Effects of the stabilization temperature on the structure and properties of polyacrylonitrile-based stabilized electrospun nanofiber microyarns

Polyacrylonitrile (PAN) precursor nanofiber microyarns were successfully synthesized using a modified electrospinning method, and then were stabilized at different stabilization temperatures. Effects of stabilization temperature on the structure, thermal, and mechanical properties of stabilized microyarns were studied by FTIR, XRD, DSC, TG, and mechanical behavior test. It was found that when the stabilization temperature was above 250 °C, cyclization and dehydrogenation reactions were basically completed, and PAN crystal microstructure was almost completely destroyed, as well as the thermally stable ladder structure was formed. The results also showed that the strength of the stabilized microyarns increased to a threshold value and started to reduce thereafter as the stabilization temperature increased.     

Investigation of structural,optical and luminescent properties of sprayed N-doped zinc oxide thin films

N-doped ZnO (NZO) thin films are synthesized via spray pyrolysis technique in aqueous medium treating zinc acetate and N,N-dimethylformamide as precursors. Influence of N doping on structural, optical and luminescence properties have been investigated. Films are nanocrystalline having hexagonal crystal structure. Raman analysis depicts an existence of NZnO structure in NZO thin film. XPS spectrum of N 1s shows the 400 eV peak terminally bonded, well screened molecular nitrogen (γ-N₂). Lowest direct band gap of 3.17 eV has been observed for 10 at% NZO thin film. The UV, blue, and green deep-level emissions in photoluminescence of NZO films are due to Zn interstitials and O vacancies.     

Effect of the conditions of transfer on the structure and optical properties of Langmuir graphene oxide films during deposition on a substrate

The effect the solvent and transfer pressure of graphene oxide (SLGO) Langmuir–Blodgett films on the physicochemical properties of monolayers, and on their structural and optical properties, is studied. Examination of the physicochemical properties of SLGO monolayers on subphase surfaces that are formed from SLGO dispersions in different organic solvents reveals that monolayer behavior is virtually independent of the solvent. Electron microscope and optical studies show that the monolayers formed from SLGO dispersions in DMF and acetone have the highest transfer coefficients. It is concluded that the structural heterogeneity of the surfaces of graphene oxide films results from simultaneous effect of electrostatic interactions between graphene oxide particles and Van der Waals interactions with the solvation shell of the particles. Studies focusing on the effect the pressure of transferring a graphene oxide monolayer onto the surface of a solid substrate has on structural features of LB films show that films produced at low surface pressures have more homogeneous structures.     

Effect of precursor sol pH on microstructural, optical and photocatalytic properties of vacuum annealed zinc tin oxide thin films on glass

Dip coated vacuum annealed zinc tin oxide thin films on soda lime silica glass have been deposited from the precursor sols containing zinc acetate dihydrate and tin (IV) chloride pentahydrate (Zn:Sn = 67:33, atomic ratio in percentage) in 2-methoxy ethanol by varying sol pH (0.85–5.5). Crystallinity, morphology, optical and photocatalytic properties of the films strongly depend on sol pH. Measurement of grazing incidence X-ray diffraction confirms the presence of hexagonal nano ZnO in the films derived from the sols of pH < 5.5. Film crystallinity deteriorates on increasing sol pH and the film deposited from the sol of pH 5.5 shows XRD amorphous but the selected area diffraction pattern and HRTEM image evidence the presence of nano Zn₂SnO₄ (size, 5–6 nm). Direct band gap energy of films increases on increasing sol pH. To visualize the film surface microstructure, FESEM study has been done and a rod-like surface feature is revealed in the film deposited from the sol of pH 2.85. A dependence of precursor sol pH on the photocatalytic activity of films towards degradation of Rhodamine 6G dye under UV (254 nm) irradiation is found and the highest decomposition rate constant, ‘k’ value is obtained from the film prepared from the sol of pH 5.5. The presence of zinc deficient nano Zn₂SnO₄ in the film may consider for generating the highest ‘k’ value. We also measure gelling time, viscosity of sols as well as UV and FTIR studies on the films and propose chemical reactions.     

Controlling electrospun nanofiber morphology and mechanical properties using humidity

Electrospinning is a fiber spinning technique used to produce nanoscale polymeric fibers with superior interconnectivity and specific surface area. The fiber diameter, surface morphology, and mechanical strength are important properties of electrospun fibers that can be tuned for diverse applications. In this study, the authors investigate how the humidity during electrospinning influences these specific properties of the fiber mat. Using two previously uninvestigated polymers, poly(acrylonitrile) (PAN) and polysulfone (PSU) dissolved in N,N‐Dimethylformamide (DMF), experimental results show that increasing humidity during spinning causes an increase in fiber diameter and a decrease in mechanical strength. Moreover, surface features such as roughness or pores become evident when electrospinning in an atmosphere with high relative humidity (RH). However, PAN and PSU fibers are affected differently. PAN has a narrower distribution of fiber diameter regardless of the RH, whereas PSU has a wider and more bimodal distribution under high RH. In addition, PSU fibers spun at high humidity exhibit surface pores and higher specific surface area whereas PAN fibers exhibit an increased surface roughness but no visible pores. These fiber morphologies are caused by a complex interaction between the nonsolvent (water), the hygroscopic solvent (DMF), and the polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Influence of solvents properties on morphology of electrospun polyurethane nanofiber mats

Segmented polyurethane (SPU) nanofiber mats were prepared by electrospinning technique using the combination of four different solvents viz. tetrahydrofuran, N,N′‐dimethyl formamide, N,N′‐dimethyl acetamide, and dimethyl sulfoxide. Morphology of the electrospun nanofibers was examined by field emission scanning electron microscope. Experimental results revealed that the morphologies of polyurethane nanofiber mats have been changed significantly with the solvent selection for the electrospinning. It was observed that the diameters and morphology of the SPU nanofibers were influenced greatly by the use of combination of solvents. The uniform polyurethane nanofibers without beads or curls could be prepared by electrospinning through the selection of combination of good conductive and good volatile solvent viz. 7.5 wt/v% of SPU in N,N′‐dimethyl formamide/tetrahydrofuran (30 : 70 v/v) solutions at 20 kV applied voltages and volume flow rate of 1 ml/min. On the basis of the results obtained from this investigation, it has been established that solvent selection is one of the driving factors for controlling the morphology of the polyurethane electrospun nanofiber mats. The well‐controlled morphology of electrospun polyurethane nanofiber mats could be useful for many potential industrial applications such as in biomedical, smart textiles, nanofiltration, and sensors. Copyright © 2013 John Wiley & Sons, Ltd.     

The synthesis and optical properties of different zinc oxide nanostructures

The tetrapod-like whiskers (T-ZnO), nanoaeroplanes, nanocombs, nanobelts, bead-like nanoforms and many other forms of hexagonal zinc oxide were synthesized by the chemical deposition process (CVD). From the experimental results it can be seen that the composition of source gases and the speed of oxidation are essential to the growth of each of these morphologies of zinc oxide. By controlling the growth conditions, one novel morphology of ZnO (bead-like nanoform) has been obtained. The ZnO tetrapod-like whiskers were grown without catalysts on the walls of quartz tube. The structure and morphology of the T-ZnO was characterized. All four legs of as-grown ZnO nanotetrapods are needle-like and hexagonal shaped and grow in the ±[0001] direction. The effect of synthesis conditions on the morphology and size T-ZnO was observed. Possible mechanisms of growth were investigated. The lengths of the legs of the tetrapods range from 1 to 15 μm and diameter varying from 0.03 to 1 μm during the synthesis. In the photoluminescence spectra T-ZnO clearly shows two maxima at UV and visible regions. The oxygen impurity, particularly, oxygen flow rates mainly influences on increasing (decreasing) at PL peaks. The maximum near of 590–610 nm (～2 eV), confirming the influence of native defects (oxygen vacancies and interstitials) on the PL intensity and optical quenching exciton peak.     

Effect of needle diameter on nanofiber diameter and thermal properties of electrospun poly(methyl methacrylate)

The effect of needle diameter on the resulting electrospun poly(methyl methacrylate) (PMMA) average nanofiber diameter has been evaluated for three different needle gauges. The resulting nanofibers were observed and analyzed by scanning electron microscopy (SEM), suggesting a lack of correlation between the needle diameter used and the resulting average nanofiber diameter. Thermogravimetric analysis (TGA) indicated an increase in the thermal stability of PMMA nanofibers when compared to powdered PMMA, while differential scanning calorimetry (DSC) studies evidenced lower glass transition temperatures (Tg) for PMMA nanofibers in the first heating cycle. Copyright © 2007 John Wiley & Sons, Ltd.     

Liquid crystal alignment properties on surface-reformed solution-derived lanthanum-doped zinc oxide films

Liquid crystal (LC) alignment characteristics were investigated using a solution-derived lanthanum-doped zinc oxide (La:ZnO) film that was exposed to various intensities of ion-beam (IB) irradiation. At an IB intensity of 1700 eV, uniform and homogeneous LC alignment was achieved, as revealed by cross-polarized optical microscopy and pre-tilt angle measurement. Field-emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to verify that the IB irradiation induced physical and chemical surface reformation of the La:ZnO film that relate to LC alignment. FE-SEM and AFM revealed that the IB irradiation reformed the existing surface structure into a new structure with an altered surface roughness. The XPS results showed that the van der Waals force with anchoring energy increased as the IB intensity increased, and this profoundly affected the state of LC alignment. The capacitance-voltage (C-V) hysteresis curve was measured as a function of IB intensity to characterize the accumulated charge as a residual DC. Nearly zero C-V hysteresis was achieved at an IB intensity of 1700 eV. Therefore, a solution-derived La:ZnO film with an IB intensity of 1700 eV has great potential for high-quality LC applications.     

Structural characterization and mechanical properties of electrospun silk fibroin nanofiber mats

The regenerated silk fibroin dissolved in formic acid was electrospun into nanofiber mats. Structural characteristics of the spun as received and methanol and ethanol treated fibers were examined using the Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction. Mechanical properties and air permeability of the electrospun mats were also studied. IR spectroscopy and X-ray diffractometry showed random coil conformation and amorphous structure for as-spun fibers while typical FTIR spectra and X-ray diffractograms of β-sheet crystalline structure were recorded for the methanol and ethanol treated fibers. The mechanical properties of the mats were found to be dependent on fiber diameter. The mats containing fibers with smaller diameter had higher tensile strength but lower breaking strain. Methanol and ethanol treatment enhanced tensile strengths of the mats at the expenses of their breaking strain. Air permeability and pore size of the mats are strongly associated with diameter of the electrospun fibers.     

Effect of gallium oxide dopants on electrophysical and sorption properties of zinc oxide

The effect of gallium oxide dopants (0.1–0.3 at.% Ga) on the electrophysical and sorption properties of ZnO was studied in the temperature range from 19 to 350 °C. The introduction of the dopant increasing the conductivity of ZnO is accompanied by a change in the amounts of SO₂ and Cl₂ sorbed and the reactivity of zinc oxide. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 266–270, February, 1999.     

Effect of lithium oxide dopants on electrophysical and sorption properties of zinc oxide

The effects of lithium oxide dopants (0.5–0.8 at. % Li) on the electrophysical and sorption properties of ZnO were studied in the temperature range from 150 °C to 410 °C. The introduction of lithium increases the activation energy of the conductivity of ZnO, decreases its conductivity, and increases the amount of S0₂ sorbed. Two forms of chemisorbed SO₂ (donor and acceptor) are observed on the surface.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 1096–1100, May, 1996.     

Synthesis and characterization of electrospun PVdF-HFP/silane-functionalized ZrO2 hybrid nanofiber electrolyte with enhanced optical and electrochemical properties

A facile method to produce a hybrid of organic-inorganic nanofiber electrolyte via electrospinning is hereby presented. The incorporation of functionalized zirconium oxide (ZrO₂) nanoparticles into poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and complexed with lithium trifluoromethanesulfonate (LiCF₃SO₃) provided an enhanced optical transmissivity and ionic conductivity. The dependence of the nanofiber's morphology, optical and electrochemical properties on the various ZrO₂ loading was studied. Results show that while nanofiller content was increased, the diameter of the nanofibers was reduced. The improved bulk ionic conductivity of the nanofiber electrolyte was at 1.96 × 10⁻⁵ S cm⁻¹. Owing to the enhanced dispersibility of the 3-(trimethoxysilyl)propyl methacrylate (MPS) functionalized ZrO₂, the optical transmissivity of the nanofiber electrolyte was improved significantly. This new nanofiber composite electrolyte membrane with further development has the potential to be next generation electrolyte for energy efficient windows like electrochromic devices.     

Effect of protons on the optical properties of oxide nanostructures

Site-specific functionalization of oxide nanostructures gives rise to novel optical and chemical surface properties. In addition, it can provide deeper insights into the electronic surface structure of the associated materials. We applied chemisorption of molecular hydrogen, induced by ultraviolet (UV) light, followed by vacuum annealing to MgO nanocubes to selectively decorate three-coordinated oxygen ions (oxygen corner sites, for simplicity) with protons. Fully dehydroxylated nanocubes exhibit 3.2 +/- 0.1 eV photoluminescence induced by 4.6 eV light, where both emission and absorption are associated with three-coordinated oxygen sites. We find that partially hydroxylated nanocubes show an additional photoluminescence feature at 2.9 +/- 0.1 eV. Interestingly, the excitation spectra of the 2.9 and 3.2 eV emission bands, associated with protonated and nonprotonated oxygen corner sites, respectively, nearly coincide and show well-pronounced maxima at 4.6 eV in spite of a significant difference in their local atomic and electronic structures. These observations are explained with the help of ab initio calculations, which reveal that (i) the absorption band at 4.6 eV involves four-coordinated O and Mg ions in the immediate vicinity of the corner sites and (ii) protonation of the three-coordinated oxygen ions eliminates the optical transitions associated with them and strongly red-shifts other optical transitions associated with neighboring atoms. These results demonstrate that the optical absorption bands assigned to topological surface defects are not simply determined by the ions of lowest coordination number but involve contributions due to the neighboring atoms of higher coordination. Thus, we suggest that the absorption band at 4.6 eV should not be regarded as merely a signature of the three-coordinated O2- ions but ought to be assigned to corners as multiatomic topological features. Our results also suggest that optical absorption signatures of protonated and nonprotonated sites of oxide surfaces can be remarkably similar.     

Effect of structure on properties of polypyromellitimide films

Polypyromellitimides were prepared by the reaction of di(4-aminophenyl) ether (E)/di (4-aminophenyl) methane (M), and pyromellitic dianhydride in dimethylformamide, followed by thermal cyclization in a nitrogen atmosphere. Copolyimides were obtained by taking different molar ratios of diamines in the initial monomer feed. Differential scanning calorimetric, thermogravimetric analysis, and thermally stimulated current studies were carried out on these samples. It was concluded that the dielectric relaxation in these copolymers is due to trapping of the charge carriers. The dielectric relaxation parameters and activation energies were also calculated.     

Influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films

The influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films has been investigated. As-deposited films were pyrolyzed at 300 °C for 30 min and at 500 °C for 10 min. Final annealing was done at 600 °C for 30 min in air. The as-grown films deposited on soda-lime-silica glass substrates were highly c-axis oriented. Distinct grain structure was present in the film pyrolyzed at 500 °C, while the surface of the film pyrolyzed at 300 °C was smooth and no observed texture. The surface of ZnO pyrolyzed at 300 °C was covered with needle-like grain growth. With increasing pyrolysis temperature at 500 °C, a three-dimensional island formation was appeared.     

Solvent and concentration effects on the properties of electrospun poly(ethylene terephthalate) nanofiber mats

This study describes the preparation and characterization of nanofibrous mats obtained by electrospinning poly(ethylene terephthalate) (PET) solutions in trifluoroacetic acid/dichloromethane (TFA/DCM). Special attention was paid to the effect of polymer concentration and solvent properties on the morphology, structure, and mechanical and thermal properties of the electrospun nonwovens. The results show that the spinnable concentration of PET solution in TFA/DCM solvents is above 10 wt %. Mats have nanofibrous morphology with fibers having an average diameter in the range of 200–700 nm (depending on polymer concentration and solvent composition) and an interconnected pore structure. Higher solution concentration favors the formation of uniform fibers without beads and with higher diameter. Morphology and fiber assembly changed with the solvent properties. Solvent mixtures rich in TFA, i.e., those with higher dielectric constant and lower surface tension, originated fibers with small diameter. However, due to the lower volatility, those solvent mixtures also produced more branched and crosslinking fibers, with less morphologic uniformity. Mechanical properties (Young's modulus, ultimate strength, and elongation at break) and thermal properties (glass transition, crystallization, and melting) have been studied for the PET electrospun nanomats and compared with those of the original polymer. Solvent effect on fiber crystallinity was not significant, but a complex effect was observed on the mechanical properties of the electrospun mats, as a consequence of the different structural organization of the fibers within the mat network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 460–471, 2008     

Effect of sol temperature on the structure,morphology, optical and photoluminescence properties of nanocrystalline zirconia thin films

Transparent nanocrystalline zirconia thin films were prepared by sol–gel dip coating technique using Zirconium oxychloride octahydrate as source material on quartz substrates, keeping the sol at room temperature (SET I) and 60 °C (SET II). X-ray diffraction (XRD) pattern shows the formation of mixed phase [tetragonal (T) + monoclinic (M)] in SET I and a pure tetragonal phase in SET II ZrO₂ thin films annealed at 400 °C. Phase transformation from tetragonal to monoclinic was achieved in SET II film annealed at 500 °C. Atomic force microscopy analysis reveals lower rms roughness and skewness in SET II film annealed at 500 °C indicating better optical quality. The transmittance spectra gives a higher average transmittance >85% (UV–VIS region) in SET II films. Optical spectra indicate that the ZrO₂ films contain direct—band transitions. The sub- band in the monoclinic ZrO₂ films introduced interstitial O⁻defect states above the top of the valance band. The energy bandgap increased (5.57–5.74 eV) in SET I films and decreased (5.74–5.62 eV) in SET II films, with annealing temperature. This is associated with the variations in grain sizes. Photoluminescence (PL) spectra give intense band at 384 and 396 nm in SET I and SET II films, respectively. A twofold increase in the PL intensity is observed in SET II film. The “Red” shift of SET I films and “Blue” shift of SET II films with annealing temperature, originates from the change of stress of the film due to lattice distortions.