浸渍-分解法制备高可见光催化活性的Bi2O3/TiO2纳米管阵列

用浸渍-分解法将Bi₂O₃纳米颗粒沉积在TiO₂纳米管壁上, 制备了Bi₂O₃/TiO₂纳米管阵列. 用电感耦合等离子体发射光谱(ICP-AES)测定了Bi₂O₃/TiO₂ 纳米管阵列的化学组分, 利用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 通过在可见光下(λ>400 nm)降解甲基橙(MO)水溶液来评价样品的光催化活性. 结果表明, Bi₂O₃纳米颗粒均匀地沉积在TiO₂纳米管中. Bi₂O₃/TiO₂纳米管阵列具有比纯Bi₂O₃膜和N-TiO₂纳米管阵列高得多的可见光催化活性. Bi₂O₃/TiO₂纳米管阵列活性的增强是其强可见光吸收和Bi₂O₃与TiO₂之间形成的异质结的协同作用的结果.     

不同晶型Bi2O3可见光光催化降解罗丹明B的研究

采用化学沉淀法制备了α、β、γ 3种晶体结构的Bi₂O₃光催化剂。利用XRD、TEM、氮气吸附、TG-DSC、紫外-可见漫反射光谱对样品的晶体结构、微观形貌、光学吸收特性进行了表征,并以罗丹明B(RhB)作为模型污染物,研究了不同的粉体光催化剂在可见光(λ>420 nm)照射下的光催化能力。结果表明：制备的α-Bi₂O₃为长3 μm、宽1 μm的板条状颗粒,带隙为2.84 eV;β-Bi₂O₃为粒径约150 nm的不规则颗粒,带隙为2.75 eV;γ-Bi₂O₃为直径6 nm、长度150~200 nm的纳米管,带隙为2.68 eV。在可见光照射下Bi₂O₃光催化降解RhB的活性如下：γ-Bi₂O₃>β-Bi₂O₃>α-Bi₂O₃,其中γ-Bi₂O₃在辐照60 min后对罗丹明B的脱色率可达97%以上。     

Structural and electrical properties of the 2Bi2O3·3ZrO2 system

Powder mixtures of α-Bi₂O₃ (bismite) and monoclinic m-ZrO₂ (baddeleyite) in the molar ratio 2:3 were mechanochemically and thermally treated with the goal to examine the phases, which may appear during such procedures. The prepared samples were characterized by X-ray powder diffraction, differential scanning calorimetry (DSC), electrical measurements, as well as scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The mechanochemical reaction leads to the gradual formation of a nanocrystalline phase, which resembles δ-Bi₂O₃, a high-temperature Bi₂O₃ polymorph. Isothermal sintering in air at a temperature of 820 °C for 24 h followed by quenching to room temperature yielded a mixture of ZrO₂-stabilized β-Bi₂O₃ and m-ZrO₂ phases, whereas in slowly cooled products, the complete separation of the initial α-Bi₂O₃ and m-ZrO₂ constituents was observed. The dielectric permittivity of the sintered samples significantly depended on the temperature. The sintered and quenched samples exhibited a hysteresis dependence of the dielectric shift, showing that the ZrO₂-doped β-Bi₂O₃ phase possess ferroelectric properties, which were detected for the first time. This fact, together with Rietveld refinement of the β-Bi₂O₃/m-ZrO₂ mixture based on neutron powder diffraction data showed that ZrO₂-doped β-Bi₂O₃ has a non-centrosymmetric structure with as the true space group. The ZrO₂ content in the doped β-Bi₂O₃ and the crystal chemical reasons for the stabilization of the β-Bi₂O₃ phase by the addition of m-ZrO₂ are discussed.     

四角星形BiVO4/Bi2O3催化剂的制备及性能

采用水热法合成具有四角星形貌的钒酸铋,再将钒酸铋浸渍在碱溶液里二次水热,制备出BiVO_4/Bi_2O_3催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM),紫外-可见漫反射(UV-Vis DRS)等方法对样品进行表征。可见光下,BiVO_4/Bi_2O_3复合物的光催化降解罗丹明B性能及光电流响应均优于纯BiVO_4。这是由于BiVO_4/Bi_2O_3复合材料形成了异质结构,有效抑制了光生电子与空穴的复合效率。     

四角星形BiVO4/Bi2O3催化剂的制备及性能研究

采用水热法合成具有四角星形貌的钒酸铋,再将钒酸铋浸渍在碱溶液里二次水热,制备出BiVO₄/Bi₂O₃催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM),紫外-射(UV-Vis DRS)等方法征。可见光下,BiVO₄/Bi₂O₃复合物的光催化降解丹明B性能及光电优于纯BiVO₄。BiVO₄/Bi₂O₃复合材料形成了异质结构,有效抑制了光电子与空穴的复合效率。     

Phase formation, crystal chemistry, and properties in the system Bi2O3-Fe2O3-Nb2O5

Subsolidus phase relations have been determined for the Bi₂O₃-Fe₂O₃-Nb₂O₅ system in air (900-1075 °C). Three new ternary phases were observed—Bi₃Fe_0.5Nb_1.5O₉ with an Aurivillius-type structure, and two phases with approximate stoichiometries Bi₁₇Fe₂Nb₃₁O₁₀₆ and Bi₁₇Fe₃Nb₃₀O₁₀₅ that appear to be structurally related to Bi₈Nb₁₈O₅₇. The fourth ternary phase found in this system is pyrochlore (A₂B₂O₆O′), which forms an extensive solid solution region at Bi-deficient stoichiometries (relative to Bi₂FeNbO₇) suggesting that ≈4-15% of the A-sites are occupied by Fe³⁺. X-ray powder diffraction data confirmed that all Bi-Fe-Nb-O pyrochlores form with positional displacements, as found for analogous pyrochlores with Zn, Mn, or Co instead of Fe. A structural refinement of the pyrochlore 0.4400:0.2700:0.2900 Bi₂O₃:Fe₂O₃:Nb₂O₅ using neutron powder diffraction data is reported with the A cations displaced (0.43 Å) to 96g sites and O′ displaced (0.29 Å) to 32e sites (Bi_1.721Fe_0.190(Fe_0.866Nb_1.134)O₇, Fd3¯m (#227), ). This displacive model is somewhat different from that reported for Bi_1.5Zn_0.92Nb_1.5O_6.92, which exhibits twice the concentration of small B-type cations on the A-sites as the Fe system. Bi-Fe-Nb-O pyrochlores exhibited overall paramagnetic behavior with large negative Curie-Weiss temperature intercepts, slight superparamagnetic effects, and depressed observed moments compared to high-spin, spin-only values. The single-phase pyrochlore with composition Bi_1.657Fe_1.092Nb_1.150O₇ exhibited low-temperature dielectric relaxation similar to that observed for Bi_1.5Zn_0.92Nb_1.5O_6.92; at 1 MHz and 200 K the relative permittivity was 125, and above 350 K conductive effects were observed.     

SnO_2改性TiO_2对V_2O_5-WO_3/TiO_2催化剂结构和SCR性能影响

采用共沉淀法将SnO_2组分掺入到V_2O_5-WO_3/TiO_2催化剂载体TiO_2中,并通过多种物理化学手段,考察了不同SnO_2掺入量时对催化剂结构,表面分散物种和SCR性能影响.结果表明,SnO_2掺入到TiO_2中,元素Sn与Ti以Sn—O—Ti键形式相互作用,促进锐钛矿型TiO_2向金红石型TiO_2转变.在特定条件下,VO_x与WO_x物种和SnTi氧化物之间以V—O—Ti(Sn)和W—O—Ti(Sn)键形式相互作用,提高了VO_x物种可还原能力、促进了具有更多B酸酸量四面体WOx物种和V~(5+)物种生成.VW/SnTi催化剂表面VO_x物种与WO_x物种之间的相互作用更强.因此,VW/SnTi催化剂具有更好的SCR活性.     

Selective hydrothermal synthesis of BiOBr microflowers and Bi2O3 shuttles with concave surfaces

Through controlling the amount of NaOH added, BiOBr and Bi₂O₃ with different shapes were hydrothermally synthesized in the reaction system of Bi(NO₃)₃-hexadecyl trimethyl ammonium bromide (CTAB)-NaOH. As 8 mmol of NaOH was added, BiOBr microflowers constructed of nanoflakes were synthesized. The thickness of these single-crystal nanoflakes was about 20 nm. In the similar condition, when the amount of NaOH added was 28 mmol, Bi₂O₃ shuttles with concave surfaces were obtained. The length of these shuttles was 100 μm and the diameter at the middle of these shuttles was 50 μm. The photocatalytic activity of as-prepared BiOBr microflowers was evaluated by the degradation of methyl orange (MO) under visible-light irradiation (λ>420 nm), which was up to 96% within 90 min.     

Bi2O3掺杂对Ag(Nb0.8Ta0.2)O3陶瓷结构和介电性能的影响

本文研究了Bi₂O₃掺杂对Ag(Nb_0.8Ta_0.2)O₃陶瓷的结构和介电性能的影响。X射线衍射(XRD)结果表明,Bi₂O₃的掺杂可以使陶瓷中Ag⁺被还原并析出,且银析出的量随Bi₂O₃掺杂量的增加而不断增加,这可能源自于Bi³⁺对Ag⁺的取代。在一定范围内增大Bi₂O₃掺杂量可提高Ag(Nb_0.8Ta_0.2)O₃陶瓷的室温介电常数,降低介电损耗,并使温度系数向负值方向移动。当Bi₂O₃的掺杂量约为3.5wt%时,样品具有较大的介电常数(ε=672)和较小的介电损耗(tanδ=7.3×10^-4)。     

Bi_2O_3掺杂对Ag(Nb_(0.8)Ta_(0.2))O_3陶瓷结构和介电性能的影响(英文)

本文研究了Bi2O3掺杂对Ag(Nb0.8Ta0.2)O3陶瓷的结构和介电性能的影响。X射线衍射(XRD)结果表明,Bi2O3的掺杂可以使陶瓷中Ag+被还原并析出,且银析出的量随Bi2O3掺杂量的增加而不断增加,这可能源自于Bi3+对Ag+的取代。在一定范围内增大Bi2O3掺杂量可提高Ag(Nb0.8Ta0.2)O3陶瓷的室温介电常数,降低介电损耗,并使温度系数向负值方向移动。当Bi2O3的掺杂量约为3.5wt%时,样品具有较大的介电常数(ε=672)和较小的介电损耗(tanδ=7.3×10-4)。     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

LiMn_2O_4/TiO_2催化剂上甲烷氧化偶联反应性能的研究

采用固相反应法制备了具有尖晶石结构的LiMn_2O_4/TiO_2系列催化剂,探讨了TiO_2、Li/TiO_2、Mn/TiO_2、LiMn_2O_4及LiMn_2O_4/TiO_2等不同组成催化剂的甲烷氧化偶联反应性能,采用XRD、XPS、CO_2-TPD和H_2-TPR等表征方法对该系列催化剂进行了分析。结果表明,具有尖晶石结构的LiMn_2O_4化合物具有较高的甲烷氧化偶联催化活性,在775℃、0.1MPa、7200mL/(h·g),CH_4∶O_2(体积比)为2.5的条件下,甲烷转化率可达25.8%,C2选择性可达43.2%。TiO_2的存在不仅进一步提高了甲烷转化率和C2选择性,还有效抑制了甲烷完全氧化形成CO_2的过程。负载8%LiMn_2O_4的LiMn_2O_4/TiO_2催化剂性能达到最优,此时甲烷转化率达到31.6%,C2选择性为52.4%,CO_2选择性降低到26.3%。考察了不同焙烧温度对催化剂活性的影响,850℃为LiMn_2O_4/TiO_2催化剂的最佳焙烧温度。     

Acidic properties of V2O5-WO3/ZrO2 catalysts

The adsorption of pyridine on V₂O₅−WO₃/ZrO₂ has been studied by FTIR. In V₂O₅/ZrO₂ (2 wt.%), the number of both Br?nsted and Lewis acidic sites increased with the addition of WO₃, while in V₂O₅/ZrO₂ (5 wt.%), Br?nsted sites increased and Lewis sites did not change.     

三维有序大孔复合材料Bi2O3/TiO2制备与多模式下光催化降解结晶紫

以TiO2为基体,在聚苯乙烯(PS)胶球和EO20PO70EO20(P123)两种模板剂作用下通过溶胶-凝胶及煅烧后处理方法制备了三维有序大孔纳米复合材料Bi2O3/TiO2.经傅里叶变换红外(FT-IR)光谱、X-射线衍射(XRD)、等离子体原子发射光谱(ICP-AES)、紫外-可见漫反射吸收光谱(UV-Vis DRS)、X-射线光电子能谱(XPS)、扫描电子显微镜(SEM)和N2吸附-脱附等物理测试手段对其组成、结构、形貌及表面物理化学性能进行了表征.结果表明,该复合材料晶型结构良好,孔结构排列整齐有序,孔壁呈介孔结构,属于三维有序大孔材料(3DOM).与TiO2相比,3DOM-Bi2O3/TiO2对光的吸收至少红移60 nm,且红移至可见区.在紫外光、可见光以及微波辅助等多模式光催化降解结晶紫的实验中,复合材料3DOM-Bi2O3/TiO2表现出良好的光催化活性,其活性明显高于P25、Bi2O3和Bi2O3/TiO2.同时,该复合材料针对不同类型的染料均表现出较好的紫外光降解效果,且3次循环实验后,依旧保持较高活性.     

Bi2O3-catalyzed oxidation of aldehydes with t-BuOOH

A variety of aromatic, aliphatic and conjugated aldehydes were transformed to the corresponding carboxylic acids with 70% t-BuOOH solution (water) in the presence of catalytic amounts of Bi₂O₃. This method possesses a wide range of capabilities, does not involve cumbersome work-up, exhibits chemoselectivity and proceeds under mild conditions. The resulting products are obtained in good yields within reasonable time. The overall method is green.     

PO43-掺杂Bi2O2CO3/Bi0的制备及其可见光催化性能

构建氧空位以及附着金属单质Bi(Bi⁰)是增强半导体材料光吸收性能、促进半导体光生载流子分离的有效方法。通过简单的共沉淀法及氢气热还原成功制备了PO₄^3-掺杂Bi₂O₂CO₃附着Bi⁰(Bi-P-BOC)的可见光催化剂,并对其在可见光下催化降解氧氟沙星(OFX)的性能及机理进行了研究。材料表征结果表明BOC随着PO₄^3-的均匀掺杂,可见光吸收能力增强,表面缺陷增多,比表面积增大。而随着氢气热还原,BOC表面形成Bi⁰的同时也原位构建了大量的氧空位。可见光催化性能测试表明,Bi-P-BOC可以在180 min内降解约85%的OFX,降解速率为0.013 0 min^-1,是BOC降解速率的8倍。Bi-P-BOC光催化降解机理表明其具有更好的可见光吸收能力,Bi⁰以及氧空位的存在促进了光生载流子的分离,h⁺是其...     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

Following the crystallisation of Bi2Mo2O9 catalyst by combined XRD/QuEXAFS

The formation ofβ-phase Bi₂Mo₂O₉ catalyst from a precursor precipitate has been studied using thein situ combined XRD/QuEXAFS technique and DSC during calcination. Accordingly the precursor was observed to undergo a number of changes in both the molybdenum (VI) coordination and long-range ordering during this heating. Initially the two other forms of bismuth molybdate (α-andγ-phases) were observed to form from the poorly crystalline precursor at about 230°C, however, theβ-phase eventually crystallised after prolonged heating at 560°C. Dedicated to Professor C N R Rao on his 70th birthday     

PO43-掺杂Bi2O2CO3/Bi0的制备及其可见光催化性能

构建氧空位以及附着金属单质Bi(Bi⁰)是增强半导体材料光吸收性能、促进半导体光生载流子分离的有效方法。通过简单的共沉淀法及氢气热还原成功制备了PO₄^3-掺杂Bi₂O₂CO₃附着Bi⁰(Bi-P-BOC)的可见光催化剂,并对其在可见光下催化降解氧氟沙星(OFX)的性能及机理进行了研究。材料表征结果表明BOC随着PO₄^3-的均匀掺杂,可见光吸收能力增强,表面缺陷增多,比表面积增大。而随着氢气热还原,BOC表面形成 Bi⁰的同时也原位构建了大量的氧空位。可见光催化性能测试表明,Bi-P-BOC可以在180 min内降解约85%的OFX,降解速率为0.013 0 min^-1,是BOC降解速率的8倍。Bi-P-BOC光催化降解机理表明其具有更好的可见光吸收能力,Bi⁰以及氧空位的存在促进了光生载流子的分离,h+是其光催化降解过程中的主要的活性氧物种(ROS),此外,¹O₂和·O₂^-也对降解有一定贡献。