CO initially adsorbs at 90 K in a form that yields a CO stretching mode at 1502-1512 cm⁻¹. With gentle annealing to 120 K, the CO switches to a bonding environment characterized by multiple CO stretch values from 1980 to 2080 cm⁻¹, assigned to one, two, or three CO molecules terminally bonded to the B atoms of a triangular B₃ unit at the (1 1 1) surface. In contrast, on the LaB₆(1 0 0) surface only a single CO stretch is observed at 2094 cm⁻¹, which is assigned to an atop CO molecule bonded to a La atom. The maximum intensity of the CO stretch vibration on the (1 0 0) surface is higher than on the (1 1 1) surface by a factor of 5. This difference is related to the different orientations of the CO molecules on the two surfaces and to reduced screening of the CO dynamic dipole moment on the (1 0 0) surface, where the bonding occurs further from the surface plane. On LaB₆(1 0 0), XPS measurements indicate that CO dissociates on the surface at temperatures above 400 K.