Green Synthesis of Fe and Fe/Pd Bimetallic Nanoparticles in Membranes for Reductive Degradation of Chlorinated Organics

Membranes containing reactive nanoparticles (Fe and Fe/Pd) immobilized in a polymer film (polyacrylic acid, PAA-coated polyvinylidene fluoride, PVDF membrane) are prepared by a new method. In the present work a biodegradable, non-toxic -"green" reducing agent, green tea extract was used for nanoparticle (NP) synthesis, instead of the well-known sodium borohydride. Green tea extract contains a number of polyphenols that can act as both chelating/reducing and capping agents for the nanoparticles. Therefore, the particles are protected from oxidation and aggregation, which increases their stability and longevity. The membrane supported NPs were successfully used for the degradation of a common and highly important pollutant, trichloroethylene (TCE). The rate of TCE degradation was found to increase linearly with the amount of Fe immobilized on the membrane, the surface normalized rate constant (k(SA)) being 0.005 L/m(2)h. The addition of a second catalytic metal, Pd, to form bimetallic Fe/Pd increased the k(SA) value to 0.008 L/m(2)h. For comparison purposes, Fe and Fe/Pd nanoparticles were synthesized in membranes using sodium borohydride as a reducing agent. Although the initial k(SA) values for this case (for Fe) are one order of magnitude higher than the tea extract synthesized NPs, the rapid oxidation reduced their reactivity to less than 20 % within 4 cycles. For the green tea extract NPs, the initial reactivity in the membrane domain was preserved even after 3 months of repeated use. The reactivity of TCE was verified with "real" water system.     

Atomic ensemble and electronic effects in Ag-rich AgPd nanoalloy catalysts for oxygen reduction in alkaline media

The ability to design and characterize uniform, bimetallic alloy nanoparticles, where the less active metal enhances the activity of the more active metal, would be of broad interest in catalysis. Herein, we demonstrate that simultaneous reduction of Ag and Pd precursors provides uniform, Ag-rich AgPd alloy nanoparticles (~5 nm) with high activities for the oxygen reduction reaction (ORR) in alkaline media. The particles are crystalline and uniformly alloyed, as shown by X-ray diffraction and probe corrected scanning transmission electron microscopy. The ORR mass activity per total metal was 60% higher for the AgPd(2) alloy relative to pure Pd. The mass activities were 2.7 and 3.2 times higher for Ag(9)Pd (340 mA/mg(metal)) and Ag(4)Pd (598 mA/mg(metal)), respectively, than those expected for a linear combination of mass activities of Ag (60 mA/mg(Ag)) and Pd (799 mA/mg(Pd)) particles, based on rotating disk voltammetry. Moreover, these synergy factors reached 5-fold on a Pd mass basis. For silver-rich alloys (Ag(≥4)Pd), the particle surface is shown to contain single Pd atoms surrounded by Ag from cyclic voltammetry and CO stripping measurements. This morphology is favorable for the high activity through a combination of modified electronic structure, as shown by XPS, and ensemble effects, which facilitate the steps of oxygen bond breaking and desorption for the ORR. This concept of tuning the heteroatomic interactions on the surface of small nanoparticles with low concentrations of precious metals for high synergy in catalytic activity may be expected to be applicable to a wide variety of nanoalloys.     

Facile synthesis of highly dispersed palladium/polypyrrole nanocapsules for catalytic reduction of p-nitrophenol

In this study, a facile one-step redox polymerization method for the preparation of highly dispersed palladium (Pd)/polypyrrole (PPy) nanocapsules has been demonstrated. During the polymerizaion process, the formation of RB-PdCl(4)(2-) complex via an electrostatic interaction plays a key role for the preparation of Pd/PPy composite nanocapsules. The well-dispersed Pd nanocrystals with small sizes of 2-4 nm embedded in PPy nanocapsules exhibited a good catalytic activity during the catalytic reduction of p-nitrophenol into p-aminophenol by NaBH(4) in aqueous solution. The kinetic apparent rate constant (k(app)) was about 8.87×10(-3) s(-1). Moreover, the as-prepared Pd/PPy composite nanocapsules exhibited a good reusability, which could be repeatedly used for the reduction of p-nitrophenol with a high catalytic activity for at least 10 successive cycles.     

Metal ion induced allosteric transition in the catalytic activity of an artificial phosphodiesterase

An artificial phosphodiesterase () bearing two types of metal binding sites, a catalytic site and a regulatory bipyridine site showed a unique allosteric transition in the catalytic activity against the metal concentration. The rate constants for the hydrolysis reaction of 2-hydroxypropyl-p-nitrophenyl phosphate (HPNP) and RNA dimer (ApA) with and without an effector metal ion were evaluated; the k(obs) value of HPNP hydrolysis for .(Zn(2+))(3) (2.0 x 10(-4) s(-1)) is 3.3 times larger than that for .(Zn(2+))(2). In the case of and Cu(2+), a 19.4 times larger k(obs) value was obtained for .(Cu(2+))(3) (1.2 x 10(-3) s(-1)) against .(Cu(2+))(2). The increase in the catalytic activity is ascribed to the allosteric conformational transition of induced by the coordination of effector metal ion to the Bpy moiety. A detailed investigation revealed that a conformational change of induced by the third M(2+) complexation enhances the rate of hydrolysis rather than a change in the substrate affinity.     

Pd/Co双金属纳米颗粒的制备及催化制氢性能

采用聚乙烯吡咯烷酮(PVP)保护的化学共还原法制备了Pd/Co双金属纳米颗粒, 研究了PVP及还原剂(NaBH₄)的用量、金属盐浓度、金属比例等对Pd/Co双金属纳米颗粒催化NaBH₄制氢性能的影响. 透射电子显微镜(TEM)的结果表明, 所制备的Pd/Co双金属纳米颗粒的平均粒径在1.5-2.8 nm之间. Pd/Co双金属纳米颗粒(BNPs)的催化活性远高于Pd与Co单金属纳米颗粒的活性; 当Pd/Co的理论原子比为1/9时, 双金属纳米颗粒的催化活性最高可达15570 mol·mol^-1·h^-1 (文中纳米颗粒的催化活性均为每摩尔Pd的活性). 密度泛函理论(DFT)的计算结果表明, Pd原子与Co原子之间发生电荷转移, 使得Pd原子带负电而Co原子带正电, 荷电的Pd和Co原子进而成为催化反应的活性中心. 所制备的Pd/Co双金属纳米颗粒具有很好的催化耐久性, 即使重复使用5次后, 该催化剂仍具有较高的催化活性, 且使用后的纳米颗粒催化剂也没有出现团聚现象. 双金属纳米颗粒催化NaBH₄水解反应的活化能约为54 kJ·mol^-1.     

Tailoring the morphology of Pd nanoparticles on CNTs by nitrogen and oxygen functionalization

The influence of N and O functionalization of CNT on the morphology of supported Pd-PVA nanoparticles is studied with respect to the catalytic activity in the liquid phase oxidation of benzyl alcohol to benzaldehyde. The impact of specific N and O sites on the carbon surface induced by the high temperature N-functionalization in the temperature range 673-873 K was observed by HRTEM as increased nanoparticles dispersion and enhanced metal wetting at the carbon surface. Those small nanoparticles that stabilized at the N-CNTs surface are beneficial for improving catalytic performance. The interaction of O(2) with the metal surface was studied by microcalorimetry. At 353 K, the PVA shell hinders the dissociative oxygen chemisorption at the surface of the fresh catalyst. Differently, a very high (maximum for Pd/N-CNT873K 750 kJ mol(-1)) and oscillating exothermic differential heat is registered for the washed samples. Such high differential heat on the "washed" sample is due to the sum of oxygen chemisorption and PVA oxidation. Thereby, it is demonstrated that the PVA overlayer suppresses the total combustion reaction pathway. This contribution has highlighted the impact of the dynamic change of morphology of these Pd nanoparticles under the reaction conditions on the catalytic performance and how this is modulated by the nature of the support as well as the PVA. The support with its varying ability to strongly bind Pd regulates the morphology of the nanoparticles on which the sub-surface penetration of O, H, C from the reactants depends, all modulating the electronic structure and thus the reactivity.     

Pd@tetrahedral hollow magnetic nanoparticles coated with N‐doped porous carbon as an efficient catalyst for hydrogenation of nitroarenes

Hollow magnetic nanoparticles (MNPs) with tetrahedral morphology were synthesized and then covered by a shell prepared by coating with melamine–formaldehyde followed by the introduction of glucose‐derived carbon. Subsequently, Pd nanoparticles were immobilized and the core–shell nanocomposite was carbonized. The obtained magnetic catalyst was successfully applied for the hydrogenation of nitroarenes in aqueous media. To investigate the effects of the morphology of MNPs, the nature of carbon shell, and the order of incorporation of Pd nanoparticles, several control catalysts, including the MNPs with different morphologies (disc‐like and cylinder); MNPs coated with different shells (sole glucose‐derived carbon or melamine–formaldehyde carbon shell); and a nanocomposite, in which Pd was immobilized after carbonization, were prepared and examined as catalyst for the model reaction. To justify the observed different catalytic activities of the catalysts, their Pd loadings, leaching, and specific surface areas were compared. The results confirmed that tetrahedral MNPs coated with porous N‐rich carbon shell exhibited the best catalytic activity. The high catalytic activity of this catalyst was attributed to its high surface area and the interaction of N‐rich shell with Pd nanoparticles that led to the higher Pd loading and suppressed Pd leaching.     

Study on the transesterification of methyl aryl phosphorothioates in methanol promoted by Cd(II), Mn(II), and a synthetic Pd(II) complex

Methanol solutions containing Cd(II), Mn(II), and a palladacycle, (dimethanol bis(N,N-dimethylbenzylamine-2C,N)palladium(II) (3), are shown to promote the methanolytic transesterification of O-methyl O-4-nitrophenyl phosphorothioate (2b) at 25 °C with impressive rate accelerations of 10(6)-10(11) over the background methoxide promoted reaction. A detailed mechanistic investigation of the methanolytic cleavage of 2a-d having various leaving group aryl substitutions, and particularly the 4-nitrophenyl derivative (2b), catalyzed by Pd-complex 3 is presented. Plots of k(obs) versus palladacycle [3] demonstrate strong saturation binding to form 2b:3. Numerical fits of the kinetic data to a universal binding equation provide binding constants, K(b), and first order catalytic rate constants for the methanolysis reaction of the 2b:3 complex (k(cat)) which, when corrected for buffer effects, give corrected (k(cat)(corr)) rate constants. A sigmoidal shaped plot of log(k(cat)(corr)) versus (s)(s)pH (in methanol) for the cleavage of 2b displays a broad (s)(s)pH independent region from 5.6 ≤ (s)(s)pH ≤ 10 with a k(minimum) = (1.45 ± 0.24) × 10(-2) s(-1) and a [lyoxide] dependent wing plateauing above a kinetically determined (s)(s)pK(a) of 12.71 ± 0.17 to give a k(maximum) = 7.1 ± 1.7 s(-1). Br?nsted plots were constructed for reaction of 2a-d at (s)(s)pH 8.7 and 14.1, corresponding to reaction in the midpoints of the low and high (s)(s)pH plateaus. The Br?nsted coefficients (β(LG)) are computed as -0.01 ± 0.03 and -0.86 ± 0.004 at low and high (s)(s)pH, respectively. In the low (s)(s)pH plateau, and under conditions of saturating 3, a solvent deuterium kinetic isotope effect of k(H)/k(D) = 1.17 ± 0.08 is observed; activation parameters (ΔH(Pd)(++) = 14.0 ± 0.6 kcal/mol and ΔS(Pd)(++)= -20 ± 2 cal/mol·K) were obtained for the 3-catalyzed cleavage reaction of 2b. Possible mechanisms are discussed for the reactions catalyzed by 3 at low and high sspH. This catalytic system is shown to promote the methanolytic cleavage of O,O-dimethyl phosphorothioate in CD3OD, producing (CD3O)2P═O(S(-)) with a half time for reaction of 34 min.     

电化学去合金化Pt(Pd)-Cu对氧的电催化还原活性的研究

应用电化学去合金法制备了表面覆盖有Pt(Pd)原子层的Pt(Pd)-Cu合金催化剂.研究该催化剂在0.1mol.L-1HClO4酸性溶液中对氧气电化学还原的催化活性,并采用同步辐射反常X-射线衍射法(Anomalous X-ray Diffraction,AXRD)和表面X-射线散射法(Surface X-ray Scattering,SXS)从原子尺度研究了去合金化后催化剂的结构.分析对比纳米颗粒、薄膜和单晶3种不同形式的去合金化Pt-Cu的结构和催化活性以及Pt-Cu和Pd-Cu两种不同合金薄膜的结构和催化活性.结果表明,表面应力是影响催化剂催化活性的关键因素,而应力大小则与去合金化后所形成的表面Pt(Pd)层的厚度相关,材料尺寸和组成元素等都影响表面Pt(Pd)层的厚度.提出可利用调控材料表面的应力来设计高催化活性的催化剂.     

Nanoporosities and catalytic activities of Pd-tailored single wall carbon nanohorns

The nanoporosities and catalytic activities of Pd nanoparticles dispersed on single wall carbon nanohorns (Pd-SWCNHs) and oxidized single wall carbon nanohorns (Pd-ox-SWCNHs) were examined. A transmission electron microscopy (TEM) observation indicated that Pd nanoparticles of 2-3 nm size were highly dispersed on both the SWCNHs. X-ray photoelectron spectra and N2 adsorption isotherms at 77 K illustrated the differences in the deposition process mechanisms of the Pd-SWCNHs and Pd-ox-SWCNHs; the deposition process depended on the surface functional groups. The supercritical H2 adsorption isotherms at 77 K suggested the relationships between the interaction of Pd-SWCNHs and Pd-ox-SWCNHs with H2 and the catalytic activities for a water formation reaction in a gas phase at 273 or 298 K. The catalytic activity measurement and TEM observation of the catalysts after the reactions demonstrated that the Pd-SWCNHs and Pd-ox-SWCNHs are promising catalysts.     

Catalytic activity and regeneration property of a Pd nanoparticle encapsulated in a hollow porous carbon sphere for aerobic alcohol oxidation

A core-shell composite consisting of a palladium (Pd) nanoparticle and a hollow carbon shell (Pd@hmC) was employed as a catalyst for aerobic oxidation of various alcohols. The core-shell structure was synthesized by consecutive coatings of Pd nanoparticles with siliceous and carbon layers followed by removal of the intermediate siliceous layer. Structural characterizations using TEM and N(2) adsorption-desorption measurements revealed that Pd@hmC thus-obtained was composed of a Pd nanoparticle core of 3-6 nm in diameter and a hollow carbon shell with well-developed mesopore (ca. 2.5 nm in diameter) and micropore (ca. 0.4-0.8 nm in diameter) systems. When compared to some Pd-supported carbons, Pd@hmC showed a high level of catalytic activity for oxidation of benzyl alcohol into benzaldehyde using atmospheric pressure of O(2) as an oxidant. The Pd@hmC composite also exhibited a high level of catalytic activity for aerobic oxidations of other primary benzylic and allylic alcohols into corresponding aldehydes. The presence of a well-developed pore system in the lateral carbon shell enabled efficient diffusion of both substrates and products to reach the central Pd nanoparticles, leading to such high catalytic activities. This core-shell structure also provided high thermal stability of Pd nanoparticles toward coalescence and/or aggregation due to the physical isolation of each Pd nanoparticle from neighboring particles by the carbon shell: this specific property of Pd@hmC resulted in possible regeneration of catalytic activity for these aerobic oxidations by a high-temperature heat treatment of the sample recovered after catalytic reactions.     

The oxidative degradation of dibenzoazepine derivatives by cerium(IV) complexes in acidic sulfate media

The kinetics of the oxidation of imipramine and desipramine using cerium(IV) complexes were studied in the presence of a large excess of azepine derivative (TCA) in acidic sulfate media using UV-Vis spectroscopy. The reaction proceeds via dibenzoazepine radical formation, identified by EPR measurements. The kinetics of the first degradation step were studied independently of the further slower degradation reactions. Linear dependences, with zero intercept, of the pseudo-first-order rate constants (k(obs)) on [TCA] were established for both dibenzoazepine radical formation processes. Rates of reactions decreased with increasing concentration of the H(+) ion indicating that cerium(IV) as well as both reductants exist in an equilibrium with their protolytic forms. The activation parameters for the degradation of dibenzoazepine derivatives in the first oxidation stage were as follows: ΔH(≠) = 39 ± 2 kJ mol(-1), ΔS(≠) = -28 ± 8 J K(-1) mol(-1) for imipramine and ΔH(≠) = 39 ± 2 kJ mol(-1), ΔS(≠) = -28 ± 6 J K(-1) mol(-1) for desipramine, respectively. Imipramine and desipramine radicals dimerized leading to an intermediate radical dimer, which decayed in a first-order consecutive decay process. These two further reactions proceed with rates which are characterized by non-linear dependences of the pseudo-first-order rate constants (k(obs)) on [TCA]. The degradation reaction of the intermediate radical dimer leads to an uncharged dimer as a final product. Mechanistic consequences of all the results are discussed.     

Functionalized cellulose-preyssler heteropolyacid bio-composite: An engineered and green matrix for selective,fast and in–situ preparation of Pd nanostructures: synthesis,characterization and application

A new and green engineered biocomposite was synthesized by sol–gel method, using different loadings of the Preyssler heterpolyacid (8, 15, 25, 40 and 50 wt%) on the functionalized microcrystaline cellulose surface. For the first time, this two-component polymeric biocomposite used for in-situ catalytic synthesis of Pd nanoparticles with the aim of producing tricomponent nanobiocomposites. Preyssler loading on the functionalized surface, controled the size and shape of Pd nanoparticles, time, and pH of their formation. All biocomposites and nanobiocomposites were characterised by FTIR, XRD, BET, TGA, SEM, EDS and TEM. The SEM analysis for two component polymeric biocomposites confirmed the presence of the Preyssler on the surface of functionalized cellulose. The formation of Pd nanoparticles on the surface, was observed by color changing (yellow to deep brown) and confirmed by UV–visible spectroscopy. The Pd nanoparticles formation was fast (2–4 min) for 8 wt% in pH = 2–3 at 80 °C. TEM analysis illustrated the spherical Pd nanoparticles with a size of 5–20 nm, at the lowest loading of Preyssler, and rod shapes with a size of 30–40 nm at the highest loading. The obtained nanobiocomposite exhibited high catalytic activity for the decolourisation of tartrazine, as a model of dyes pollutant in the industry with high degradation efficiency. The catalytic reactions were extended with other azo dyes including methyl orange and rodamine B.     

First principles investigations of Pd-on-Au nanostructures for trichloroethene catalytic removal from groundwater

Catalytic groundwater remediation from chlorinated organic solvents like trichloroethene (TCE) has been found to be more effective and sustainable than traditional non-destructive methods. Among the experimentally studied catalyst materials, Pd-decorated Au nanoparticles show the highest activity and selectivity combined with the best resistance towards poisoning by chemicals present in groundwater. In this study the thermochemistry and adsorption geometries of TCE and its hydrodechlorination products are investigated via density functional theory calculations. Various model systems for Pd-supported Au nanoparticles are addressed. The adsorption of TCE is endothermic on bare Au(111), almost thermoneutral or slightly exothermic on Pd-Au surface alloys and clearly exothermic on Pd overlayer structures on Au(111). The strongest chemisorption is on the di-σ configuration between Pd atoms over the smallest 2D Pd clusters containing only a few Pd atoms. These are not, however, the best catalysts as they are too small to co-adsorb hydrogen needed for hydrodechlorination reaction. We demonstrate good correlation between adsorption energies and the d-band center of the system. The variation of adsorption energy from the one Pd-Au composition to the other can be tentatively assigned to be due to the ligand and coordination effects. Also, the ensemble effects are important; without the right ensemble the adsorption is weak or endothermic.     

Hydrolysis of serine-containing peptides at neutral pH promoted by [MoO4]2- oxyanion

Hydrolysis of the dipeptides glycylserine (GlySer), leucylserine (LeuSer), histidylserine (HisSer), glycylalanine (GlyAla), and serylglycine (SerGly) was examined in oxomolybdate solutions by means of (1)H, (13)C, and (95)Mo NMR spectroscopy. In the presence of a mixture of oxomolybdates, the hydrolysis of the peptide bond in GlySer proceeded under neutral pD conditions (pD = 7.0, 60 °C) with a rate constant of k(obs) = 5.9 × 10(-6) s(-1). NMR spectra did not show evidence of the formation of paramagnetic species, excluding the possibility of Mo(VI) reduction to Mo(V), indicating that the cleavage of the peptide bond is purely hydrolytic. The pD dependence of k(obs) exhibits a bell-shaped profile, with the fastest cleavage observed at pD 7.0. Comparison of the rate profile with the concentration profile of oxomolybdate species implicated monomolybdate MoO(4)(2-) as the kinetically active complex. Kinetics experiments at pD 7.0 using a fixed amount of GlySer and increasing amounts of MoO(4)(2-) allowed for calculation of the catalytic rate constant (k(2) = 9.25 × 10(-6) s(-1)) and the formation constant for the GlySer-MoO(4)(2-) complex (K(f) = 15.25 M(-1)). The origin of the hydrolytic activity of molybdate is most likely a combination of the polarization of amide oxygen in GlySer due to the binding to molybdate, followed by the intramolecular attack of the Ser hydroxyl group.     

Billion-fold acceleration of the methanolysis of paraoxon promoted by La(OTf)3 in methanol

The methanolysis of the insecticide paraoxon (2) was investigated in methanol solution containing varying [La(OTf)(3)] (OTf = (-)OS(O)(2)CF(3)) as a function of at 25 degrees C. Plots of the pseudo-first-order rate constants (k(obs)) for methanolysis as a function of [La(OTf)(3)](total) were obtained under buffered conditions from 5.15 to 10.97, and the slopes of the linear parts of these were used to determine the second-order rate constants (k(2)(obs)) for the La(3+)-catalyzed methanolysis of 2. Detailed analysis of the potentiometric titration data of La(OTf)(3) in methanol through fits to a multicomponent equilibrium mixture of dimers of general stoichiometry La(3+)(2)((-)OCH3)n, where n assumes values of 1-5, gives the equilibrium distribution of each as a function of. These data, when fit to a second expression describing k(2)(obs) in terms of a linear combination of individual rate constants k(2)(2:1), k(2)(2:2).k(2)(2:)n for the dimers, allow one to describe the overall catalytic profile in terms of the individual contributions. The most catalytically important species are the three dimers La(3+)(2)((-)OCH3)1, La(3+)(2)((-)OCH3)2, and La(3+)(2)((-)OCH3)3. The catalysis of the methanolysis of 2 is spectacular: a 2 x 10(-3) M solution of [La(3+)](total), at neutral, affords a 10(9)-fold acceleration relative to the base reaction (t(1/2) approximately 20 s at 8.2) with excellent turnover. A mechanism of the catalyzed reaction involving the La(3+)(2)((-)OCH3)2 species is proposed.     

胶原纤维接枝多酚负载纳米钯的制备及其对硝基苯加氢的催化特性

以胶原纤维(CF)接枝表棓儿茶素棓酸脂(EGCG)为载体,制备了新型非均相钯(Pd)纳米催化剂(CF-EGCG-Pd).EGCG作为"桥分子"不仅对Pd纳米颗粒具有锚定作用,而且能控制Pd纳米颗粒的大小及分布.通过SEM、TEM、XRD、XPS对该催化剂的形貌和物理特性能进行了表征,发现该催化剂具有规整的纤维结构,在胶原纤维的外表面形成了高分散的平均粒径在3.8 nm的Pd纳米颗粒.将该催化剂用于硝基苯液相催化加氢反应,结果表明在308 K和1.0 MPa氢压下,硝基苯转化速率(TOF)达到34.13 mol·mol-1·min-1,苯胺选择性为100%,催化剂重复使用3次其催化活性基本不变.     

Catalase-peroxidase activity of iron(III)-TAML activators of hydrogen peroxide

Exceptionally high peroxidase-like and catalase-like activities of iron(III)-TAML activators of H 2O 2 ( 1: Tetra-Amidato-Macrocyclic-Ligand Fe (III) complexes [ F e{1,2-X 2C 6H 2-4,5-( NCOCMe 2 NCO) 2CR 2}(OH 2)] (-)) are reported from pH 6-12.4 and 25-45 degrees C. Oxidation of the cyclometalated 2-phenylpyridine organometallic complex, [Ru (II)( o-C 6H 4py)(phen) 2]PF 6 ( 2) or "ruthenium dye", occurs via the equation [ Ru II ] + 1/2 H 2 O 2 + H +-->(Fe III - TAML) [ Ru III ] + H 2 O, following a simple rate law rate = k obs (per)[ 1][H 2O 2], that is, the rate is independent of the concentration of 2 at all pHs and temperatures studied. The kinetics of the catalase-like activity (H 2 O 2 -->(Fe III - TAML) H 2 O + 1/2 O 2) obeys a similar rate law: rate = k obs (cat)[ 1][H 2O 2]). The rate constants, k obs (per) and k obs (cat), are strongly and similarly pH dependent, with a maximum around pH 10. Both bell-shaped pH profiles are quantitatively accounted for in terms of a common mechanism based on the known speciation of 1 and H 2O 2 in this pH range. Complexes 1 exist as axial diaqua species [FeL(H 2O) 2] (-) ( 1 aqua) which are deprotonated to afford [FeL(OH)(H 2O)] (2-) ( 1 OH) at pH 9-10. The pathways 1 aqua + H 2O 2 ( k 1), 1 OH + H 2O 2 ( k 2), and 1 OH + HO 2 (-) ( k 4) afford one or more oxidized Fe-TAML species that further rapidly oxidize the dye (peroxidase-like activity) or a second H 2O 2 molecule (catalase-like activity). This mechanism is supported by the observations that (i) the catalase-like activity of 1 is controllably retarded by addition of reducing agents into solution and (ii) second order kinetics in H 2O 2 has been observed when the rate of O 2 evolution was monitored in the presence of added reducing agents. The performances of the 1 complexes in catalyzing H 2O 2 oxidations are shown to compare favorably with the peroxidases further establishing Fe (III)-TAML activators as miniaturized enzyme replicas with the potential to greatly expand the technological utility of hydrogen peroxide.     

Kinetics and mechanism of large rate enhancement in the alkaline hydrolysis of N'-morpholino-N-(2'-methoxyphenyl)phthalamide

The apparent second-order rate constant (k OH) for hydroxide-ion-catalyzed conversion of 1 to N-(2'-methoxyphenyl)phthalamate (4) is approximately 10(3)-fold larger than k OH for alkaline hydrolysis of N-morpholinobenzamide (2). These results are explained in terms of the reaction scheme 1 --> k(1obs) 3 --> k(2obs) 4 where 3 represents N-(2'-methoxyphenyl)phthalimide and the values of k(2obs)/k(1obs) vary from 6.0 x 10(2) to 17 x 10(2) within [NaOH] range of 5.0 x 10(-3) to 2.0 M. Pseudo-first-order rate constants (k(obs)) for alkaline hydrolysis of 1 decrease from 21.7 x 10(-3) to 15.6 x 10(-3) s(-1) with an increase in ionic strength (by NaCl) from 0.5 to 2.5 M at 0.5 M NaOH and 35 degrees C. The values of k obs, obtained for alkaline hydrolysis of 2 within [NaOH] range 1.0 x 10(-2) to 2.0 M at 35 degrees C, follow the relationship k(obs) = kOH[HO(-)] + kOH'[HO (-)] (2) with least-squares calculated values of kOH and kOH' as (6.38 +/- 0.15) x 10(-5) and (4.59 +/- 0.09) x 10(-5) M (-2) s(-1), respectively. A few kinetic runs for aqueous cleavage of 1, N'-morpholino-N-(2'-methoxyphenyl)-5-nitrophthalamide (5) and N'-morpholino-N-(2'-methoxyphenyl)-4-nitrophthalamide (6) at 35 degrees C and 0.05 M NaOH as well as 0.05 M NaOD reveal the solvent deuterium kinetic isotope effect (= k(obs) (H 2) (O)/ k(obs) (D 2 ) (O)) as 1.6 for 1, 1.9 for 5, and 1.8 for 6. Product characterization study on the cleavage of 5, 6, and N-(2'-methoxyphenyl)-4-nitrophthalimide (7) at 0.5 M NaOD in D2O solvent shows the imide-intermediate mechanism as the exclusive mechanism.     

Serine protease mechanism-based mimics. Direct evidence for a transition state bridge proton in stable potentials

We have synthesized 1-(2-hydroxyacetyl)piperidine-2-one (2) and 1-(2-hydroxyacetyl)azepan-2-one (3). Equilibrium (K(f)) between the free alcohol (open form) and the tetrahedral intermediate (cyclol) is readily established, and both forms are observed in the D(2)O (1)H NMR spectra of 2 and 3. Therefore, their interconversion can be considered as an almost thermoneutral non-identical one. Pseudo-first-order rate constants (k(obs)) were obtained by simulating the AB (1)H NMR system observed for the cyclol. By best fitting the experimental points of a k(obs) versus pD profile to the equation k(obs) = 0.5k(0r) + 0.5k(r) K(ac)/(K(ac) + [D(+)]) + 0.5k(f)K(ao)/(K(ao)+ [D(+)]), the parameters involved were obtained: rate constants of rupture and formation (k(0r) and k(0f) = K(f)k(0r)) catalyzed by water, rate constants of rupture (k(r)) and formation (k(f)) from the conjugated bases of the cyclol form and the open form, and their acidity equilibrium constants K(ac) and K(ao). The system studied mimics the serine alcohol attack on the peptide bond and its reverse reaction in serine protease enzymes. In fact, the reaction rates are similar or perhaps even faster than the ones obtained for enzymatic reactions. The results also show the participation of water molecules forming catalytic proton bridges in stable potentials with the two interconverted forms. The position change of the bridged proton is sensitive to lactam ring size, and it is manifested by considerable change in the pKa values of both cyclol and open forms. Other evidence such as kinetics, DeltaS degrees , DeltaS, and proton inventory experiments and semiempirical molecular calculations support this proposal.