One-pot synthesis,characterization and properties of acid-catalyzed resorcinol/formaldehyde cross-linked silica aerogels and their conversion to hierarchical porous carbon monoliths

A rapid and facile synthesis of resorcinol/formaldehyde cross-linked silica (RF/SiO₂) aerogels was carried out in one pot based on an acid-catalyzed route, instead of the previously reported base-catalyzed ones. The gelation time was reduced to several hours at room temperature while it took several days even under heating conditions in the base-catalyzed ones. The interpenetrating network of RF/SiO₂ aerogels showed similar porous structures with those of silica aerogels or RF aerogels. Their thermal conductivity was as low as that of the typical glass wool materials. The mechanical properties are characterized by dynamic mechanical analysis and compression testing. At room temperature, the results of compression testing show that the compressive Young’s modulus or ultimate failure strength of RF/SiO₂ aerogel specimen is higher than that of native SiO₂ aerogels with a similar density. The one-pot method improves the efficiency and reduces the cost of RF/SiO₂ aerogels. The hierarchical porous carbon monoliths are also converted from carbonized RF/SiO₂ aerogels by an additional HF treatment. Hence, they could be further explored as multifunctional candidate materials for thermal, mechanical, and electrochemical applications.     

Influence of supercritical drying fluids on structures and properties of low-density Cu-doped SiO2 composite aerogels

The Cu-doped SiO₂ composite aerogels were successfully prepared by sol–gel process and subsequently supercritical drying with ethanol and CO₂. The Cu-doped SiO₂ composite aerogels had porous texture, low density (<100 mg cm^?3) and high specific surface area (>800 m² g^?1), which were investigated by FESEM and nitrogen adsorption desorption porosimetry. The FTIR spectra of the aerogels showed that the ethanol-dried aerogels had been modified by ethyl while the corresponding CO₂-dried aerogels had more Si–OH groups. The phase structure and thermal stability were investigated by XRD and TGA, respectively. Due to the reducibility of ethanol, the copper was crystalline in ethanol-dried sample. The Cu-doped SiO₂ composite aerogels dried with supercritical ethanol had larger pore diameter and better thermal stability under 400 °C in comparison with CO₂-dried composite aerogels. The structures and properties of Cu-doped SiO₂ composite aerogels are obviously affected by supercritical drying conditions. The effect research could instruct the synthesis of different state of Cu in composite aerogels.     

Ambient pressure dried tetrapropoxysilane-based silica aerogels with high specific surface area

In the present paper, we report the synthesis of tetrapropoxysilane (TPOS)-based silica aerogels with high surface area and large pore volume. The silica aerogels were prepared by a two-step sol-gel process followed by surface modification via a simple ambient pressure drying approach. In order to minimize drying shrinkage and obtain hydrophobic aerogels, the surface of the alcogels was modified using trichloromethylsilane as a silylating agent. The effect of the sol-gel compositional parameters on the polymerization of aerogels prepared by TPOS, one of the precursors belonging to the Si(OR)₄ family, was reported for the first time. The oxalic acid and NH₄OH concentrations were adjusted to achieve good-quality aerogels with high surface area, low density, and high transparency. Controlling the hydrolysis and condensation reactions of the TPOS precursor turned out to be the most important factor to determine the pore characteristics of the aerogel. Highly transparent aerogels with high specific surface area (938 m²/g) and low density (0.047 g/cm³) could be obtained using an optimized TPOS/MeOH molar ratio with appropriate concentrations of oxalic acid and NH₄OH.     

Fabrication of Cobaltosic Oxide Nanoparticle-Doped 3 D MXene/Graphene Hybrid Porous Aerogels for All-Solid-State Supercapacitors

MXenes are a new family of 2 D transition metal carbides and nitrides, which have attracted enormous attention in electrochemical energy storage, sensing technology, and catalysis owing to their good conductivity, high specific surface area, and excellent electrochemical properties. In this work, a series of Co₃O₄-doped 3 D MXene/RGO hybrid porous aerogels is designed and prepared through a facile in situ reduction and thermal annealing process, in which the reduced graphene oxide (RGO) conductive network can electrically link the separated Co₃O₄-MXene composite nanosheets, leading to enhanced electronic conductivity. It is found that upon using the Co₃O₄-MXene/RGO hybrid porous aerogel prepared with a mass ratio of Co₃O₄-MXene/RGO of 3:1 (CMR31) as an electrode for a supercapacitor, a superior specific capacitance of 345 F g⁻¹ at the current density of 1 A g⁻¹ is achieved, which is significantly higher than those of Ti₃C₂T_x MXene, RGO, and MXene/RGO electrodes. In addition, a high capacitance retention (85 % of the initial capacitance after 10 000 cycles at a high current density of 3 A g⁻¹) and a low internal resistance R_s (0.44 Ω) can be achieved. An all-solid-state asymmetric supercapacitor (ASC) device is assembled using CMR31, and it has the ability to light up a blue LED indicator for 5 min if four ASCs are connected in series. Therefore, these novel Co₃O₄-MXene/RGO hybrid porous aerogels have potential practical applications in high-energy storage devices.     

Assembly of BaTiO3 Nanocrystals into Macroscopic Aerogel Monoliths with High Surface Area

Aerogels with their low density and high surface area are fascinating materials. However, their advantageous morphology is still far from being fully exploited owing to their limited compositional variety and low crystallinity. Replacing the sol–gel process by a particle‐based assembly route is a powerful alternative to expand the accessible functionalities of aerogels. A strategy is presented for the controlled destabilization of concentrated dispersions of BaTiO₃ nanoparticles, resulting in the assembly of the fully crystalline building blocks into cylindrically shaped monolithic gels, thereby combining the inherent properties of ternary oxides with the highly porous microstructure of aerogels. The obtained aerogels showed an unprecedentedly high surface area of over 300 m² g^?1.     

Boosting CO2 Electroreduction on N,P-Co-doped Carbon Aerogels

Electroreduction of CO₂ to CO powered by renewable electricity is a possible alternative to synthesizing CO from fossil fuel. However, it is very hard to achieve high current density at high faradaic efficiency (FE). Here, the first use of N,P-co-doped carbon aerogels (NPCA) to boost CO₂ reduction to CO is presented. The FE of CO could reach 99.1 % with a partial current density of −143.6 mA cm⁻², which is one of the highest current densities to date. NPCA has higher electrochemical active area and overall electronic conductivity than that of N- or P-doped carbon aerogels, which favors electron transfer from CO₂ to its radical anion or other key intermediates. By control experiments and theoretical calculations, it is found that the pyridinic N was very active for CO₂ reduction to CO, and co-doping of P with N hinder the hydrogen evolution reaction (HER) significantly, and thus the both current density and FE are very high.     

Boosting CO2 Electroreduction on N,P‐Co‐doped Carbon Aerogels

Electroreduction of CO₂ to CO powered by renewable electricity is a possible alternative to synthesizing CO from fossil fuel. However, it is very hard to achieve high current density at high faradaic efficiency (FE). Here, the first use of N,P‐co‐doped carbon aerogels (NPCA) to boost CO₂ reduction to CO is presented. The FE of CO could reach 99.1 % with a partial current density of ?143.6 mA cm^?2, which is one of the highest current densities to date. NPCA has higher electrochemical active area and overall electronic conductivity than that of N‐ or P‐doped carbon aerogels, which favors electron transfer from CO₂ to its radical anion or other key intermediates. By control experiments and theoretical calculations, it is found that the pyridinic N was very active for CO₂ reduction to CO, and co‐doping of P with N hinder the hydrogen evolution reaction (HER) significantly, and thus the both current density and FE are very high.     

Optically transparent silica aerogels based on sodium silicate by a two step sol–gel process and ambient pressure drying

Interest in improving the optical transmission of sodium silicate-based aerogels by ambient pressure drying led to the synthesis of aerogels using a two-step sol–gel process. To produce optically transparent silica aerogel granules, NH₄F (1 M) and HCl (4 M) were used as hydrolyzing and condensation catalysts, respectively. The silica aerogels were characterized by their bulk density, porosity (%), contact angle and thermal conductivity. Optical transmission of as synthesized aerogels was studied by comparing the photos of aerogel granules. Scanning electron microscopic study showed the presence of fractal structures in these aerogels. The degree of transparency in two step sol–gel process-based aerogels is higher than the conventional single step aerogels. The N₂ adsorption–desorption analysis depicts that the two step sol–gel based aerogels have large surface areas. Optically transparent silica aerogels with a low density of ∼0.125 g/cc, low thermal conductivity of ∼0.128 W/mK and higher Brunauer, Emmett, and Teller surface area of ∼425 m²/g were obtained by using NH₄F (1 M), HCl (4 M), and a molar ratio of Na₂SiO₃::H₂O::trimethylchlorosilane of 1::146.67::9.46. The aerogels retained their hydrophobicity up to 500 °C.     

The Importance of Precursors and Modification Groups of Aerogels in CO2 Capture

The rapid growth of CO₂ emissions in the atmosphere has attracted great attention due to the influence of the greenhouse effect. Aerogels’ application for capturing CO₂ is quite promising owing to their numerous advantages, such as high porosity (~95%); these are predominantly mesoporous (20–50 nm) materials with very high surface area (>800 m²∙g⁻¹). To increase the CO₂ level of aerogels’ uptake capacity and selectivity, active materials have been investigated, such as potassium carbonate, K₂CO₃, amines, and ionic-liquid amino-acid moieties loaded onto the surface of aerogels. The flexibility of the composition and surface chemistry of aerogels can be modified intentionally—indeed, manipulated—for CO₂ capture. Up to now, most research has focused mainly on the synthesis of amine-modified silica aerogels and the evaluation of their CO₂-sorption properties. However, there is no comprehensive study focusing on the effect of different types of aerogels and modification groups on the adsorption of CO₂. In this review, we present, in broad terms, the use of different precursors, as well as modification of synthesis parameters. The present review aims to consider which kind of precursors and modification groups can serve as potentially attractive molecular-design characteristics in promising materials for capturing CO₂.     

Hierarchical Mn3O4 Anchored on 3D Graphene Aerogels via C−O−Mn Linkage with Superior Electrochemical Performance for Flexible Asymmetric Supercapacitor

Flexible asymmetric supercapacitors are more appealing in flexible electronics because of high power density, wide cell voltage, and higher energy density than symmetric supercapacitors in aqueous electrolyte. In virtues of excellent conductivity, rich porous structure and interconnected honeycomb structure, three dimensional graphene aerogels show great potential as electrode in asymmetric supercapacitors. However, graphene aerogels are rarely used in flexible asymmetric supercapacitors because of easily re-stacking of graphene sheets, resulting in low electrochemical activity. Herein, flower-like hierarchical Mn₃O₄ and carbon nanohorns are incorporated into three dimensional graphene aerogels to restrain the stack of graphene sheets, and are applied as the positive and negative electrode for asymmetric supercapacitors devices, respectively. Besides, a strong chemical coupling between Mn₃O₄ and graphene via the C-O-Mn linkage is constructed and can provide a good electron-transport pathway during cycles. Consequently, the asymmetric supercapacitor device shows high rate cycle stability (87.8 % after 5000 cycles) and achieves a high energy density of 17.4 μWh cm⁻² with power density of 14.1 mW cm⁻² (156.7 mW cm⁻³) at 1.4 V.     

Effect of iron acetylacetonate on physico-chemical properties of waterglass based aerogels by ambient pressure drying

The effect of iron acetylacetonate on the physico-chemical properties of waterglass based silica aerogels by ambient pressure drying has been investigated. Doping the gels with iron acetylacetonat (FeAA) facilitates in the diminution of the density of the aerogels. The well established silica network provides effective confinement of FeAA nanoparticles which resists the collapse of silica network during ambient pressure drying. Therefore, in the present paper, the effects of FeAA on the physico-chemical properties of the aerogels have been studied by varying the FeAA:Na₂SiO₃ molar ratio from 3 × 10⁻⁴ to 6 × 10⁻⁴. The aerogels were prepared via ambient pressure drying and characterized by the bulk density, thermal conductivity and water contact angle. The aerogel’s surface morphology, elemental analysis and pore structure were characterized by means of EDAX and FTIR, TEM and N₂ adsorption- desorption analyzer. The high temperature hydrophobicity of these aerogels was checked by heating them in temperature controlled furnace. Silica aerogels with low density ~0.050 g/cc have been obtained using the molar ratio of Na₂SiO₃:H₂O:FeAA:Citric acid:TMCS at 1:146.67:3 × 10⁻⁴:0.54:9.46, respectively. EDAX and FTIR studies show that the iron species are entrapped in the mesoporous framework and not took part in the bonding with silica.     

Physico-chemical properties of ambiently dried sodium silicate based aerogels catalyzed with various acids

Experimental results on the physico-chemical properties of ambiently dried sodium silicate based aerogels catalyzed with various acids are reported. The aerogels were prepared by hydrolysis and polycondensation of sodium silicate followed by subsequent washings, surface chemical modification and ambient pressure drying using 10 various acid catalysts consisting of strong and weak acids. The strength and concentration of acids have the major effect on the gelation of sol and hence the physico-chemical properties of the silica aerogels. Strong acids such as HCl, HNO₃ and H₂SO₄ resulted in shrunk (70–95%) aerogels whereas weak acids such as citric and tartaric acids resulted in less shrunk (34–50%) aerogels. The physical properties of silica aerogels were studied by measuring bulk density, volume shrinkage (%), porosity (%), pore volume, thermal conductivity, contact angle with water, Transmission Electron Microscopy (TEM), Atomic Absorption Spectroscopy (AAS), Fourier Transform Infrared Spectroscopy (FTIR), Thermo Gravimetric-Differential Thermal (TG-DT) analyses and N₂ adsorption–desorption BET surface analyzer. The best quality silica aerogels in terms of low density (0.086 g/cm³), low volume shrinkage (34%), high porosity (95%), low thermal conductivity (0.09 W/m K) and hydrophobic (148°) were obtained for molar ratio of Na₂SiO₃:H₂O:citric acid:TMCS at 1:146.67:0.72:9.46 with 20 min gelation time. The resulting aerogels exhibited the thermal stability up to around 420 °C.     

Effect of Precursor Nature and Sol-Gel Synthesis Conditions on TiO2 Aerogel’s Structure

The aim of this investigation was to synthesize high porosity TiO₂ aerogel by applying sol-gel and subcritical drying methods and to identify the influence of reagent’s nature and synthesis conditions on their structural and optical properties. Methods of XRD, FT-IR, BET, STA, SEM, and UV-vis were applied to investigate and compare the properties of synthesized TiO₂ aerogels and to determine the most effective synthesis route. The structural parameters of the synthesized materials can be varied by changing the precursor type (titanium (IV), isopropoxide (TIP), or tetrabutylorthotitanate (TBOT)) and the nature of the solvent used for additional exchange (n-hexane (nH), cyclohexane (CH), or diethyl ether (DE)). All of the subcritical dried samples show the amorphous structure, which tends to crystallize into the anatase phase after calcination. The number of micro and mesopores and the specific surface area depends on the synthesis conditions. The pores with the highest diameter have been found for additionally nH exchanged and aged aerogel synthesized from precursor TIP. Despite the imperfections in the structure, the produced aerogels show structural and optical properties typical of the TiO₂ structures mentioned in the literature.     

Synthesis and physical properties of TEOS-based silica aerogels prepared by two step (acid–base) sol–gel process

The experimental results on the synthesis and physical properties of tetraethoxysilane- (TEOS) based silica aerogels produced by two step (acid–base) sol–gel process, are reported. The oxalic acid (A) and NH₄OH (B) concentrations were varied from 0 to 0.1 M and from 0.4 to 3 M, respectively. Monolithic and transparent aerogels have been obtained for the values of A=0.001 M and B=1 M. The effect of time interval (t) before the base catalyst (NH₄OH) addition to the acidic sol was studied from 0 to 72 h. The time interval at t=24 h of NH₄OH addition was found to be the best, in terms of low volume shrinkage, high optical transmission and monolithicity. The molar ratio of EtOH/TEOS (S) was varied from 3 to 7.5. Monolithic and transparent aerogels were obtained for an S value of 6.9. Also, the effects of molar ratio of acidic water, i.e., H₂O/TEOS (W₁) and basic water, i.e., H₂O/TEOS (W₂) on the physical properties of the aerogels have been studied. Highly transparent (∼90%) and monolithic aerogels with lower volume shrinkage (<10%) were obtained for the molar ratio 1:6.9:3.5:2.2 of TEOS:EtOH:acidic (H₂O):basic (H₂O). The results are discussed by taking into consideration the hydrolysis and polycondensation reactions. The aerogels were characterized by scanning electron microscopy (SEM), optical transmission, bulk density, volume shrinkage and porosity measurements.     

Heat-Treated Aerogel as a Catalyst for the Oxygen Reduction Reaction

Aerogels are fascinating materials that can be used for a wide range of applications, one of which is electrocatalysis of the important oxygen reduction reaction. In their inorganic form, aerogels can have ultrahigh catalytic site density, high surface area, and tunable physical properties and chemical structures—important features in heterogeneous catalysis. Herein, we report on the synthesis and electrocatalytic properties of an iron–porphyrin aerogel. 5,10,15,20-(Tetra-4-aminophenyl)porphyrin (H₂TAPP) and Fe^II were used as building blocks of the aerogel, which was later heat-treated at 600 °C to enhance electronic conductivity and catalytic activity, while preserving its macrostructure. The resulting material has a very high concentration of atomically dispersed catalytic sites (9.7×10²⁰ sites g⁻¹) capable of catalyzing the oxygen reduction reaction in alkaline solution (E_onset=0.92 V vs. RHE, TOF=0.25 e⁻ site⁻¹ s⁻¹ at 0.80 V vs. RHE).     

Heat‐Treated Aerogel as a Catalyst for the Oxygen Reduction Reaction

Aerogels are fascinating materials that can be used for a wide range of applications, one of which is electrocatalysis of the important oxygen reduction reaction. In their inorganic form, aerogels can have ultrahigh catalytic site density, high surface area, and tunable physical properties and chemical structures—important features in heterogeneous catalysis. Herein, we report on the synthesis and electrocatalytic properties of an iron–porphyrin aerogel. 5,10,15,20‐(Tetra‐4‐aminophenyl)porphyrin (H₂TAPP) and Fe^II were used as building blocks of the aerogel, which was later heat‐treated at 600 °C to enhance electronic conductivity and catalytic activity, while preserving its macrostructure. The resulting material has a very high concentration of atomically dispersed catalytic sites (9.7×10²⁰ sites g^?1) capable of catalyzing the oxygen reduction reaction in alkaline solution (E_onset=0.92 V vs. RHE, TOF=0.25 e^? site^?1 s^?1 at 0.80 V vs. RHE).     

Effect of the Synthesis Method on the Functional Properties of Lithium-Rich Complex Oxides Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript>

Layered Li-rich transition metal oxides are considered among the most promising cathode materials for high energy density lithium-ion batteries. It was studied how the method and conditions of synthesis of Li-rich oxides Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ affect their electrochemical properties. Coprecipitation methods and modified Pechini process were used. It was shown that it is necessary to carefully choose the synthesis conditions when using the modified Pechini method because of their significant effect on the morphology of Li-rich oxides. Samples were obtained with high electrochemical characteristics: capacity discharge of 260–270 mAh/g (16 mA/g) and 60–70 mAh/g (988 mA/g) within the voltage range of 2.5–4.8 V.     

Hydrogel-Derived Honeycomb Ni3S4/N,P-C as an Efficient Oxygen Evolution Catalyst

The development of high-efficiency electrocatalysts with low costs for the oxygen evolution reaction (OER) is essential, but remains challenging. Herein, a new synthetic process is proposed to prepare Ni₃S₄ particles embedded in N,P-codoped honeycomb porous carbon aerogels (Ni₃S₄/N,P-HPC) through a hydrogel approach. The preparation of Ni₃S₄/N,P-HPC begins with the sol–gel polymerization of tripolyphosphate, chitosan, and guanidine polymer that contains metal-binding sites, allowing for the uniform incorporation of Ni ions into the gel matrix, freeze-drying, and subsequent carbonization under an inert atmosphere. This synthesis resolves difficulties in synthesizing the pure Ni₃S₄ phase caused by the instability of Ni₃S₄ at high temperature, while affording good control of the porous structure and N,P-doping of carbon aerogels. The synergy between the structural advantages of N,P-carbon aerogels (such as easily accessible active sites, high specific surface area, and excellent electron transport) and the intrinsic electrochemical properties of Ni₃S₄ result in the outstanding OER performance of Ni₃S₄/N,P-HPC, with overpotentials as low as 0.37 V at 10 mA cm⁻². The work outlined herein offers a simple and effective method for the development of carbon-based electrocatalysts for renewable energy conversion.     

Electrochemistry of Electrode Materials Containing S−Se Bonds for Rechargeable Batteries

Sulfur (S) and selenium (Se) have been considered as promising high capacity cathode materials for rechargeable batteries. They have differences in their physical properties (e.g., electronic conductivity) but the same number of electrons in their outermost shells, which leads to similarity in their electrochemical behavior in batteries. In recent years, some efforts have been taken to combine them in electrodes in the hope of improved battery performance. The S−Se bonds of these electrode materials lead to unusual properties and intriguing electrochemical behavior, which have attracted increasing interest. In this Minireview, electrode materials containing S−Se bonds are summarized, including inorganic S_xSe_y solid solutions, organic compounds, and organic–inorganic hybrid materials. Our understanding in these materials is still premature, but they have shown unique properties to be electrode materials. We hope this Minireview could provide a new insight into the design, synthesis, and understanding of these materials, which could enable high energy density rechargeable batteries.     

Graphene oxide-gelatin aerogels as wound dressings with improved hemostatic properties

Graphene oxide (GO)-gelatin (G) aerogels were synthesized via the physical interactions between GO-oxygenated groups and G amine groups to obtain potential hemostatic devices. The influence of the aerogel synthesis conditions—acid and basic GO suspensions—was used to evaluate their clotting performance. These materials were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction, Raman spectroscopy, and thermogravimetric analysis, and their properties of absorption, stiffness, porosity, surface charge, and pore size were measured and compared. The clotting activity of the materials was evaluated by prothrombin time, activated partial thromboplastin time, soluble human P-selectin, and in vitro dynamic clotting assays, as well as their cytotoxicity. GO-G aerogels presented heterogeneous microporous structures with porosities higher than 90% and a high PBS absorption capacity, 49.6 ± 3.8 g_PBS/g_aerogel for positively charged aerogels (15.63 ± 0.5 mV) and 42.75 ± 2.38 g_PBS/g_aerogel for negatively charged aerogels (?20.53 ± 1.07 mV). Comparatively, positively charged aerogels had superior structural properties to negatively charged aerogels, such as stiffness, porosities, and pore sizes, because they promote H bonding. In regard to hemostatic activity, negatively charged aerogels had higher clotting performance, reaching 95.6% clotted blood, and therefore provide a suitable structure for the coagulation process and promote clot formation without using common mechanisms. In addition, negatively charged aerogels were not cytotoxic and promoted fibroblast proliferation. Therefore, negatively charged GO-G aerogels may be a potential hemostatic device that can be used as a wound dressing.