Humidity sensing properties of Pd-doped ZnO nanotetrapods

Pd²⁺-doped ZnO nanotetrapods were prepared and studied for the humidity detection application. The humidity sensors developed were featured by combination of a quartz crystal microbalance (QCM) as a transducer and Pd²⁺-doped ZnO nanotetrapods as a sensing element. The ZnO nanotetrapods were synthesized by evaporating highly pure zinc pellets (99.999%) at 900 °C in air and PdCl₂ was doped on by traditional solution mixing process. Then the mixed solution distributed onto the electrode surfaces of the quartz crystal at room temperature. Pd²⁺-doped ZnO nanotetrapods were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The experimental results indicated that the response of the sensors varied with the different dosage PdCl₂. Linear regression algorithm was used for evincing the highly linear behavior of the Pd²⁺-doped ZnO nanotetrapods sensor. In this humidity sensing system, the Pd²⁺-doped ZnO nanotetrapods sensing material coated on the gold electrode of QCM showed good sensitivity (∼74.24324 Hz/%RH (relative humidity)), reproducibility, linearity (R² = −0.98834), short response and recovery time (less than 5 s).     

Effects of hydrogen flux on the properties of Al-doped ZnO films sputtered in Ar + H2 ambient at low temperature

Al-doped ZnO (AZO) transparent conductive thin films were grown by magnetron sputtering with AZO (98 wt.% ZnO, 2 wt.% Al₂O₃) ceramic target in Ar + H₂ ambient at a relatively low temperature of 100 °C. To investigate the dependence of crystalline and properties of as-grown AZO films on the H₂-flux, X-ray diffraction (XRD), X-ray photoemission spectrometer (XPS), Hall and transmittance spectra measurements were employed to analyze the AZO samples deposited with different H₂-flux. The results indicate that H₂-flux has a considerable influence on the transparent conductive properties of AZO films. The resistivity of 4.15 × 10⁻⁴ Ω cm and the average transmittance of more than 94% in the visible range were obtained with the optimal H₂-flux of 1.0 sccm. Such a low temperature growing method present here may be especially useful for some low-melting point photoelectric devices and substrates.     

Study of the Rod-Like and spherical nano-ZnO morphology on H2S removal from natural gas

The purpose of this work is to study the adsorption of H₂S from gas streams containing He and CH₄ with an emphasis on the influence of the sorbent morphology on the process of adsorption. As an example of the approach, a unique modified nano-ZnO sample with a Rod-like morphology was fabricated and comparatively studied together with a nano-spherical ZnO sample under various conditions. The objective was accomplished applying central composite design (CCD) in order to screen the effects of significant adsorption parameters obtained by Placket-Burman design. Morphology of the sorbent, temperature, space velocity and H₂S feed concentration were initially evaluated. Placket-Burman design experiments showed a wide deviation of adsorption capacity of 0.03-0.24 g H₂S/g ZnO. Results indicated that comparing other parameters Rod like morphology comparing spherical, had significant effect on all four independent H₂S adsorption parameters. Besides that, space velocity and H₂S feed concentration were found to be effective parameters on adsorption of hydrogen sulfide in the range of 4000-8000 h⁻¹ and 0.5-1 mol% respectively. Moreover, experiments revealed a negligible effect of adsorption temperature in range of 150-250 °C. The optimized condition obtained a dynamic capacity of 0.2401 g H₂S/g ZnO at space velocity 4000 h⁻¹ and H₂S feed concentration of 1 mol%. Proceeding our study by significant parameters, analysis of variance (ANOVA) displayed a high coefficient of determination (R²) value of 0.931-0.959, indicating the satisfactory adjustment of the quadratic model.     

Hydrogen sensors based on ZnO nanoparticles

Hydrogen sensing characteristics of thick films of nanoparticles (∼35 nm diameter) of ZnO, 3% Co doped ZnO, 1% Pt-impregnated ZnO and 1% Pt-impregnated 3% Co-ZnO have been investigated. The last composition exhibits the highest sensitivity for 10-1000 ppm H₂, reaching values upto 1700 as well as good response and recovery times at 125 °C or lower. The sensor is not affected significantly upto 50% relative humidity.     

Studies of structural evolution and sensing properties of ZnO nanocrystalline films

ZnO nanocrystalline films have been prepared on Si(1 0 0) substrate using direct current (D.C) magnetron sputtering technique at room temperature. The thickness of nanocrystalline films almost linearly increased with deposition duration and the sizes of crystalline grains almost kept unchanged. After deposition, thermal annealing was performed at 800 °C in atmosphere for 2 h in order to improve the qualities of ZnO thin films. Scanning electron microscope (SEM) images showed the surface roughness of the films less than 45 nm. X-ray diffraction (XRD) patterns revealed the slight evolution of the crystal structures. Raman scattering spectra confirmed the data obtained from X-ray diffraction measurements.With these ZnO nanocrystalline films, prototypic gas sensors were fabricated. Both sensitivity and response of the sensors to different gases (H₂ and CH₄) were investigated. A quick response of time, less than 1 second to CH₄ gas sensor has been achieved.     

The effect of surface morphology on the response of Fe2O3-loaded vanadium oxide nanotubes gas sensor

The effect of surface morphology on the response of an ethanol sensor based on vanadium nanotubes surface loaded with Fe₂O₃ nanoparticles (Fe₂O₃/VONTs) was investigated in this work. The particle size of Fe₂O₃ loaded on VONTs was varied by using novel citric acid-assisted hydrothermal method. In the synthesis progress, citric acid was used as a surfactant and chelate agent, which ensured the growth of a uniform Fe₂O₃ loading on the nanotubes surface. The ethanol sensing properties was then measured for these Fe₂O₃/VONTs at 230-300 °C. The results showed that the sensor response increased with the particles size and the loading amount of Fe₂O₃. It appears that the load of Fe₂O₃ on the VONTs surface increases the concentration of oxygen vacancies and decreases the concentration of free electrons. The effects of morphology on the sensor resistance were interpreted in terms of the Debye length and the difference in the number of active sites.     

The gas response enhancement from ZnO film for H2 gas detection

ZnO thin films were prepared by thermal oxidation of Zn metal at 400 °C for 30 and 60 min. The XRD results showed that the Zn metal was completely converted to ZnO with a polycrystalline structure. The sensors had a maximum response to H₂ at 400 °C and showed stable behavior for detecting H₂ gases in the range of 40 to 160 ppm. The film oxidized for 60 min in oxygen flow exhibited higher response than that of the 30 min oxidation which was approximately 4000 for 160 ppm H₂ gas concentration. The sensing mechanism was modeled according to the oxygen-vacancy model.     

Application of ultrasonic wave to clean the surface of the TiO2 nanotubes prepared by the electrochemical anodization

In this study, the TiO₂ nanotubes were fabricated by electrochemical anodization in a NH₄F/Na₂SO₄/PEG400/H₂O electrolyte system. Ultrasonic wave (80 W, 40 kHz) was used to clean the surface of TiO₂ nanotube arrays in the medium of water after the completion of the anodization. Surface morphology (FESEM) and X-ray diffraction spectrum of the nanotubes treated by sonication at 0 min, 9 min, 40 min and 60 min were compared. The experimental results showed that the precipitate on the surface of the nanotube arrays could be removed by the ultrasonic wave. The treating time had an influence on the precipitate removal and 9 min (corresponding to 12 Wh) is the suitable time for surface cleaning of the TiO₂ nanotubes on this experimental condition.     

Twinned tabour-like ZnO: Surfactant-, template-free synthesis and gas sensing behaviors

The twinned tabour-like ZnO microstructures have been successfully synthesized via a solvothermal method without the assistant of any additive and template. The as-prepared products are characterized by X-ray diffraction, field emission scanning electron microscope, and high-resolution transmission electron microscope. The ZnO microcrystals grow symmetrically, and are wurtzite structure. The tabour, with a diameter of about 8.5 μm, grows along the c axis. The time-dependent morphology evolution of the ZnO microcrystal presents every single ZnO tabour is composed by many single crystal units. A possible formation mechanism of these complex hierarchical structures is investigated by adjusting the reaction time. In addition, the twinned ZnO tabours exhibit excellent ethanol-sensing properties at 250 °C. The highest response is 6.4-20 ppm ethanol. The response of the sensor rapidly increases with the increasing concentration of ethanol, until the ethanol reaching 200 ppm. The response of the sensor to 200 ppm ethanol is about 24.64 with the response time of 3 s.     

Photoluminescence from ZnO-SiO2 opals with different sphere diameters and thicknesses

We systematically investigated the photoluminescence (PL) and transmittance characteristics of ZnO-SiO₂ opals with varied positions of the stop-band and film thicknesses. An improved ultraviolet (UV) luminescence was observed from ZnO-SiO₂ composites over pure ZnO nanocrystals under 325 nm He-Cd laser excitation at room temperature. The UV PL of ZnO nanocrystals in SiO₂ opals with stop-bands center of 410 nm is sensitive to the thickness of opal films, and the UV PL intensity increases with the film thickness increasing. The PL spectra of ZnO nanocrystals in SiO₂ opals with stop-bands center of 570 nm show a suppression of the weak visible band. The experimental results are discussed based on the scattering and/or absorbance in opal crystals.     

Conversion of p-type to n-type conductivity in undoped ZnO films by increasing operating temperature

ZnO thin films with the thickness of about 15 nm on (0 0 0 1) sapphire substrates were prepared by pulsed laser deposition. X-ray photoelectron spectroscopy indicated that both as-grown and post-annealed ZnO thin films were oxygen-rich. H₂ sensing measurements of the films indicated that the conductivity type of both the unannealed and annealed ZnO films converted from p-type to n-type in process of increasing the operating temperature. However, the two films showed different conversion temperatures. The origin of the p-type conductivity in the unannealed and annealed ZnO films should be attributed to oxygen related defects and zinc vacancies related defects, respectively. The conversion of the conductivity type was due to the annealing out of the correlated defects. Moreover, p-type ZnO films can work at lower temperature than n-type ZnO films without obvious sensitivity loss.     

Theoretical study on the kinetics for OH reactions with CH3OH and C2H5OH

Kinetics and mechanisms for reactions of OH with methanol and ethanol have been investigated at the CCSD(T)/6-311 + G(3df, 2p)//MP2/6-311 + G(3df, 2p) level of theory. The total and individual rate constants, and product branching ratios for the reactions have been computed in the temperature range 200-3000 K with variational transition state theory by including the effects of multiple reflections above the wells of their pre-reaction complexes, quantum-mechanical tunneling and hindered internal rotations. The predicted results can be represented by the expressions k₁ = 4.65 × 10⁻²⁰ × T^2.68 exp(414/T) and k₂ = 9.11 × 10⁻²⁰ × T^2.58 exp(748/T) cm³ molecule⁻¹ s⁻¹ for the CH₃OH and C₂H₅OH reactions, respectively. These results are in reasonable agreements with available experimental data except that of OH + C₂H₅OH in the high temperature range. The former reaction produces 96-89% of the H₂O + CH₂OH products, whereas the latter process produces 98-70% of H₂O + CH₃CHOH and 2-21% of the H₂O + CH₂CH₂OH products in the temperature range computed (200-3000 K).     

Field emission properties of carbon nanotubes grown on silicon nanowire arrays

Carbon nanotubes are synthesized on the silicon nanowire arrays which are fabricated on silicon substrate by chemical vapor depositing SiCl₄ and H₂ gases in the presence of Au catalysts. The silicon nanowires are single-crystal with lengths up to 100 μm and diameters ranging from 50 to 500 nm. The tangled carbon nanotubes are grown directly from the surface of Si nanowires. The field emission properties of the carbon nanotubes are investigated at the gap of 200 μm. The low turn on and threshold fields are obtained. The stabilization of the emission currents is also presented.     

Low-temperature growth and ethanol-sensing characteristics of quasi-one-dimensional ZnO nanostructures

ZnO nanorods, nanobelts, nanowires, and tetrapod nanowires were synthesized via thermal evaporation of Zn powder at temperatures in the range 550-600 °C under flow of Ar or Ar/O₂ as carrier gas. Uniform ZnO nanowires with diameter 15-25 nm and tetrapod nanowires with diameter 30-50 nm were obtained by strictly controlling the evaporation process. Our experimental results revealed that the concentration of O₂ in the carrier gas was a key factor to control the morphology of ZnO nanostructures. The gas sensors fabricated from quasi-one-dimensional (Q1D) ZnO nanostructures exhibited a good performance. The sensor response to 500 ppm ethanol was up to about 5.3 at the operating temperature 300 °C. Both response and recovery times were less than 20 s. The gas-sensing mechanism of the ZnO nanostructures is also discussed and their potential application is indicated accordingly.     

Influence of growth temperature of TiO2 buffer on structure and PL properties of ZnO films

A series of ZnO films with TiO₂ buffer on Si (1 0 0) substrates were prepared by DC reactive sputtering. Growth temperature of TiO₂ buffer changed from 100 °C to 400 °C, and the influence on the crystal structures and optical properties of ZnO films have been investigated. The XRD results show that the ZnO films with TiO₂ buffer have a hexagonal wurtzite structure with random orientation, and with the increase of growth temperature of TiO₂ buffer, the residual stresses were released gradually. Specially, the UV emission enhanced distinctly and FWHMs (full width half maximum) decreased linearly with the increasing TiO₂ growth temperature. The results all come from the improvement of crystal quality of ZnO films.     

Synthesis and performance of core-shell structured ZnO/In2O3 composites in situ growth

Core-shell structured ZnO/In₂O₃ composites were successfully synthesized via situ growth method. Phase structure, morphology, microstructure and property of the products were investigated by X-ray diffraction (XRD), TG-DTA, field emission scanning electron microscopy (FESEM), energy-dispersive spectrometry (EDS), transmission electron microscope (TEM) and photoluminescence (PL). Results show that the core-shell structures consist of spindle-like ZnO with about 800 nm in length and 200 nm in diameter, and In₂O₃ particles with a diameter of 50 nm coated on the surface of ZnO uniformly. HMTA plays an important role in the formation of core-shell structures and the addition of In₂O₃ has a great effect on PL spectrum. Possible mechanism for the formation of core-shell structures is also proposed in this paper.     

Optical properties of zinc peroxide and zinc oxide multilayer nanohybrid films

Zinc peroxide and zinc oxide nanoparticles were prepared and self-assembled hybrid nanolayers were built up using layer-by-layer (LbL) technique on the surface of glass substrate using the layer silicate hectorite and an anionic polyelectrolyte, sodium polystyrene sulfonate (PSS). Light absorption, interference and morphological properties of the hybrid films were studied to determine their thickness and refractive index. The influence of layer silicates and polymers on the self-organizing properties of ZnO₂ and ZnO nanoparticles was examined. X-ray diffraction revealed that ZnO₂ powders decomposed to ZnO (zincite phase) at relatively low temperatures (less than 200 °C). The optical thickness of the films ranged from 190 to 750 nm and increased linearly with the number of layers. Band gap energies of the ZnO₂/hectorite films were independent from the layer thickness and were larger than that of pure ZnO₂ nanodispersion. Decomposition of ZnO₂ to ZnO and O₂ at 400 °C resulted in the decrease of the band gap energy from 3.75 to 3.3 eV. Concomitantly, the refractive index increased in correlation with the formation of the zincite ZnO phase. In contrast, the band gap energies of the ZnO₂/PSS hybrid films decreased with the thickness of the nanohybrid layers. We ascribe this phenomenon to the steric stabilization of primary ZnO₂ particles present in the confined space between adjacent layers of hectorite sheets.     

Morphology transition of ZnO films with DMZn flow rate in MOCVD process

We used a metal-organic chemical vapor deposition (MOCVD) method to grow ZnO films on MgAl₂O₄ (1 1 1) substrate, and succeeded in preparing films with microstructures from well-aligned ZnO nanorods to continuous and dense films by adjusting the ratio of the input rates of oxygen and zinc sources (VI/II). At the growth temperature of 350 °C, the ZnO nanorods were formed under a low flow rate of a zinc precursor. On the other hand, continuous and dense ZnO films were formed under a high flow rate of the zinc precursor. There is a transition zone at medium zinc precursor flow rate, where nanorods transform to dense films. We proved that the height of ZnO nanorods and the thickness of ZnO dense films both increase with zinc flow rate, and are consistent with the mass-transport mechanism for ZnO growth. The XRD spectra of the sample in the transition zone show both (0 0 2) and (1 0 1) peaks, where (1 0 1) peaks are formed only in the transition zone. We consider that there are (0 0 2) and (1 0 1) ZnO grains in the early growth stage of dense ZnO films.     

Photoluminescence observations of hydrogen incorporation and outdiffusion in ZnO thin films

ZnO thin films were deposited with the addition of H₂ to the reaction gas using the atmospheric-pressure metal organic chemical vapor deposition method. The incorporation and outdiffusion of hydrogen in ZnO films were investigated by comparing the intensity of the hydrogen-related bound-exciton peak (I₄: 3.363 eV) in the photoluminescence spectrum. The intensity of I₄ peak was found to be the strongest in the ZnO film deposited at 680 °C with H₂ present. However, for the ZnO films prepared at the same temperature 680 °C but without H₂ present and at the higher temperature of 900 °C with H₂ present, respectively, the I₄ peak was just a minor shoulder of another bound-exciton peak (I₈: 3.359 eV). The intensity of I₄ peak in the ZnO films deposited with H₂ present was found to decrease with the increasing of annealing temperature. These results suggest that it is difficult for hydrogen to incorporate into ZnO thin films grown at high temperatures even in the hydrogen-present ambient.     

Structural, electrical and optical properties of Ga-doped ZnO films on PET substrate

The effects of O₂ plasma pretreatment on the properties of Ga-doped ZnO films on PET substrate were studied. Ga-doped ZnO films were fabricated by RF magnetron sputtering process. To improve surface energy and adhesion of PET substrate, O₂ plasma pretreatment process was used prior to GZO sputtering. With increasing O₂ plasma treatment time, the contact angle decreases and the RMS surface roughness increases significantly. The transmittance of GZO films on PET substrate in a wavelength of 550 nm was 70-84%. With appropriate O₂ plasma treatment, the resistivity of GZO films on PET substrate was 3.4 × 10⁻³ Ω cm.