A new method to determine biological sample volume by short end multiple injection capillary electrophoresis: application in determination of nitrate and thiocyanate in human saliva

The aim of this study was to develop a simple and rapid method of capillary electrophoresis using a short end multiple injection in free solution to determine simultaneously the biological sample volume and analytes concentration. The method consists of a sequence of injection steps with an internal standard as the reference for correction of the volume of sample collected. The procedure was applies in the determination of NO(3)(-) and SCN in saliva samples. The background electrolyte was composed of 12 mM tris(hydroxymethyl)aminomethane and 8.5mM sulfuric acid, at pH 2.5. The internal standard used was BrO(3)(-). A fused silica capillary (48.5 cm total length, 8.5 cm effective length and 75 μm i.d.) coated with chitosan was used in a short-end injection configuration. Modification of the electroosmotic flow (EOF) using dynamic coating resulted in a controlled and stable EOF, contributing to the rapid separation of anions (0.36 min) in co-electroosmotic mode. The validation of the method for correcting the volume of saliva collected with a swab showed a difference of less than 3.5% compared with the predicted value and a correlation of 0.999. The limits of detection for NO(3)(-) and SCN(-) were 0.13 and 0.23 mg L(-1), respectively. The inter-day precision of the method determined for both analytes was less than 5% and the recovery ranged between 97 and 102%.     

Quantitative study on selective stacking of zwitterions in large-volume sample matrix by moving reaction boundary in capillary electrophoresis

The paper advanced the theoretical procedures for quantitative design on selective stacking of zwitterions in full capillary sample matrix by a cathodic-direction moving reaction boundary (MRB) in capillary electrophoresis (CE) under control of electroosmotic flow (EOF). With the procedures, we conducted the theoretical computations on the selective stacking of two test analytes of L-histidine (His) and L-tryptophan (Trp) by the MRB created with 30 mM pH 3.0 formic acid-NaOH buffer and 2-80 mM sodium formate. The results revealed the following three predictions. At first, the MRB cannot stack His and Trp plugs if less than 12.5 mM sodium formate is used to form the MRB and prepare the sample matrix. Second, the MRB can stack His and/or Trp sample plugs completely if higher than 50 mM sodium formate is chosen to form the MRB. Third, the MRB can only focus His plug completely, but stack Trp plug partially if 20-50 mM sodium formate is used; this implied the complete MRB-induced selective stacking to His rather than Trp. All the three predictions were quantitatively proved by the experiments. With great dilution of sample matrix and control of EOF, controllable, simultaneous and MRB-induced selective stacking and separation of zwitterions were achieved. The theoretical results hold evident significances to the quantitative design of selective stacking conditions and the increase of detection sensitivity of zwitterions in CE. In addition, the control of EOF by cetyltrimethylammonium bromide (CTAB) can evidently improve the stacking efficiency to both His and Trp.     

Simultaneous determination of nitrite, nitrate, thiocyanate and uric acid in human saliva by capillary zone electrophoresis and its application to the study of daily variations

Simultaneous determination of nitrite (NO2-), nitrate (NO3-), thiocyanate (SCN-) and uric acid in human saliva was performed by capillary zone electrophoresis using a coated capillary with reversed electroosmotic flow (EOF), using a 100 mM sodium phosphate buffer at pH 6.5 as a running buffer. Saliva samples were deproteinized with acetonitrile and filtered through a membrane filter. The important advantages of the reported method are: simple operation, short analysis time, minimal sample pre-treatment and sample dilution. In order to evaluate the daily variations of the anionic components, the concentrations were determined in the human saliva of four healthy volunteers upon waking and at 2qh intervals during a day.     

Sensitive determination of anions in saliva using capillary electrophoresis after transient isotachophoretic preconcentration

A transient isotachophoresis-capillary electrophoresis (tITP-CE) system for the determination of minor inorganic anions in saliva is described. The complete separation and quantification of bromide, iodide, nitrate, nitrite, and thiocyanate has been achieved with only centrifugation and dilution of the saliva sample. In-line tITP preconcentration conditions, created by introduction of the plugs of 5 mM dithionic acid (leading electrolyte) and 10 mM formic acid (terminating electrolyte) before and after the sample zone, respectively, allowed the limits of direct UV absorption detection (at 200 nm) to be up to 50-fold improved as compared with CE without tITP. As a result, nitrate and thiocyanate were still detectable at 4.6 and 3.8 μg l⁻¹, respectively, in 1000 times diluted saliva. The daily variations of anionic concentrations in saliva samples taken from a smoking health volunteer were discussed based on the results of tITP-CE analysis. It was confirmed that the thiocyanate concentration in saliva noticeably increased after smoking. This is apparently the first report on simultaneous quantification of more than four anionic salivary constituents using CE.     

Solid-phase extraction and large-volume sample stacking with an electroosmotic flow pump in capillary electrophoresis for determination of methotrexate and its metabolites in human plasma

This paper describes approaches for large-volume sample stacking (LVSS) with an EOF pumpin CE for the determination of methotrexate (MTX) and its metabolites in human plasma. After pretreatment of plasma through a SPE cartridge, a large sample volume was loaded by hydrodynamic injection (3 psi, 70 s) into the capillary filled with phosphate buffer (70 mM, pH 6.0) containing 0.01% polyethylene oxide. Following removal of a large plug of sample matrix from the capillary using polarity switching (-25 kV), the separation of anionic analytes was subsequently performed without changing polarity again, achieving an improvement of sensitivity of around a 100-fold. The method was applied to therapeutic drug monitoring of MTX in one acute lymphoblastic leukemia patient. This study is one of very few applications showing the feasibility of LVSS in analysis of biological samples by CE.     

Non-uniform surface charge distributions in CE: theoretical and experimental approach based on Taylor dispersion

The control of the EOF direction and magnitude remains one of the more challenging issues for the optimization of separations in CE. In this work, we investigated the possibility to use non-uniform surface charge distribution for the modulation of the EOF in CE. Non-uniform zeta potentials were obtained by modifying a section of the capillary surface using adsorption of polyelectrolytes. Three different methods were studied: (i) partial polycation coating on a fused silica capillary, (ii) partial polycation (or polyanion) coating on polyelectrolyte multilayers, and (iii) partial polycation coating on a capillary previously modified with poly(ethylene oxide). The magnitude and the direction of the EOF as a function of the coated capillary length were first studied. The stability of the EOF and the separation performances were also considered taking two dialanine diastereoisomers as model compounds. In partially coated capillaries, the average solvent flow is the sum of two contributions: a non-dispersive electroosmotic contribution related to the capillary surface charge, and a dispersive hydrodynamic contribution that depends on the difference of surface charge between the coated and the non-coated capillary zones. To get a better insight into the influence of the hydrodynamic contribution to the total peak dispersion, the peak variances corresponding to the Taylor dispersion, the injection plug, and the axial diffusion were calculated. This work demonstrates that peak dispersion in a capillary partially coated by the inlet end is different from that obtained when the coating is performed by the outlet end. Experimentally, the combination of a partially coated capillary with a large volume sample stacking preconcentration step can be used for injecting up to 95% of the capillary volume. This approach leads to a preconcentration factor of 60 compared with CZE with classical injection.     

毛细管电泳进样技术新进展

评述了毛细管电泳进样技术新成果。对直接在线进样，二维分离体系中毛细管电泳分离的增样，相关毛细管电泳增样，超微量样品及单个分子的进样，近端进样，双向进样和高温下的进样装置的应用状况作了介绍。     

Development of off-line and on-line capillary electrophoresis methods for the screening and characterization of adenosine kinase inhibitors and substrates

Fast and convenient CE assays were developed for the screening of adenosine kinase (AK) inhibitors and substrates. In the first method, the enzymatic reaction was performed in a test tube and the samples were subsequently injected into the capillary by pressure and detected by their UV absorbance at 260 nm. An MEKC method using borate buffer (pH 9.5) containing 100 mM SDS (method A) was suitable for separating alternative substrates (nucleosides). For the CE determination of AMP formed as a product of the AK reaction, a phosphate buffer (pH 7.5 or 8.5) was used and a constant current (95 microA) was applied (method B). The methods employing a fused-silica capillary and normal polarity mode provided good resolution of substrates and products of the enzymatic reaction and a short analysis time of less than 10 min. To further optimize and miniaturize the AK assays, the enzymatic reaction was performed directly in the capillary, prior to separation and quantitation of the product employing electrophoretically mediated microanalysis (EMMA, method C). After hydrodynamic injection of a plug of reaction buffer (20 mM Tris-HCl, 0.2 mM MgCl2, pH 7.4), followed by a plug containing the enzyme, and subsequent injection of a plug of reaction buffer containing 1 mM ATP, 100 microM adenosine, and 20 microM UMP as an internal standard (I.S.), as well as various concentrations of an inhibitor, the reaction was initiated by the application of 5 kV separation voltage (negative polarity) for 0.20 min to let the plugs interpenetrate. The voltage was turned off for 5 min (zero-potential amplification) and again turned on at a constant current of -60 microA to elute the products within 7 min. The method employing a polyacrylamide-coated capillary of 20 cm effective length and reverse polarity mode provided good resolution of substrates and products. Dose-response curves and calculated K(i) values for standard antagonists obtained by CE were in excellent agreement with data obtained by the standard radioactive assay.     

Adsorptive BSA Coating Method for CE to Separate Basic Proteins

A novel and simple coating method was developed by coating bovine serum albumin (BSA) onto the inner surface of a fused-silica capillary, to avoid the adsorption of analytes during CE. The advantage presented here was that the coating process is more simple, fast, stable, and reproducible. The coated capillary avoided the adsorption of analytes onto the inner surface of a fused-silica capillary and might be a promising candidate for separation of complex biological samples with further development. Meanwhile, the efficiencies of the coated capillary were evaluated by EOF, chromatographic peak shape, and theoretical plate number (N m^?1) of RNase A. The optimal coating conditions were obtained from the results. The pH value of coating buffer PB was 4.2, the standing time was 12 h at 4 °C, and the coating concentration of BSA was 1.5 mg mL^?1. The stability of the coating on the inner wall of the capillary and the reproducibility of the coated capillaries were good. The theoretical plate number values of RNase A were over 1.3 × 10⁵ (N m^?1) in the coated capillary. After successive electrophoresis for 48 h using the coated capillary, the RSD values of EOF and the theoretical plate number were 4.14 % and 9.14 %, respectively. In addition, the RSD values of EOF and the theoretical plate number (N m^?1) in the coated capillaries were 13.19 % and 8.96 %, respectively. Finally, the coated capillary was successfully applied to separate the mixture of four basic proteins (RNase A, lysozyme, trypsin and myoglobin).     

Separation of antidepressants by capillary electrophoresis with in-line solid-phase extraction using a novel monolithic adsorbent

The separation of three selective serotonin reuptake inhibitors (SSRIs) by capillary electrophoresis (CE) with fully integrated solid-phase extraction (SPE) is described. Polymeric monolithic SPE modules were prepared in situ within a fused silica capillary from either butyl methacrylate-co-ethylene dimethacrylate or 3-sulfopropyl methacrylate-co-butyl methacrylate-co-ethylene dimethacrylate. Using a 1 cm SPE module placed at the inlet of the capillary, a mixture of sertraline, fluoxetine and fluvoxamine was extracted from aqueous solution by applying a simple pressure rinse. Under pressure-driven conditions, efficient elution was possible from both SPE materials investigated using 50 mM phosphate buffer, pH 3.5 in acetonitrile (20/80, v/v). Two different strategies were investigated for the efficient elution and subsequent CE separation. Injection of an aqueous sample plug directly into the non-aqueous elution/separation buffer was found to be unsuitable with poor elution profiles observed in the electrodriven mode. Alternatively, a sample plug equivalent to several capillary volumes could be injected by pressure followed by filling the capillary with the non-aqueous elution/separation buffer from the outlet end using a combination of pressure and electrodriven flow. Using a neutral monolith, efficient elution/separation was not possible due to an unstable electroosmotic flow (EOF), however, by adding the ionisable monomer, 3-sulfopropyl methacrylate to the SPE module to increase and stabilise the EOF, it was possible to achieve efficient elution from the SPE module, followed by baseline separation by CE using a 200 mM acetate buffer, pH 3.5 in acetonitrile (10/90, v/v). With enrichment factors of over 500 achieved for each of the analytes this demonstrates the potential of in-line SPE-CE for the sensitive analysis of these drugs.     

Dual opposite injection electrokinetic chromatography: nonionic microemulsion pseudostationary phase and novel approach to electrokinetic sampling bias

Dual opposite injection capillary electrophoresis (DOI-CE) is a family of CE techniques in which the sample is introduced into both ends of the capillary. For the analysis of compounds with widely varying pKa values using a voltage-driven separation scheme, DOI-CE is superior to conventional CE with sample introduction at only one end of the capillary due to DOI-CE's broader elution window. To enhance the DOI-CE separation, a running buffer with a microemulsion system was developed. Since DOI-CE works best under conditions of low electroosmotic flow (EOF), the suppression of EOF via the addition of a multiply charged cation (e.g., Zn2+) to the buffer was investigated, and was found to suppress the EOF effectively at moderate concentrations (2.5-10 mM). Three different dual opposite injection modes were studied: simultaneous electrokinetic injection, sequential electrokinetic injection, and sequential hydrodynamic injection. The injection bias in the first two electrokinetic injection modes was compared with the sequential hydrodynamic injection. Corrections in the bias of the electrokinetic injections were discussed, and an improved approach was suggested. Finally, the effect of the relative concentration of the multiply charged cation in the sample plug and running buffer on the peak shape of co-electroosmotic and counter-electroosmotic ions was examined, and found to be much more influential on the latter.     

Simultaneous separation and enantioresolution of racemic local anesthetic drugs by capillary zone electrophoresis with Tween 20 and methyl-beta-cyclodextrin as selectors, employing a double plug technique

A new approach for simultaneous chiral and achiral separations by capillary zone electrophoresis is described. Two adjacent selector plugs, consisting of Tween 20 as an achiral and methyl-beta-cyclodextrin (CD) as a chiral selector, are employed and four related local anesthetics are used as model compounds. The principles of the partial filling technique, whereby the capillary is filled with the chiral selector solution followed by the micellar solution at different plug lengths and concentrations, prior to application of the solutes, was employed. During the run both capillary ends were dipped in a simple buffer, i.e., one without additives. The two separation media worked independently without any interaction. Separation of the solutes and their enantiomers was regulated by adjusting both the concentration and plug length (PL) of the micellar solution in the capillary, employing methyl beta-CD as chiral selector either at 38 or 76 mM. The solutes were separated on the basis of their affinity towards the micellar phase before they reached the methyl-beta-CD plug for enantioseparation. In the absence of the micellar plug, the enantiomers of prilocaine overlapped those of bupivacaine. The solutes and their enantiomers were completely separated by employing two adjacent plugs consisting of 100 mM Tween 20 solution (PL approximately 10 cm) and methyl-beta-CD solution at either 38 or 76 mM (PL approximately 30 cm).     

Phospholipid-lysozyme coating for chiral separation in capillary electrophoresis

A phospholipid coating with lysozyme as chiral recognition reagent permeated into the phospholipid membrane was developed for the chiral capillary electrophoretic (CE) separation of D- and L-tryptophan. As a kind of carriers, coated as phospholipid membranes onto the inner wall of a fused-silica capillary, liposomes are able to interact with basic proteins such as lysozyme, which may reside on the surface of the phospholipid membrane or permeate into the middle of the membrane. The interaction results in strong immobilization of lysozyme in the capillary. Coatings prepared with liposomes alone did not allow stable immobilization of lysozyme into the phospholipid membranes, as seen from the poor repeatability of the chiral separation. When 1-(4-iodobutyl)-1,4-dimethylpiperazin-1-ium iodide (M1C4) was applied as a first coating layer in the capillary, the electroosmotic flow (EOF) was effectively suppressed, the phospholipid coating was stabilized, and the lysozyme immobilization was much improved. The liposome composition, the running buffer, and the capillary inner diameter all affected the chiral separation of D- and L-tryptophan. Coating with 4 mM M1C4 and then 1 mM phosphatidylcholine (PC)/phosphatidylserine (PS) (80:20 mol%), with 20 mM (ionic strength) Tris at pH 7.4 as the running buffer, resulted in optimal chiral separation with good separation efficiency and resolution. Since lysozyme was strongly permeated into the membrane of the phospholipids on the capillary surface, the chiral separation of D- and L-tryptophan was achieved without lysozyme in the running buffer. The effects of different coating procedures and separation conditions on separation were evaluated, and the M1C4-liposome and liposome-lysozyme interactions were elucidated. The usefulness of protein immobilized into phospholipid membranes as a chiral selector in CE is demonstrated for the first time.     

Transient isotachophoresis of highly saline trace metals under strong electroosmotic flow conditions

Transient isotachophoresis (TITP) is usually performed under low-electroosmotic flow (EOF) conditions using a coated capillary or a low pH background electrolyte. We used a bare fused-silica capillary for TITP stacking of anionic complexes of some heavy metals under high-EOF conditions (pH 9.0). The sample component chloride as a leading electrolyte induced stacking by an isotachophoretic mechanism and the complexing agent 4-(2-pyridylazo) resorcinol (PAR) acted as a terminating electrolyte. The optimized background electrolyte was composed of 150 mM N-tris(hydroxymethyl)methyl-3-aminopropanesulfonic acid, 127 mM triethylamine, and 0.1 mM PAR at pH 9.0. The strong EOF at pH 9.0 pulled the analytes against their mobilities toward the outlet side, allowing a separation in the normal polarity mode. The stacking efficiency, reproducibility, analysis time, and sample loading capacity in coated and bare capillaries were compared. The stacking efficiency and reproducibility were higher and the analysis time was shorter in the coated capillary. However, a larger volume of a sample could be injected in the bare capillary to achieve detection limits comparable to those for the coated one without compromising the resolution between the analyte peaks. The limits of detection (S/N = 3) were in the sub-ppb range for the selected metals (Fe2+, 0.3 ppb; Ni2+, 0.16 ppb; and Zn2+, 0.8 ppb) in a standard saline sample with 250 mM NaCl matrix. The proposed method was successfully applied to the analysis of reference urine samples and human urine samples.     

Co‐electroosmotic capillary electrophoresis of basic proteins with 1‐alkyl‐3‐methylimidazolium tetrafluoroborate ionic liquids as non‐covalent coating agents of the fused‐silica capillary and additives of the electrolyte solution

The paper reports the results of a study carried out to evaluate the use of three 1‐alkyl‐3‐methylimidazolium‐based ionic liquids as non‐covalent coating agents for bare fused‐silica capillaries and additives of the electrolyte solutions (BGE) for CE of basic proteins in the co‐EOF separation mode. The three ionic liquids are differentiated from each other by the length of the alkyl group on the imidazolium cation, consisting of either an ethyl, butyl or octyl substituent, whereas tetrafluoroborate is the common anionic component of the ionic liquids. Coating the capillary with the ionic liquid resulted in improved peak shape and protein separation, while the EOF was maintained cathodic. This indicates that each ionic liquid is effective at masking the protein interaction sites on the inner surface of the capillary, also when its adsorption onto the capillary wall has not completely neutralized all the negative charges arising from the ionization of the silanol groups and the ionic liquid is not incorporated into the BGE employed for separation. Using the coated capillaries with BGE containing the ionic liquid employed for the coating, at concentration low enough to maintaining the EOF cathodic, both peak shape and protein separation varied to different extents, based on the particular ionic liquid used and its concentration. Fast and efficient separation of the model basic protein mixture in co‐electroosmotic CE is obtained with the 1‐butyl‐3‐methylimidazolium tetrafluoroborate coated capillary and 100 mM acetate buffer (pH 4.0) containing 4.4 mM 1‐butyl‐3‐methylimidazolium tetrafluoroborate as the BGE.     

Enantioseparation of tartaric acid by ligand‐exchange capillary electrophoresis using contactless conductivity detection

A method for the determination of tartaric acid enantiomers using CE with contactless conductivity detection has been developed. Cu(II) as a central metal ion together with l ‐hydroxyproline were used as a chiral selector, the BGE was composed of 7 mM CuCl_2, 14 mM trans‐4‐hydroxy‐l ‐proline, and 100 mM ε‐aminocaproic acid; the pH was adjusted to 5 by hydrochloric acid. Separation with a resolution of 1.9 was achieved in 9 min in a polyacrylamide‐coated capillary to suppress the EOF. Various counterions of the BGE were studied, and migration order reversal was achieved when switching from ε‐aminocaproic acid to l ‐histidine. With detection limits of about 20 μM, the method was applied to the analysis of wine and grape samples; only l ‐tartaric acid was found.     

Performance of throughout in-capillary derivatization capillary electrophoresis employing an on-line sample and run buffer loading device

We report on the effect on performance of varying the length of the capillary during throughout in-capillary derivatization (TICD) capillary electrophoresis (CE). Performance was evaluated by on-line coupling with a sample and CE runbuffer loading device that was newly introduced for this study. The device was assembled with a low cost using two 5 mm inner diameter (ID) disposable polyethylene syringes. First, a sequence was manually formed consisting of a 200 microL run buffer solution plug, a 100 microL sample plug and another 200 microL run buffer solution plug. Each plug was separated from its neighbor by a 100 microL air plug. When each plug reached the injection point where both a platinum-wire anode and the end of the separation capillary tube were located, 340 V/cm separation voltage (electrophoresis voltage) and 34 V/cm injection voltage were applied to the capillary for 3 s. Then the analytes were derivatized during migration in 50 microm ID capillaries filled with 2 mM o-phthalaldehyde (OPA)/N-acetylcysteine (NAC) in a 20 mM phosphate-borate buffer (pH 10), followed by separating and detecting of OPA derivatives by absorbance of 340 nm. Derivatization, separation, and detection were performed systematically using capillaries which varied in length from 5 to 80 cm. In the case of TICD-CE of a mixture containing 1 mM aspartic acid (Asp) and 20 mM m-nitorophenol (MNP) as a test solution, it was determined that peak area and peak width ratios of Asp to MNP did not depend on capillary length. Enantiomeric separations of DL-alanine (Ala) and Asp were examined using a run buffer consisting of a 45 microM beta-cyclodextrin (CD)-2 mM OPA/NAC-20 mM phosphate-borate buffer (pH 10). Even though the resolution of these enantiomeric pairs decreased with decreasing capillary length, as expected, the peaks corresponding to both enantiomeric amino acids were identified even when a 5 cm capillary was used. An 8-component amino acid mixture was also tested with 5 cm and 10 cm capillaries.     

Predefine resolution of enantiomers in partial filling capillary electrophoresis and two discontinuous function plugs coupling in‐capillary

In common partial filling CE (PF‐CE), the capillary contains the selectors plug between the injection and detector end to avoid the selector going into the detector zone. To expand this method, we propose a mode of two discontinuous function plugs coupling in‐capillary, named as plug–plug PF‐CE (ppPF‐CE). Initially, we present the method to predefine the effective length of chiral selector to meet the requirement of enantiomers' resolution, which could avoid some experimental procedures. With α‐CD as a chiral selector, a satisfactory resolution of enantiomers d,l ‐tryptophan and d,l ‐tyrosine was obtained with a partial filling α‐CD plug of optimal length and concentration. Subsequently, a second plug containing hydroxypropyl methylcellulose, organic solvents (acetonitrile and methanol), anionic and cationic surfactants (SDS and CTAB), and different concentrations of sodium phosphate buffer was inserted after the selector plug. Effects of plug–plug filling on enantiomers' migration and resolution are discussed. The ppPF‐CE might be a new flexible mode for CE application.     

Use of 1-alkyl-3-methylimidazolium-based ionic liquids as background electrolytes in capillary electrophoresis for the analysis of inorganic anions

Separation of inorganic anions in CE is often a challenging task because the electrophoretic mobilities of inorganic anions are comparable to or even greater than the EOF mobility. In this study, we present the use of ionic liquids (ILs) as background electrolytes (BGEs) in CE of inorganic anions. The 1-alkyl-3-methylimidazolium-based ILs as BGEs dynamically coated the capillary wall and induced a reversed EOF. This allowed the anions to comigrate with the EOF and yielded a rapid separation. Increasing the alkyl chain length of the ILs and BGE concentration can significantly improve the separation resolution. With 40 mM 1-butyl-3-methylimidazolium tetrafluoroborate as BGE, good separations of five model anions (Br-, I-, NO2(-), NO3(-), and SCN-) were achieved in a range of buffer pH values. The separation efficiency was as high as 34 600-155 000, and the RSDs of the migration times were less than 0.8% (n = 5).     

Enhanced sensitivity and resolution for the analysis of paralytic shellfish poisoning toxins in water using capillary electrophoresis with amperometric detection and field‐amplified sample injection

The profiling of the most lethal paralytic shellfish poisoning toxins (PSTs) in freshwater has increased the need to establish an alternative analytical method with high sensitivity and resolution. In this paper, a coupling technique of field‐amplified sample injection (FASI) and CE with end‐column amperometric detection (CE‐AD) was developed to improve the detection sensitivity and separation of PSTs by electrokinetically injecting a water plug of analytes to the capillary filled with a high‐conductivity BGE. Parameters affecting FASI and CE process were carefully adjusted to achieve the highest response and resolution. Separation selectivity for PSTs, especially for the analogues and epimers, was greatly enhanced by using 40 mM Britton–Robinson buffer (pH 9.5) as BGE, which altered the EOF and mobility of the analytes that interacted with polyborate ions. Satisfactory linear relationship between peak current and concentration of toxins were gained over a wide range of 1.95–254 μg/L. The detection limits (S/N = 3) for five PSTs ranged from 0.63 to 3.11 μg/L, which are below the health alert level in drinking water. In comparison with the up‐to‐date reporting chromatographic methods, the FASI‐CE‐AD method was simple, low‐cost, selective, and sensitive enough for direct quantification of PSTs at very low levels, implying a potential for screening and monitoring of PSTs in surface waters.