Formation of functional groups on graphite during oxygen plasma treatment

Improved sample wettability was obtained by oxygen plasma functionalization of pyrolytic graphite. The samples were exposed to highly dissociated oxygen plasma with the density of 1 × 10¹⁶ m⁻³, the electron temperature of about 5.5 eV and the density of neutral oxygen atoms of 8 × 10²¹ m⁻³ for 20 s. The surface wettability was measured by a contact angle of water drop. The contact angle dropped from original 112° down to about 1°. The functional groups were detected by XPS analyses. The survey spectrum showed a substantial increase of oxygen concentration on the surface, while high-resolution analyses showed additional oxygen was bonded onto the graphite surface in the form of C-O polar functional group responsible for the increase of the surface energy.     

Chemical synthesis of nanocrystalline SnO2 thin films for supercapacitor application

Nanocrystalline SnO₂ thin films were deposited by simple and inexpensive chemical route. The films were characterized for their structural, morphological, wettability and electrochemical properties using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy techniques (SEM), transmission electron microscopy (TEM), contact angle measurement, and cyclic voltammetry techniques. The XRD study revealed the deposited films were nanocrystalline with tetragonal rutile structure of SnO₂. The FT-IR studies confirmed the formation of SnO₂ with the characteristic vibrational mode of Sn-O. The SEM studies showed formation of loosely connected agglomerates with average size of 5-10 nm as observed from TEM studies. The surface wettability showed the hydrophilic nature of SnO₂ thin film (water contact angle 9°). The SnO₂ showed a maximum specific capacitance of 66 F g⁻¹ in 0.5 Na₂SO₄ electrolyte at 10 mV s⁻¹ scan rate.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Thermal stability and surface acidity of mesoporous silica doubly doped by incorporation of sulfate and zirconium ions

A sulfated Si-Zr-MCM-41 solid with highly ordered mesostructure was synthesized through a templated synthesis route where the CTAB surfactant was used as template. During the synthesis procedure, various amounts of (NH₄)₂SO₄ were added into the mixed solution of Zr and Si precursors to in situ sulfate the MCM-41 solids, aiming to enhance the acidity and thermal stability. The resultant materials showed a long-range ordered hexagonal arrangement with high surface area larger than 797 m²/g and an average pore size distributed at approximate 2.5-2.8 nm. The high-resolution TEM observations confirmed that the order of the mesostructure gained when the molar ratio of SO₄²⁻/(ZrO₂ + SiO₂) increased from 0.1 to 0.3 but decreased as it reached 0.5, which is consistent with the results of ²⁹Si MAS-NMR and XRD analysis. Compared to Si-MCM-41, the (Q² + Q³)/Q⁴ ratio derived from the NMR spectra of the Zr-doped sample was higher, indicating that zirconium atoms were incorporated into the silica framework. Unexpectedly, in situ sulfation does not enhance the surface Brönsted acidity, most likely due to the sulfur retained within the bulk of the materials; however, it indeed improved the thermal stability of the solid and long-range order of the structure.     

The role of adsorption of sodium bis(2-ethylhexyl) sulfosuccinate in wetting of glass and poly(methyl methacrylate) surface

Advancing contact angles, θ, for aqueous solutions of the anionic surfactant, sodium bis(2-ethylhexyl) sulfosuccinate (AOT) were measured on glass and poly(methyl methacrylate) (PMMA) surface. Using the obtained results we determined the properties of aqueous AOT solutions in wetting of these surfaces. It occurs that the wettability of glass and PMMA by these solutions depends on the concentration of AOT in solution. There is almost linear dependence between the contact angle (θ) and concentration of AOT (log C) in the range from 5 × 10⁻⁴ to 2.5 × 10⁻³ M/dm³ (value of the critical micelle concentration of AOT—CMC) both for glass and PMMA surface. For calculations of AOT adsorption at solid (glass, PMMA)-solution drop-air system interfaces the relationship between the adhesion tension (γ_LV cos θ) and surface tension (γ_LV) and the Gibbs and Young equations were taken into account. From the measurement and calculation results the slope of the γ_LV cos θ − γ_LV curve was found to be constant and equal 0.7 for glass and −0.1 for PMMA over the whole range of AOT concentration in solution. From this fact it can be concluded that if Γ_SV is equal zero then Γ_SL > 0 for the PMMA-solution and Γ_SL < 0 for glass-solution systems. It means that surfactant concentration excess at PMMA-solution interface is considerably lower than at solution-air interface, but this excess of AOT concentration at glass-solution interface is lower than in the bulk phase. By extrapolating the linear dependence between the adhesion and surface tension the value of the critical surface tension (γ_c) of wetting for glass and PMMA was also determined, that equaled 25.9 and 25.6 mN/m for glass and PMMA, respectively. Using the value of the glass and PMMA surface tension as well as the measured surface tension of aqueous AOT solutions in Young equation, the solid-liquid interface tension (γ_SL) was found. There was a linear dependence between the γ_SL and γ_LV both for glass and PMMA, but there were different slope values of the curves for glass and PMMA, i.e. −0.7 and 0.1, respectively. The dependence between the work of adhesion (W_A) and surface tension (γ_LV) was also linear of different slopes for glass and for PMMA surface.     

Biocompatibility of polypropylene non-woven fabric membrane via UV-induced graft polymerization of 2-acrylamido-2-methylpropane sulfonic acid

This work described the graft polymerization of a sulfonic acid terminated monomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS), onto the surface of polypropylene non-woven (NWF PP) membrane by O₂ plasma pretreatment and UV-induced photografting method. The chemical structure and composition of the modified surfaces were analyzed by FTIR-ATR and XPS, respectively. The wettability was investigated by water contact angle and equilibrium water adsorption. And the biocompatibility of the modified NWF PP membranes was evaluated by protein adsorption and platelet adhesion. It was found that the graft density increased with prolonging UV irradiation time and increasing AMPS concentration; the water contact angles of the membranes decreased from 124° to 26° with the increasing grafting density of poly(AMPS) from 0 to 884.2 μg cm⁻², while the equilibrium water adsorption raised from 5 wt% to 75 wt%; the protein absorption was effectively suppressed with the introduction of poly(AMPS) even at the low grafting density (132.4 μg cm⁻²); the number of platelets adhering to the modified membrane was dramatically reduced when compared with that on its virgin surface. These results indicated that surface modification of NWF PP membrane with AMPS was a facile approach to construct biocompatible surface.     

Density functional theory investigation of the structure of SO2 and SO3 on Cu(1 1 1) and Ni(1 1 1)

Density functional theory (DFT) slab calculations, mainly using the generalised gradient approximation, have been used to investigate the minimum energy structures of molecular SO₂ and SO₃ on Cu(1 1 1) and Ni(1 1 1) surfaces. On Ni(1 1 1) the optimal local adsorption structures are in close agreement with experimental results for both molecular species obtained using the X-ray standing wavefield technique, although for adsorbed SO₂ the energetic difference between two alternative lateral positions of the lying-down molecule on the surface is marginally significant. On Cu(1 1 1) the results for adsorbed SO₂, in particular, were sensitive to the DFT functional used in the calculations, but in all cases failed to reproduce the experimentally-established preference for adsorption with the molecular plane perpendicular to the surface. This result is discussed in the context of previously published DFT results for these species adsorbed on Cu(1 0 0). The optimal geometry found for SO₃ on Cu(1 1 1) is similar to that on Ni(1 1 1), providing agreement with experiment regarding the molecular orientation but not the adsorption site.     

A DFT study on the formation of CH3O on Cu2O(1 1 1) surface by CH3OH decomposition in the absence or presence of oxygen

The formation mechanism of CH₃O by the adsorption and decomposition of CH₃OH on clean and oxygen-precovered Cu₂O(1 1 1) surface has been investigated with density functional theory method together with the periodic slab models. Two possible formation pathways of CH₃O by CH₃OH decomposition on oxygen-precovered (O_pre) Cu₂O(1 1 1) surface were proposed and discussed. One is the O-H bond-cleavage of CH₃OH with H migration to O_pre to form CH₃O; the other is the C-O bond-scission of CH₃OH with CH₃ migration to O_pre leading to CH₃O_pre. The calculated results show that the O-H bond-breaking path has the lowest activation barrier 26.8 kJ mol⁻¹, the presence of oxygen-precovered on Cu₂O(1 1 1) surface exhibits a high surface reactivity toward the formation of CH₃O by the O-H bond-cleavage of CH₃OH, and reduce the activation barrier of O-H bond-cleavage. The C-O bond-breaking path was inhibited by dynamics, suggesting that the O atom of CH₃O is not from the oxygen-precovered, but comes from the O of CH₃OH. Meanwhile, the calculated results give a clear illustration about the formation mechanism of CH₃O in the presence of oxygen and the role of oxygen at the microscopic level.     

Mechanism of aluminum hydroxide layer formation by surface modification of aluminum

In this study, a new, relatively simple and rapid fabrication method for forming an Al(OH)₃ film on Al substrates was demonstrated. This method, i.e., alkali surface modification, is simply comprised of dipping the substrate in a 5 × 10⁻³ M NaOH solution at 80 °C for 1 min and then immersing it in boiling water for 30 min. After alkali surface modification, an Al(OH)₃ film was formed on Al substrate, and its chemical state and crystal structure were confirmed by XPS and TEM. The Al(OH)₃ layer was composed of three regions: an amorphous-rich region, a region of mixed amorphous and crystal domains, and a crystalline-rich region near the Al(OH)₃ layer surface.     

Characterization of mesoporous VOx/MCM-41 composite materials obtained via post-synthesis impregnation

Spherical-particle MCM-41 was synthesized at room temperature, and, then, impregnated with aqueous solutions of NH₄VO₃ to produce variously loaded VO_x/MCM-41 composite materials. Bulk and surface properties of the materials thus produced were characterized by means of X-ray powder diffractometry (XRD), infrared spectroscopy (FTIR), N₂ sorptiometry and X-ray photoelectron spectroscopy (XPS). Results obtained indicated that subsequent calcination at 550 °C (for 2 h) of the blank and impregnated MCM-41 particles, results in materials assuming the same bulk structure of MCM-41, and exposing uniformly mesporous, high area surfaces (P_w = 2.0-2.3 nm; 974-829 m²/g), except for the material obtained at 20 wt%-V₂O₅ that was shown to suffer a considerable loss on surface area (down to 503 m²/g). XPS results implied that the immobilization of the VO_x species occurs via interaction with surface OH/H₂O groups of MCM-41, leading to the formation of vanadate (VO₃⁻) surface species, as well as minor V-O-Si and V₂O₅-like species. However, in all cases, the vanadium sites remained pentavalent and exposed on the surface.     

Hydroxylated α-Al2O3 (0 0 0 1) surfaces and metal/α-Al2O3 (0 0 0 1) interfaces

X-ray photoelectron spectroscopy was applied to study the hydroxylation of α-Al₂O₃ (0 0 0 1) surfaces and the stability of surface OH groups. The evolution of interfacial chemistry of the α-Al₂O₃ (0 0 0 1) surfaces and metal/α-Al₂O₃ (0 0 0 1) interfaces are well illustrated via modifications of the surface O1s spectra. Clean hydroxylated surfaces are obtained through water- and oxygen plasma treatment at room temperature. The surface OH groups of the hydroxylated surface are very sensitive to electron beam illumination, Ar⁺ sputtering, UHV heating, and adsorption of reactive metals. The transformation of a hydroxylated surface to an Al-terminated surface occurs by high temperature annealing or Al deposition.     

The role of co-adsorbed O2 on the catalytic reduction of NO with C2H5OH on the surface of Pt(3 3 2)

The influence of pre-dosed O₂ on the catalytic reduction of NO with ¹³C₂H₅OH on the surface of stepped Pt(3 3 2) was investigated using Fourier transform infra red reflection-absorption spectroscopy (FTIR-RAS) and thermal desorption spectroscopy (TDS). We show that the oxidation of ¹³C₂H₅OH with O₂ is a very effective reaction, occurring at 150 K and giving rise to acetate. The presence of NO does not lead to any evident oxidation of ¹³C₂H₅OH irrespective of the annealing temperature. For the case of O₂ + ¹³C₂H₅OH + NO co-adlayers, oxidation of ¹³C₂H₅OH also takes place at 150 K. However, no new surface species that are supposed to be an intermediate for the production of N₂ are detected.The influence of O₂ on the production and desorption of N₂ is intimately related to both O₂ and ¹³C₂H₅OH coverage. The presence of pre-dosed O₂ does not greatly promote N₂ desorption. In fact, N₂ desorption is suppressed quantitatively with increasing O₂ coverage, after which unreacted, or left-over O atoms appear and remain on steps. It is concluded that the presence of pre-dosed O₂ does not play a role of activating reactants in the catalytic reduction of NO with ¹³C₂H₅OH on the surface of Pt(3 3 2).     

The corrosion inhibition and gas evolution studies of some surfactants and citric acid on lead alloy in 12.5 M H2SO4 solution

The inhibition action of the citric acid and three surfactants: sodium dodecyl sulfate (SDS), t-octyl phenoxy polyethoxyethanol (Triton X-100), sodium dodecyl benzene sulphonate (SDBS) on the corrosion behavior and gas evolution of Pb-Sb-As-Se was investigated in 12.5 M H₂SO₄ solution with linear sweep polarization, cyclic voltammetry and weight loss measurements methods. The results drawn from different techniques are comparable. It was found that these surfactants and citric acid act as good inhibitors for the corrosion of lead alloy in H₂SO₄ solution. SDS inhibited most effectively the lead alloy corrosion among the three surfactants and citric acid. The inhibition efficiency for the inhibitors decreases in the order: SDS > SDBS > Triton X-100 > citric acid > blank. The inhibition efficiency increases with rising of the inhibitor concentration. In this work, the effect of the inhibitors on hydrogen and oxygen evolution was studied. In addition, it was found that the adsorption of used inhibitors on lead alloy surface follows Langmuir isotherm.     

Adsorption and reactivity of SO2 on Ir(1 1 1) and Rh(1 1 1)

The adsorption and reactivity of SO₂ on the Ir(1 1 1) and Rh(1 1 1) surfaces were studied by surface science techniques. X-ray photoelectron spectroscopy measurements showed that SO₂ was molecularly adsorbed on both the Ir(1 1 1) surface and the Rh(1 1 1) surface at 200 K. Adsorbed SO₂ on the Ir(1 1 1) surface disproportionated to atomic sulfur and SO₃ at 300 K, whereas adsorbed SO₂ on the Rh(1 1 1) surface dissociated to atomic sulfur and oxygen above 250 K. Only atomic sulfur was present on both surfaces above 500 K, but the formation process and structure of the adsorbed atomic sulfur on Ir(1 1 1) were different from those on Rh(1 1 1). On Ir(1 1 1), atomic sulfur reacted with surface oxygen and was completely removed from the surface, whereas on Rh(1 1 1), sulfur did not react with oxygen.     

Investigation of etch characteristics of non-polar GaN by wet chemical etching

We characterized the surface defects in a-plane GaN, grown onto r-plane sapphire using a defect-selective etching (DSE) method. The surface morphology of etching pits in a-plane GaN was investigated by using different combination ratios of H₃PO₄ and H₂SO₄ etching media. Different local etching rates between smooth and defect-related surfaces caused variation of the etch pits made by a 1:3 ratio of H₃PO₄/H₂SO₄ etching solution. Analysis results of surface morphology and composition after etching by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) demonstrated that wet chemical etching conditions could show the differences in surface morphology and chemical bonding on the a-plane GaN surface. The etch pits density (EPD) was determined as 3.1 × 10⁸ cm⁻² by atom force microscopy (AFM).     

Study of surface interactions of ionic liquids with aluminium alloys in corrosion and erosion-corrosion processes

Surface interactions of alkylimidazolium ionic liquids (ILs) with aluminium alloy Al 2011 have been studied by immersion tests in seven neat ILs [1-n-alkyl-3-methylimidazolium X⁻ (X = BF₄; n = 2 (IL1), 6 (IL2), 8 (IL3). X = CF₃SO₃; n = 2 (IL4). X = (4-CH₃C₆H₄SO₃); n = 2 (IL5). X = PF₆; n = 6 (IL6)] and 1-butyl-3-methylpyridinium bis(trifluoromethylsulfonyl)imide (IL7)]. Immersion tests for Al 2011 have also been carried out in 1 wt.% and 5 wt.% solutions of 1-ethyl,3-methylimidazolium tetrafluoroborate (IL1) in water. No corrosion of Al 2011 by neat ILs is observed. The highest corrosion rate for Al 2011 in water is observed in the presence of a 5 wt.% IL1 due to hydrolysis of the anion with hydrogen evolution and formation of aluminium fluoride. Erosion-corrosion processes have been studied for three aluminium alloys (Al 2011, Al 6061 and Al 7075) in a 90 wt.% IL1 solution in water in the presence of α-alumina particles. The erosion-corrosion rates are around 0.2 mm/year or lower, and increase with increasing copper content to give a corrosion resistance order of Al 6061 > Al 7075 > Al 2011. Results are discussed on the basis of scanning electron microscopy (SEM) observations, energy dispersive spectroscopy (EDS) analysis, X-ray diffraction (XRD) patterns and X-ray photoelectron spectroscopy (XPS) determinations.     

Theoretical study on the kinetics for OH reactions with CH3OH and C2H5OH

Kinetics and mechanisms for reactions of OH with methanol and ethanol have been investigated at the CCSD(T)/6-311 + G(3df, 2p)//MP2/6-311 + G(3df, 2p) level of theory. The total and individual rate constants, and product branching ratios for the reactions have been computed in the temperature range 200-3000 K with variational transition state theory by including the effects of multiple reflections above the wells of their pre-reaction complexes, quantum-mechanical tunneling and hindered internal rotations. The predicted results can be represented by the expressions k₁ = 4.65 × 10⁻²⁰ × T^2.68 exp(414/T) and k₂ = 9.11 × 10⁻²⁰ × T^2.58 exp(748/T) cm³ molecule⁻¹ s⁻¹ for the CH₃OH and C₂H₅OH reactions, respectively. These results are in reasonable agreements with available experimental data except that of OH + C₂H₅OH in the high temperature range. The former reaction produces 96-89% of the H₂O + CH₂OH products, whereas the latter process produces 98-70% of H₂O + CH₃CHOH and 2-21% of the H₂O + CH₂CH₂OH products in the temperature range computed (200-3000 K).     

Modification of multi-walled carbon nanotubes for electric double-layer capacitors: Tube opening and surface functionalization

Multi-walled carbon nanotubes (MWCNTs) obtained opening the closed ends and using surface functionalization by means of a combination of partial oxidation in air and chemical modifications are characterized systematically in 0.3 M H₂SO₄ between 0 and 1.0 V, and these nanotubes were planned to be used as electrode materials in electric double-layer capacitors (EDLCs). Opening of MWCNTs, clearly observed by means of transmission electron microscopy (TEM), can be easily achieved by the partial oxidation in air through a seven-step temperature program identified by thermogravimetric/differential thermal analyses (TG/DTA). An increase in 175% specific capacitance is obtained for the MWCNTs, partially oxidized in air and chemically modified in H₂SO₄+HNO₃. The temperature-programmed desorption (TPD) data showed that evolutions of CO and CO₂ are, respectively, promoted by the application of partial oxidation in air and chemical modification in H₂SO₄+HNO₃. The above increase in specific capacitance for modified MWCNTs is attributed to an obvious increase in the BET surface area (double-layer capacitance) and the density of oxygen-containing surface functional groups (pseudocapacitance).     

Global SO(3) × SO(3) × U(1) symmetry of the Hubbard model on bipartite lattices

In this paper the global symmetry of the Hubbard model on a bipartite lattice is found to be larger than SO(4). The model is one of the most studied many-particle quantum problems, yet except in one dimension it has no exact solution, so that there remain many open questions about its properties. Symmetry plays an important role in physics and often can be used to extract useful information on unsolved non-perturbative quantum problems. Specifically, here it is found that for on-site interaction U ≠ 0 the local SU(2) × SU(2) × U(1) gauge symmetry of the Hubbard model on a bipartite lattice with N_a^D sites and vanishing transfer integral t = 0 can be lifted to a global [SU(2) × SU(2) × U(1)]/Z₂² = SO(3) × SO(3) × U(1) symmetry in the presence of the kinetic-energy hopping term of the Hamiltonian with t > 0. (Examples of a bipartite lattice are the D-dimensional cubic lattices of lattice constant a and edge length L = N_aa for which D = 1, 2, 3,... in the number N_a^D of sites.) The generator of the new found hidden independent charge global U(1) symmetry, which is not related to the ordinary U(1) gauge subgroup of electromagnetism, is one half the rotated-electron number of singly occupied sites operator. Although addition of chemical-potential and magnetic-field operator terms to the model Hamiltonian lowers its symmetry, such terms commute with it. Therefore, its 4^N_aD energy eigenstates refer to representations of the new found global [SU(2) × SU(2) × U(1)]/Z₂² = SO(3) × SO(3) × U(1) symmetry. Consistently, we find that for the Hubbard model on a bipartite lattice the number of independent representations of the group SO(3) × SO(3) × U(1) equals the Hilbert-space dimension 4^N_aD. It is confirmed elsewhere that the new found symmetry has important physical consequences.     

The local structure of SO2 and SO3 on Ni(1 1 1)

The normal incidence X-ray standing wave (NIXSW) technique, supported by X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure (NEXAFS), has been used to determine the local adsorption geometry of SO₂ and SO₃ on Ni(1 1 1). Chemical-state specific NIXSW data for coadsorbed SO₃ and S, formed by the disproportionation of adsorbed SO₂ after heating from 140 K to 270 K, were obtained using S 1s photoemission detection. For adsorbed SO₂ at 140 K the new results confirm those of an earlier study [Jackson et al., Surf. Sci. 389 (1997) 223] that the molecule is located above hollow sites with its molecular plane parallel to the surface and the S and O atoms in off-atop sites; corrections to account for the non-dipole effects in the interpretation of the NIXSW monitored by S 1s and O 1s photoemission, not included in the earlier work, remove the need for any significant adsorption-induced distortion of the SO₂ in this structure. SO₃, not previously investigated, is found to occupy an off-bridge site with the C_3v axis slightly tilted relative to the surface normal and with one O atom in an off-atop site and the other two O atoms roughly between bridge and hollow sites. The O atoms are approximately 0.87 Å closer to the surface than the S atom. This general bonding orientation for SO₃ is similar to that found on Cu(1 1 1) and Cu(1 0 0) both experimentally and theoretically, although the detailed adsorption sites differ.