Structure and properties of the one-dimensional cobalt oxide CaCo2O4

We have studied crystal structure and transport properties of the quasi one-dimensional cobalt oxide CaCo₂O₄. The CaCo₂O₄ phase crystallizes in calcium-ferrite type structure, which consists of a corner- and edge-shared CoO₆ octahedron network including one-dimensional double chains. Large thermoelectric power (S  150 μV/K at 390 K) with metallic temperature dependence of S, moderate resistivity (ρ  2.9 × 10⁻¹ Ω cm at 390 K) with carrier localization at low temperature, and normal thermal conductivity (κ  6.3 W/Km at 390 K) were observed. The phonon mean-free path was calculated from the observed data, as a function of temperature. The long phonon mean-free path (l  24 Å at 300 K) implies that the thermal conductivity could be suppressed by impurity scattering of phonons with partial element substitution.     

Neutron polarization analysis on the multiferroic TbMn2O5

Polycrystalline TbMn₂O₅ was prepared by the standard solid-state reaction method and characterized by powder X-ray diffraction and magnetization to assure it is of single phase. Heat capacity measurements on the compound reveal an antiferromagnetic phase transition at 45 K. A broad peak below 6 K in the heat capacity measurements corresponds to the crossover transition of Tb³⁺ ordering. To confirm these magnetic orderings, neutron powder diffractions on TbMn₂O₅ with XYZ neutron polarization analysis were performed at the diffuse neutron scattering (DNS) spectrometer, FRJ-II, by using neutron wavelength of 4.8 Å in the temperature range of 1.8–250 K. Magnetic scattering was separated from nuclear coherent and spin incoherent scattering contributions. Long-range ordered magnetic peaks were observed below 39 K which is consistent with the heat capacity results. The drastic increasing intensities below 6 K indicate the ferromagnetic transition in Tb³⁺ orderings.     

Transport properties of single crystal

Transport properties of BaNi₂P₂ single crystals prepared by high-pressure synthesis method have been investigated. The temperature dependence of the resistivity is that of a typical metal with the anisotropy ratio ρ/ρ of 6.3 and suggests that electron–phonon interaction dominates the scattering mechanism. We have also found that the Hall effect and the magnetoresistance can be explained by a two-carrier model which is consistent with a multiple-band structure with both hole and electron characters.     

Spectroscopic investigation of arsenate and selenate incorporation into hydroxylapatite

The mechanism(s) of arsenate and selenate incorporation into hydroxylapatite (HAP) using extended X-ray absorption fine structure (EXAFS) spectroscopy was investigated for As- and Se-doped HAP samples with concentrations between 200 and 2500 ppm. EXAFS data on As and Se K-edges have shown similar local coordination environments and are similar to that of P in HAP, suggesting the substitution of arsenate or selenate tetrahedra on the phosphate sites. EXAFS best-fitting for As-doped samples shows that the first shell is fitted with approximately 4 O atoms at 1.68 Å, showing As(V) in tetrahedral coordination, and Se K-edge EXAFS data are characterized by the backscattering contributions an oxygen shell at 1.2 Å in the Fourier transform, which can be fit with 4 O atoms at 1.65 ± 0.01 Å. This is characteristic of Se–O distances in SeO₄ tetrahedron. These findings suggest that arsenate and selenate substitute for phosphate groups with local distortions during the incorporation of these metals into the structure of HAP.     

Quasi-distributed displacement sensor for structural monitoring using a commercial OTDR

A quasi-distributed displacement sensor for structural monitoring using an optical time domain reflectometer is demonstrated. Four displacement sensing heads are placed along a standard single mode optical fibre in several locations with different intervals. Their configurations introduce power loss through the decrease of their fibre loop radius when displacement is applied. The decrease of the light intensity with displacement variation is reported. Losses of 9 dB for a 120 mm displacement with a sensitivity of 0.027 dB/mm are reported. The quasi-distributed configuration is able to address sensors with 1 m distance resolution between them.     

Dynamics of the collective excitations of the quantum Hall system

Using the non linear optical technique of 3-pulse 4-wave mixing, we study the dynamics of the collective excitations of the quantum Hall system. We excite the system with 100 fs pulses propagating in directions k₁ and k₃ and then probe its time evolution with a delayed pulse k₂. We measure the non-linear optical response from the lowest Landau level along the direction k₁+k₂−k₃. As function of the time delay of pulse k₂, this signal shows striking beats for short time delays (500 fs), followed by a rise (20 ps) and then a decay (100 ps). We identify the microscopic origin of this dynamics by extending the standard theory of ultra fast nonlinear optics to include the effects of the correlations.     

Scanning tunneling microscopy/spectroscopy on multi-layered cuprate superconductor Ba2Ca5Cu6O12 (O1−x Fx)2

Scanning tunneling microscopy/spectroscopy (STM/STS) measurements on multi-layered cuprate superconductor Ba₂Ca₅Cu₆O₁₂ (O_1−x F_x)₂ are carried out. STM topographies show randomly distributed bright spot structures with a typical spot size of 0.8 nm. These bright spots are occupied about 28% per one unit cell of c-plane, which is comparable to the regular amount of apical oxygen of 20% obtained from element analysis. Tunneling spectra simultaneously show both the small and the large gap structures. These gap sizes at 4.9 K are about Δ 15 meV and 90 meV, respectively. The small gap structure disappears at the temperature close to T_C, while the large gap persists up to 200 K. Therefore, these features correspond to the superconducting gap and pseudogap, respectively. These facts give evidence for some ordered state with large energy scale even in the superconducting state. For the superconducting gap, the ratio of 2Δ/K_BT_C = 4.9 is obtained with T_C = 70 K, which is determined from temperature dependence of the tunneling spectra.     

Temperature dependent photoluminescence from ZnO/MgZnO multiple quantum wells grown by pulsed laser deposition

We have studied temperature dependent photoluminescence (PL) from ZnO Multiple Quantum Wells (MQWs) of different well layer thicknesses in the range 1–4 nm grown on (0001) sapphire by a novel in-house developed buffer assisted pulsed laser deposition. At 10 K the PL peak shifted toward blue with decreasing well layer thickness and at constant well layer thickness the PL peak shifted towards red with increasing temperature. To the best of our knowledge we have observed for the first time an efficient room temperature (RT) PL emanating from such MQWs. The red shift of the PL peak with increasing temperature has been found to be due to the band gap shrinkage in accordance with the Varshni’s empirical relation. The spectral linewidth was found to increase with increasing temperature due to the scattering of excitons with acoustic and optical phonons in different temperature regimes. Both at RT and at 10 K the PL peak shifted with respect to the well layer thickness in the range of 3.35–3.68 eV with decreasing thickness in agreement with the calculated values.     

Nucleation, growth and morphology of Co thin films on Ag(1 1 0)

Scanning tunneling microscopy (STM) experiments reveal that Co growth on Ag(1 1 0), at coverages of Co < 1 ML and low substrate temperatures (150 K), involves a concomitant insertion of Co into the top Ag layer and exchange of Ag out onto the surface. At 300 K, coverages of Co > 1 ML gives rise to a 3D nanocluster growth on the surface, with the clusters covered by Ag. Depending slightly on coverage, the clusters have a typical diameter of 3 nm and a height of 0.4 nm. Upon annealing to 500 K, major changes are observed in the morphology of the surface. STM and AES show that there is a reduction of the number of Co islands on the surface, partly due to subsurface Co cluster migration and partly due to sintering into larger clusters.     

Modification of photonic properties in porphyrin-infiltrated opal crystals

Structural, optical and magnetic properties of porphyrin-infiltrated opal hybrid structures were investigated. Bulk samples of synthetic opal were grown by sedimentation technique from colloidal solution of SiO₂ spheres of diameter 250 nm. The structure of the samples was examined by atomic force microscopy. The photonic properties of crystals were investigated by optical measurements in transmission and reflection modes. The stop band was observed in the region 510–550 nm. The photonic properties of synthetic opal crystals were modified by infiltration with aqueous basic solution of iron–porphyrin (FeTPPS) of concentration 1.0 mM. In hybrid samples the absorption bands typical of FeTPPS were observed in the vicinity of the opal stop band. Magnetic properties of FeTPPS-infiltrated opal samples have been studied at 5–300 K in magnetic fields up to 5 T. The FeTPPS-infiltrated opal crystals can be considered as the structures perspective for magnetophotonic devices.     

Photonic generation of microwave signal using a dual-wavelength single-longitudinal-mode distributed Bragg reflector fiber laser

In this paper, a novel all-optical microwave generation technique based on a dual-wavelength single-longitudinal-mode (SLM) distributed Bragg reflector (DBR) fiber laser is proposed and demonstrated. By exploiting spatial hole burning (SHB) effect, this laser could provide stable dual-wavelength SLM operation with a wavelength separation of 0.088 nm corresponding to the microwave signal at 10.484 GHz with a 3 dB bandwidth of 28 kHz. By appropriately adjusting the pump power, dual-wavelength oscillation could be maintained at different temperatures. We have theoretically analyzed the mechanism for microwave generation of the proposed DBR laser, and the calculated microwave frequency is in good agreement with our experimental results. Furthermore, experimental observation shows both of the laser wavelengths and generated microwave signals have good stability at room temperature.     

Carbon nanotube–polymer composites for photonic devices

We report the fabrication of high optical quality single wall carbon nanotube polyvinyl alcohol composites and their application in nanotube based photonic devices. These show a broad absorption of semiconductor tubes centred at 1.55 μm, the spectral range of interest for optical communications. The films are used as mode-lockers in an erbium doped fibre laser, achieving 700 fs mode-locked pulses. Raman spectroscopy shows no damage after a long time continuous laser operation.     

Arsenic-related recombination in MOVPE-grown ZnO/GaAs films

In this paper, ZnO films grown by metalorganic vapour phase epitaxy on various substrates (GaAs, silicon, sapphire) and using different VI /II ratios, are investigated by photoluminescence (PL) spectroscopy. The PL spectra of layers grown on GaAs show significant recombination at 3.320 eV, 3.305 eV and 3.270 eV. These energies are remarkably similar to what have been reported for hybrid beam deposited ZnO:As [Y.R. Ryu, T.S. Lee, H.W. White, Appl. Phys. Lett. 83 (2003) 87] and arsenic-implanted ZnO crystals [T.S. Jeong, M.S. Han, C.J. Youn, Y.S. Park, J. Appl. Phys. 96 (2004) 175], and the lines are ascribed to the incorporation of arsenic, which diffuses from the substrate into the films. Two acceptor levels are deduced at 120 meV and at 140–150 meV.     

Improvement of cubic silicon carbide crystals grown from solution

Cubic-silicon carbide crystals have been grown from carbon-rich silicon solutions using the travelling-zone method. To improve the growth process, we investigated the effect of controlling more tightly some of the growth parameters. Using such improved growth conditions, our best sample is a 12 mm diameter and 3 mm long 3C–SiC crystal. It is grown on a (0001) 2 off, 6H–SiC seed and has 111-orientation. The low amount of silicon inclusions results in a reduced internal stress, which is demonstrated by the consideration of μ-Raman spectra collected at room temperature on a large number of samples.     

High-performance pyroelectric single crystals for uncooled infrared detection applications

Uncooled pyroelectric infrared detectors based on ferroelectric single crystals 0.74Pb(Mg_1/3Nb_2/3)O₃–0.26PbTiO₃ (PMN–0.26PT) were fabricated. The performances of pyroelectric detectors dependence on detector fabrication temperature, absorption layer, and element thickness were compared. The room-temperature voltage responsivity (R_v) of 200 V/W and specific detectivity (D^*) of 10⁸ cm Hz^1/2/W at 12.5 Hz have been achieved. The results reveal that the better pyroelectric response can be expected by controlling temperature below 70 °C during the fabrication of the pyroelectric detectors, selecting absorption layer with high absorption coefficient, and decreasing the thickness of the elements.     

Electron drag in intermediate magnetic fields with low electron density

Electron drag between two two-dimensional electron systems has been measured in intermediate magnetic fields (/τ<ω_ck_BT) with a relatively low electron density. We explore, in this sample, the unusual increase of drag in intermediate magnetic fields which was well characterized by a nearly temperature independent B³ dependence. The anomalous behavior of electron drag observed in higher density samples is found to persist for low sample density.     

Effect of the synthesis route on the structural properties and shape of the indium oxide (In2O3) nano-particles

Nano-crystalline indium oxide (In₂O₃) particles have been synthesized by sol–gel and hydro-thermal techniques. A simple hydro-alcoholic solution consisting indium nitrate hydrate and citric acid (in sol–gel method) and 1, 4-butandiol (in hydro-thermal method) have been utilized. The structural properties of indium oxide nano-powders annealed at 450 °C (for both methods) have been characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and specific surface area (SSA) analysis. Structural analysis of the samples shows cubic phase in sol–gel and cubic-hexagonal phase mixture in hydro-thermally prepared particles. The nano-particles prepared by sol–gel method have nearly spherical shape, whereas hydro-thermally-made ones display wire- and needle-like shape in addition to the spherical shape. The obtained In₂O₃ nano-particles surface areas were 23.2 and 55.3 in sol–gel and hydro-thermal methods, respectively. The optical direct band gap of In₂O₃ nano-particles were determined to be 4.32 and 4.24 eV for sol–gel and hydro-thermal methods, respectively. These values exhibit 0.5 eV blue shift from that the bulk In₂O₃ (3.75 eV), which is related to the particle size reduction and approaching the quantum confinement limit of nano-particles.     

Dimensional evolution of silicon nanowires synthesized by Au–Si island-catalyzed chemical vapor deposition

This study explores the nucleation and morphological evolution of silicon nanowires (Si-NWs) on Si (0 0 1) and (1 1 1) substrates synthesized using nanoscale Au–Si island-catalyzed rapid thermal chemical vapor deposition. The Au–Si islands are formed by Au thin film (1.2–3.0 nm) deposition at room temperature followed by annealing at 700 °C, which are employed as a liquid-droplet catalysis during the growth of the Si-NWs. The Si-NWs are grown by exposing the substrates with Au–Si islands to a mixture of gasses SiH₄ and H₂. The growth temperatures and the pressures are 500–600 °C and 0.1–1.0 Torr, respectively. We found a critical thickness of the Au film for Si-NWs nucleation at a given growth condition. Also, we observed that the dimensional evolution of the NWs significantly depends on the growth pressure and temperature. The resulting NWs are 30–100 nm in diameter and 0.4–12.0 μm in length. For Si (0 0 1) substrates 80% of the NWs are aligned along the 1 1 1 direction which are 30° and 60° with respect to the substrate surface while for Si (1 1 1) most of the NWs are aligned vertically along the 1 1 1 direction. In particular, we observed that there appears to be two types of NWs; one with a straight and another with a tapered shape. The morphological and dimensional evolution of the Si-NWs is significantly related to atomic diffusion kinetics and energetics in the vapor–liquid–solid processes.     

Generation of laser-polarized xenon using fiber-coupled laser-diode arrays narrowed with integrated volume holographic gratings

Volume holographic gratings (VHGs) can be exploited to narrow the spectral output of high-power laser-diode arrays (LDAs) by nearly an order of magnitude, permitting more efficient generation of laser-polarized noble gases for various applications. A 3-fold improvement in ¹²⁹Xe nuclear spin polarization, P_Xe, (compared to a conventional LDA) was achieved with the VHG-LDA’s center wavelength tuned to a wing of the Rb D₁ line. Additionally, an anomalous dependence of P_Xe on the xenon density within the OP cell is reported—including high P_Xe values (>10%) at high xenon partial pressures (1000 torr).     

What can we learn about the spectrum of high-energy stray neutron fields from Bonner sphere measurements?

Extended-Range Bonner sphere spectrometers (ERBSSs) are well suited for measurements in high-energy stray neutron fields, where neutron energies extend from thermal to a few hundred MeV. These fields typically have a thermal peak, a fairly flat intermediate region, a medium energy peak at 1 MeV and a high-energy peak at a few 100 MeV. The data analysis is not straightforward: it requires unfolding with response functions that have a substantial amount of overlap, and the responses of the modified spheres (which provide information about the fluence at high energies) increase dramatically above 100 MeV. In this paper, I try to determine which of the main features of the spectrum are well determined by the data given optimal methods of analysis, and which features are subject to ambiguity. To do this, I analyse ERBSS measurements using two methods of analysis that are particularly useful for this purpose, Bayesian parameter estimation and maximum entropy unfolding.