Study of group-III binary and ternary nitrides using X-ray absorption fine structure measurements

It is demonstrated that the NEXAFS spectra are a “fingerprint” of the symmetry and the composition of the binary nitrides GaN, AlN and InN, as well as of their ternary alloys In_0.16Ga_0.84N and Al_yGa_1−yN. From the angular dependence of the N-K-edge NEXAFS spectra, the hexagonal symmetry of the under study compounds is deduced and the (p_x, p_y) or p_z character of the final state is identified. The energy position of the absorption edge (E_abs) of the binary compounds GaN, AlN and InN is found to red-shift linearly with the atomic number of the cation. The E_abs of the Al_yGa_1−yN alloys takes values in between those corresponding to the parent compounds AlN and GaN. Contrary to that, the E_abs of In_0.16Ga_0.84N is red-shifted relative to that of GaN and InN, probably due to ordering and/or phase separation phenomena. The EXAFS analysis results reveal that the first nearest-neighbour shell around the N atom, which consists of Ga atoms, is distorted in both GaN and Al_xGa_1−xN for x<0.5.     

Indium content determination related with structural and optical properties of InGaN layers

We studied the structural and optical properties of a set of nominally undoped epitaxial single layers of In_xGa_1−xN (0<x0.2) grown by MOCVD on top of GaN/Al₂O₃ substrates. A comparison of composition values obtained for thin (tens of nanometers) and thick (≈0.5 μm) layers by different analytical methods was performed. It is shown that the indium mole fraction determined by X-ray diffraction, measuring only one lattice parameter strongly depend on the assumptions made about strain, usually full relaxation or pseudomorphic growth. The results attained under such approximations are compared with the value of indium content derived from Rutherford backscattering spectrometry (RBS). It is shown that significant inaccuracies may arise when strain in In_xGa_1−xN/GaN heterostructures is not properly taken into account. Interpretation of these findings, together with the different criteria used to define the optical bandgap of In_xGa_1−xN layers, may explain the wide dispersion of bowing parameters found in the literature. Our results indicate a linear, E_g(x)=3.42−3.86x eV (x0.2), “anomalous” dependence of the optical bandgap at room temperature with In content for In_xGa_1−xN single layers.     

Impedance spectroscopy analysis of AlGaN/GaN HFET structures

For HFET application a series of samples with 30 nm Al_xGa_1−xN (x=0.02–0.4) layers deposited at 1040°C onto optimised 2 μm thick undoped GaN buffers were fabricated. The Al_xGa_1−xN/GaN heterostructures were grown on c-plane sapphire in an atmospheric pressure, single wafer, vertical flow MOVPE system. Electrical properties of the Al_xGa_1−xN/GaN heterostructures and thick undoped GaN layers were evaluated by impedance spectroscopy method performed in the range of 80 Hz–10 MHz with an HP 4192A impedance meter using a mercury probe. The carrier concentration distribution through the layer thickness and the sheet carrier concentration were evaluated. A non-destructive, characterisation technique for verification of device heterostucture quality from the measured C–V and G–V versus frequency characteristics of the heterostructure is proposed.     

Design and optimisation of AlxGa1−xAs/AlyGa1−yAs multilayer structures for visible wavelength applications

Quantum wells with excitonic features in the visible wavelength range were designed using the Al_xGa_1−xAs/Al_yGa_1−yAs material system, and grown using low pressure metal organic vapour phase epitaxy. Characterisation of these quantum well samples was carried out by using photovoltaic spectroscopy, photoluminescence, differential reflectance or photoreflectance techniques. These measurements showed that excitonic absorption in the 520–630 nm range could be achieved using these AlGaAs quantum wells.     

Photocurrent measurements on GaAs1−xNx epilayers grown by metalorganic chemical vapor deposition

GaAs_1−xN_x epilayers were grown on a GaAs(0 0 1) substrate by metalorganic chemical vapor deposition. Composition was determined by high resolution X-ray diffraction. Band gap was measured from 77 to 400 K by using photocurrent measurements. The photocurrent spectra show clear near-band-edge peak and their peak energies drastically decrease with increasing nitrogen composition due to band gap bowing in the GaAs_1−xN_x epilayers. Those red shifts were particularly notable for low nitrogen compositions. However, the shifts tended to saturate when the nitrogen composition become higher than 0.98%. When the nitrogen composition is in the range 1.68–3.11%, the measured temperature dependence of the energy band gap was nicely fitted. However, the properties for the nitrogen composition range 0.31–0.98% could not be fitted with a single fitting model. This result indicates that the bowing parameter reaches 25.39 eV for low nitrogen incorporation (x=0.31%), and decreases with increasing nitrogen composition.     

AlGaN photodetectors grown on Si(1 1 1) by molecular beam epitaxy

The fabrication and characterisation of Al_xGa_1−xN (0x0.35) photodetectors grown on Si(1 1 1) by molecular beam epitaxy are described. For low Al contents (<10%), photoconductors show high responsivities (10A/W), a non-linear dependence on optical power and persistent photoconductivity (PPC). For higher Al contents the PPC decreases and the photocurrent becomes linear with optical power. Schottky photodiodes present zero-bias responsivities from 12 to 5 mA/W (x=0−0.35), a UV/visible contrast higher than 10³, and a time response of 20 ns, in the same order of magnitude as for devices on sapphire substrate. GaN-based p–n ultraviolet photodiodes on Si(1 1 1) are reported for the first time.     

XPS and electroluminescence studies on SrS1−xSex and ZnS1−xSex thin films deposited by atomic layer deposition technique

SrS_1−xSe_x and ZnS_1−xSe_x thin films were deposited by the atomic layer deposition (ALD) technique using elemental selenium as the Se source, thus avoiding use of H₂Se or organometallic selenium compounds. X-ray diffraction (XRD) analysis showed that the films were solid solutions and X-ray photoelectron spectroscopy (XPS) data showed that the surface of both ZnS_1−xSe_x and SrS_1−xSe_x were covered with an oxide and carbon-containing contaminants from exposure to air. The oxidation of SrS_1−xSe_x extended into the film and peak shifts from sulfate were found on the surface. Luminance measurements showed that emission intensity of the ZnS_1−xSe_x:Mn alternating current thin film electroluminescent (ACTFEL) devices at fixed voltage was almost the same as that of the ZnS:Mn device, while emission intensity of the SrS_1−xSe_x:Ce devices decreased markedly as compared to the SrS:Ce device. Emission colors of the devices were altered only slightly due to selenium addition.     

Thermodynamic analysis of the MOVPE growth of InxGa1−xN

A chemical equilibrium model is applied to the growth of the In_xGa_1−xN alloy grown by metalorganic vapor-phase epitaxy (MOVPE). The equilibrium partial pressures and the phase diagram of deposition are calculated for the In_xGa_1−xN alloy. The vapor-solid distribution relationship is discussed in comparison with the experimental data reported in the literature. It is shown that the solid composition of the In_xGa_1−xN alloy grown by MOVPE is thermodynamically controlled and that the incorporation of group III elements into the solid phase deviates from a linear function of the input mole ratio of the group III metalorganic sources under the conditions of high mole fraction of decomposed NH₃ (high value of ), high temperature and low input V/III ratio. The origin of the deviation of the solid composition from the linear relation is also discussed.     

Strain-compensated quantum cascade lasers operating at room temperature

Quantum cascade (QC) lasers based on strain-compensated In_xGa_(1−x)As/In_yAl_(1−y)As grown on InP substrate using molecular beam epitaxy is reported. The epitaxial quality is demonstrated by the abundant narrow satellite peaks of double-crystal X-ray diffraction and cross-section transmission electron microscopy of the QC laser wafer. Laser action in quasi-continuous wave operation is achieved at λ≈3.6–3.7μm at room temperature (34°C) for 20 μm×1.6 mm devices, with peak output powers of 10.6 mW and threshold current density of 2.7 kA/cm² at this temperature.     

Elastic properties of GexAsySe100−x−y glasses

The elastic properties of Ge_xAs_ySe_100−x−y (0x30; 10y40) glasses have been studied. The results were analyzed in terms of the dependence on the theoretical mean coordination number (mean number of covalent bonds per atom) m (m=2+(2x+y)×0.01). Three ranges of m (2.1m2.51, 2.51<m2.78, 2.78<m3) were revealed, where different dependencies of elastic moduli (Young’s modulus, shear modulus) and Poisson’s ratio of glasses on m were observed.     

Anomalous behavior of excess energy curves of InxGa1−xN grown on GaN and InN

We worked out the excess energies for bulk In_xGa_1−xN and In_xGa_1−xN thin films on GaN and InN in order to investigate their thermodynamic stabilities. It has been found that the excess energy maximum shifted toward x0.80 for InGaN/GaN and x0.10 for InGaN/InN due to the lattice constraint in contrast with x0.50 for bulk. Moreover, it has been revealed that the excess energy for InGaN/GaN is larger than that for bulk at x>0.65. This suggests that In-rich films are less stable on GaN than bulk state. These results indicate that the lattice constraint has a significant influence on thermodynamic stabilities of thin films.     

Structure and optical properties of self-assembled InAs/GaAs quantum dots with In0.15Ga0.85As underlying layer

A high density of 1.02×10¹¹ cm⁻² of InAs islands with In_0.15Ga_0.85As underlying layer has been achieved on GaAs (1 0 0) substrate by solid source molecular beam epitaxy. Atomic force microscopy and PL spectra show the size evolution of InAs islands. A 1.3 μm photoluminescence (PL) from InAs islands with In_0.15Ga_0.85As underlying layer and InGaAs strain-reduced layer has been obtained. Our results provide important information for optimizing the epitaxial structures of 1.3 μm wavelength quantum dots devices.     

AlGaN-based UV photodetectors

Al_xGa_1−xN alloys are very attractive materials for application to ultraviolet photodetection. AlGaN photoconductors, Schottky photodiodes, metal–semiconductor–metal photodiodes, p–n junction photodetectors and phototransistors have been recently developed. In this work we analyse the performance of AlGaN-based photodetectors, discussing present achievements, and comparing the characteristics of the various photodetector structures developed to date.     

Non-linear As(P) incorporation in GaAs1−yPy on GaAs and InAs1−yPy on InP

We find anion incorporation into both GaAs_1−yP_y on GaAs and InAs_1−yP_y on InP during gas source molecular beam epitaxy (GSMBE) is not linearly related to the hydride gas fluxes within our reactor. The deviation from an ideal model, i.e., y = ƒ_P/(ƒ_P+ƒ_As), where As(P) is the flux of AsH₃ (PH₃), can be as large as a factor of two. GaAsP exhibits the largest degree of nonlinearity and incorporation is found to depend quadratically on the fluxes over a wide range of flux ratio. Significant deviations are also found for InAsP; however, anion incorporation can be modeled with y = ƒ_P/(ƒ_P+βƒ_As).     

Formation mechanism of InxGa1−xAs bridge layers on patterned GaAs substrates

The formation mechanism of In_xGa_1−xAs (x=0.06) bridge layers on patterned GaAs (1 1 1)B substrates using liquid-phase epitaxy has been investigated. For this (i) the effect of density gradient in the solution on the formation of bridge layer and (ii) growth of bridge layer on 1 1 0 line-seed-substrates were studied. The convection induced by destabilizing density gradient in the solution led to an increase of lateral growth rate of the InGaAs bridge layers on a substrate mounted on the upper portion of the solution. However, it did not have any significant effect on the formation of the bridge layers. The formation of bridge layer on 1 1 0 line-seed-substrate took place only for the {1 1 1}B growth fronts, which indicated that “Berg effect” is responsible for the formation of bridge layers.     

Investigation of metal–GaN and metal–AlGaN contacts by XPS depth profiles and by electrical measurements

Metal/GaN Schottky contacts have been studied by X-ray photoelectron spectroscopy (XPS). Au/GaN, Pt/GaN, Pd/GaN are sharp while Ti/GaN is diffuse with the following composition, starting from the surface: Ti+TiN, Ti+Ti_xGa_yN, Ti+Ti_xGa_yN+Ga, GaN+Ga. Au/AlGaN and Ni/AlGaN contacts are much broader than Au/GaN: Al and Ga are found more than 100 Å away from the interface. Schottky barrier height was measured for the Au/GaN, Pd/GaN, Pt/GaN, Au/AlGaN and Ni/AlGaN contacts.     

Electrical conductivity and photoreflectance of nanocrystalline copper nitride thin films deposited at low temperature

Nanocrystalline thin films of copper nitride were grown on Si (1 0 0) wafers at a low substrate temperature by reactive magnetron sputtering of Cu target with the mixture of nitrogen and argon. The influence of nitrogen deficiency upon the structural, optical and electrical properties of as-deposited films was investigated. X-ray diffraction confirms the presence of cubic Cu₃N and Cu biphases irrespective of carefully optimized processing parameters. With a Cu content approaching the stoichiometry for Cu₃N, the films assume a smooth morphology with densely-packed nanocrystallites of about 40–60 nm in size. Those deposits containing more than 79% Cu are metallic conductors with excellent electrical conductivity via a percolation mechanism, whereas the slightly substoichiometric Cu₃N films show a typical behavior of deficit semiconductor, with an optical gap of about 1.85 eV as revealed by photoreflectance measurement. All the observations are discussed in terms of nitrogen reemission from the growing film.     

The incorporation behavior of arsenic and antimony in GaAsSb/GaAs grown by solid source molecular beam epitaxy

GaAsSb ternary epitaxial layers were grown on GaAs (0 0 1) substrate in various Sb₄/As₂ flux ratios by solid source molecular beam epitaxy. The alloy compositions of GaAs_1−ySb_y were inferred using high-resolution X-ray symmetric (0 0 4) and asymmetric (2 2 4) glance exit diffraction. The non-equilibrium thermodynamic model is used to explain the different incorporation behavior between the Sb₄ and As₂ under the assumption that one incident Sb₄ molecule produces one active Sb₂ molecule. It is inferred that the activation energy of Sb₄ dissociation is about 0.46 eV. The calculated results for the incorporation efficiency of group V are in good agreement with the experimental data.     

The effect of the AlxGa1−xN/AIN buffer layer on the properties of GaN/Si(1 1 1) film grown by NH3-MBE

We describe the growth of GaN on Si(1 1 1) substrates with Al_xGa_1−xN/AlN buffer layer by ammonia gas source molecular beam epitaxy (NH₃-GSMBE). The influence of the AlN and Al_xGa_1−xN buffer layer thickness and the Al composition on the crack density of GaN has been investigated. It is found that the optimum thickness is 120 and 250 nm for AlN and Al_xGa_1−xN layers, respectively. The optimum Al composition is between 0.3<x<0.6.     

A study of growth and morphological features of TiOxNy thin films prepared by MOCVD

The growth and morphological features of MOCVD TiO_xN_y films have been characterized to evaluate the effect of various process parameters on film growth. XRD analysis of the films deposited at 600°C on Si(1 1 1) and mica show a TiN(1 1 1) peak at 2θ=36.6°, but only anatase peaks are detected below 550°C. Above 650°C, both anatase and rutile peaks are detected. The presence of ammonia is not effective below 550°C as the deposited film is mostly TiO₂. Also, ammonia does not play any role in homogeneous nucleation in the gas phase, as evident by the deposition of anatase/rutile particles above 650°C. The following changes in the morphological features are observed by varying process parameters. By increasing the ratio of titanium-isopropoxide to ammonia flow, the cluster shape changes from angular to rounded; dilution of the flow results in larger elongated clusters; increase in flow rate at constant precursor to ammonia ratios, changes the cluster shape from rounded to elongated and the cluster size deceases. Deposition at higher temperatures results in finer clusters with a slower growth rate and eventually results in a very thin film with particle deposition at 650°C and above.