蓖麻油聚氨酯和乙烯类聚合物互穿网络材料的生成特点及其动态力学性能

研究蓖麻油聚氨酯/取代乙烯共聚物的互穿网络物(IPN)的生成特点指出,其中取代乙烯游离基共聚的氧化还原引发剂组份-过氧化苯甲酰或二甲基苯胺都能加速聚氨酯网络(Pu)的生成。反应温度在 30℃以上蓖麻油也能参与游离基共聚。蓖麻油不仅与TDI反应生成Pu网络,而且也有小部分参与取代乙烯共聚物长枝链的形成。Pu网络的形成较长枝链的生成为快。生成Pu网络时所放出的热促进取代乙烯与少量蓖麻油的双键共聚,最后生成的IPN不溶于甲苯。这表明生成的是接技的半IPN,而不是单纯的半IPN。动态力学研究指出,包含聚苯乙烯或聚甲基丙烯酸甲酯的这种IPN呈现二个T_g,而只包含聚丙烯腈的仅一个T_g,说明后一IPN中相容性较好,有较多的分子混合。随着聚氨酯与聚取代乙烯的比例减少,二个T_g间的差距减少,而较高温度的T_g随取代乙烯共聚物中丙烯腈含量增加而变小。     

离子-电子导电中呈现协同效应的互穿网络聚合物

用2,4-甲苯二异氰酸酯将蓖麻油及聚乙二醇(PEG)偶联成聚氨酯,同时通过自由基聚合使2-乙烯基吡啶(VP)与蓖麻油的双键共聚,生成互穿网络聚合物(IPN),其产率及凝胶含量大多超过93%,力学性能很好.当IPN与LiClO₄络合后呈现离子导电现象;与TCNE或TCNQ络合后产生电子导电,与LiClO₄及TCNE(TCNQ)络合后,呈现比上述两种导电率更大且具有协同效应的混合导电率,在25℃混合电导率可达到10^-3～10^-2S/cm.     

网间交联型增韧环氧树脂/蓖麻油聚氨酯互穿网络聚合物的动态力学性能和形态结构

以增韧环氧树脂(TEP)和蓖麻油聚氨酯[PU(CO)]形成的互穿网络聚合物(IPN),两网络间具有一定数量的交联点,在一定组成下,该IPN的tanδ-T曲线半峰宽达100℃,tanδ最大值接近1,阻尼性能良好。形态研究表明,该IPN既有增韧环氧树脂本身的两相结构,又有IPN的两相结构。     

网间交联型增韧环氧树脂/蓖麻油聚氨酯互穿网络聚合物的动态力学性能和形态结构

 以增韧环氧树脂(TEP)和蓖麻油聚氨酯[PU(CO)]形成的互穿网络聚合物(IPN),两网络间具有一定数量的交联点,在一定组成下,该IPN的tanδ-T曲线半峰宽达100℃,tanδ最大值接近1,阻尼性能良好。形态研究表明,该IPN既有增韧环氧树脂本身的两相结构,又有IPN的两相结构。     

瓜胶/聚丙烯酸互穿聚合物网络水凝胶对模型药物的负载与控制释放

考察了以牛乳清蛋白(BSA)为模型药物,通过相平衡分配法制备载药瓜胶(GG)/聚丙烯酸(PAA)互穿聚合物网络(IPN)水凝胶的工艺条件.借助紫外可见光谱仪研究了载药水凝胶在结肠酶存在下的控制释放行为.结果表明:载药容量(CM)随瓜胶、丙烯酸用量的增加而下降,半IPN水凝胶的Cm较全IPN的略大;结肠酶能明显提高半IPN与全IPN中的BSA释放速率,且提高幅度随GG含量的增加而加快,GG/PAA IPN水凝胶具有结肠定位降解的特性,有望成为靶向结肠给药的理想载体材料.     

疏水/亲水大孔聚二乙烯基苯/聚(N-2-氨基乙基丙烯酰胺)IPN树脂的合成及对水杨酸吸附性能研究

采用分步悬浮聚合法制备了聚二乙烯基苯/聚丙烯酸甲酯(PDVB/PMA)大孔互穿聚合物网络,将其中的聚丙烯酸甲酯用乙二胺氨解,合成了具有疏水/亲水性能的聚二乙烯基苯/聚(N-2-氨基乙基丙烯酰胺)(PDVB/PNAEAM)大孔互穿聚合物网络(IPN);测定了该树脂的孔结构、含水量、弱碱交换量和溶胀性能;测定了该树脂对水杨酸在不同温度下的吸附等温线,利用热力学函数关系计算出了吸附焓、自由能和熵.推测PDVB/PNAEAM IPN树脂中疏水性的PDVB一网具有疏水作用吸附能力、亲水性的PNAEAM一网具有氢键作用吸附能力.动态吸附及脱附实验表明湿态PDVB/PNAEAM IPN树脂对水溶液中水杨酸的饱和吸附量达到46.1mg/mL.树脂可以通过4%NaOH溶液再生.PDVB/PNAEAM IPN树脂在分离工业废水中水杨酸等芳香有机酸有良好的应用前景.     

聚氨酯／聚甲基丙烯酸甲酯互穿聚合物网络的研究

本文对(蓖麻油-聚乙二醇)聚氨酯/聚甲基丙烯酸甲酯(PU/PMMA)互穿聚合物网络(IPN)体系进行了研究.实验结果表明:IPN的力学性能受网络化学构型控制.在PU/PMMA为25/75时,应力-应变曲线出现屈服点,产生类似皮革行为,并在此点抗张强度最高,表现明显的协同效应.动态力学性能及电镜均证明该体系相分离十分严重,通过加入扩链剂及网间交联剂能显著改善两组分相容性,其中网间交联剂效果最好。     

疏水/亲水性大孔聚二乙烯基苯/聚丙烯酰乙二胺互贯网络的合成及对水溶液中双酚A的吸附研究

采用分步悬浮聚合法制备了由大孔聚二乙烯基苯和聚丙烯酸甲酯组成的聚合物互贯网络(Interpenetrating polymer networks IPN),经过乙二胺氨解,得到由疏水性的大孔聚二乙烯基苯和亲水性的聚丙烯酰乙二胺组成的聚合物互贯网络(polydivinylbenzene/polyacrylethylenediamine IPN即PDVB/PAEM IPN),测定了合成的IPN的物理和化学结构,研究了PDVB/PAEM IPN对pH 6.5的水溶液中双酚A (Bisphenol A即BPA)的吸附性能.结果表明,合成的PDVB/PAEM IPN是含有氨基和酰胺基的多孔性IPN;树脂对水溶液申双酚A的等量吸附焓在20kJ/mol～50kJ/mol之间;动态吸附及脱附实验表明,湿态PDVB/PAEM IPN树脂对水溶液中双酚A的饱和吸附量达到约30mg/mL.树脂可以通过乙醇再生.     

疏水/亲水性聚二乙烯基苯/聚丙烯酸大孔互穿聚合物网络树脂对苯胺的吸附性能

采用分步悬浮聚合法制备了聚二乙烯基苯/聚丙烯酸甲酯（PDVB/PMA）大孔互穿聚合物网络,将其中的聚丙烯酸甲酯转化为聚丙烯酸,得到具有疏水/亲水性能的聚二乙烯基苯/聚丙烯酸（PDVB/PAA）大孔互穿聚合物网络（IPN）,研究了这类疏水/亲水大孔PDVB/PAA IPN对苯胺的吸附热力学和吸附动力学,测定了该树脂的孔结构、含水量、弱酸交换量和溶胀性能;测定了该树脂对苯胺在不同温度下的吸附等温线,利用热力学函数关系计算了吸附焓、自由能和熵。 红外光谱显示,成功合成了疏水/亲水PDVB/PAA IPN,与PDVB、PDVB/PMA IPN树脂相比,其BET表面积以及孔容均减小,含水量为62.73％,弱酸交换量为1.91 mmol/g;对苯胺的吸附为放热、自发的过程;溶胀实验、静态解吸实验表明,PDVB/PAA IPN树脂中疏水性的PDVB网具有疏水作用吸附能力,亲水性的PAA网具有氢键作用吸附能力。 对苯胺的吸附在90 min时即可达到吸附平衡,树脂吸附苯胺符合一级速率方程,吸附速率主要受颗粒内扩散的控制,同时还受液膜扩散的影响,吸附动力学可采用HSDM模型描述。     

聚醋酸乙烯酯/聚丙烯酸甲酯互穿网络聚合物的研究 Ⅴ.互穿缠结对相区结构的稳定作用

用定量的甲苯溶胀聚醋酸乙烯酯/聚丙烯酸甲酯互穿网络聚合物(PVAc/PMA IPN),使体系处于分相的热力学条件;或醇解其中的PVAc 网络,即增加两组份的化学不相容性.动态力学谱和透射电镜等结果表明,IPN 和网络Ⅰ的交联密度较高的半 IPN 试样,没有发生进一步的相分离,证明网络互穿缠结是永久性的物理缠结,并且有强迫互容作用的存在.     

蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物作为带锈涂料及粘合剂的可能性

在室温用氧化还原引发剂将蓖麻油、甲苯二异氰酸酯及取代乙烯合成了蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物（ＩＰＮ），研究了不同组成对带锈铁板搭接剪切强度的影响。指出搭接剪切强度随取代乙烯均聚物的玻璃化温度增加而增。ＮＣＯ／ＯＨ之比愈大，搭接剪切强度也愈大。以蓖麻油聚氨酯／（丙烯腈－苯乙烯）共聚物的反应液作为带锈铁板的涂料，其涂膜性能良好。用扫描电镜观察了此种涂料与带锈铁板的结合状态，并讨论其成因。     

含偶氮苯并噻唑发色团的二阶非线性光学互穿网络聚合物

合成了含偶氮苯并噻吩（ＢＴ）发色团的聚氨酯／环氧树脂互穿网络聚合物（ＩＰＮ）,其中聚氨酯网络由（丙烯酸β羟丙酯 ＢＴ ２甲基丙烯酸酯）共聚物与苯酚封闭的双端异氰酸酯的ＢＴ １反应形成,而环氧树脂网络由含环氧基的ＢＴ与含ＢＴ的苯二胺反应形成．同时实施这二种反应即形成ＩＰＮ．ＩＰＮ经红外光谱、凝胶含量测定及ＤＳＣ等表征．其薄膜经１６０℃、８５ｋＶ电晕极化,由可见光谱测量及一维刚性取向气体模型计算得到宏观二阶非线性光学极化系数χ（２）为２１８×１０－７ｅ．ｓ．ｕ．,在１２０℃经２４０ｈ序参数几乎不变．     

Room temperature synthesis and mechanical properties of two kinds of elastomeric interpenetrating polymer networks based on castor oil

Two kinds of interpenetrating polymer networks (IPNs) composed of two-component polyurethane (PU) and vinyl or methacrylic polymer (PV), namely, (polyether-castor oil)PU/PV IPN(I) and (polybutadiene-castor oil)PU/PV IPN(II), were synthesized at room temperature using benzoyl peroxide and N,N-dimethylaniline as redox initiator and dibutyltin dilaurate as catalyst. The former IPN was prepared by polymerization of castor oil, NCO-terminated polyether and vinyl or methacrylic monomer together and the latter IPN was obtained by polymerization of castor oil, NCO-terminated polybutadiene, NCO-terminated castor oil and vinyl or methacrylic monomer together. Various synthesis conditions affecting mechanical properties of the two kinds of IPNs were studied. Acrylonitrile (AN) is a good monomer for synthesizing IPN(I), but is a poor monomer for preparing IPN(II). At optimum conditions for the synthesis, both the (polyether-castor oil)PU/PAN IPNs and the (polybutadiene-castor oil)PU/polystyrene (PSt) IPNs possess permanent set about 10%, tensile strength over 13 and 11 MPa and ultimate elongation over 240% and 270%, respectively, thus behaving as elastomers. TEM micrograph of a (polybutadiene-castor oil)PU/PSt IPN showed a microphase separation in the IPN.     

聚苯乙烯/聚丙烯酸丁酯乳胶互穿聚合物网络的动态力学性能研究

<正> 互穿聚合物网络(IPN)是一种新型聚合物共混物.自Sperling在1969年合成聚丙烯酸乙酯/聚苯乙烯异步IPN(Sequential IPN)后,该领域进展很快.乳胶IPN(latex IPN)是用改进的乳液聚合法合成的一种微观互穿IPN.在前文中,我们报道了聚苯乙烯/聚丙烯酸丁酯(PS/PBA)乳胶IPN的合成,本文研究一些因素对PS/PBA乳胶IPN动态力学性能的影响.     

聚氨酯互穿聚合物网络阻尼性能研究进展

介绍了聚氨酯互穿聚合物网络（ＰＵ ＩＰＮ）作为阻尼材料的研究进展,分别讨论了聚氨酯（ＰＵ）／环氧树脂（ＥＰ）ＩＰＮ和ＰＵ／乙烯基聚合物ＩＰＮ的阻尼性,以及影响阻尼性能的因素,并比较了不同类型的ＰＵ ＩＰＮ的优缺点及新的可能的探讨方向。     

不饱和聚酯／聚氨酯互穿网络聚合物的合成

以醋酸酐封端的不饱和聚酯（ＦＵＰＲ）与交联聚氨酯预聚物制备了具有互穿聚合物网络（ＩＰＮ）的不饱和聚酯／聚氨酯，通过红外，ＤＳＣ和扫描电镜等分析了ＦＵＰＲ／ＰＵＩＰＮ网络形成的动力学，微相分离行为及力学性能，结果表明，当ＦＵＰＲ／ＰＵ达到某一比值时，产生网络互穿效应，可改善聚氨酯的刚性，提高不饱和聚酯的抗冲性。     

Interpenetrating polymer networks with stable second order nonlinear optical properties

Interpenetrating polymer networks (IPNs) based on polyurethane and polyacrylate-containing 4-(4'-nitrophenylazo) aniline chromophore groups were synthesized and characterized by infrared spectra, gel content and differential scanning calorimetry. Thin, transparent films of the IPNs were prepared by spin-coating, followed by thermal curing and corona poling. The poled IPN film shows very good optical properties and exhibits only one glass transition temperature. The second-order nonlinear optical (NLO) properties of the poled film were studied by visible light absorbance measurement according to one-dimensional rigid oriented gas model. The second-order nonlinear optical polarizability can reach 10^-7 e.s.u. The poled IPN film of defined composition showed a good temporal stability of NLO properties at 120°C for more than 160 hr.     

Mechanism of adhesion of polyurethane/polymethacrylate simultaneous interpenetrating networks adhesives to polymer substrates

Polyether-based polyurethane/poly (methyl methacrylate-co-ethyleneglycol dimethacrylate) interpenetrating polymer networks [PU/P (MMA–co–EGDMA)-IPNs] were synthesized and used as adhesives to adhere vulcanized natural rubber (NR) and soft polyvinyl chloride (PVC). The structure and morphology of the IPN adhesives in bulk and near the adhesive/substrate interfaces were investigated. A new mechanism of adhesion called conjugate interpenetration of networks across interfaces, which is suitable for IPN adhesives and polymer substrates, was put forward. According to this mechanism, while forming simultaneous interpenetrating networks in the adhesive, the monomers in the IPN adhesive can permeate polymer substrates and polymerize in situ to form gradient IPNs, thereby producing conjugate three-component IPNs near the adhesive/substrate interfaces. It is the conjugate interpenetration of the networks across the interfaces that strengthens interfacial combination remarkably and results in high bond strength of IPN adhesives. © 1994 John Wiley & Sons, Inc.     

Interpenetrating polymer networks of polyurethane and maleimide-terminated polyurethane for biomedical applications

Interpenetrating polymer networks (IPNs) of polyurethane (PU) and maleimide-terminated polyurethane (UBMI) were prepared by using a simultaneous polymerization technique. The effects of the UBMI molecular weight and amounts of the UBMI in the IPNs on the mechanical properties, dynamic mechanical properties, degree of compatibility, water absorption, surface properties and dynamic thrombosis were investigated. Bulk structure and surface properties were analyzed in order to correlate their blood compatibility. The IPNs exhibited a higher ultimate tensile strength especially when the UBMI with short soft chains was introduced. The heterogeneous characteristics were found for the IPNs when longer soft segment chains were incorporated in the PU component polymer. The presence of hydrophilic/hydrophobic alternative microdomains on the IPN surface was proposed to be the reason for good blood compatibility. The degree of compatibility, compositions of each domain and content of each domain in the matrix were calculated and correlated with the blood compatibility.